Mailbox channels for the base protocol are setup during probe.
There can be a scenario where probe fails to acquire the base
protocol due to a timeout leading to cleaning up of all device
managed memory including the scmi_mailbox structure setup during
mailbox_chan_setup function.
| arm-scmi soc:qcom,scmi: timed out in resp(caller: version_get+0x84/0x140)
| arm-scmi soc:qcom,scmi: unable to communicate with SCMI
| arm-scmi: probe of soc:qcom,scmi failed with error -110
Now when a message arrives at cpu slightly after the timeout, the mailbox
controller will try to call the rx_callback of the client and might end
up accessing freed memory.
| rx_callback+0x24/0x160
| mbox_chan_received_data+0x44/0x94
| __handle_irq_event_percpu+0xd4/0x240
This patch frees the mailbox channels setup during probe and adds some more
error handling in case the probe fails.
Link: https://lore.kernel.org/r/1628111999-21595-1-git-send-email-rishabhb@codeaurora.org
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This transport enables communications with an SCMI platform through virtio;
the SCMI platform will be represented by a virtio device.
Implement an SCMI virtio driver according to the virtio SCMI device spec
[1]. Virtio device id 32 has been reserved for the SCMI device [2].
The virtio transport has one Tx channel (virtio cmdq, A2P channel) and
at most one Rx channel (virtio eventq, P2A channel).
The following feature bit defined in [1] is not implemented:
VIRTIO_SCMI_F_SHARED_MEMORY.
The number of messages which can be pending simultaneously is restricted
according to the virtqueue capacity negotiated at probing time.
As soon as Rx channel message buffers are allocated or have been read
out by the arm-scmi driver, feed them back to the virtio device.
Since some virtio devices may not have the short response time exhibited
by SCMI platforms using other transports, set a generous response
timeout.
SCMI polling mode is not supported by this virtio transport since deemed
meaningless: polling mode operation is offered by the SCMI core to those
transports that could not provide a completion interrupt on the TX path,
which is never the case for virtio whose core callbacks can easily call
into core scmi_rx_callback upon messages reception.
[1] https://github.com/oasis-tcs/virtio-spec/blob/master/virtio-scmi.tex
[2] https://www.oasis-open.org/committees/ballot.php?id=3496
Link: https://lore.kernel.org/r/20210803131024.40280-16-cristian.marussi@arm.com
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Co-developed-by: Peter Hilber <peter.hilber@opensynergy.com>
Co-developed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Igor Skalkin <igor.skalkin@opensynergy.com>
[ Peter: Adapted patch for submission to upstream. ]
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
[ Cristian: simplified driver logic, changed link_supplier and channel
available/setup logic, removed dummy callbacks ]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a new opaque void *priv parameter to scmi_rx_callback which can be
optionally provided by the transport layer when invoking scmi_rx_callback
and that will be passed back to the transport layer in xfer->priv.
This can be used by transports that needs to keep track of their specific
data structures together with the valid xfers.
Link: https://lore.kernel.org/r/20210803131024.40280-15-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Some transports are also effectively registered with other kernel subsystem
in order to be properly probed and initialized; as a consequence such kind
of transports, and their related devices, might still not have been probed
and initialized at the time the main SCMI core driver is probed.
Add an optional .link_supplier() transport operation which can be used by
the core SCMI stack to dynamically check if the transport is ready and
dynamically link its device to the SCMI platform instance device.
Link: https://lore.kernel.org/r/20210803131024.40280-13-cristian.marussi@arm.com
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
[ Cristian: reworded commit message ]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add abstractions for future transports using message passing, such as
virtio. Derive the abstractions from the shared memory abstractions.
Abstract the transport SDU through the opaque struct scmi_msg_payld.
Also enable the transport to determine all other required information
about the transport SDU.
Link: https://lore.kernel.org/r/20210803131024.40280-12-cristian.marussi@arm.com
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
[ Cristian: Adapted to new SCMI Kconfig layout, updated Copyrights ]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The maximum number of simultaneously pending messages is a transport
specific quantity that is usually described statically in struct scmi_desc.
Some transports, though, can calculate such number only at run-time after
some initial transport specific setup and probing is completed; moreover
the resulting max message numbers could also be different between rx and
tx channels.
Add an optional get_max_msg() operation so that a transport can report more
accurate max message numbers for each channel type.
The value in scmi_desc.max_msg is still used as default when transport does
not provide any get_max_msg() method.
Link: https://lore.kernel.org/r/20210803131024.40280-11-cristian.marussi@arm.com
Co-developed-by: Peter Hilber <peter.hilber@opensynergy.com>
Co-developed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Igor Skalkin <igor.skalkin@opensynergy.com>
[ Peter: Adapted patch for submission to upstream. ]
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
[ Cristian: refactored how get_max_msg() is used to minimize core changes ]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Upcoming new SCMI transports won't need any kind of shared memory support.
Compile shmem.c only if a shmem based transport is selected.
Link: https://lore.kernel.org/r/20210803131024.40280-10-cristian.marussi@arm.com
Co-developed-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Igor Skalkin <igor.skalkin@opensynergy.com>
[ Peter: Adapted patch for submission to upstream. ]
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
[ Cristian: Adapted patch/commit_msg to new SCMI Kconfig layout ]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add configuration options to be able to select which SCMI transports have
to be compiled into the SCMI stack.
Mailbox and SMC are by default enabled if their related dependencies are
satisfied.
While doing that move all SCMI related config options in their own
dedicated submenu.
Link: https://lore.kernel.org/r/20210803131024.40280-9-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a check for the presence of .poll_done transport operation so that
transports that do not need to support polling mode have no need to provide
a dummy .poll_done callback either and polling mode can be disabled in the
SCMI core for that tranport.
Link: https://lore.kernel.org/r/20210803131024.40280-8-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Make transport operation .clear_channel optional since some transports
do not need it and so avoid to have them implement dummy callbacks.
Link: https://lore.kernel.org/r/20210803131024.40280-7-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Even though in case of asynchronous commands an SCMI platform is
constrained to emit the delayed response message only after the related
message response has been sent, the configured underlying transport could
still deliver such messages together or in inverted order, causing races
due to the concurrent or out-of-order access to the underlying xfer.
Introduce a mechanism to grant exclusive access to an xfer in order to
properly serialize concurrent accesses to the same xfer originating from
multiple correlated messages.
Add additional state information to xfer descriptors so as to be able to
identify out-of-order message deliveries and act accordingly:
- when a delayed response is expected but delivered before the related
response, the synchronous response is considered as successfully
received and the delayed response processing is carried on as usual.
- when/if the missing synchronous response is subsequently received, it
is discarded as not congruent with the current state of the xfer, or
simply, because the xfer has been already released and so, now, the
monotonically increasing sequence number carried by the late response
is stale.
Link: https://lore.kernel.org/r/20210803131024.40280-6-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tokens are sequence numbers embedded in the each SCMI message header: they
are used to correlate commands with responses (and delayed responses), but
their usage and policy of selection is entirely up to the caller (usually
the OSPM agent), while they are completely opaque to the callee (i.e. SCMI
platform) which merely copies them back from the command into the response
message header.
This also means that the platform does not, can not and should not enforce
any kind of policy on received messages depending on the contained sequence
number: platform can perfectly handle concurrent requests carrying the same
identifiying token if that should happen.
Moreover the platform is not required to produce in-order responses to
agent requests, the only constraint in these regards is that in case of
an asynchronous message the delayed response must be sent after the
immediate response for the synchronous part of the command transaction.
Currenly the SCMI stack of the OSPM agent selects a token for the egressing
commands picking the lowest possible number which is not already in use by
an existing in-flight transaction, which means, in other words, that we
immediately reuse any token after its transaction has completed or it has
timed out: this policy indeed does simplify management and lookup of tokens
and associated xfers.
Under the above assumptions and constraints, since there is really no state
shared between the agent and the platform to let the platform know when a
token and its associated message has timed out, the current policy of early
reuse of tokens can easily lead to the situation in which a spurious or
late received response (or delayed_response), related to an old stale and
timed out transaction, can be wrongly associated to a newer valid in-flight
xfer that just happens to have reused the same token.
This misbehaviour on such late/spurious responses is more easily exposed on
those transports that naturally have an higher level of parallelism in
processing multiple concurrent in-flight messages.
This commit introduces a new policy of selection of tokens for the OSPM
agent: each new command transfer now gets the next available, monotonically
increasing token, until tokens are exhausted and the counter rolls over.
Such new policy mitigates the above issues with late/spurious responses
since the tokens are now reused as late as possible (when they roll back
ideally) and so it is much easier to identify such late/spurious responses
to stale timed out transactions: this also helps in simplifying the
specific transports implementation since stale transport messages can be
easily identified and discarded early on in the rx path without the need
to cross check their actual state with the core transport layer.
This mitigation is even more effective when, as is usually the case, the
maximum number of pending messages is capped by the platform to a much
lower number than the whole possible range of tokens values (2^10).
This internal policy change in the core SCMI transport layer is fully
transparent to the specific transports so it has not and should not have
any impact on the transports implementation.
Link: https://lore.kernel.org/r/20210803131024.40280-5-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Some SCMI transport could need to perform some transport specific setup
before they can be used by the SCMI core transport layer: typically this
early setup consists in registering with some other kernel subsystem.
Add the optional capability for a transport to provide a couple of init
and exit functions that are assured to be called early during the SCMI
core initialization phase, well before the SCMI core probing step.
[ Peter: Adapted RFC patch by Cristian for submission to upstream. ]
Link: https://lore.kernel.org/r/20210803131024.40280-4-cristian.marussi@arm.com
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
[ Cristian: Fixed scmi_transports_exit point of invocation ]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Being a while that we have SCMI trace events in the SCMI stack, remove
this debug helper and its call sites.
Link: https://lore.kernel.org/r/20210803131024.40280-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCMI message headers carry a sequence number and such field is sized to
allow for MSG_TOKEN_MAX distinct numbers; moreover zero is not really an
acceptable maximum number of pending in-flight messages.
Fix accordingly the checks performed on the value exported by transports
in scmi_desc.max_msg
Link: https://lore.kernel.org/r/20210712141833.6628-3-cristian.marussi@arm.com
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: updated the patch title and error message]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
scmi_resp_sensor_reading_complete structure is meant to represent an
SCMI asynchronous reading complete message. The readings field with
a 64bit type forces padding and breaks reads in scmi_sensor_reading_get.
Split it in two adjacent 32bit readings_low/high subfields to avoid the
padding within the structure. Alternatively we could to mark the structure
packed.
Link: https://lore.kernel.org/r/20210628170042.34105-1-cristian.marussi@arm.com
Fixes: e2083d3673 ("firmware: arm_scmi: Add SCMI v3.0 sensors timestamped reads")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Kernel doc validation script still complains about the following:
|No description found for return value of 'scmi_get_protocol_device'
|No description found for return value of 'scmi_devm_notifier_register'
|No description found for return value of 'scmi_devm_notifier_unregister'
Fix adding missing Return kernel-doc statements.
Link: https://lore.kernel.org/r/20210712143504.33541-1-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The scmi_linux_errmap buffer access index is supposed to depend on the
array size to prevent element out of bounds access. It uses SCMI_ERR_MAX
to check bounds but that can mismatch with the array size. It also
changes the success into -EIO though scmi_linux_errmap is never used in
case of success, it is expected to work for success case too.
It is slightly confusing code as the negative of the error code
is used as index to the buffer. Fix it by negating it at the start and
make it more readable.
Link: https://lore.kernel.org/r/20210707135028.1869642-1-sudeep.holla@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The bus probe callback calls the driver callback without further
checking. Better be safe than sorry and refuse registration of a driver
without a probe function to prevent a NULL pointer exception.
Link: https://lore.kernel.org/r/20210624095059.4010157-2-sudeep.holla@arm.com
Fixes: 933c504424 ("firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When the driver core calls the probe callback it already checked that
the devices match, so there is no need to call the match callback again.
Link: https://lore.kernel.org/r/20210624095059.4010157-1-sudeep.holla@arm.com
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
- Support for SCMI clocks from the SCMI power domains
- Addition of checks for correct compatibles for shmem devicetree nodes
that were found missing in the process of YAML schema conversion
- Kconfig and associated build fix found when optee transport are being
worked on
- Couple of fixes and cleanups found as with work-in-progress virtio
transport support
The new transports(optee and virtio) themselves are still being worked on
with ongoing reviews, they are not part of this yet
-----BEGIN PGP SIGNATURE-----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=0YWr
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
ARM SCMI updates for v5.14
- Support for SCMI clocks from the SCMI power domains
- Addition of checks for correct compatibles for shmem devicetree nodes
that were found missing in the process of YAML schema conversion
- Kconfig and associated build fix found when optee transport are being
worked on
- Couple of fixes and cleanups found as with work-in-progress virtio
transport support
The new transports(optee and virtio) themselves are still being worked on
with ongoing reviews, they are not part of this yet
* tag 'scmi-updates-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Avoid multiple initialisations of hdr->protocol_id
firmware: arm_scmi: Move reinit_completion from scmi_xfer_get to do_xfer
firmware: arm_scmi: Add delayed response status check
firmware: arm_scmi: Add compatibility checks for shmem node
firmware: arm_scpi: Add compatibility checks for shmem node
firmware: arm_scmi: Fix the build when CONFIG_MAILBOX is not selected
firmware: arm_scmi: Reset Rx buffer to max size during async commands
firmware: arm_scmi: Add SMCCC discovery dependency in Kconfig
firmware: arm_scmi: Add clock management to the SCMI power domain
Link: https://lore.kernel.org/r/20210611075722.2813550-1-sudeep.holla@arm.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Since the hdr->protocol_id is set from the scmi_protocol_instance handle
just before the transfer, there is no need to initialise the same in
scmi_xfer_get_init. Remove the unnecessary initialisations.
Link: https://lore.kernel.org/r/20210608140140.2042257-1-sudeep.holla@arm.com
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Re-using timed out xfers in a loop can lead to issue if completion was
not properly reinitialized. Move reinit_completion from scmi_xfer_get to
do_xfer to avoid the issue.
Link: https://lore.kernel.org/r/20210606221232.33768-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: moved reinit_completion instead of adding another one]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
A successfully received delayed response could anyway report a failure at
the protocol layer in the message status field.
Add a check also for this error condition.
Link: https://lore.kernel.org/r/20210608103056.3388-1-cristian.marussi@arm.com
Fixes: 58ecdf03db ("firmware: arm_scmi: Add support for asynchronous commands and delayed response")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The shared memory node used for communication between the firmware and
the OS should be compatible with "arm,scmi-shmem". Add the check for the
same while parsing the node before fetching the memory regions.
Link: https://lore.kernel.org/r/20210602073851.1005607-2-sudeep.holla@arm.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Cristian Marussi <cristian.marussi@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
During an async commands execution the Rx buffer length is at first set
to max_msg_sz when the synchronous part of the command is first sent.
However once the synchronous part completes the transport layer waits
for the delayed response which will be processed using the same xfer
descriptor initially allocated. Since synchronous response received at
the end of the xfer will shrink the Rx buffer length to the effective
payload response length, it needs to be reset again.
Raise the Rx buffer length again to max_msg_sz before fetching the
delayed response to ensure full response is read correctly from the
shared memory.
Link: https://lore.kernel.org/r/20210601102421.26581-2-cristian.marussi@arm.com
Fixes: 58ecdf03db ("firmware: arm_scmi: Add support for asynchronous commands and delayed response")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: moved reset to scmi_handle_response as it could race with
do_xfer_with_response]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
ARM_SCMI_PROTOCOL depends on either MAILBOX or HAVE_ARM_SMCCC_DISCOVERY,
not MAILBOX alone. Fix the depedency in Kconfig file and driver to
reflect the same.
Link: https://lore.kernel.org/r/20210521134055.24271-1-etienne.carriere@linaro.org
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[sudeep.holla: Minor tweaks to subject and change log]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Clocks requiring non-atomic contexts are supported by the generic clock
PM layer since commit 0bfa0820c2 ("PM: clk: make PM clock layer
compatible with clocks that must sleep"). That means we can have
SCMI-based clocks be managed by the SCMI power domain now.
Link: https://lore.kernel.org/r/5q88n947-pon-4940-3or6-s54o4r361o5s@onlyvoer.pbz
Tested-by: Dien Pham <dien.pham.ry@renesas.com>
Reviewed-by: Gaku Inami <gaku.inami.xh@renesas.com>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
struct scmi_protocol_handle is declared twice, let us remove the duplicate
declaration.
Link: https://lore.kernel.org/r/20210427033031.4580-1-wanjiabing@vivo.com
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
[sudeep.holla: minor updates to the title and the changelog]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Having added the support for SCMI protocols as modules in order to let
vendors extend the SCMI core with their own additions it seems odd to
then force SCMI drivers built on top to use a static device table to
declare their devices since this way any new SCMI drivers addition
would need the core SCMI device table to be updated too.
Remove the static core device table and let SCMI drivers to simply declare
which device/protocol pair they need at initialization time: the core will
then take care to generate such devices dynamically during platform
initialization or at module loading time, as long as the requested
underlying protocol is defined in the devicetree.
Link: https://lore.kernel.org/r/20210316124903.35011-39-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Extend SCMI protocols accounting mechanism to address possible module
usage and add the support to possibly define new protocols as loadable
modules.
Keep the standard protocols built into the SCMI core.
Link: https://lore.kernel.org/r/20210316124903.35011-38-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Rename non devres managed notify_ops to use a naming pattern which exposes
the performed action verb as last token.
No functional change.
Link: https://lore.kernel.org/r/20210316124903.35011-37-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Notification private data is currently accessible via handle->notify_priv,
this data was indeed meant to be private to the notification core support
and not to be accessible by SCMI drivers. Make it private hiding it
inside instance descriptor struct scmi_info and accessible only via
dedicated helpers.
Link: https://lore.kernel.org/r/20210316124903.35011-36-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Remove all the events registration code used to ease the transition to the
new interface based on protocol handles.
Link: https://lore.kernel.org/r/20210316124903.35011-35-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Remove unused core scmi_xfer wrappers now that we have migrated all
protocols to the new interface based on protocol handles.
Link: https://lore.kernel.org/r/20210316124903.35011-34-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all protocols and drivers have been ported to the new interface
based on protocol handles and get/put operations, remove all the legacy
transient initialization code.
Link: https://lore.kernel.org/r/20210316124903.35011-33-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all the protocol private variable data have been moved out of
struct scmi_handle, mark all of its references as const.
Link: https://lore.kernel.org/r/20210316124903.35011-32-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all the SCMI driver users have been migrated to the new interface
remove the legacy interface and all the transient code.
Link: https://lore.kernel.org/r/20210316124903.35011-31-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert internals of protocol implementation to use protocol handles and
expose a new protocol operations interface for SCMI driver using the new
get/put common operations, while keeping the old handle->voltage_ops still
around to ease transition.
Remove handle->voltage_priv now unused.
Link: https://lore.kernel.org/r/20210316124903.35011-29-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert internals of protocol implementation to use protocol handles and
expose a new protocol operations interface for SCMI driver using the new
get/put common operations.
Remove handle->system_priv now unused.
Link: https://lore.kernel.org/r/20210316124903.35011-28-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all the SCMI driver users have been migrated to the new interface
remove the legacy interface and all the transient code.
Link: https://lore.kernel.org/r/20210316124903.35011-27-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert internals of protocol implementation to use protocol handles and
expose a new protocol operations interface for SCMI driver using the new
get/put common operations, while keeping the old handle->sensor_ops still
around to ease transition.
Remove handle->sensor_priv now unused.
Link: https://lore.kernel.org/r/20210316124903.35011-24-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all the SCMI driver users have been migrated to the new interface
remove the legacy interface and all the transient code.
Link: https://lore.kernel.org/r/20210316124903.35011-23-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert internals of protocol implementation to use protocol handles and
expose a new protocol operations interface for SCMI driver using the new
get/put common operations, while keeping the old handle->reset_ops still
around to ease transition.
Remove handle->reset_priv now unused.
Link: https://lore.kernel.org/r/20210316124903.35011-21-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all the SCMI driver users have been migrated to the new interface
remove the legacy interface and all the transient code.
Link: https://lore.kernel.org/r/20210316124903.35011-20-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert internals of protocol implementation to use protocol handles and
expose a new protocol operations interface for SCMI driver using the new
get/put common operations, while keeping the old handle->clk_ops still
around to ease transition.
Remove handle->clock_priv now unused.
Link: https://lore.kernel.org/r/20210316124903.35011-18-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all the SCMI driver users have been migrated to the new interface
remove the legacy interface and all the transient code.
Link: https://lore.kernel.org/r/20210316124903.35011-17-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Port the scmi genpd driver to the new SCMI power interface based on
protocol handles and common devm_get_ops().
Link: https://lore.kernel.org/r/20210316124903.35011-16-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert internals of protocol implementation to use protocol handles and
expose a new protocol operations interface for SCMI driver using the new
get/put common operations, while keeping the old handle->power_ops still
around to ease transition.
Remove handle->power_priv now unused.
Link: https://lore.kernel.org/r/20210316124903.35011-15-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that all the SCMI driver users have been migrated to the new interface
remove the legacy interface and all the transient code.
Link: https://lore.kernel.org/r/20210316124903.35011-14-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert internals of protocol implementation to use protocol handles and
expose a new protocol operations interface for SCMI driver using the new
get/put common operations, while keeping the old handle->perf_ops still
around to ease transition.
Remove handle->perf_priv now unused.
Link: https://lore.kernel.org/r/20210316124903.35011-12-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Port the SCMI base protocol to new protocol handles based interface.
Link: https://lore.kernel.org/r/20210316124903.35011-11-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add an helper to access from a protocol handle, the SCMI version data
which is exposed on sysfs. Such helper will be needed by SCMI base
protocol initialization once it will be moved to new protocol handles
scheme.
Link: https://lore.kernel.org/r/20210316124903.35011-10-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add new core SCMI transfer operations based on protocol handles to
enable protocols to builds and send their own protocol specific messages.
Keep old original scmi_xfer_ operations interface as wrappers around the
new interface in order to let coexist old and new interfaces to ease
protocol by protocol migration.
In order to support such migration the above wrappers and some
additional transient code is also introduced in this commit. It will be
later removed as a whole once the full migration of protocols and SCMI
drivers will have been completed.
Link: https://lore.kernel.org/r/20210316124903.35011-9-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Convert all refactored events registration routines to use protocol
handles.
In order to maintain bisectability and to allow protocols and drivers
to be later ported to the new protocol handle interface one by one,
introduce here also some transient code that will be removed later
in order to ease such transition.
Link: https://lore.kernel.org/r/20210316124903.35011-8-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a new refactored protocol events registration helper and invoke it
from the centralized initialization process triggered by get_ops() and
friends.
Also add a `get_num_sources` as a new optional callback amongst protocol
events operations. Finally remove events registration call-sites from
within the legacy protocol init routines.
Link: https://lore.kernel.org/r/20210316124903.35011-7-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Expose to the SCMI drivers a new alternative devres managed notifications
API based on protocol handles.
All drivers still keep using the old API, no functional change.
Link: https://lore.kernel.org/r/20210316124903.35011-6-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Account for any active registered notifier against the proper related
protocol, do not consider pending event handlers, only active handlers
will concur to protocol usage accounting.
Link: https://lore.kernel.org/r/20210316124903.35011-5-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Expose to the SCMI drivers a new devres managed common protocols API
based on generic get/put methods and protocol handles.
All drivers still keep using the old API, no functional change.
Link: https://lore.kernel.org/r/20210316124903.35011-4-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add basic protocol handles definitions and private data helpers.
A protocol handle identifies a protocol instance initialized against a
specific handle, it embeds all the references to the core SCMI transfer
methods that will be needed by a protocol implementation to build and
send its own protocol specific messages using common core methods.
As such, in the interface, a protocol handle will be passed down from
the core to the protocol specific initialization callback at init time.
Anyways, at this point only definitions are introduced, all protocols
initialization code and SCMI drivers probing is still based on the old
interface, so no functional change.
Link: https://lore.kernel.org/r/20210316124903.35011-3-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Extend common protocol registration routines and provide some new generic
protocols get/put helpers that can track protocols usage and automatically
perform the proper initialization and de-initialization on demand when
required.
Convert all standard protocols to use this new registration scheme while
keeping them all still using the usual initialization logic bound to SCMI
devices probing.
Link: https://lore.kernel.org/r/20210316124903.35011-2-cristian.marussi@arm.com
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This change provides ARM SCMI Protocol based IIO device.
This driver provides support for Accelerometer and Gyroscope using
SCMI Sensor Protocol extensions added in the SCMIv3.0 ARM specification
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jyoti Bhayana <jbhayana@google.com>
Link: https://lore.kernel.org/r/20210212172235.507028-2-jbhayana@google.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210309231259.78050-2-jbhayana@google.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SMC/HVC SCMI transport is modified to allow the completion of an
SCMI message to be indicated by an interrupt rather than the return of
the smc/hvc call. This accommodates the existing behavior of the
BrcmSTB SCMI "platform".
Link: https://lore.kernel.org/r/20201222145603.40192-3-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
[sudeep.holla: added call to reinit_completion, whitespace cleanup, dropped
irrelavant info in the commit log]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
Add a new interface to the existing perf_ops and export the information
about the power values scale.
This would be used by the cpufreq driver and Energy Model framework to
set the performance domains scale: milli-Watts or abstract scale.
Suggested-by: Morten Rasmussen <morten.rasmussen@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SCMI v3.0 voltage domain protocol support to discover the voltage levels
supported by the domains and to set/get the configuration and voltage
level of any given domain.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAl+7jkIACgkQAEG6vDF+
4pio2Q/+OjxDa7S5i/b+9z3ZWNopE3Ka1Xm5F7nJH3FTw7Py2Ae4fh9Cu4Yka2he
u8jdkin2D/RhYLQw5+mYC+2731r7AIZvGMPfWZv0jWa275Qcv6cBItPXjowGVERM
E/KTC6m2sEH3gqIC7wF0qqsW90srPDzxYeL/rTWa5JrMqbGWcAvbepIm7TJA0Ea3
JMzxTXI0KhadtiGiDhijR1u+vheqr7WdgAzib+dUteqelin8h2KRgMdLNod8KY7U
IfNSyfzA23HPV0bQVWTp9U9f+mypQB6JnriaNOQyXMdm9CCQKpSdnvQqwa2DarSk
yv6leHqhZr667EWOsMWrh1c3K5Jr8fd1NZ4z/gMUGpac8VBx3N2ahmE9/4W4vuYy
Lh5R1b7dQmVP1n0k0OkZdDhGCbG4Gu/Yd3gwPNlFTKmuHcv1BTwb9gqT52nlxS1N
+K3+F9k9NPlssoVANTycYzvobumf6wizkbgavgz1sPjcjzpE8yoyf8FlTX8Akdcb
qcbXmPTKe/TSlrmLc1Rq0p+uk19+iSo5KjjsxJUw+7X+P/fHDjeopmNrQrdzUuHA
0D4K+koUhrBoGTq/h7pbFYIXjIE877PEilOQGV9eDWaZm6Q1+ZHD4Veg4R2aREZ3
HCY9H87/oXW0XWtlWH3cL3p5RuMJD1kJlltCg87NCRtNxeVK3nQ=
=mENP
-----END PGP SIGNATURE-----
Merge tag 'scmi-voltage-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into for-next/scmi
SCMI voltage domain management protocol support for v5.11
SCMI v3.0 voltage domain protocol support to discover the voltage levels
supported by the domains and to set/get the configuration and voltage
level of any given domain.
* tag 'scmi-voltage-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Add support to enumerated SCMI voltage domain device
firmware: arm_scmi: Add voltage domain management protocol support
dt-bindings: arm: Add support for SCMI Regulators
For sake of consistency, remove any residual naming based on _le
suffixes in SCMI sensors protocol, since little endianness is already
assumed across all of SCMI implementation and, as such, all currently
existent names do not explicitly state their endianness.
No functional change.
Link: https://lore.kernel.org/r/20201123162008.35814-1-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add SCMI voltage domain device name to the core list of supported protocol
devices so that it can be enumerated if the firmware supports it.
Link: https://lore.kernel.org/r/20201119191051.46363-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI v3.0 introduces voltage domain protocol which provides commands to:
- Discover the voltage levels supported by a domain
- Get the configuration and voltage level of a domain
- Set the configuration and voltage level of a domain
Let us add support for the same.
Link: https://lore.kernel.org/r/20201119191051.46363-2-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add support for new SCMI v3.0 Sensors extensions related to new sensors'
features, like multiple axis and update intervals, while keeping
compatibility with SCMI v2.0 features.
While at that, refactor and simplify all the internal helpers macros and
move struct scmi_sensor_info to use only non-fixed-size typing.
Link: https://lore.kernel.org/r/20201119174906.43862-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
destroy_workqueue is required before the return from scmi_notification_init
in case devm_kcalloc fails to allocate registered_protocols. Fix this by
simply moving registered_protocols allocation before alloc_workqueue.
Link: https://lore.kernel.org/r/20201110074221.41235-1-miaoqinglang@huawei.com
Fixes: bd31b24969 ("firmware: arm_scmi: Add notification dispatch and delivery")
Suggested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When more than a single SCMI device are present in the system, the
creation of the notification workqueue with the WQ_SYSFS flag will lead
to the following sysfs duplicate node warning:
sysfs: cannot create duplicate filename '/devices/virtual/workqueue/scmi_notify'
CPU: 0 PID: 20 Comm: kworker/0:1 Not tainted 5.9.0-gdf4dd84a3f7d #29
Hardware name: Broadcom STB (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
Backtrace:
show_stack + 0x20/0x24
dump_stack + 0xbc/0xe0
sysfs_warn_dup + 0x70/0x80
sysfs_create_dir_ns + 0x15c/0x1a4
kobject_add_internal + 0x140/0x4d0
kobject_add + 0xc8/0x138
device_add + 0x1dc/0xc20
device_register + 0x24/0x28
workqueue_sysfs_register + 0xe4/0x1f0
alloc_workqueue + 0x448/0x6ac
scmi_notification_init + 0x78/0x1dc
scmi_probe + 0x268/0x4fc
platform_drv_probe + 0x70/0xc8
really_probe + 0x184/0x728
driver_probe_device + 0xa4/0x278
__device_attach_driver + 0xe8/0x148
bus_for_each_drv + 0x108/0x158
__device_attach + 0x190/0x234
device_initial_probe + 0x1c/0x20
bus_probe_device + 0xdc/0xec
deferred_probe_work_func + 0xd4/0x11c
process_one_work + 0x420/0x8f0
worker_thread + 0x4fc/0x91c
kthread + 0x21c/0x22c
ret_from_fork + 0x14/0x20
kobject_add_internal failed for scmi_notify with -EEXIST, don't try to
register things with the same name in the same directory.
arm-scmi brcm_scmi@1: SCMI Notifications - Initialization Failed.
arm-scmi brcm_scmi@1: SCMI Notifications NOT available.
arm-scmi brcm_scmi@1: SCMI Protocol v1.0 'brcm-scmi:' Firmware version 0x1
Fix this by using dev_name(handle->dev) which guarantees that the name is
unique and this also helps correlate which notification workqueue corresponds
to which SCMI device instance.
Link: https://lore.kernel.org/r/20201014021737.287340-1-f.fainelli@gmail.com
Fixes: bd31b24969 ("firmware: arm_scmi: Add notification dispatch and delivery")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[sudeep.holla: trimmed backtrace to remove all unwanted hexcodes and timestamps]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When a protocol registers its events, the notification core takes care
to rescan the hashtable of pending event handlers and activate all the
possibly existent handlers referring to any of the events that are just
registered by the new protocol. When a pending handler becomes active
the core requests and enables the corresponding events in the SCMI
firmware.
If, for whatever reason, the enable fails, such invalid event handler
must be finally removed and freed. Let us ensure to use the
scmi_put_active_handler() helper which handles properly the needed
additional locking.
Failing to properly acquire all the needed mutexes exposes a race that
leads to the following splat being observed:
WARNING: CPU: 0 PID: 388 at lib/refcount.c:28 refcount_warn_saturate+0xf8/0x148
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development
Platform, BIOS EDK II Jun 30 2020
pstate: 40000005 (nZcv daif -PAN -UAO BTYPE=--)
pc : refcount_warn_saturate+0xf8/0x148
lr : refcount_warn_saturate+0xf8/0x148
Call trace:
refcount_warn_saturate+0xf8/0x148
scmi_put_handler_unlocked.isra.10+0x204/0x208
scmi_put_handler+0x50/0xa0
scmi_unregister_notifier+0x1bc/0x240
scmi_notify_tester_remove+0x4c/0x68 [dummy_scmi_consumer]
scmi_dev_remove+0x54/0x68
device_release_driver_internal+0x114/0x1e8
driver_detach+0x58/0xe8
bus_remove_driver+0x88/0xe0
driver_unregister+0x38/0x68
scmi_driver_unregister+0x1c/0x28
scmi_drv_exit+0x1c/0xae0 [dummy_scmi_consumer]
__arm64_sys_delete_module+0x1a4/0x268
el0_svc_common.constprop.3+0x94/0x178
do_el0_svc+0x2c/0x98
el0_sync_handler+0x148/0x1a8
el0_sync+0x158/0x180
Link: https://lore.kernel.org/r/20201013133109.49821-1-cristian.marussi@arm.com
Fixes: e7c215f358 ("firmware: arm_scmi: Add notification callbacks-registration")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Few commands provide the list of description partially and require
to be called consecutively until all the descriptors are fetched
completely. In such cases, we don't release the buffers and reuse
them for consecutive transmits.
However, currently we don't reset the Rx size which will be set as
per the response for the last transmit. This may result in incorrect
response size being interpretted as the firmware may repond with size
greater than the one set but we read only upto the size set by previous
response.
Let us reset the receive buffer size to max possible in such cases as
we don't know the exact size of the response.
Link: https://lore.kernel.org/r/20201012141746.32575-1-sudeep.holla@arm.com
Fixes: b6f20ff8bd ("firmware: arm_scmi: add common infrastructure and support for base protocol")
Reported-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SMC/HVC can transmit only one message at the time as the shared memory
needs to be protected and the calls are synchronous.
However, in order to allow multiple threads to send SCMI messages
simultaneously, we need a larger poll of memory.
Let us just use value of 20 to keep it in sync mailbox transport
implementation. Any other value must work perfectly.
Link: https://lore.kernel.org/r/20201008143722.21888-4-etienne.carriere@linaro.org
Fixes: 1dc6558062 ("firmware: arm_scmi: Add smc/hvc transport")
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[sudeep.holla: reworded the commit message to indicate the practicality]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The defination for ARCH_COLD_RESET is wrong. Let us fix it according to
the SCMI specification.
Link: https://lore.kernel.org/r/20201008143722.21888-5-etienne.carriere@linaro.org
Fixes: 95a15d80aa ("firmware: arm_scmi: Add RESET protocol in SCMI v2.0")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now, with all the plumbing in place to enable building scmi as a module
instead of built-in modules, let us enable the same.
Link: https://lore.kernel.org/r/20200907195046.56615-5-sudeep.holla@arm.com
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In preparation to enable building SCMI as a single module, let us move
the SCMI protocol registration call into the driver. This enables us
to also add unregistration of the SCMI protocols.
The main reason for this is to keep it simple instead of maintaining
it as separate modules and dealing with all possible initcall races
and deferred probe handling. We can move it as separate modules if
needed in future.
Link: https://lore.kernel.org/r/20200907195046.56615-4-sudeep.holla@arm.com
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In preparation to enable building scmi as a single module, let us move
the scmi bus {de-,}initialisation call into the driver.
The main reason for this is to keep it simple instead of maintaining
it as separate modules and dealing with all possible initcall races
and deferred probe handling. We can move it as separate modules if
needed in future.
Link: https://lore.kernel.org/r/20200907195046.56615-3-sudeep.holla@arm.com
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
scmi_mailbox is obtained from cinfo->transport_info and the first
call to mailbox_chan_free frees the channel and sets cinfo->transport_info
to NULL. Care is taken to check for non NULL smbox->chan but smbox can
itself be NULL. Fix it by checking for it without which, kernel crashes
with below NULL pointer dereference and eventually kernel panic.
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000038
Modules linked in: scmi_module(-)
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno
Development Platform, BIOS EDK II Sep 2 2020
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : mailbox_chan_free+0x2c/0x70 [scmi_module]
lr : idr_for_each+0x6c/0xf8
Call trace:
mailbox_chan_free+0x2c/0x70 [scmi_module]
idr_for_each+0x6c/0xf8
scmi_remove+0xa8/0xf0 [scmi_module]
platform_drv_remove+0x34/0x58
device_release_driver_internal+0x118/0x1f0
driver_detach+0x58/0xe8
bus_remove_driver+0x64/0xe0
driver_unregister+0x38/0x68
platform_driver_unregister+0x1c/0x28
scmi_driver_exit+0x38/0x44 [scmi_module]
---[ end trace 17bde19f50436de9 ]---
Kernel panic - not syncing: Fatal exception
SMP: stopping secondary CPUs
Kernel Offset: 0x1d0000 from 0xffff800010000000
PHYS_OFFSET: 0x80000000
CPU features: 0x0240022,25806004
Memory Limit: none
---[ end Kernel panic - not syncing: Fatal exception ]---
Link: https://lore.kernel.org/r/20200908112611.31515-1-sudeep.holla@arm.com
Fixes: 5c8a47a5a9 ("firmware: arm_scmi: Make scmi core independent of the transport type")
Cc: Cristian Marussi <cristian.marussi@arm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add SCMI device for system power protocol by just adding the name "syspower"
to the list of supported core protocol devices.
Link: https://lore.kernel.org/r/20200907174657.32466-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add bare protocol support for SCMI system power protocol as needed by
an OSPM agent: basic initialization and SYSTEM_POWER_STATE_NOTIFIER
core notification support.
No event-handling logic is attached to such notification..
Link: https://lore.kernel.org/r/20200907174657.32466-2-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Kbuild test robot reports the following sparse warning:
drivers/firmware/arm_scmi/clock.c:142:21:
sparse: Using plain integer as NULL pointer
Use NULL pointer instead of integer 0 for rate pointer and fix the
warning.
Link: https://lore.kernel.org/r/20200717140405.17905-1-sudeep.holla@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Event reports are used to convey information describing events to the
registered user-callbacks: they are necessarily derived from the underlying
raw SCMI events' messages but they are not meant to expose or directly
mirror any of those messages data layout, which belong to the protocol
layer.
Using fixed size types for report fields, mirroring messages structure,
is at odd with this: get rid of them using more generic, equivalent,
typing.
Substitute scmi_event_header fixed size fields with generic types too and
shuffle around fields definitions to minimize implicit padding while
adapting involved functions.
Link: https://lore.kernel.org/r/20200710133919.39792-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
gcc as well as clang now produce warnings for missing kerneldoc function
parameter.
Fix the following W=1 kernel build warning:
drivers/firmware/arm_scmi/smc.c:32:
warning: Function parameter or member 'shmem_lock' not described in 'scmi_smc'
Link: https://lore.kernel.org/r/20200709153155.22573-1-sudeep.holla@arm.com
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Instead of relying on the firmware to keep the clock rates sorted, let
us sort the list. This is not essential for clock layer but it helps
to find the min and max rates easily from the list.
Link: https://lore.kernel.org/r/20200709081705.46084-1-sudeep.holla@arm.com
Fixes: 5f6c6430e9 ("firmware: arm_scmi: add initial support for clock protocol")
Reported-and-tested-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Make SCMI base protocol register with the notification core.
Link: https://lore.kernel.org/r/20200701155348.52864-10-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Make SCMI power protocol register with the notification core.
Link: https://lore.kernel.org/r/20200701155348.52864-6-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Initialize and enable SCMI notifications core support during bus/driver
probe phase, so that protocols can start registering their supported
events during their initialization.
Link: https://lore.kernel.org/r/20200701155348.52864-5-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add the core SCMI notifications dispatch and delivery support logic
which is able to dispatch well-known received events from the Rx
interrupt handler to the dedicated deferred worker. From there, it will
deliver the events to the registered users' callbacks.
Dispatch and delivery support is just added here, still not enabled.
Link: https://lore.kernel.org/r/20200701155348.52864-4-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add the core SCMI notifications callbacks-registration support: allow
users to register their own callbacks against the desired events.
Whenever a registration request is issued against a still non existent
event, mark such request as pending for later processing, in order to
account for possible late initializations of SCMI Protocols associated
to loadable drivers.
Link: https://lore.kernel.org/r/20200701155348.52864-3-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add the core SCMI notifications protocol-registration support: allow
protocols to register their own set of supported events, during their
initialization phase. Notification core can track multiple platform
instances by their handles.
Link: https://lore.kernel.org/r/20200701155348.52864-2-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When, at probe time, an SCMI communication failure inhibits the capacity
to query power domains states, such domains should be skipped.
Registering partially initialized SCMI power domains with genpd will
causes kernel panic.
arm-scmi timed out in resp(caller: scmi_power_state_get+0xa4/0xd0)
scmi-power-domain scmi_dev.2: failed to get state for domain 9
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Mem abort info:
ESR = 0x96000006
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000009f3691000
[0000000000000000] pgd=00000009f1ca0003, p4d=00000009f1ca0003, pud=00000009f35ea003, pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
CPU: 2 PID: 381 Comm: bash Not tainted 5.8.0-rc1-00011-gebd118c2cca8 #2
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Jan 3 2020
Internal error: Oops: 96000006 [#1] PREEMPT SMP
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : of_genpd_add_provider_onecell+0x98/0x1f8
lr : of_genpd_add_provider_onecell+0x48/0x1f8
Call trace:
of_genpd_add_provider_onecell+0x98/0x1f8
scmi_pm_domain_probe+0x174/0x1e8
scmi_dev_probe+0x90/0xe0
really_probe+0xe4/0x448
driver_probe_device+0xfc/0x168
device_driver_attach+0x7c/0x88
bind_store+0xe8/0x128
drv_attr_store+0x2c/0x40
sysfs_kf_write+0x4c/0x60
kernfs_fop_write+0x114/0x230
__vfs_write+0x24/0x50
vfs_write+0xbc/0x1e0
ksys_write+0x70/0xf8
__arm64_sys_write+0x24/0x30
el0_svc_common.constprop.3+0x94/0x160
do_el0_svc+0x2c/0x98
el0_sync_handler+0x148/0x1a8
el0_sync+0x158/0x180
Do not register any power domain that failed to be queried with genpd.
Fixes: 898216c97e ("firmware: arm_scmi: add device power domain support using genpd")
Link: https://lore.kernel.org/r/20200619220330.12217-1-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit e5bfb21d98 ("firmware: smccc: Add HAVE_ARM_SMCCC_DISCOVERY to
identify SMCCC v1.1 and above") introduced new config option to identify
the availability of SMCCC discoverability of version and features
transparently hiding the indirect dependency on ARM_PSCI_FW.
Commit 5a897e3ab4 ("firmware: arm_scmi: fix psci dependency") just
worked around the build dependency making SCMI SMC/HVC transport depend
on ARM_PSCI_FW at the time. Since it really just relies on SMCCC directly
and not on ARM_PSCI_FW, let us move to use CONFIG_HAVE_ARM_SMCCC_DISCOVERY
instead of CONFIG_ARM_PSCI_FW.
Link: https://lore.kernel.org/r/20200625101937.51939-1-sudeep.holla@arm.com
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a new fast_switch_possible interface to the existing perf_ops to
export the information of whether or not fast_switch is possible for a
given device.
This can be used by the cpufreq driver and framework to choose proper
mechanism for frequency change.
Link: https://lore.kernel.org/r/20200617094332.8391-1-nicola.mazzucato@arm.com
Suggested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently the trace event 'scmi_xfer_end' reports the status of the
transfer using the unsigned status field read from the firmware which
may not be easy to interpret. It may also miss to emit any timeouts
that happen in the driver resulting in emitting garbage in the status
field in those scenarios.
Let us use signed integer so that error values are emitted out after
they are mapped from firmware error formats to standard linux error
codes. While at this, also include any timeouts in the driver itself.
Link: https://lore.kernel.org/r/20200609134503.55860-1-sudeep.holla@arm.com
Cc: Jim Quinlan <james.quinlan@broadcom.com>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When CONFIG_ARM_PSCI_FW is disabled but CONFIG_HAVE_ARM_SMCCC is enabled,
arm-scmi runs into a link failure:
arm-linux-gnueabi-ld: drivers/firmware/arm_scmi/smc.o: in function `smc_send_message':
smc.c:(.text+0x200): undefined reference to `arm_smccc_1_1_get_conduit'
Change from HAVE_ARM_SMCCC to ARM_PSCI_FW config dependency for now.
We rely on PSCI bindings anyways for the conduit and this should be
fine.
Link: https://lore.kernel.org/r/20200507144905.11397-1-sudeep.holla@arm.com
Fixes: 1dc6558062 ("firmware: arm_scmi: Add smc/hvc transport")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Upon reception of an unexpected bogus delayed response, clear the channel
and bail-out safely.
Link: https://lore.kernel.org/r/20200420152315.21008-5-cristian.marussi@arm.com
Fixes: 4d09852b6f ("firmware: arm_scmi: Add support for notifications message processing")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Clear channel properly when done processing a delayed response.
This will let the platform firmware know that the channel is now free to
use it for any new delayed response or notification.
Link: https://lore.kernel.org/r/20200420152315.21008-4-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
(sudeep.holla: Updated commit log to reflect that channel is now free for
platform to use)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When an unexpected response message is received we currently warn the user
and bail-out, ensure to also free the channel by invoking the transport
independent operation .clear_channel()
Link: https://lore.kernel.org/r/20200420152315.21008-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI transport operation .clear_notification() is indeed a generic method
to clear the channel in a transport dependent way, as such it could be a
useful helper also in other contexts.
Rename such method as .clear_channel(), renaming accordingly also its
already existent call-sites.
No functional change.
Link: https://lore.kernel.org/r/20200420152315.21008-2-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add the mechanisms to distinguish notifications from delayed responses
and command responses. Also add support to properly fetch notification
messages upon reception. Notifications processing does not continue any
further after the fetch phase.
Link: https://lore.kernel.org/r/20200327143438.5382-5-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[Reworked/renamed scmi_handle_xfer_delayed_resp()]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add common transport-layer methods to:
- fetch a notification instead of a response
- clear a pending notification
Add also all the needed support in mailbox/shmem transports.
Link: https://lore.kernel.org/r/20200327143438.5382-4-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add commands' enumerations and messages definitions for all existing
notify-enable commands across all protocols.
Link: https://lore.kernel.org/r/20200327143438.5382-3-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
With all the plumbing in place, let's just add the separate dedicated
receive buffers to handle notifications that can arrive asynchronously
from the platform firmware to OS.
Also add one check to see if the platform supports any receive channels
before allocating the receive buffers: since those buffers are optionally
supported though, the whole xfer initialization is also postponed to be
able to check for their existence in advance.
Link: https://lore.kernel.org/r/20200327143438.5382-2-cristian.marussi@arm.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[Changed parameters in __scmi_xfer_info_init()]
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The scmi protocol core driver checks for the channel availability
before evaluating the shmem property. If the individual protocols
don't have separate channel assigned to them, the channel alloted
for the BASE protocol is reused automatically.
Therefore there is no need to check for the shmem property in the
parent node if it is absent in the child protocol node.
Link: https://lore.kernel.org/r/20200327163654.13389-5-sudeep.holla@arm.com
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Instead of declaring the channel availabilty unconditionally, let us
check for the presence of "shmem" property and return the channel
availablity accordingly.
