Enable AHCI on Jetson TX1 and add sata phy node.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car H3, on-chip peripheral modules that can make use of DMA are
wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has been
lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7795 IPMMU-PV1 and keep it disabled by default.
This device is not present in r8a7795 ES1.x and
is removed from the DT of those SoCs.
This corrects an omission in
3b7e7848f0 ("arm64: dts: renesas: r8a7795: Add IPMMU device nodes")
This does not have any runtime effect.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the I2C0 device node.
The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and
Analog Devices ADV7511W HDMI transmitter (but we're only describing the
former chip now).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 parts of the I2C[0-4] device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.
Most features are enabled through the shared salvator-xs.dtsi board
description. The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.
This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#pwm-cells" property to "pwm@e6e31000" device node.
This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#phy-cells" property to "usb-phy@e65ee000" device node.
This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.
This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic support for R-Car Salvator-X M3-N (R8A77965) board.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Gen 3 R-Car M3-N SoC.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sdhci for rk3399-sapphire works for eMMC but keep-power-in-suspend
is an optional property for SDIO.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pinctrl hogs on rk3399-gru-kevin that broke suspend. This gets fixed
by moving the wifi pinctrl to the correct node.
Also revert the usb3 phy-port enablement, as a missing feature in the
type-c phy breaks usb on all non-gru rk3399 boards.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqj23sQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgf9kB/9/dpdz7OVY4u2WPhr7AHZjv+dBl9dt0uI6
1ttbWzH2sXQcfUivy89hAEQYBB3hR5GsZZIIWA9ProsiHpnH6hHQTwRmy/H+2QBI
hg1XyYAh7eiQoOjvMUT6at2SfCRofPbSoLBVo3JBlwlbSCBEy+WpQZjLXWdD+Bqy
Cj1H6PWlCV8p0W7T1YsMfltOM7Kh55tew+1+XTpkEJ2PHgz+Ht1mh4h59nEvG+s/
BdJ2hos9UW/O7OPdpa6pQUGf8/tZRSacmAXL8Z6W+kUzzsDTnYFN2S8cuJ7CeZCY
0+azrYptuSvs+1xAe221axu0GlVPltSC3eylI4pWECpFfh3f/ARK
=iow6
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts64fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 fixes for 4.16" from Heiko Stübner:
Pinctrl got a fix in 4.16-rc1, that exposed an issue with wifi-related
pinctrl hogs on rk3399-gru-kevin that broke suspend. This gets fixed
by moving the wifi pinctrl to the correct node.
Also revert the usb3 phy-port enablement, as a missing feature in the
type-c phy breaks usb on all non-gru rk3399 boards.
* tag 'v4.16-rockchip-dts64fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
Revert "arm64: dts: rockchip: add usb3-phy otg-port support for rk3399"
arm64: dts: rockchip: Fix rk3399-gru-* s2r (pinctrl hogs, wifi reset)
- convert to the SPDX-License-Identifier
- add missing clocks (for the registers) on some of the peripherals
- use the new nand driver
- add more uart for Armada 7K/8K SoCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWqLBBgAKCRALBhiOFHI7
1dQ0AKCOUzXMHkC5/f0hwgPYpmzKuQGZjACfQA6eVistsl3QfTN0Nph57jRW9IE=
=KBPW
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.17-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.17 (part 1)" from Gregory CLEMENT:
- convert to the SPDX-License-Identifier
- add missing clocks (for the registers) on some of the peripherals
- use the new nand driver
- add more uart for Armada 7K/8K SoCs
* tag 'mvebu-dt64-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-cp110: Add apb_pclk clock for the uart nodes
arm64: dts: marvell: use reworked NAND controller driver on Armada 8K
arm64: dts: marvell: use reworked NAND controller driver on Armada 7K
ARM64: dts: marvell: armada-cp110: Add registers clock for sata node
arm64: dts: marvell: armada-8080-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-mcbin: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-7040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-espressobin: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-db: use SPDX-License-Identifier
arm64: dts: marvell: use SPDX-License-Identifier for Armada SoCs
arm64: dts: marvell: mcbin: fix board name typo
arm64: dts: marvell: mcbin: enable uart headers
arm64: dts: marvell: add CP110 uart peripherals
ARM64: dts: marvell: armada-cp110: Add registers clock for I2C nodes
ARM64: dts: marvell: armada-cp110: Add registers clock for SPI nodes
- Add XGE CPLD control support for hip07 SoC
- Disable the SMMU on hip06 and hip07 SoCs becuase of
the hardware limitation
- Enable HS200 mode for the MMC controller on hi6220 hikey board
- Remove "cooling-{min|max}-level" this kind unused properties
for hi6220 SoC
- Add watchdog node for hi6220 SoC
- Remove "CPU_NAP" idle state on hikey960 board since it is
not stable and useless with the updated firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HIMw
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-4.17' of git://github.com/hisilicon/linux-hisi into next/dt
Pull "ARM64: DT: Hisilicon SoC DT updates for 4.17" from Wei Xu:
- Add XGE CPLD control support for hip07 SoC
- Disable the SMMU on hip06 and hip07 SoCs becuase of
the hardware limitation
- Enable HS200 mode for the MMC controller on hi6220 hikey board
- Remove "cooling-{min|max}-level" this kind unused properties
for hi6220 SoC
- Add watchdog node for hi6220 SoC
- Remove "CPU_NAP" idle state on hikey960 board since it is
not stable and useless with the updated firmware
* tag 'hisi-arm64-dt-for-4.17' of git://github.com/hisilicon/linux-hisi:
arm64: dts: Hi3660: Remove 'CPU_NAP' idle state
arm64: dts: hi6220: enable watchdog
ARM64: dts: hi6220: Remove "cooling-{min|max}-level" for CPU nodes
arm64: dts: hikey: Enable HS200 mode on eMMC
arm64: dts: hisi: Disable hisilicon smmu node on hip06/hip07
arm64: dts: hisi: add hns-dsaf cpld control for the hip07 SoC
The ACLK_VIO is a parent clock used by a several children,
its suggested clock rate is 400MHz. Right now it gets 400MHz
because it sources from CPLL(800M) and divides by 2 after reset.
It's good not to rely on default values like this, so let's
explicitly set it.
NOTE: it's expected that at least one board may override cru node and
set the CPLL to 1.6 GHz. On that board it will be very important to be
explicit about aclk-vio being 400 MHz.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add mmc device nodes and proper setup for used pins
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jimin Wang <jimin.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds SATA support fot MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds PCIe support for MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: fix type in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add ethernet device nodes which enable GMAC1 with SGMII interface
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add nodes for NOR flash, parallel Nand flash with error correction code
support.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: RogerCC Lin <rogercc.lin@mediatek.com>
Cc: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch also cleans up two oscillators that provide clocks for MT7623.
Switch the uart clocks to the real ones while at it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clocks, regulators and opp information into cpu nodes.
In addition, the power supply for cpu nodes is deployed on
mt7622-rfb1 board.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable pwrap and MT6380 on mt7622-rfb1 board. Also add all mt6380
regulator nodes in an alone file to allow similar boards using MT6380
able to resue the configuration.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
[mb: add missing space]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add pinctrl device nodes and rfb1 board, additionally include all pin
groups possible being used on rfb1 board and available gpio keys.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT7622 and include header for topckgen,
infracfg, pericfg, apmixedsys, ethsys, sgmiisys, pciesys and ssusbsys
for those devices nodes to be added afterwards.
In addition, provides an oscillator node for the source of PLLs and dummy
clock for PWARP to complement missing support of clock gate for the
wrapper circuit in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This extra clock is needed to access the registers of the UARTs used on
CP110 component of the Armada 7K/8K SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Set correct clocks and interrupt values.
Fixes the incorrect SPI master configuration. This is
mandatory to make the SPI5 interface functional.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add cpu cooling maps for cpu passive trip points. The cpu cooling
device states are mapped to cpufreq based scaling frequencies.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
A 2MB shared memory region is used on MSM8996 for exchanging sector data
in rmtfs. Add this chunk of reserved memory now that we have the
rmtfs-mem compatible to describe it and its memory protection
properties.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a CPU OPP table to allow CPU frequency scaling on msm8916 platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
There are clock controller registers in the APCS block, which purpose
is to control the main CPU mux and divider. Add the clock properties as
part of the APCS device-tree node.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The APCS block was exposed until now as a syscon, but now we have a
proper driver for this block. Add the compatible string of the new
driver to probe and register the mailbox functionality.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a device tree node for the A53 PLL, which exists on msm8916
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
GICv3 does not have affinity bitmap in the binding for PPI
interrupts. It can be specified using a 4th cell if needed
as documented in the bindings. Clean up the wrong use of the
affinity bitmap using the GIC_CPU_MASK_SIMPLE() macro
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device tree files for the Tegra194 P2972-0000 development board.
