[ Upstream commit 893b24181b ]
The FFR is a predicate register which can vary between 16 and 256 bits
in size depending upon the configured vector length. When saving the
SVE state in streaming SVE mode, the FFR register is inaccessible and
so commit 9f58486657 ("arm64/sve: Make access to FFR optional") simply
clears the FFR field of the in-memory context structure. Unfortunately,
it achieves this using an unconditional 8-byte store and so if the SME
vector length is anything other than 64 bytes in size we will either
fail to clear the entire field or, worse, we will corrupt memory
immediately following the structure. This has led to intermittent kfence
splats in CI [1] and can trigger kmalloc Redzone corruption messages
when running the 'fp-stress' kselftest:
| =============================================================================
| BUG kmalloc-1k (Not tainted): kmalloc Redzone overwritten
| -----------------------------------------------------------------------------
|
| 0xffff000809bf1e22-0xffff000809bf1e27 @offset=7714. First byte 0x0 instead of 0xcc
| Allocated in do_sme_acc+0x9c/0x220 age=2613 cpu=1 pid=531
| __kmalloc+0x8c/0xcc
| do_sme_acc+0x9c/0x220
| ...
Replace the 8-byte store with a store of a predicate register which has
been zero-initialised with PFALSE, ensuring that the entire field is
cleared in memory.
[1] https://lore.kernel.org/r/CA+G9fYtU7HsV0R0dp4XEH5xXHSJFw8KyDf5VQrLLfMxWfxQkag@mail.gmail.com
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 9f58486657 ("arm64/sve: Make access to FFR optional")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20230628155605.22296-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bfbff9b46 ]
The bootrom burned into the MT7986 SoC will try multiple locations on
the SPI-NAND flash to load bl2 in case the bl2 image located at the the
previously attempted offset is corrupt.
Use 0x100000 instead of 0x80000 as partition size for bl2 on SPI-NAND,
allowing for up to four redundant copies of bl2 (typically sized a
bit less than 0x40000).
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZH9UGF99RgzrHZ88@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4366b5695 ]
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A76) cluster at a maximum of 2200MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculated the mean result for each cluster
4. Calculated DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scaled results to 1024:
result_c0 = dmips_mhz_c0 / dmips_mhz_c1 * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 12016411 Dhry/s
Cluster 1 (BIG): 31702034 Dhry/s
The calculated scaled results are:
Cluster 0: 426.953226899238 (rounded to 427)
Cluster 1: 1024
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230602183515.3778780-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38c6ced4e ]
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: 635fb18ba0 ("arch: arm64: dts: Add support for AM69 Starter Kit")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c10a9df30e ]
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: e20a06aca5 ("arm64: dts: ti: Add support for J784S4 EVM board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155e7635ed ]
Mailbox nodes are now disabled by default. The BeagleBoard AI64 DT
addition went in at around the same time and must have missed that
change so the mailboxes are not re-enabled. Do that here.
Fixes: fae14a1cb8 ("arm64: dts: ti: Add k3-j721e-beagleboneai64")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11a1397bbf ]
The USB HC node is missing the interconnect paths, so add them.
Fixes: 7f7e5c1b03 ("arm64: dts: qcom: sm8550: Add USB PHYs and controller nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230601103817.4066446-1-abel.vesa@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 223ce29c8b ]
The framebuffer configuration for edo pdx203, written in edo dtsi (which
is overwritten in pdx206 dts for its smaller panel) has to use a
1096x2560 configuration as this is what the panel (and framebuffer area)
has been initialized to. Downstream userspace also has access to (and
uses) this 2.5k mode by default, and only switches the panel to 4k when
requested.
This is similar to commit be8de06dc3 ("arm64: dts: qcom:
sm8150-kumano: Panel framebuffer is 2.5k instead of 4k") which fixed the
same for the previous generation Sony platform.
Fixes: 69cdb97ef6 ("arm64: dts: qcom: sm8250: Add support for SONY Xperia 1 II / 5 II (Edo platform)")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230606211418.587676-1-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b2c7ac8e4 ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: ffc50b2d38 ("arm64: dts: qcom: Add base SM8550 dtsi")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-8-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91e83140b5 ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: c83545d953 ("arm64: dts: sdm845: Add rpmh-rsc node")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-6-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b04cbd81b ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: 07c8ded6e3 ("arm64: dts: qcom: add sdm670 and pixel 3a device trees")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-5-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab033e7846 ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: 6bd20c54b5 ("arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-3-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a2c4e5635 ]
The schematics are misleading, the flow control is for HSCIF1. We need
SCIF1 for GNSS/GPS which does not use flow control.
Fixes: c6c816e22b ("arm64: dts: ulcb-kf: enable SCIF1")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230525084823.4195-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42127f578e ]
Firmware shipped on mt8183 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.3.I525a2ed4260046d43c885ee1275e91707743df1c@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83022f6484 ]
This file is using definitions from the spmi-vadc header, so we need to
include it.
