66 lines
No EOL
2.8 KiB
Nginx Configuration File
66 lines
No EOL
2.8 KiB
Nginx Configuration File
# vim: ft=nginx
|
|
|
|
# Define two buckets: Once for http1 connections (which we force to shard across our fleet) and
|
|
# one for http2 connections (which will all hit the same node).
|
|
map $http2 $http1_bucket {
|
|
"" $proxy_protocol_addr; # HTTP1 case: use the IP address, since shared across nodes.
|
|
default $request_id; # HTTP2 case: use request ID to "disable" check.
|
|
}
|
|
|
|
map $http2 $http2_bucket {
|
|
"" $request_id; # HTTP1 case: use the request ID to "disable" check.
|
|
default $connection; # HTTP2 case: use the connection serial number to limit.
|
|
}
|
|
|
|
# Define two additional buckets that fall to $request_id (thus no effective rate limiting) if
|
|
# a specific set of namespaces is matched. This allows us to turn off rate limiting selectively
|
|
# for special internal namespaces.
|
|
map $namespace $namespaced_http1_bucket {
|
|
{% for namespace in non_rate_limited_namespaces %}
|
|
"{{ namespace }}" $request_id;
|
|
{% endfor %}
|
|
{% if enable_rate_limits %}
|
|
default $http1_bucket;
|
|
{% else %}
|
|
default $request_id;
|
|
{% endif %}
|
|
}
|
|
|
|
map $namespace $namespaced_http2_bucket {
|
|
{% for namespace in non_rate_limited_namespaces %}
|
|
"{{ namespace }}" $request_id;
|
|
{% endfor %}
|
|
{% if enable_rate_limits %}
|
|
default $http2_bucket;
|
|
{% else %}
|
|
default $request_id;
|
|
{% endif %}
|
|
}
|
|
|
|
{% if enable_rate_limits %}
|
|
limit_req_zone $http_authorization zone=staticauth:10m rate=30r/s;
|
|
{% else %}
|
|
limit_req_zone $request_id zone=staticauth:10m rate=300r/s;
|
|
{% endif %}
|
|
|
|
limit_req_zone $http1_bucket zone=dynamicauth_very_light_http1:10m rate=30r/s;
|
|
limit_req_zone $http2_bucket zone=dynamicauth_very_light_http2:10m rate=600r/s;
|
|
limit_req_zone $namespaced_http1_bucket zone=namespaced_dynamicauth_very_light_http1:10m rate=30r/s;
|
|
limit_req_zone $namespaced_http2_bucket zone=namespaced_dynamicauth_very_light_http2:10m rate=600r/s;
|
|
|
|
limit_req_zone $http1_bucket zone=dynamicauth_light_http1:10m rate=20r/s;
|
|
limit_req_zone $http2_bucket zone=dynamicauth_light_http2:10m rate=400r/s;
|
|
limit_req_zone $namespaced_http1_bucket zone=namespaced_dynamicauth_light_http1:10m rate=20r/s;
|
|
limit_req_zone $namespaced_http2_bucket zone=namespaced_dynamicauth_light_http2:10m rate=400r/s;
|
|
|
|
# This zone should always be used with burst=<number> (nodelay|delay) as the
|
|
# limit is very low on purpose but should allow for the burst of traffic
|
|
# required for a registry operation. The burst number should also vary per
|
|
# endpoint.
|
|
limit_req_zone $http1_bucket zone=dynamicauth_heavy_http1:10m rate=1r/s;
|
|
limit_req_zone $http2_bucket zone=dynamicauth_heavy_http2:10m rate=20r/s;
|
|
limit_req_zone $namespaced_http1_bucket zone=namespaced_dynamicauth_heavy_http1:10m rate=1r/s;
|
|
limit_req_zone $namespaced_http2_bucket zone=namespaced_dynamicauth_heavy_http2:10m rate=20r/s;
|
|
|
|
limit_req_status 429;
|
|
limit_req_log_level warn; |