Add the pmbus driver for TEXAS tps546d24 Buck Converter.
The vout mode of tps546d24 supported relative data format,
which is not supported by the PMBus core.
Signed-off-by: Duke Du <dukedu83@gmail.com>
Link: https://lore.kernel.org/r/1662951668-9849-1-git-send-email-Duke.Du@quantatw.com
[groeck: Add __maybe_unused to tps546d24_of_match declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware
sensors of the Aquacomputer High Flow Next flow sensor, which
communicates through a proprietary USB HID protocol.
The High Flow Next exposes +5V voltages, water quality, conductivity
and flow readings. A temperature sensor can be connected to it, in
which case it provides its reading and an estimation of the
dissipated/absorbed power in the liquid cooling loop.
Additionally, serial number and firmware version are exposed through
debugfs.
Registry offsets were discovered and tested by users on Github [1] [2].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/8
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/34
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220907100739.806571-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX31790 has a tach input enable bit in each fan's configuration
register. This is only enabled by the driver if RPM mode is selected,
but the driver doesn't provide a way to independently enable tachometer
input regardless of the regulator mode.
By adding the fanN_enable sysfs files, we can decouple the tach input
from the regulator mode. Also update the documentation.
Signed-off-by: Justin Ledford <justinledford@google.com>
Link: https://lore.kernel.org/r/20220829195930.2521755-1-justinledford@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add reporting if the PSU is running in single or multi rail mode via
ocpmode debugfs entry. Also update the documentation and driver comments
accordingly.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YvS9PZKr0xqFqJny@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading virtual temperature sensors for the D5 Next, Octo,
Quadro and Farbwerk 360.
Virtual temperature sensors are written to the device by the user, pulling
from an arbitrary value source. Writing to them is not yet reverse
engineered, so the only way to set them for now is to use the official
software.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220817121441.112198-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver utilises a WMI interface found in AMD 500 series ASUS boards,
to read EC registers. But it turned out that ASUS abandoned the
interface, as it disappeared from Intel 600 series boards. Additionally,
the WMI interface was incredibly slow. Therefore this driver was deprecated
in favor of the asus_ec_sensors driver, which supports more boards, more
sensors, and is faster.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
earth-shaking:
- More Chinese translations, and an update to the Italian translations.
The Japanese, Korean, and traditional Chinese translations are
more-or-less unmaintained at this point, instead.
- Some build-system performance improvements.
- The removal of the archaic submitting-drivers.rst document, with the
movement of what useful material that remained into other docs.
- Improvements to sphinx-pre-install to, hopefully, give more useful
suggestions.
- A number of build-warning fixes
Plus the usual collection of typo fixes, updates, and more.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmLn9OwPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YtrwIAJNZoDYJJIRuVHnFkAn5EJ4b/chnR1dSTBtn
WdE/1zdAlMBWVlEGO48VZybph9Sk0v+cUGf+yviDgASQrfOhRRTkg/0u6XaBAYO0
+C2D1QDd9DggGgajxsfJfTdD3IuB78mGmCQvP17XIJW+NK1CK9rXZBnj6WC5/HJw
PCHzeeVreBxOS3W9GelMYa6vjVl7dv81x4DPllnsgU2AMk0/Ce0MVjeIZ695sOeP
Ki6jZgC2GsgFSK5kBC35OiDe5q+fDzlLfek34EUCn4SIbMALSUYWO1db122w5Pme
Ej0+UTBhD19WH1uB/rcVKnVWugi7UEUJexZsao+nC7UrdIVtYq0=
=83BG
-----END PGP SIGNATURE-----
Merge tag 'docs-6.0' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This was a moderately busy cycle for documentation, but nothing
all that earth-shaking:
- More Chinese translations, and an update to the Italian
translations.
The Japanese, Korean, and traditional Chinese translations
are more-or-less unmaintained at this point, instead.
- Some build-system performance improvements.
- The removal of the archaic submitting-drivers.rst document,
with the movement of what useful material that remained into
other docs.
- Improvements to sphinx-pre-install to, hopefully, give more
useful suggestions.
- A number of build-warning fixes
Plus the usual collection of typo fixes, updates, and more"
* tag 'docs-6.0' of git://git.lwn.net/linux: (92 commits)
docs: efi-stub: Fix paths for x86 / arm stubs
Docs/zh_CN: Update the translation of sched-stats to 5.19-rc8
Docs/zh_CN: Update the translation of pci to 5.19-rc8
Docs/zh_CN: Update the translation of pci-iov-howto to 5.19-rc8
Docs/zh_CN: Update the translation of usage to 5.19-rc8
Docs/zh_CN: Update the translation of testing-overview to 5.19-rc8
Docs/zh_CN: Update the translation of sparse to 5.19-rc8
Docs/zh_CN: Update the translation of kasan to 5.19-rc8
Docs/zh_CN: Update the translation of iio_configfs to 5.19-rc8
doc:it_IT: align Italian documentation
docs: Remove spurious tag from admin-guide/mm/overcommit-accounting.rst
Documentation: process: Update email client instructions for Thunderbird
docs: ABI: correct QEMU fw_cfg spec path
doc/zh_CN: remove submitting-driver reference from docs
docs: zh_TW: align to submitting-drivers removal
docs: zh_CN: align to submitting-drivers removal
docs: ko_KR: howto: remove reference to removed submitting-drivers
docs: ja_JP: howto: remove reference to removed submitting-drivers
docs: it_IT: align to submitting-drivers removal
docs: process: remove outdated submitting-drivers.rst
...
