PIT isn't available on some of new hardware including Hyper-V. So
use pmtimer for calibration. Moreover pmtimer calibration is faster, so
use it on coreboor where booting time is important.
Based on patch by Michael Chang.
9be4c45dbe added switch case between
fall through cases, causing all memory regions of unknown type to be
marked as available.
Move default case into its own block and add explicit FALLTHROUGH
annotation.
Reported by Elliott, Robert (Persistent Memory) <elliott@hpe.com>
We were resetting nb->data every time we tried a new server, but we need to do
it every time we try for a different record, otherwise we don't end up falling
back to the A record properly. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
This makes it impossible to read from stdin without controlling tty:
10:/mnt # echo -e passwd\\npasswd | setsid ./grub-mkpasswd-pbkdf2
Enter password:
Reenter password: ./grub-mkpasswd-pbkdf2: error: failure to read password.
10:/mnt
It is not possible to configure encrypted containers on multiple partitions of
the same disk; after the first one all subsequent fail with
disk/cryptodisk.c:978: already mounted as crypto0
Store partition offset in cryptomount descriptor to distinguish between them.
From original patch by dann frazier <dann.frazier@canonical.com>:
grub_net_fs_open() saves off a copy of the file structure it gets passed and
uses it to create a bufio structure. It then overwrites the passed in file
structure with this new bufio structure. Since file->name doesn't get set
until we return back to grub_file_open(), it means that only the bufio
structure gets a valid file->name. The "real" file's name is left
uninitialized. This leads to a crash when the progress module hook is called
on it.
grub_net_fs_open() already saved copy of file name as ->net->name, so change
progress module to use it.
Also, grub_file_open may leave file->name as NULL if grub_strdup fails. Check
for it.
Also-By: dann frazier <dann.frazier@canonical.com>
It cannot work anyway because host disk cannot be read. This fixes hostfs access
on native Windows build where filenames start with '\' or do not have initial
separator at all (d:\foo).
Issue was observed when running grub-fstest on Windows. On UNIX image name is
canonicalized to always start with `/' so this was not noticed.
This has side effect of allowing relative path names on host, but this already
was the case with `ls' command, so it just extends it to all commands.
Reported-By: Arch Stack <archstacker@gmail.com>
Also-By: Arch Stack <archstacker@gmail.com>
sun4v vnet devices do not implement the support of duplex and speed
instance attributes. An attempt to open such a device with
the attributes will fail:
ok select net:speed=auto,duplex=auto
Unknown key 'speed'
Unknown key 'duplex'
Manual Configuration: Host IP, boot server and filename must be specified
WARNING: /virtual-devices@100/channel-devices@200/network@0: Can't open OBP standard TFTP package
Can't open device
ok
Therefore, let's not set SUFFIX for such devices.
Signed-off-by: Stanislav Kholmanskikh <stanislav.kholmanskikh@oracle.com>
The EFI spec indicates that get_status() should return the address of the buffer
we passed into transmit to indicate the the buffer was transmitted. However we
have boxes where the firmware returns some arbitrary address instead, which
makes grub think that we've not sent anything. So since we have the SNP stuff
opened in exclusive mode just assume any non-NULL txbuf means that our transmit
occurred properly. This makes grub able to do its networking stuff properly on
our broken firmware. Thanks,
cc: Peter Jones <pjones@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