Link: https://lore.kernel.org/r/20200327163654.13389-4-sudeep.holla@arm.com
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The scmi protocol core driver check for non NULL mark_txdone before
invoking the same. There is no need to provide a empty stub. SMC/HVC
calls are synchronous and the call return indicates the completion.
Link: https://lore.kernel.org/r/20200327163654.13389-3-sudeep.holla@arm.com
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to support multiple SMC/HVC transport channels with associated
shared memory, it is better to maintain the mutex per channel instead of
existing global one.
Move the smc_mutex into the scmi_smc structure and also rename it to
shmem_lock which is more appropriate for it's use.
Link: https://lore.kernel.org/r/20200327163654.13389-2-sudeep.holla@arm.com
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Use the value of "arm,smc-id" property from the device tree as the first
argument for SMCCC call leaving all the other arguments as zero for now.
There is no Rx, only Tx because of smc/hvc not support Rx.
Link: https://lore.kernel.org/r/1583673879-20714-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[sudeep.holla: reworded commit log/subject and fixed !HAVE_ARM_SMCCC build]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Replace the zero-length member "opp" in scmi_msg_resp_perf_describe_levels
structure with flexible-array.
Link: https://lore.kernel.org/r/20200211231252.GA14830@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Replace the zero-length member "msg_payload" in scmi_shared_mem
structure with flexible-array.
Link: https://lore.kernel.org/r/20200211231045.GA13956@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[ rebased the change as files are moved around ]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SCMI specification is fairly independent of the transport protocol,
which can be a simple mailbox (already implemented) or anything else.
The current Linux implementation however is very much dependent on the
mailbox transport layer.
This patch makes the SCMI core code (driver.c) independent of the
mailbox transport layer and moves all mailbox related code to a new
file: mailbox.c and all struct shared_mem related code to a new file:
shmem.c.
We can now implement more transport protocols to transport SCMI
messages.
The transport protocols just need to provide struct scmi_transport_ops,
with its version of the callbacks to enable exchange of SCMI messages.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/8698a3cec199b8feab35c2339f02dc232bfd773b.1580448239.git.viresh.kumar@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SCMI transport layer communicates via mailboxes and shared memory with
firmware running on a microcontroller. It is platform specific how long it
takes to pass a SCMI message. The most sensitive requests are coming from
CPUFreq subsystem, which might be used by the scheduler.
Thus, there is a need to measure these delays and capture anomalies.
This change introduces trace events wrapped around transfer code.
According to Jim's suggestion a unique transfer_id is to distinguish
similar entries which might have the same message id, protocol id and
sequence. This is a case then there are some timeouts in transfers.
Suggested-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The scmi bus now supports adding multiple devices per protocol,
and since scmi_protocol_init is called for each scmi device created,
we must avoid allocating protocol private data and initialising the
protocol itself if it is already initialised.
In order to achieve the same, we can simple replace the idr pointer
from protocol initialisation function to a dummy function.
Suggested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to avoid querying the individual protocol versions multiple
time with more that one device created for each protocol, we can simple
store the copy in the protocol specific private data and use them whenever
required.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The scmi bus now has support to match the driver with devices not only
based on their protocol id but also based on their device name if one is
available. This was added to cater the need to support multiple devices
and drivers for the same protocol.
Let us add the name "genpd" to scmi_device_id table in the driver so
that in matches only with device with the same name and protocol id
SCMI_PROTOCOL_POWER.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. Using the same, let's add
the scmi firmware and protocol version attributes as well as vendor and
sub-vendor identifiers to sysfs.
It helps to identify the firmware details from the sysfs entries similar
to ARM SCPI implementation.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that scmi bus provides option to create named scmi device, let us
create the default devices with names. This will help to add names for
matching to respective drivers and eventually to add multiple devices
and drivers per protocol.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that the scmi bus supports adding multiple devices per protocol,
and since scmi_create_protocol_device calls scmi_mbox_chan_setup,
we must avoid allocating and initialising the mbox channel if it is
already initialised.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently only one scmi device is created for each protocol enumerated.
However, there is requirement to make use of some procotols by multiple
kernel subsystems/frameworks. One such example is SCMI PERFORMANCE
protocol which can be used by both cpufreq and devfreq drivers.
Similarly, SENSOR protocol may be used by hwmon and iio subsystems,
and POWER protocol may be used by genpd and regulator drivers.
In order to achieve that, let us extend the scmi bus to match based
not only protocol id but also the scmi device name if one is available.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
If device_register() fails, both put_device() and kfree() are called,
ending with a double free of the scmi_dev.
Calling kfree() is needed only when a failure happens between the
allocation of the scmi_dev and its registration, so move it to there
and remove it from the error flow.
Fixes: 46edb8d132 ("firmware: arm_scmi: provide the mandatory device release callback")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The logic to ring the scmi performance fastchannel ignores the
value read from the doorbell register in case of !CONFIG_64BIT.
This bug also shows up as warning with '-Wunused-but-set-variable' gcc
flag:
drivers/firmware/arm_scmi/perf.c: In function scmi_perf_fc_ring_db:
drivers/firmware/arm_scmi/perf.c:323:7: warning: variable val set but
not used [-Wunused-but-set-variable]
Fix the same by aligning the logic with CONFIG_64BIT as used in the
macro SCMI_PERF_FC_RING_DB().
Fixes: 823839571d ("firmware: arm_scmi: Make use SCMI v2.0 fastchannel for performance protocol")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMIv2.0 adds a new Reset Management Protocol to manage various reset
states a given device or domain can enter. Device(s) that can be
collectively reset through a common reset signal constitute a reset
domain for the firmware.
A reset domain can be reset autonomously or explicitly through assertion
and de-assertion of the signal. When autonomous reset is chosen, the
firmware is responsible for taking the necessary steps to reset the
domain and to subsequently bring it out of reset. When explicit reset is
chosen, the caller has to specifically assert and then de-assert the
reset signal by issuing two separate RESET commands.
Add the basic SCMI reset infrastructure that can be used by Linux
reset controller driver.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI v2.0 adds support for "FastChannel" which do not use a message
header as they are specialized for a single message.
Only PERFORMANCE_LIMITS_{SET,GET} and PERFORMANCE_LEVEL_{SET,GET}
commands are supported over fastchannels. As they are optional, they
need to be discovered by PERFORMANCE_DESCRIBE_FASTCHANNEL command.
Further {LIMIT,LEVEL}_SET commands can have optional doorbell support.
Add support for making use of these fastchannels.
Cc: Ionela Voinescu <Ionela.Voinescu@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Quentin Perret <Quentin.Perret@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI v2.0 adds support for "FastChannel", a lightweight unidirectional
channel that is dedicated to a single SCMI message type for controlling
a specific platform resource. They do not use a message header as they
are specialized for a single message.
Only PERFORMANCE_LIMITS_{SET,GET} and PERFORMANCE_LEVEL_{SET,GET}
commands are supported over fastchannels. As they are optional, they
need to be discovered by PERFORMANCE_DESCRIBE_FASTCHANNEL command.
Further {LIMIT,LEVEL}_SET commands can have optional doorbell support.
Add support for discovery of these fastchannels.
Cc: Ionela Voinescu <Ionela.Voinescu@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Quentin Perret <Quentin.Perret@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Instead of type-casting the {tx,rx}.buf all over the place while
accessing them to read/write __le{32,64} from/to the firmware, let's
use the existing {get,put}_unaligned_le{32,64} accessors to hide all
the type cast ugliness.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
CLOCK_PROTOCOL_ATTRIBUTES provides attributes to indicate the maximum
number of pending asynchronous clock rate changes supported by the
platform. If it's non-zero, then we should be able to use asynchronous
clock rate set for any clocks until the maximum limit is reached.
Tracking the current count of pending asynchronous clock set rate
requests, we can decide if the incoming/new request for clock set rate
can be handled asynchronously or not until the maximum limit is
reached.
Cc: linux-clk@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
CLOCK_PROTOCOL_ATTRIBUTES provides attributes to indicate the maximum
number of pending asynchronous clock rate changes supported by the
platform. If it's non-zero, then we should be able to use asynchronous
clock rate set for any clocks until the maximum limit is reached.
In order to add that support, let's drop the config flag passed to
clk_ops->rate_set and handle the asynchronous requests dynamically.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. We can read that flag and use asynchronous
reads for any sensors with that attribute set.
Let's use the new scmi_do_xfer_with_response to support asynchronous
sensor reads.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. Ideally we should be able to read that flag
and use asynchronous reads for any sensors with that attribute set.
In order to add that support, let's drop the async flag passed to
sensor_ops->reading_get and dynamically switch between sync and async
flags based on the attributes as provided by the firmware.
Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Messages that are sent to platform, also known as commands and can be:
1. Synchronous commands that block the channel until the requested work
has been completed. The platform responds to these commands over the
same channel and hence can't be used to send another command until the
previous command has completed.
2. Asynchronous commands on the other hand, the platform schedules the
requested work to complete later in time and returns almost immediately
freeing the channel for new commands. The response indicates the success
or failure in the ability to schedule the requested work. When the work
has completed, the platform sends an additional delayed response message.
Using the same transmit buffer used for sending the asynchronous command
even for the delayed response corresponding to it simplifies handling of
the delayed response. It's the caller of asynchronous command that is
responsible for allocating the completion flag that scmi driver can
complete to indicate the arrival of delayed response.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to identify the message type when a response arrives, we need
a mechanism to unpack the message header similar to packing. Let's
add one.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently we pre-allocate transmit buffers only and use the first free
slot in that pre-allocated buffer for transmitting any new message that
are generally originated from OS to the platform firmware.
Notifications or the delayed responses on the other hand are originated
from the platform firmware and consumes by the OS. It's better to have
separate and dedicated pre-allocated buffers to handle the notifications.