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Quadro fan controller, which communicates
through a proprietary USB HID protocol. Implemented by Jack Doan [1].
Four temperature sensors and PWM controllable fans are available. The
liquid flow sensor is also exposed, implemented by Leonard Anderweit [2].
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/5
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/9
Originally-from: Jack Doan <me@jackdoan.com>
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220727100606.9328-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Notify users of this driver that each pwmX
attribute controls fan number X, meaning that
probing of pwm channels is unnecessary.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220727083004.5684-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 31b24bee33 ("docs: add a warning to submitting-drivers.rst")
in October 2016 already warns "This (...) should maybe just be deleted,
but I'm not quite ready to do that yet".
Maybe, six years ago, we were not ready but let us remove old content
for the better now and structure and maintain less content in the kernel
documentation with a better result.
Drop this already outdated document and adjust all textual references.
Here is an argument why deleting the content will not remove any useful
information to the existing kernel documentation, individually broken down
for each section.
Section "Allocating Device Numbers" refers to https://www.lanana.org/, and
then refers to Documentation/admin-guide/devices.rst.
However, the devices.rst clearly states:
"The version of this document at lanana.org is no longer maintained."
Everything needed for submitting drivers is already stated in devices.rst
and the reference to https://www.lanana.org/ is outdated, and should be
just deleted.
Section "Who To Submit Drivers To" is all about Linux 2.0 - 2.6, before
the new release version scheme; the mentioned developers are still around,
but actually not the first developers to contact anymore.
Section "What Criteria Determine Acceptance" has a few bullet points:
Licensing and Copyright is well-covered in process/kernel-license.rst.
Interfaces, Code, Portability, Clarity state some obvious things about
ensuring kernel code quality.
Control suggests to add a MAINTAINERS entry, which is already mentioned in
6.Followthrough.rst: "... added yourself to the MAINTAINERS file..."
PM support states a bit about implementing and testing power management of
a driver, it remains an open question where to place that in the process
documents. Driver developers interested in power management will find the
corresponding part on power management in the kernel documentation anyway.
In section "What Criteria Do Not Determine Acceptance", the points Vendor
and Author states something basic consequence of the kernel being an
open-source community software development. Probably no need to mention it
nowadays.
Section "Resources" lists resources that are also mentioned elsewhere more
central.
- Linux kernel tree and mailing list is mentioned in many places.
- https://lwn.net/Kernel/LDD3/ is mentioned in
Documentation/process/kernel-docs.rst.
- https://lwn.net/ is mentioned in:
- Documentation/process/8.Conclusion.rst
- Documentation/process/kernel-docs.rst
- https://kernelnewbies.org/ is mentioned in:
- Documentation/process/8.Conclusion.rst
- Documentation/process/kernel-docs.rst
- http://www.linux-usb.org/ is mentioned in
Documentation/driver-api/usb/usb.rst
- https://landley.net/kdocs/ols/2002/ols2002-pages-545-555.pdf
is mentioned in Documentation/process/kernel-docs.rst
- https://kernelnewbies.org/KernelJanitors is mentioned in
Documentation/process/howto.rst
- https://git-scm.com/ is mentioned in
- Documentation/process/2.Process.rst
- Documentation/process/7.AdvancedTopics.rst
- Documentation/process/howto.rst
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220704122537.3407-7-lukas.bulwahn@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add definitions for ROG MAXIMUS XI HERO and ROG MAXIMUS XI HERO (WI-FI)
boards.
Signed-off-by: Michael Carns <mike@carns.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220627225437.87462-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Analog Devices LT7182S Dual Channel 6A, 20V PolyPhase
Step-Down Silent Switcher with Digital Power System Management.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID
registers as well as 11 bit external temperature resolution.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet
error checking). Similar to NCT72 and NCT214, PEC support is undocumented.
Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary
chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when
reading those registers. The value for the chip revision register is not
documented but was observed to be 0xca. Use that information to improve
chip detection accuracy.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full
PEC (packet error checking) support. PEC support is undocumented.
Both chips support the undocumented secondary chip and manufacturer
ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this
information to improve the accuracy of chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6690 is all but identical to MAX6654. Revision 1 of its
datasheet lists the same chip ID as MAX6654, and a chip labeled
MAX6654 was found to have the chip ID listed as MAX6690 chip ID
in Revision 2 of its datasheet.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two
external temperature sensors, similar to MAX6695/6696. They support an
extended temperature range similar to ADT7461. Registers for the second
external channel can be accessed directly or by using the same method as
used by MAX6695/6696. For simplicity, the access method implemented for
MAX6695/6696 is used.
The chips support PEC (packet error checking). Set the PEC feature flag
and let the user decide if it should be enabled or not (it is by default
disabled).
Even though it is only documented for ADT7483, all three chips support a
secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f.
Use the contents of those registers register for improved chip detection
accuracy. Add the same check to the ADT7461A detection code since this chip
also supports the same (undocumented) registers.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike MAX6646/MAX6647/MAX6649, MAX6648 and MAX6692 only support
a temperature range of 0..127 degrees C. Separate support for the
two sets of chips to be able to support maximum temperature ranges
correctly for all chips. Introduce new feature flag to indicate
temperature support up to 255 degrees C.
Since the chips are almost identical except for the supported temperature
range, automatic chip detection is limited. Effectively this means that
MAX6648 may be mis-detected as MAX6649 when auto-detected, but there is
nothing we can do about that.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Revision 0 of the ADT7461 datasheet suggests that the chip supports PEC
(packet error checking). This information is gone in later versions of the
datasheet. Experiments show that PEC support on ADT7461 is similar to PEC
support in ADM1032, ie it is only supported for read operations. Add
support for it to the driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PEC (packet error checking) support for ADM1032 is currently only enabled
if the chip was auto-detected, but not if a chip is instantiated
explicitly. Always enable PEC support by introducing a chip feature flag
indicating partial PEC support. Also, for consistency, disable PEC support
by default to match existing functionality if the chip was not auto-
detected.
At the same time, introduce generic support for PEC with a separate feature
flag. This will be used when support for chips with full PEC functionality
is added.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enabling and disabling PEC for PMBus devices is currently only supported
with a debugfs attribute, which requires debugfs to be enabled and is
thus less than perfect. Take the lm90 driver as example and add a 'pec'
attribute to the I2C device if both the I2C adapter and the PMBus device
support it. Remove the now obsolete 'pec' attribute from debugfs.
Cc: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Various attempts were made recently to "convert" the old
hwmon_device_register() API to devm_hwmon_device_register_with_info()
by just changing the function name without actually converting the
driver. Prevent this from happening by making the 'chip' parameter of
devm_hwmon_device_register_with_info() mandatory.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds support for the ROG STRIX X570-E GAMING WIFI II board and
simplifies formatting for the list of supported models.
Signed-off-by: Debabrata Banerjee <dbavatar@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220505073351.123753-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another MAX16602 chip support to MAX16601 driver
Tested with MAX16602 works as expected.
Signed-off-by: Atif Ofluoglu <atif.ofluoglu@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware
temperature sensors of the Aquacomputer Farbwerk RGB controller, which
communicates through a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
Also, add Jack Doan to MAINTAINERS for this driver.
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/YmTcrq8Gzel0zYYD@jackdesk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When adding the Inspiron 3505 to the fan type blacklist,
the Documentation was not updated to mention the firmware
bug on this machine.
Fix that.
Fixes: 6ba463edcc (hwmon: (dell-smm) Add Inspiron 3505 to fan type blacklist)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220424154824.9396-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Until now, only the temperature sensors where exported thru
the thermal subsystem. Export the fans as "dell-smm-fan[1-3]" too
to make them available as cooling devices.
Also update Documentation and fix a minor issue with the alphabetic
ordering of the includes.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220410163935.7840-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
More and more drivers will check for bad characters in the hwmon name
and all are using the same code snippet. Consolidate that code by adding
a new hwmon_sanitize_name() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220405092452.4033674-2-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Octo fan controller, which communicates
through a proprietary USB HID protocol.
Four temperature sensors and eight PWM controllable fans are available.
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220404134212.9690-1-savicaleksa83@gmail.com
[groeck: Add missing "select CRC16"]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
- Add support for Maxim MAX77714 PMIC
- Remove Drivers
- Remove support for ST-Ericsson AB8500 DebugFS
- New Device Support
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
- New Functionality
- Add support for Reboot to Rockchip RK808
- Fix-ups
- Device Tree changes (inc. YAML conversion); silergy,sy7636a, maxim,max77843,
google,cros-ec, maxim,max14577, maxim,max77802,
maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576
-----BEGIN PGP SIGNATURE-----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=1xnI
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Maxim MAX77714 PMIC
Removed Drivers:
- Remove support for ST-Ericsson AB8500 DebugFS
New Device Support:
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
New Functionality:
- Add support for Reboot to Rockchip RK808
Fix-ups:
- Device Tree changes (includcing YAML conversion) for
silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577,
maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576"
* tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible
mfd: bd9576: fix typos in comments
mfd: Use platform_get_irq() to get the interrupt
mfd: db8500-prcmu: Remove unused inline function
mfd: arizona-spi: Add Android board ACPI table handling
mfd: arizona-spi: Split Windows ACPI init code into its own function
mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS
mfd: intel-lpss: Provide an SSP type to the driver
dt-bindings: mfd: brcm,cru: Rename pinctrl node
dt-bindings: Add compatibles for undocumented trivial syscons
mfd: atmel-flexcom: Fix compilation warning
dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC
dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema
mfd: exynos-lpass: Drop unneeded syscon.h include
mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs
mfd: ab8500: Drop debugfs module
mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC
mfd: ab8500: Rewrite bindings in YAML
mfd: qcom-spmi-pmic: Add pm8953 compatible
...
Documentation/hwmon/sy7636a-hwmon.rst:4: WARNING: Title underline too short.
Kernel driver sy7636a-hwmon
=========================
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/all/YgTRu7iLgJMymeT5@google.com/
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.
TI's TMP464 is an I2C temperature sensor chip. This chip is similar
to TI's TMP421 chip, but with 16bit-wide registers (instead of
8bit-wide registers). The chip has one local sensor and four remote
sensors. TMP468 is similar to TMP464 but has one local and eight
remote sensors.
Originally-from: Agathe Porte <agathe.porte@nokia.com>
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Tested-by: Agathe Porte <agathe.porte@nokia.com>
Link: https://lore.kernel.org/r/20220222223610.23098-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for another Infineon Multi-phase controller chip. The
xdpe11280 uses linear instead of vid data format for VOUT. Detect
VOUT_MODE format during identification and skip the xdpe122 related
adaptions in case it is linear.
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/fa6a4b636a05ecb337d132824efca2545188a2a2.1646214248.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
of the Aquacomputer Farbwerk 360 RGB controller, which communicates through
a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After doing some research, it seems that Fujitsu's
hardware monitoring solution exports data describing
which temperature sensors affect which fans, similar
to the data in fan_source of the ftsteutates driver.
Writing 0 into these registers forces the fans to
full speed.
Export this data with standard attributes.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220224061210.16452-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TMP125 is a 2 degree Celsius accurate Digital
Temperature Sensor with a SPI interface.
The temperature register is a 16-bit, read-only register.
The MSB (Bit 15) is a leading zero and never set. Bits 14
to 5 are the 1+9 temperature data bits in a two's
complement format. Bits 4 to 0 are useless copies of
Bit 5 value and therefore ignored.
This was tested on a Aerohive HiveAP-350.
Bonus: lm70 supports TMP122/TMP124 as well.
I added them to the Kconfig module description.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/43b19cbd4e7f51e9509e561b02b5d8d0e7079fac.1645175187.git.chunkeey@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document the SMM interface as requested by Pali Rohar.
Since Dell does not offer any offical documentation
regarding the SMM interface, the necessary information
was extracted from the dell_smm_hwmon driver and other
sources.
Suggested-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220215191113.16640-7-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A user discovered [1] the CPU Core voltage sensor, which spans 2
registers and provides output in mV. Althroug the discovery was made
with a X470 chipset, the sensor is present in X570 (tested with C8H).
For now simply add it to each board with the CPU current sensor present.
[1] https://github.com/zeule/asus-ec-sensors/issues/12
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
Link: https://lore.kernel.org/r/20220208094244.1106312-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the "label" sysfs attribute, which can contain a descriptive label
that allows to uniquely identify a device within the system.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220110182256.30763-2-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add documentation for peci-cputemp driver that provides DTS thermal
readings for CPU packages and CPU cores, and peci-dimmtemp driver that
provides Temperature Sensor on DIMM readings.
Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20220208153639.255278-13-iwona.winiarska@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a multi-function device to interface with the sy7636a
EPD PMIC chip from Silergy.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The IR38060, IR38164 and IR38263 can be supported using this driver.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Arthur Heymans <arthur.heymans@9elements.com>
Link: https://lore.kernel.org/r/20211213142814.264802-2-arthur.heymans@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver implements monitoring and control of fans plugged into the
device. Besides typical speed monitoring and PWM duty cycle control,
voltage and current are reported for every fan.
The device also has 2 connectors for RGB LEDs, support for them isn't
implemented (mainly because there is no standardized sysfs interface).
Also, the device has a noise sensor, but the sensor seems to be completely
useless (and very imprecise), so support for it isn't implemented too.
The driver coexists with userspace tools that access the device through
hidraw interface with no known issues.
The driver has been tested on x86_64, built in and as a module.
Some changes/improvements were suggested by Jonas Malaco.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20211031033058.151014-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Linux HWMON sensors driver for ASUS motherboards to read
sensors from the embedded controller.
Many ASUS motherboards do not publish all the available
sensors via the Super I/O chip but the missing ones are
available through the embedded controller (EC) registers.
This driver implements reading those sensor data via the
WMI method BREC, which is known to be present in all ASUS
motherboards based on the AMD 500 series chipsets (and
probably is available in other models too). The driver
needs to know exact register addresses for the sensors and
thus support for each motherboard has to be added explicitly.
The EC registers do not provide critical values for the
sensors and as such they are not published to the HWMON.
Supported motherboards:
* PRIME X570-PRO
* Pro WS X570-ACE
* ROG CROSSHAIR VIII HERO
* ROG CROSSHAIR VIII DARK HERO
* ROG CROSSHAIR VIII FORMULA
* ROG STRIX X570-E GAMING
* ROG STRIX B550-I GAMING
* ROG STRIX B550-E GAMING
Co-developed-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Tor Vic <torvic9@mailbox.org>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The INA238 is a I2C power monitor similar to other INA2xx devices,
providing shunt voltage, bus voltage, current, power and temperature
measurements.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20211102052754.817220-3-nathan@nathanrossi.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files
and scripts from Mauro. We are almost at the place where we
can properly check that the running kernel's sysfs abi is
documented fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPbjQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ync9gCfXKMUI1GAnCfJWAwTdTcd18q5akoAoMw32/AH
0yh5TjAWFyFd7xz5d7qs
=itsC
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files and
scripts from Mauro. We are almost at the place where we can
properly check that the running kernel's sysfs abi is documented
fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes"
* tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (122 commits)
device property: Drop redundant NULL checks
x86/build: Tuck away built-in firmware under FW_LOADER
vmlinux.lds.h: wrap built-in firmware support under FW_LOADER
firmware_loader: move struct builtin_fw to the only place used
x86/microcode: Use the firmware_loader built-in API
firmware_loader: remove old DECLARE_BUILTIN_FIRMWARE()
firmware_loader: formalize built-in firmware API
component: do not leave master devres group open after bind
dyndbg: refine verbosity 1-4 summary-detail
gpiolib: acpi: Replace custom code with device_match_acpi_handle()
i2c: acpi: Replace custom function with device_match_acpi_handle()
driver core: Provide device_match_acpi_handle() helper
dyndbg: fix spurious vNpr_info change
dyndbg: no vpr-info on empty queries
dyndbg: vpr-info on remove-module complete, not starting
device property: Add missed header in fwnode.h
Documentation: dyndbg: Improve cli param examples
dyndbg: Remove support for ddebug_query param
dyndbg: make dyndbg a known cli param
dyndbg: show module in vpr-info in dd-exec-queries
...
TMP461 is almost identical to TMP451, which is already supported by the
lm90 driver. At the same time, unlike other sensors from the TMP401
compatible series, it only supports 8-bit temperature read operations,
and it supports negative temperatures when configured for its default
temperature range, and it supports a temperature offset register.
Supporting this chip in the tmp401 driver adds unnecessary complexity.
Remove its support from this driver and support the chip with the lm90
driver instead.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The nominal speed of each fan can be obtained with
i8k_get_fan_nominal_speed(), however the result is not available
from userspace.
Change that by adding fanX_min, fanX_max and fanX_target attributes.
All are RO since fan control happens over pwm.
Tested on a Dell Inspiron 3505 and a Dell Latitude C600.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210926221044.14327-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The appropriate mantissa values for the lm25066 family's direct-format
current and power readings are a function of the sense resistor
employed between the SENSE and VIN pins of the chip. Instead of
assuming that resistance is always the same 1mOhm as used in the
datasheet, allow it to be configured via a device-tree property
("shunt-resistor-micro-ohms").
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-8-zev@bewilderbeest.net
[groeck: Fixed checkpatch warnings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Move the ABI attributes documentation from:
Documentation/hwmon/sysfs-interface.rst
in order for it to follow the usual ABI documentation. That
allows script/get_abi.pl to properly handle it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/5f47619ed882b0b8d1c84b56f7ea17bac0854b77.1632994837.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit id "b00647c46c9d7f6ee1ff6aaf335906101755e614",
adds reporting current and voltage to k10temp.c
The commit id "0a4e668b5d52eed8026f5d717196b02b55fb2dc6",
removed reporting current and voltage from k10temp.c
The curr and in(voltage) entries are not removed from
"k10temp_info" structure. Removing those residue entries.
while at it, update k10temp driver documentation
Signed-off-by: suma hegde <suma.hegde@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210902174155.7365-2-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make top and bottom border lines match.
Documentation/hwmon/sht4x.rst:42: WARNING: Malformed table.
Text in column margin in table line 4.
Fixes: 505c254937 ("hwmon: Add sht4x Temperature and Humidity Sensor Driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Navin Sankar Velliangiri <navin@linumiz.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20210727232054.7426-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds support for the Delta DPS-920AB PSU.
Only missing feature is fan control which the PSU supports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210607103431.2039073-1-robert.marko@sartura.hr
[groeck: Add MODULE_IMPORT_NS(PMBUS);]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add documentation and index link for pim4328 PMBus driver.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwmX_enable supports three possible values:
0: Fan control disabled. Duty cycle is fixed to 0%
1: Fan control enabled, pwm mode. Duty cycle is determined by
values written into Target Duty Cycle registers.
2: Fan control enabled, rpm mode
Duty cycle is adjusted such that fan speed matches
the values in Target Count registers
The current code does not do this; instead, it mixes pwm control
configuration with fan speed monitoring configuration. Worse, it
reports that pwm control would be disabled (pwmX_enable==0) when
it is in fact enabled in pwm mode. Part of the problem may be that
the chip sets the "TACH input enable" bit on its own whenever the
mode bit is set to RPM mode, but that doesn't mean that "TACH input
enable" accurately reflects the pwm mode.
Fix it up and only handle pwm control with the pwmX_enable attributes.
In the documentation, clarify that disabling pwm control (pwmX_enable=0)
sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN
is set together with RPM_MODE.
While at it, only update the configuration register if the configuration
has changed, and only update the cached configuration if updating the
chip configuration was successful.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@cesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-4-linux@roeck-us.net
The MAX31790 has two sets of registers for pwm duty cycles, one to request
a duty cycle and one to read the actual current duty cycle. Both do not
have to be the same.
When reporting the pwm duty cycle to the user, the actual pwm duty cycle
from pwm duty cycle registers needs to be reported. When setting it, the
pwm target duty cycle needs to be written. Since we don't know the actual
pwm duty cycle after a target pwm duty cycle has been written, set the
valid flag to false to indicate that actual pwm duty cycle should be read
from the chip instead of using cached values.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@ceesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-3-linux@roeck-us.net
This patch adds a hwmon driver for the SHT4x Temperature and
Humidity sensor.
Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>
[groeck: dropped unnecessary empty line and continuation lines]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The entry for mp2888 is missing and it causes the following
'make htmldocs' build warning:
Documentation/hwmon/mp2888.rst: WARNING: document isn't included in any toctree
Add the mp2888 entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210521172218.37592-1-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a digital, multi-phase, pulse-width modulation
controller.
This device supports:
- One power rail.
- Programmable Multi-Phase up to 10 Phases.
- PWM-VID Interface
- One pages 0 for telemetry.
- Programmable pins for PMBus Address.
- Built-In EEPROM to Store Custom Configurations.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210511055619.118104-3-vadimp@nvidia.com
[groeck: Add MODULE_IMPORT_NS]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Flex BMR310, BMR456, BMR457, BMR458, BMR480, BMR490,
BMR491 and BMR492 to the pmbus driver
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-4-erik.rosen@metormote.com
[groeck: Fixed minor whitespace error]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add documentation for the new pmbus flags PMBUS_WRITE_PROTECTED,
PMBUS_NO_CAPABILITY and PMBUS_READ_STATUS_AFTER_FAILED_CHECK
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-3-erik.rosen@metormote.com
[groeck: Added newline at end of file]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While UTF-8 characters can be used at the Linux documentation,
the best is to use them only when ASCII doesn't offer a good replacement.