Fixes: 11975b9b81 ("arm64: dts: qcom: Add pm7250b PMIC")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-pm7250b-sid-v1-1-fc648478cc25@fairphone.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5500f823db ]
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27654df20 ]
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a0156b886 ]
Add missing reg property to touchscreen child node to fix dtbs W=1 warnings:
Warning (unit_address_vs_reg): /soc@0/geniqup@ac0000/i2c@a98000/touchscreen@20/rmi4-f12@12: node has a unit name, but no reg or ranges property
Fixes: be497abe19 ("arm64: dts: qcom: Add support for Xiaomi Mi Mix2s")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Molly Sophia <mollysophia379@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230419211856.79332-18-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e47a807843 ]
Add a family compatible for QCE IP on SM8550 SoC, which is equal to QCE IP
found on SM8150 SoC and described in the recently updated device tree
bindings documentation, as well add a generic QCE IP family compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: 3cbf49ef16 ("arm64: dts: qcom: sm8550: correct crypto unit address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3244442406 ]
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
Stable-dep-of: 1f9a41bb0b ("arm64: dts: qcom: msm8916: correct WCNSS unit address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9ef7a805a ]
Unlike typical GIC interrupts, first cell for SPMI interrupts is the
USID rather than GIC_SPI/GIC_PPI/GIC_LPI qualifier. Fix the resin
interrupt to use USID value 0x0 rather than GIC_SPI define.
Fixes: f86ae6f23a ("arm64: dts: qcom: sagit: add initial device tree for sagit")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230409182145.122895-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70be83708c ]
PSCI is not implemented on SparX-5 at all, there is no ATF and U-boot that
is shipped does not implement it as well.
I have tried flashing the latest BSP 2022.12 U-boot which did not work.
After contacting Microchip, they confirmed that there is no ATF for the
SoC nor PSCI implementation which is unfortunate in 2023.
So, disable PSCI as otherwise kernel crashes as soon as it tries probing
PSCI with, and the crash is only visible if earlycon is used.
Since PSCI is not implemented, switch core bringup to use spin-tables
which are implemented in the vendor U-boot and actually work.
Tested on PCB134 with eMMC (VSC5640EV).
Fixes: 6694aee00a ("arm64: dts: sparx5: Add basic cpu support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230221105039.316819-1-robert.marko@sartura.hr
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ae870a68b5 upstream.
This converts arm64 to use the new page fault helper. It was very
straightforward, but still needed a fix for the "obvious" conversion I
initially did. Thanks to Suren for the fix and testing.
Fixed-and-tested-by: Suren Baghdasaryan <surenb@google.com>
Unnecessary-code-removal-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1caa71a7a6 upstream.
When reworking the vgic locking, the vgic distributor registration
got simplified, which was a very good cleanup. But just a tad too
radical, as we now register the *native* vgic only, ignoring the
GICv2-on-GICv3 that allows pre-historic VMs (or so I thought)
to run.
As it turns out, QEMU still defaults to GICv2 in some cases, and
this breaks Nathan's setup!
Fix it by propagating the *requested* vgic type rather than the
host's version.
Fixes: 59112e9c39 ("KVM: arm64: vgic: Fix a circular locking issue")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
link: https://lore.kernel.org/r/20230606221525.GA2269598@dev-arch.thelio-3990X
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16bd455d08 ]
The WCD938x audio codec Soundwire interface part is not a DAI and does
not allow sound-dai-cells:
sc7280-herobrine-crd.dtb: codec@0,4: '#sound-dai-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230220095401.64196-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca8fc68148 ]
The WCD938x audio codec Soundwire interface part is not a DAI and does
not allow sound-dai-cells:
sc7280-idp.dtb: codec@0,4: '#sound-dai-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230220095401.64196-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9ae4a007 ]
In pre-production prototypes (of which I only know one person
having one, Peter Geis), GPIO0 pin A5 was tied to the SDMMC
power enable pin on the CM4 connector. On all production models,
this is not the case; instead, this pin is used for the nEXTRST
signal, and the SDMMC power enable pin is always pulled high.
Since everyone currently using the SOQuartz device trees will
want this change, it is made to the tree without splitting the
trees into two separate ones of which users will then inevitably
choose the wrong one.
This fixes USB and PCIe on a wide variety of CM4IO-compatible
boards which use the nEXTRST signal.
Fixes: 5859b5a9c3 ("arm64: dts: rockchip: add SoQuartz CM4IO dts")
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20230421152610.21688-1-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8681f71759 ]
Restore the host's PMUSERENR_EL0 value instead of clearing it,
before returning back to userspace, as the host's EL0 might have
a direct access to PMU registers (some bits of PMUSERENR_EL0 for
might not be zero for the host EL0).
Fixes: 83a7a4d643 ("arm64: perf: Enable PMU counter userspace access for perf event")
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230603025035.3781797-2-reijiw@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 568a67e742 upstream.
The register and range mappings for the PCIe controller in Rockchip's
RK356x SoCs are incorrect. Replace them with corrected values from the
vendor BSP sources, updated to match current DT schema.
These values are also used in u-boot.
Fixes: 66b51ea7d7 ("arm64: dts: rockchip: Add rk3568 PCIe2x1 controller")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20230601132516.153934-1-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon