The path returned by grub_efi_net_config has already been stripped for the
directory part extracted from cached bootp packet. We should just return the
result to avoild it be stripped again.
It fixed the problem that grub.efi as NBP image always looking for grub.cfg and
platform directory in upper folder rather than current one it gets loaded while
$prefix is empty. The behavior is inconsistent with other architecture and how
we would expect empty $prefix going to be in general.
The only exception to the general rule of empty $prefix is that when loaded
from platform directory itself, the platform part is stripped thus upper folder
is used for looking up files. It meets the case for how grub-mknetdir lay out
the files under tftp root directory, but also hide away this issue to be
identified as it appears to be just works.
Also fix possible memory leak by moving grub_efi_get_filename() call after
grub_efi_net_config().
We only support FDT files with EFI on arm and arm64 systems, not
on x86. So move the helper that finds a prepopulated FDT UUID
into its own file and only build it for architectures where it
also gets called.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Searching for a device tree that EFI passes to us via configuration tables
is nothing architecture specific. Move it into generic code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Prevent buffer over-read in grub_machine_mmap_iterate. This was
causing phys_base from being calculated properly. This then
caused the wrong value to be placed in ramdisk_image within
struct linux_hdrs. Which prevented the ramdisk from loading on
boot.
Newer SPARC systems contain more than 8 available memory entries.
For example on a T5-8 with 2TB of memory, the memory layout could
look like this:
T5-8 Memory
reg 00000000 30000000 0000003f b0000000
00000800 00000000 00000040 00000000
00001000 00000000 00000040 00000000
00001800 00000000 00000040 00000000
00002000 00000000 00000040 00000000
00002800 00000000 00000040 00000000
00003000 00000000 00000040 00000000
00003800 00000000 00000040 00000000
available 00003800 00000000 0000003f ffcae000
00003000 00000000 00000040 00000000
00002800 00000000 00000040 00000000
00002000 00000000 00000040 00000000
00001800 00000000 00000040 00000000
00001000 00000000 00000040 00000000
00000800 00000000 00000040 00000000
00000000 70000000 0000003f 70000000
00000000 6eef8000 00000000 00002000
00000000 30400000 00000000 3eaf6000
name memory
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
all_video module does not have any code or data and exists solely for
.moddeps section to pull in dependencies. This makes all symbols unneeded.
While in current binutils (last released version as of this commit is 2.26)
``strip --strip-unneeded'' unintentionally adds section symbols for each
existing section, this behavior was considered a bug and changed in commit
14f2c699ddca1e2f706342dffc59a6c7e23e844c to completely strip symbol table
in this case.
Older binutils (verified with 2.17) and some other toolchains (at least
elftoolchain r3223M), both used in FreeBSD, remove symbol table in all_video
as well.
Relax run-time check and do not return error for modules without symbol table.
Add additional checks to module verifier to make sure such modules
a) have non-empty .moddeps section. Without either externally visible symbols
or .moddeps modules are completely useless and should not be built.
b) do not have any relocations.
Closes: 46986
v2: add run-time check for empty symbol table if relocations are present as
suggested by Vladimir.
Condition was apparently reversed so GRUB assumed all devices were
files. This later made it skip BLKFLSBUF ioctl on Linux which caused
various page cache coherency issues. Observed were
- failure to validate blocklist install (read content did not match
just written)
- failure to detect Linux MD on disk after online hot addition
(GRUB got stale superblock)
Closes: 46691
If line contains single word, line and argv[0] are aliases, so
no NULL dereference is possible, but Coverity does not know it.
Change code to avoid ambiguity and also remove redundant call to
grub_strchr.
CID: 86725
Timer event to keep grub msec counter was running at 1000HZ. This was too
fast for UEFI timer driver and resulted in a 10x slowdown in grub time
versus wallclock. Reduce the timer event frequency and increase tick
increment accordingly to keep better time.
Otherwise it causes subsequent file open to fail, because grub_file_open
misinterprets set grub_errno for grub_file_get_device_name failure.
Closes: 46540
Condition was accidentally reversed, so PIT calibration always failed
when PIT was present and always succeeded when PIT was missing, but in
the latter case resulted in absurdly fast clock.
Reported and tested by Vitaly Kuznetsov <vkuznets@redhat.com>
PIT isn't available on some of new hardware including Hyper-V. So
use pmtimer for calibration. Moreover pmtimer calibration is faster, so
use it on coreboor where booting time is important.
Based on patch by Michael Chang.
It cannot work anyway because host disk cannot be read. This fixes hostfs access
on native Windows build where filenames start with '\' or do not have initial
separator at all (d:\foo).
Issue was observed when running grub-fstest on Windows. On UNIX image name is
canonicalized to always start with `/' so this was not noticed.
This has side effect of allowing relative path names on host, but this already
was the case with `ls' command, so it just extends it to all commands.
Reported-By: Arch Stack <archstacker@gmail.com>
Also-By: Arch Stack <archstacker@gmail.com>
mips_attributes was introduced to work around clang problems with
-msoft-float. Those problems are now fixed and moreover .gnu_attributes
itself is unportable and creates problem with clang.
Revert "mips: Fix soft-float handling."
This partially reverts commit 6a4ecd276e.
The current code for EFI grub_exit() calls grub_efi_fini() before
returning to firmware. In the case of ARM, this leaves a timer
event running which could lead to a firmware crash. This patch
changes this so that grub_machine_fini() is called with a NORETURN
flag. This allows machine-specific shutdown to happen as well
as the shutdown done by grub_efi_fini().
Signed-off-by: Mark Salter <msalter@redhat.com>
Use the new thumb_get_instruction_word/thumb_set_instruction_word
helpers throughout.
Style cleanup (missing spaces).
Move Thumb MOVW/MOVT handlers into Thumb relocation section of file.