So, replace the occurences of the following UTF-8 characters:
- U+2010 ('‐'): HYPHEN
- U+2013 ('–'): EN DASH
- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/ccdd1bf45963a7748188a97c75f667b37bd43d2f.1620641727.git.mchehab+huawei@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+2010 ('‐'): HYPHEN
as ASCII HYPHEN is preferred over U+2010
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/ba8b5122ac9d4918fd966d0eb0a5ca9d89044b04.1621159997.git.mchehab+huawei@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While UTF-8 characters can be used at the Linux documentation,
the best is to use them only when ASCII doesn't offer a good replacement.
So, replace the occurences of the following UTF-8 characters:
- U+2013 ('–'): EN DASH
In this specific case, EN DASH was used instead of a minus
sign. So, replace it by a single hyphen.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/73b3c7c1eef5c12ddc941624d23689313bd56529.1620744606.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Commit 60268b0e82 ("hwmon: (amd_energy) modify the visibility of
the counters") restricted visibility of AMD energy counters to work
around a side-channel attack using energy data to determine which
instructions are executed. The attack is described in 'PLATYPUS:
Software-based Power Side-Channel Attacks on x86'. It relies on quick
and accurate energy readings.
This change made the counters provided by the amd_energy driver
effectively unusable for non-provileged users. However, unprivileged
read access is the whole point of hardware monitoring attributes.
An attempt to remedy the situation by limiting and randomizing access
to chip registers was rejected by AMD. Since the driver is for all
practical purposes unusable, remove it.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hardware monitoring sysfs attributes are used and displayed by unrestricted
userspace applications. Standard attributes therefore have to be world
readable, since otherwise those userspace applications would either have
to run as super-user or display an error. None of those makes sense.
Clarify the expected scope of attribute access in the ABI document.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus driver support for Maxim MAX15301 InTune Automatically
Compensated Digital PoL Controller with Driver and PMBus Telemetry
Even though the specification does not specifically mention it,
extensive empirical testing has revealed that auto-detection of
limit-registers will fail in a random fashion unless the delay
parameter is set to above about 80us. The default delay is set
to 100us to include some safety margin.
This patch is tested on a Flex BMR461 converter module.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210419101251.24840-1-erik.rosen@metormote.com
[groeck: Added rationale for delay to driver header]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for these devices:
- YH-5151E - the PDU
- YM-2151E - the PSU
The device datasheet says that the devices support PMBus 1.2, but in my
testing, a lot of the commands aren't supported and if they are, they
sometimes behave strangely or inconsistently. For example, writes to the
PAGE command requires using PEC, otherwise the write won't work and the
page won't switch, even though, the standard says that PEC is optional.
On the other hand, writes to SMBALERT don't require PEC. Because of
this, the driver is mostly reverse engineered with the help of a tool
called pmbus_peek written by David Brownell (and later adopted by my
colleague Jan Kundrát).
The device also has some sort of a timing issue when switching pages,
which is explained further in the code.
Because of this, the driver support is limited. It exposes only the
values that have been tested to work correctly.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210414080019.3530794-1-kubernat@cesnet.cz
[groeck: Fixed up "missing braces around initializer" from 0-day]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for TI TPS53676 controller to the tps53679 pmbus driver
The driver uses the USER_DATA_03 register to figure out how many phases
are enabled and to which channel they are assigned, and sets the number
of pages and phases accordingly.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210322193734.75127-3-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPA-RS600 is a compact 600W AC to DC removable power supply module.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210317040231.21490-3-chris.packham@alliedtelesis.co.nz
[groeck: Added bpa-rs600 to index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These are "all-in-one" CPU liquid coolers that can be monitored and
controlled through a proprietary USB HID protocol.
While the models have differently sized radiators and come with varying
numbers of fans, they are all indistinguishable at the software level.
The driver exposes fan/pump speeds and coolant temperature through the
standard hwmon sysfs interface.
Fan and pump control, while supported by the devices, are not currently
exposed. The firmware accepts up to 61 trip points per channel
(fan/pump), but the same set of trip temperatures has to be maintained
for both; with pwmX_auto_point_Y_temp attributes, users would need to
maintain this invariant themselves.
Instead, fan and pump control, as well as LED control (which the device
also supports for 9 addressable RGB LEDs on the CPU water block) are
left for existing and already mature user-space tools, which can still
be used alongside the driver, thanks to hidraw. A link to one, which I
also maintain, is provided in the documentation.
The implementation is based on USB traffic analysis. It has been
runtime tested on x86_64, both as a built-in driver and as a module.
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20210319045544.416138-1-jonas@protocubo.io
[groeck: Removed unnecessary spinlock.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds support for reading the critical values of the temperature sensors
and the rail sensors (voltage and current) once and caches them. Updates
the naming of the constants following a more clear scheme. Also updates
the documentation and fixes some typos. Updates is_visible and ops_read
functions to be more readable.