We can still use the transmit buffers for the delayed responses.
In addition, let's prepare existing scmi_xfer_{get,put} for acquiring
and releasing a slot to identify the right(tx/rx) buffers.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
With scmi_mbox_chan_setup enabled to identify and setup both Tx and Rx,
let's consolidate setting up of both the channels under the function
scmi_mbox_txrx_setup.
Since some platforms may opt not to support notifications or delayed
response, they may not need support for Rx. Hence Rx is optional and
failure of setting one up is not considered fatal.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The transmit(Tx) channels are specified as the first entry and the
receive(Rx) channels are the second entry as per the device tree
bindings. Since we currently just support Tx, index 0 is hardcoded at
all required callsites.
In order to prepare for adding Rx support, let's remove those hardcoded
index and add boolean parameter to identify Tx/Rx channels when setting
them up.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Re-shuffling few functions to keep definitions and their usages close.
This is also needed to avoid too many unnecessary forward declarations
while adding new features(delayed response and notifications).
Keeping this separate to avoid mixing up of these trivial change that
doesn't affect functionality into the ones that does.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Sometimes platfom may take too long to respond to the command and OS
might timeout before platform transfer the ownership of the shared
memory region to the OS with the response.
Since the mailbox channel associated with the channel is freed and new
commands are dispatch on the same channel, OS needs to wait until it
gets back the ownership. If not, either OS may end up overwriting the
platform response for the last command(which is fine as OS timed out
that command) or platform might overwrite the payload for the next
command with the response for the old.
The latter is problematic as platform may end up interpretting the
response as the payload. In order to avoid such race, let's wait until
the OS gets back the ownership before we prepare the shared memory with
the payload for the next command.
Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In preparation to adding support for other two types of messages that
SCMI specification mentions, let's replace the term 'command' with the
correct term 'message'.
As per the specification the messages are of 3 types:
commands(synchronous or asynchronous), delayed responses and notifications.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
While adding new comments found couple of typos that are better fixed.
s/informfation/information/
s/statues/status/
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
scmi_xfer_get_init ensures both transmit and receive buffer lengths are
within the maximum limits. If receive buffer length is not supplied by
the caller, it's set to the maximum limit value. Receive buffer length
is never modified after that. So there's no need for the extra check
when receive transmit completion for a command essage.
Further, if the response header length is greater than the prescribed
receive buffer length, the response buffer is truncated to the latter.
Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Looks like more code developed during the draft versions of the
specification slipped through and they don't match the final
released version. This seem to have happened only with sensor
protocol.
Renaming few command and function names here to match exactly with
the released version of SCMI specification for ease of maintenance.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
This patch corrects the SPDX License Identifier style
in header file related to Firmware Drivers for ARM SCMI
Message Protocol.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Correction to ARM document ID referred in SCMI protocol binding
2. Fix to correct bitfield definitions for SENSOR_DESC attributes which
otherwise will calculate sensor values on wrong scale
3. Adds the missing rate_discrete flag setting so that discrete clocks
are handled correctly. Without this fix it assumes continuous range
which is incorrect
4. Adds support to read and scale the sensor values based on the factor
read from the firmware
-----BEGIN PGP SIGNATURE-----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=RZCT
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
ARM SCMI updates/fixes for v5.3
1. Correction to ARM document ID referred in SCMI protocol binding
2. Fix to correct bitfield definitions for SENSOR_DESC attributes which
otherwise will calculate sensor values on wrong scale
3. Adds the missing rate_discrete flag setting so that discrete clocks
are handled correctly. Without this fix it assumes continuous range
which is incorrect
4. Adds support to read and scale the sensor values based on the factor
read from the firmware
* tag 'scmi-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: scmi: Scale values to target desired HWMON units
firmware: arm_scmi: fetch and store sensor scale
firmware: arm_scmi: update rate_discrete in clock_describe_rates_get
firmware: arm_scmi: fix bitfield definitions for SENSOR_DESC attributes
dt-bindings: arm: fix the document ID for SCMI protocol documentation
Signed-off-by: Olof Johansson <olof@lixom.net>
In preparation for dealing with scales within the SCMI HWMON driver,
fetch and store the sensor unit scale into the scmi_sensor_info
structure. In order to simplify computations for upper layer, take care
of sign extending the scale to a full 8-bit signed value.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[sudeep.holla: update bitfield values as per specification]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The boolean rate_discrete needs to be assigned to clk->rate_discrete,
so that clock driver can distinguish between the continuous range and
discrete rates. It uses this in scmi_clk_round_rate could get the
rounded value if it's a continuous range.
Fixes: 5f6c6430e9 ("firmware: arm_scmi: add initial support for clock protocol")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[sudeep.holla: updated commit message]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
As per the SCMI specification the bitfields for SENSOR_DESC attributes
are as follows:
attributes_low [7:0] Number of trip points supported
attributes_high [15:11] The power-of-10 multiplier in 2's-complement
format that is applied to the sensor units
Looks like the code developed during the draft versions of the
specification slipped through and are wrong with respect to final
released version. Fix them by adjusting the bitfields appropriately.
Fixes: 5179c523c1 ("firmware: arm_scmi: add initial support for sensor protocol")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device can return NULL if no matching device is found though
it's highly unlikely to happen in scmi_probe as it's called only if
a valid match is found.
However we can use of_device_get_match_data() instead of
of_match_device()->data to handle NULL pointer checks and return -EINVAL
in such a scenario.
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
of_parse_phandle_with_args() requires the caller to call of_node_put() on
the returned args->np pointer. Otherwise the reference count will remain
incremented.
However, in this case, since we don't actually use the returned pointer,
we can simply pass in NULL.
Fixes: aa4f886f38 ("firmware: arm_scmi: add basic driver infrastructure for SCMI")
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The device/driver model clearly mandates that bus driver that discover
and allocate the device must set the release callback. This callback
will be used to free the device after all references have gone away.
scmi bus driver is missing the obvious callback which will result in
the following warning if the device is unregistered:
Device 'scmi_dev.1' does not have a release() function, it is broken and
must be fixed. See Documentation/kobject.txt.
WARNING at drivers/base/core.c:922 device_release+0x8c/0xa0
Hardware name: ARM LTD Juno Development Platform BIOS EDK II Jan 21 2019
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : device_release+0x8c/0xa0
lr : device_release+0x8c/0xa0
Call trace:
device_release+0x8c/0xa0
kobject_put+0x8c/0x208
device_unregister+0x30/0x78
scmi_device_destroy+0x28/0x50
scmi_probe+0x354/0x5b0
platform_drv_probe+0x58/0xa8
really_probe+0x2c4/0x3e8
driver_probe_device+0x12c/0x148
__device_attach_driver+0xac/0x150
bus_for_each_drv+0x78/0xd8
__device_attach+0xe0/0x168
device_initial_probe+0x24/0x30
bus_probe_device+0xa0/0xa8
deferred_probe_work_func+0x8c/0xe0
process_one_work+0x1f0/0x478
worker_thread+0x22c/0x450
kthread+0x134/0x138
ret_from_fork+0x10/0x1c
---[ end trace 420bdb7f6af50937 ]---
Fix the issue by providing scmi_device_release callback. We have
everything required for device release already in scmi_device_destroy,
so we just need to move freeing of the device to scmi_device_release.
Fixes: 933c504424 ("firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SCMI protocol can be used to get power estimates from firmware
corresponding to each performance state of a device. Although these power
costs are already managed by the SCMI firmware driver, they are not
exposed to any external subsystem yet.
Fix this by adding a new get_power() interface to the exisiting perf_ops
defined for the SCMI protocol.
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Replace all the memcpy() for copying name strings from the firmware with
strlcpy() to make sure we are bounded by the source buffer size and we
also always have NULL-terminated strings.
This is needed to avoid out of bounds accesses if the firmware returns
a non-terminated string.
Reported-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Firmware can provide zero as values for sustained performance level and
corresponding sustained frequency in kHz in order to hide the actual
frequencies and provide only abstract values. It may endup with divide
by zero scenario resulting in kernel panic.
Let's set the multiplication factor to one if either one or both of them
(sustained_perf_level and sustained_freq) are set to zero.
Fixes: a9e3fbfaa0 ("firmware: arm_scmi: add initial support for performance protocol")
Reported-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The "pi->dom_info" buffer is allocated in init() and it can't be NULL
here. These tests are sort of weird as well because if "pi->dom_info"
was NULL but "domain" was non-zero then it would lead to an Oops.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This branch contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for several SoCs.
- Tegra memory controller reset improvements
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlsfB94PHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3k2IP/i9T71QoanZ3k6o/d+YUqmTuUiA+EJWFANry
8KSjBKmYDON/GLgRCiNZR8P0NZ3d1LgFk5gZDdhMrOtoGtd8k8q0KyqLxjKAWHt6
opSrGucmE1gy9FvJdUkK+y148vM+Ea4SXRVOZxbLV5qm3inPwnopJjgKAfnhIn4X
QmkSca90CyEc3kPdBdfMeAKL+7SRb4mbFHAXXVE7QiWvjrEjUkvtNVTazf5Nroc4
PbI97zSFrmSFO4ZK0jZHCd4R2xhsJwzDQ/UKHC9C9/IdFMLfnJ7dxIf97QYn41Kl
H46FneMZZZ1FibN+Mj5hC/tByE8FrMtWh636z031s6kkamSqLiBAZFlGpHABxQJs
3tN1vBP40R7hzm76yQAC4Uopr5xOtmLr6KBMBBRr+Axf9jHMS4m/WP1chwZFpFjI
Awxc0VCjBUm+haHvK85J4eHrzbWPjG+8aV5Ar5DHVo8et3MzCdX0ycoDeUT787qc
qzEcCjGPbXHBR1aXUX8stRW5x8zoGH/4IUYMo5IGadiFuXSna6ERG9IHq3fAU5Fp
ZzNNKedtodn9NoMr3NJJk1ndyrUr0lpXwlVqFeksRTa+INk2FHKd0cQfxwV33kS9
wHXw+v323uxa3Tz2TXKS7PavY5yr6fZ0dLC2+xEDqHq6bsLxo1DnBEnaola+Jg+u
9hKEuSff
=xs+f
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for
several SoCs.