The board consists of the P2888 compute module and the P2822 baseboard.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the chip-level device tree, including binding headers, for the
NVIDIA Tegra194 "Xavier" system-on-chip. Only a small subset of devices
are initially available, enough to boot to UART console.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Xilinx zc1751 boards is used for silicon validation. Board can be
extended with 5 FMCs/DCs cards to connect various IPs. Describe all
these combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
These 3 boards requires minimal support to get Linux up and running.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu104 is another customer board. It is sort of zcu102 clone
with some differences.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is adding revA, revB and rev1.0. There are also other
revisions between which should be backward compatible with previous
versions. Unfortunately all revs are still in use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This board has 2GB of memory, i2c, sd, wifi sdio, spis, uarts, display
port and usbs.
Board is using fixed clocks because clock driver hasn't been merged yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch add 8-bit bus width property to eMMC node.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the sata port phy OOB timing values in the sata
device-tree node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds a specific wetek dtsi to handle the specific Hub and Play2
boards by no more depending on the p20x dtsi.
This simplifies the hub and play2 dts and will avoid breaking these
boards when adding p200 and p201 specific changes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Different modules maybe installed by the user on the eMMC connector
of the odroid-c2. While the red modules are working without an issue,
it seems some black modules (apparently Samsung based) are having
issue at 200MHz
While the tuning algorithm introduced in v4.14 enables high speed modes
on every other tested designs, it seems a problem remains for this
particular combination of board and eMMC module.
Lowering the maximum frequency of the eMMC on this board until we can
figure out a better solution.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Suggested-by: Ellie Reeves <ellierevves@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The compatible in pwm_AO_cd is wrong and does not match anything.
Correct this with the correct compatible string
Fixes: 4a81e5ddfb ("ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the secure AO system controller with chipid enabled
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
-----BEGIN PGP SIGNATURE-----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=p0sr
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM64 changes for v4.17" from Krzysztof Kozłowski:
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
* tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add OF graph between MHL and USB connector
arm64: dts: exynos: add micro-USB connector node to TM2 platforms
ARM: dts: exynos: Add support for HDMI audio on Exynos 5433 TM2 board
ARM: dts: exynos: Update I2S0 device node in exynos5433
ARM: dts: exynos: Add I2S1 device node to exynos5433
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace the one occurrence with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has one SC2731 PMIC, and the SC2731
PMIC integrates all mobile handset power management, audio codec,
battery management and user interface support function in a single
chip.
This patch adds the SC2731 dts file, as well as adding the RTC and
regulator device node for this PMIC.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has two DMA controllers, one is located
on the ap-ahb system, and another one is located on the agcp system.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the watchdog device node for Spreadtrum SC9860 platform to
watch the system's stability.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will use one always-on timer to be the broadcast device, thus add
the timer device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the pin controller device node for Spreadtrum
SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will access the PMIC through ADI controller, thus this patch adds
the ADI device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform only has one hardware spinlock device,
which is located on AON system of Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OF graph describes MHL data lanes between MHL and respective USB
connector.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since USB connector bindings are available we can describe it on TM2(e).
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Thanks a lot for Vincent Guittot careful work to find bug for 'CPU_NAP'
idle state. At early time, the CPU CA73 CPU_NAP idle state has been
supported on Hikey960. Later we found the system has the hang issue
and for resolving this issue Hisilicon released new MCU firmware, but
unfortunately the new MCU firmware has side effect and results in the
CA73 CPU cannot really enter CPU_NAP state and roll back to WFI state.
After discussion we cannot see the possibility to enable CA73 CPU_NAP
state anymore on Hikey960, based on this conclusion we should remove
this state from DT binding.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch is to add watchdog binding for Hi6220 on Hikey board.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Moreover, the entries are incorrect here as min level is 4 and the max
level is 0.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
According to the hi6220 datasheet, the MMC controller is JEDEC eMMC 4.5
compliant, in addition to supporting a clock of up to 150MHz. The Hikey
schematic also indicates the device utilizes 1.8v signaling. Define these
parameters in the device tree to enable HS200 mode.
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The HiSilicon erratum 161010801 describes the limitation of
HiSilicon platforms hip06/hip07 to support the SMMUv3 mappings
for MSI transactions.
PCIe controller on these platforms has to differentiate the
MSI payload against other DMA payload and has to modify the
MSI payload. This makes it difficult for these platforms to
have SMMU translation for MSI. In order to workaround this,
ARM SMMUv3 driver requires a quirk to treat the MSI regions
separately. Such a quirk is currently missing for DT based
systems and therefore we need to explicitly disable the
hip06/hip07 smmu entries in dts.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add cpld-syscon node to support the cpld control for hns-dsaf
on the hip07 SoC.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable HDMI output on all boards with HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