The new sensors output of a Corsair HX850i will look like this:
corsairpsu-hid-3-1
Adapter: HID adapter
v_in: 230.00 V
v_out +12v: 12.14 V (crit min = +8.41 V, crit max = +15.59 V)
v_out +5v: 5.03 V (crit min = +3.50 V, crit max = +6.50 V)
v_out +3.3v: 3.30 V (crit min = +2.31 V, crit max = +4.30 V)
psu fan: 0 RPM
vrm temp: +46.2°C (crit = +70.0°C)
case temp: +39.8°C (crit = +70.0°C)
power total: 152.00 W
power +12v: 108.00 W
power +5v: 41.00 W
power +3.3v: 5.00 W
curr +12v: 9.00 A (crit max = +85.00 A)
curr +5v: 8.31 A (crit max = +40.00 A)
curr +3.3v: 1.62 A (crit max = +40.00 A)
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YFNg6vGk3sQmyqgB@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for ST STPDDC60 Unversal Digital
Multicell Controller.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-3-erik.rosen@metormote.com
[groeck: Fixed whitespace error in Makefile]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add basic monitoring support as well as port on/off control for Texas
Instruments TPS23861 PoE PSE IC.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210121134434.2782405-2-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16508 is quite similar to MAX16601, except that it does not support
the DEFAULT_NUM_POP register and we thus can not dynamically determine
the number of populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-2-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX16601 can report the number of populated phases. Use this
information to only create sysfs attributes for populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-1-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds a hwmon driver for the AHT10 Temperature and
Humidity sensor. It has a maximum sample rate, as the datasheet
states that the chip may heat up if it is sampled more than once
every two seconds.
Has been tested a to work on a raspberrypi0w
Signed-off-by: Johannes Cornelis Draaijer (datdenkikniet) <jcdra1@gmail.com>
Link: https://lore.kernel.org/r/20210107194014.GA88780@desktop
[groeck: dropped AHT10_ADDR (unused) and use AHT10_MEAS_SIZE where
appropriate; dropped change log]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This deletes the ABx500 hwmon driver, the only supported
variant being the AB8500.
This driver has been replaced by generic frameworks. By
inspecting the abx500 sysfs files we see that it contains
things such as temp1_max, temp1_max_alarm, temp1_max_hyst,
temp1_max_hyst_alarm, temp1_min, temp1_min_alarm.
It becomes obvious that the abx500.c is a reimplementation
of thermal zones. This is not very strange as the generic
thermal zones were not invented when this driver was merged
so people were rolling their own.
The ab8500.c driver contains conversion tables for handling
a thermistor on ADC channels AUX1 and AUX2.
I managed to replace the functionality of the driver with:
- Activation of the ntc_thermistor.c driver,
CONFIG_SENSORS_NTC_THERMISTOR
- Activation of thermal zones, CONFIG_THERMAL
- In the device tree, connecting the NTC driver to the
processed IIO channels from the AB8500 GPADC ADC forming
two instances of NTC sensors.
- Connecting the two NTC sensors to a "chassis" thermal zone
in the device tree and setting that to hit the CPU frequency
at 50 degrees celsius and do a critical shutdown at 70
degrees celsius, deploying a policy using the sensors.
After talking to the original authors we concluded that the
driver was never properly parameterized in production so
what we now have in the device tree is already puts the
thermistors to better use than what the hwmon driver did.
The two remaining channels for two battery temperatures is
already handled in the charging algorithms but can be
optionally extended to thermal zones as well if we want
these to trigger critical shutdown for the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201221125521.768082-1-linus.walleij@linaro.org
[groeck: Removed documentation and fixed up Makefile, Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the Analog Devices ADM1275 bindings to dt-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201117220807.208747-4-krzk@kernel.org
[groeck: Removed unnecessary type ($ref) declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit b722d7b9e4da ("hwmon: (pmbus) Driver for Delta power supplies
Q54SJ108A2") provides new documentation for DELTA Q54SJ108A2NC* drivers,
but the title underline was too short.
make htmldocs warns:
Documentation/hwmon/q54sj108a2.rst:4: WARNING: Title underline too short.
Adjust the title underline to the correct length.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201207152658.32444-1-lukas.bulwahn@gmail.com
[groeck: Adjust subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2992 is a rail-to-rail system monitor that
measures current, voltage, and power of two supplies.
Two ADCs simultaneously measure each supply’s current.
A third ADC monitors the input voltages and four
auxiliary external voltages.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver supports Q54SJ108A2 series modules of Delta.
Standard attributes are in sysfs, and other attributes are in debugfs.
Signed-off-by: xiao.ma <xiao.mx.ma@deltaww.com>
Link: https://lore.kernel.org/r/20201202025900.1842-1-max701@126.com
[groeck: Replaced spaces with tabs, dropped excessive spaces,
fixed module prefix in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the STMicroelectronics pm6764 voltage regulator.
the output voltage use the MFR_READ_VOUT 0xD4
vout value returned is linear11
Signed-off-by: Charles Hsu <hsu.yungteng@gmail.com>
[groeck: Fixed various compile errors; marked pm6764tr_of_match __maybe_unused]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only action currently performed in pmbus_do_remove() is removing the
debugfs hierarchy. We can schedule a devm action at probe time and remove
pmbus_do_remove() entirely from all pmbus drivers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201026105352.20359-1-brgl@bgdev.pl
[groeck: Removed references to pmbus_do_remove from documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
.../Documentation/hwmon/mp2975.rst:25: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:27: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:69: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:70: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:72: WARNING: Bullet list ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst: WARNING: document isn't included in any toctree
List blocks should have blank lines before and after them,
in order to be properly parsed.