- Tegra memory controller reset improvements"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (59 commits)
ARM: tegra: fix compile-testing PCI host driver
soc: rockchip: power-domain: add power domain support for px30
dt-bindings: power: add binding for px30 power domains
dt-bindings: power: add PX30 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3228
dt-bindings: power: add binding for rk3228 power domains
dt-bindings: power: add RK3228 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3128
dt-bindings: power: add binding for rk3128 power domains
dt-bindings: power: add RK3128 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3036
dt-bindings: power: add binding for rk3036 power domains
dt-bindings: power: add RK3036 SoCs header for power-domain
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
soc: mediatek: remove unneeded semicolon
soc: mediatek: add a fixed wait for SRAM stable
soc: mediatek: introduce a CAPS flag for scp_domain_data
soc: mediatek: reuse regmap_read_poll_timeout helpers
...
This contains all of the trivial review comments that were not
addressed as the series was already queued up for v4.17 and were not
critical to go as fixes.
They generally just improve code readability, fix kernel-docs, remove
unused/unnecessary code, follow standard function naming and simplifies
certain exit paths.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OzDu
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
SCMI cleanups for v4.18
This contains all of the trivial review comments that were not
addressed as the series was already queued up for v4.17 and were not
critical to go as fixes.
They generally just improve code readability, fix kernel-docs, remove
unused/unnecessary code, follow standard function naming and simplifies
certain exit paths.
* tag 'scmi-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: simplify exit path by returning on error
firmware: arm_scmi: improve exit paths and code readability
firmware: arm_scmi: remove unnecessary bitmap_zero
firmware: arm_scmi: drop unused `con_priv` structure member
firmware: arm_scmi: rename scmi_xfer_{init,get,put}
firmware: arm_scmi: rename get_transition_latency and add_opps_to_device
firmware: arm_scmi: fix kernel-docs documentation
firmware: arm_scmi: improve code readability using bitfield accessor macros
Signed-off-by: Olof Johansson <olof@lixom.net>
A single patch to ensure that the scmi device is not used for setting up
scmi handle after it's freed(fixes use after free).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UOAO
-----END PGP SIGNATURE-----
Merge tag 'scmi-fixes-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
SCMI fix for v4.17
A single patch to ensure that the scmi device is not used for setting up
scmi handle after it's freed(fixes use after free).
* tag 'scmi-fixes-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Use after free in scmi_create_protocol_device()
Signed-off-by: Olof Johansson <olof@lixom.net>
Yet another nasty indentation left out during code restructuring. It's
must simpler to return on error instead of having unnecessary indentation.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The existing code intends the good path to reduce the code which is so
uncommon. It's obvious to have more readable code with a goto used for
the error path. This patch adds more appropriate error paths and makes
code more readable. It also moves a error logging outside the scope of
locking.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
kcalloc zeros the memory and it's totally unnecessary to zero the bitmap
again using bitmap_zero. This patch just drops the unnecessary use of
the bitmap_zero in the context.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Initially con_priv was supposedly used for transport specific data when
the SCMI driver had an abstraction to communicate with different mailbox
controllers. But after some discussions, the idea was dropped but this
variable slipped through the cracks.
This patch gets rid of this unused variable.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Just after the initial patches were queued, Jonathan Cameron mentioned
that scmi_one_xfer_{get_put} were not very clear and suggested to use
scmi_xfer_{alloc,free}. While I agree to some extent, the reason not to
have alloc/free as these are preallocated buffers and these functions
just returns a reference to free slot in that preallocated array.
However it was agreed to drop "_one" as it's implicit that we are always
dealing with one slot anyways.
This patch updates the name accordingly dropping "_one" in both {get,put}
functions. Also scmi_one_xfer_init is renamed as scmi_xfer_get_init to
reflect the fact that it gets the free slots and then initialise it.
Reported-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Most of the scmi code follows the suggestion from Greg KH on a totally
different thread[0] to have the subsystem name first, followed by the
noun and finally the verb with couple of these exceptions.
This patch fixes them so that all the functions names are aligned to
that practice.
[0] https://www.spinics.net/lists/arm-kernel/msg583673.html
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
There are few missing descriptions for function parameters and structure
members along with certain instances where excessive function parameters
or structure members are described.
This patch fixes all of those warnings.
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
By using FIELD_{FIT,GET,PREP} and GENMASK macro accessors we can avoid
some clumpsy custom shifting and masking macros and also improve the
code better readability.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
We need to return here instead of setting up the freed sdev device as a
transport.
Fixes: 907b6d1491 ("firmware: arm_scmi: add per-protocol channels support using idr objects")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The null check on clk->name is redundant since name is a char array
and can never be null, so the check is always true. Remove it.
Detected by CoverityScan, CID#1466117 ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
gcc-5.3 and earlier warns that rate_discrete maybe-uninitialized
../drivers/firmware/arm_scmi/clock.c:185:5: warning: 'rate_discrete'
may be used uninitialized in this function [-Wmaybe-uninitialized]
if (rate_discrete)
^
../drivers/firmware/arm_scmi/clock.c:128:7: note:
'rate_discrete' was declared here
bool rate_discrete;
^
This patch fixing the warning by initialising rate_discrete and also using
goto label for the error path.
Fixes: 5f6c6430e9 ("firmware: arm_scmi: add initial support for clock protocol")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
[sudeep.holla: added one line description to the commit message]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch hooks up the support for device power domain provided by
SCMI using the Linux generic power domain infrastructure.
Cc: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to maintain the channel information per protocol, we need
some sort of list or hashtable to hold all this information. IDR
provides sparse array mapping of small integer ID numbers onto arbitrary
pointers. In this case the arbitrary pointers can be pointers to the
channel information.
This patch adds support for per-protocol channels using those idr
objects.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to support per-protocol channels if available, we need to
factor out all the mailbox channel information(Tx/Rx payload and
channel handle) out of the main SCMI instance information structure.
This patch refactors the existing channel information into a separate
chan_info structure.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to implement fast CPU DVFS switching, we need to perform all
DVFS operations atomically. Since SCMI transfer already provide option
to choose between pooling vs interrupt driven(default), we can opt for
polling based transfers for set,get performance domain operations.
This patch adds option to choose between polling vs interrupt driven
SCMI transfers for set,get performance level operations.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
It would be useful to have options to perform some SCMI transfers
atomically by polling for the completion flag instead of interrupt
driven. The SCMI specification has option to disable the interrupt and
poll for the completion flag in the shared memory.
This patch adds support for polling based SCMI transfers using that
option. This might be used for uninterrupted/atomic DVFS operations
from the scheduler context.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that we have basic support for all the protocols in the
specification, let's probe them individually and initialise them.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The sensor protocol provides functions to manage platform sensors, and
provides the commands to describe the protocol version and the various
attribute flags. It also provides commands to discover various sensors
implemented and managed by the platform, read any sensor synchronously
or asynchronously as allowed by the platform, program sensor attributes
and/or configurations, if applicable.
This patch adds support for most of the above features.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The power protocol is intended for management of power states of various
power domains. The power domain management protocol provides commands to
describe the protocol version, discover the implementation specific
attributes, set and get the power state of a domain.
This patch adds support for the above mention features of the protocol.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
--
drivers/firmware/arm_scmi/Makefile | 2 +-
drivers/firmware/arm_scmi/power.c | 242 +++++++++++++++++++++++++++++++++++++
include/linux/scmi_protocol.h | 28 +++++
3 files changed, 271 insertions(+), 1 deletion(-)
create mode 100644 drivers/firmware/arm_scmi/power.c
The clock protocol is intended for management of clocks. It is used to
enable or disable clocks, and to set and get the clock rates. This
protocol provides commands to describe the protocol version, discover
various implementation specific attributes, describe a clock, enable
and disable a clock and get/set the rate of the clock synchronously or
asynchronously.
This patch adds initial support for the clock protocol.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The performance protocol is intended for the performance management of
group(s) of device(s) that run in the same performance domain. It
includes even the CPUs. A performance domain is defined by a set of
devices that always have to run at the same performance level.
For example, a set of CPUs that share a voltage domain, and have a
common frequency control, is said to be in the same performance domain.
The commands in this protocol provide functionality to describe the
protocol version, describe various attribute flags, set and get the
performance level of a domain. It also supports discovery of the list
of performance levels supported by a performance domain, and the
properties of each performance level.
This patch adds basic support for the performance protocol.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SCMI specification encompasses various protocols. However, not every
protocol has to be present on a given platform/implementation as not
every protocol is relevant for it.
Furthermore, the platform chooses which protocols it exposes to a given
agent. The only protocol that must be implemented is the base protocol.
The base protocol is used by an agent to discover which protocols are
available to it.
In order to enumerate the discovered implemented protocols, this patch
adds support for a separate scmi protocol bus. It also adds mechanism to
register support for different protocols.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The base protocol describes the properties of the implementation and
provide generic error management. The base protocol provides commands
to describe protocol version, discover implementation specific
attributes and vendor/sub-vendor identification, list of protocols
implemented and the various agents are in the system including OSPM
and the platform. It also supports registering for notifications of
platform errors.
This protocol is mandatory. This patch adds support for the same along
with some basic infrastructure to add support for other protocols.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