Fixes: 4beb7a028e9f ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/b02f98d886ab1f5af233f8999c7a15529fc52cdc.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
New driver and chip support:
- Moortec MR75203 PVT controller
- MPS Multi-phase mp2975 controller
- ADM1266
- Zen3 CPUs
- Intel MAX 10 BMC
Enhancements:
- Support for rated attributes in hwmon core
- MAX20730
- Device monitoring via debugfs
- VOUT readin adjustment vie devicetree bindings
- LM75
- Devicetree support
- Regulator support
- Improved accumulationm logic in amd_energy driver
- Added fan sensor to gsc-hwmon driver
- Support for simplified I2C probing
Various other minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=kwzT
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver and chip support:
- Moortec MR75203 PVT controller
- MPS Multi-phase mp2975 controller
- ADM1266
- Zen3 CPUs
- Intel MAX 10 BMC
Enhancements:
- Support for rated attributes in hwmon core
- MAX20730:
- Device monitoring via debugfs
- VOUT readin adjustment vie devicetree bindings
- LM75:
- Devicetree support
- Regulator support
- Improved accumulationm logic in amd_energy driver
- Added fan sensor to gsc-hwmon driver
- Support for simplified I2C probing
Various other minor fixes and improvements"
* tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (64 commits)
hwmon: (pmbus/max20730) adjust the vout reading given voltage divider
dt-bindings: hwmon: max20730: adding device tree doc for max20730
hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller
hwmon: Add DT bindings schema for PVT controller
dt-bindings: hwmon: Add the +vs supply to the lm75 bindings
dt-bindings: hwmon: Convert lm75 bindings to yaml
docs: hwmon: (ltc2945) update datasheet link
hwmon: (mlxreg-fan) Fix double "Mellanox"
hwmon: (pmbus/max20730) add device monitoring via debugfs
hwmon: (pmbus/max34440) Fix OC fault limits
hwmon: (bt1-pvt) Wait for the completion with timeout
hwmon: (bt1-pvt) Cache current update timeout
hwmon: (bt1-pvt) Test sensor power supply on probe
hwmon: (lm75) Add regulator support
hwmon: Add hwmon driver for Intel MAX 10 BMC
dt-bindings: Add MP2975 voltage regulator device
hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller
hwmon: (tmp513) fix spelling typo in comments
hwmon: (amd_energy) Update driver documentation
hwmon: (amd_energy) Improve the accumulation logic
...
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
chip connects to a set of sensor chips to monitor current, voltage,
thermal and power of different components on board. The BMC firmware is
responsible for sensor data sampling and recording in shared registers.
Host driver reads the sensor data from these shared registers and
exposes them to users as hwmon interfaces.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com
[groeck: Adjusted subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp295 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a dual-loop, digital, multi-phase controller.
This device:
- Supports two power rail.
- Provides 8 pulse-width modulations (PWMs), and can be configured up
to 8-phase operation for rail 1 and up to 4-phase operation for rail
2.
- Supports two pages 0 and 1 for telemetry and also pages 2 and 3 for
configuration.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20200926204957.10268-2-vadimp@nvidia.com
[groeck: Cleaned up a couple of error returns; fixed up API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the documentation with the newly added features
* Set the accumulation interval based on resolution
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-5-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some drives, reading the drive temperature resets the drive's
spin-down timer. If the drive temperature is read too often, affected
drives will never spin down. Add this information as usage note to
the driver documentation.
Reported-by: Peter Sulyok <peter@sulyok.net>
Cc: Peter Sulyok <peter@sulyok.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.
Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New attributes (rated_min/rated_max) are being added the hwmon ABI.
They are needed to cover rated values documented by PMBus
specification:
PMBus Power System Mgt Protocol Specification - Part II – Revision 1.3.1,
chapters: 22.3.1 - 22.3.10, 22.3.15
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-2-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations
to fix overflow issues with 32-bit architectures
Plus various cleanups in several drivers.
-----BEGIN PGP SIGNATURE-----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=nMNN
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations to fix
overflow issues with 32-bit architectures
Plus various cleanups in several drivers"
* tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (adc128d818) Fix advanced configuration register init
hwmon: (axi-fan-control) remove duplicate macros
hwmon: (i5k_amb, vt8231) Drop uses of pci_read_config_*() return value
hwmon: (sparx5) Make symbol 's5_temp_match' static
hwmon: (corsair-cpro) add reading pwm values
hwmon: sparx5: Add Sparx5 SoC temperature driver
dt-bindings: hwmon: Add Sparx5 temperature sensor
hwmon: (tmp401) Replace HTTP links with HTTPS ones
hwmon: (lm95234) Replace HTTP links with HTTPS ones
hwmon: (lm90) Replace HTTP links with HTTPS ones
hwmon: (k8temp) Replace HTTP links with HTTPS ones
hwmon: (jc42) Replace HTTP links with HTTPS ones
hwmon: (ina2xx) Replace HTTP links with HTTPS ones
hwmon: (ina209) Replace HTTP links with HTTPS ones
hwmon: Replace HTTP links with HTTPS ones
docs: hwmon: Replace HTTP links with HTTPS ones
hwmon: (adm1025) Replace HTTP links with HTTPS ones
hwmon: add Corsair Commander Pro driver
hwmon: (max6697) Allow max6581 to create tempX_offset
hwmon: (tmmp513) Replace HTTP links with HTTPS links
...
Currently, acpi.info is an invalid link to access ACPI specification,
the new valid link is https://uefi.org/specifications.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds the possibility for reading pwm values.
These can not be read if the device is controlled via
fan_target or a fan curve and will return an error in
this case. Since an error is expected, this adds some
rudimentary error handling.
Changes:
- add CTL_GET_FAN_PWM and use it via get_data
- pwm returns -ENODATA if the device returns error 0x12
- fan_target now returns -ENODATA when the driver is
started or a pwm value is set.
- add ccp_get_errno to determine errno from device error.
- get_data now has a parameter to determine whether
to read one or two bytes of data.
- update documentation
- fix missing surname in MAINTAINERS
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719192544.61247-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719191534.61181-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719190525.61112-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719183548.61011-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719182539.60944-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719181530.60878-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Duke Du