This patch also cleans up two oscillators that provide clocks for MT7623.
Switch the uart clocks to the real ones while at it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clocks, regulators and opp information into cpu nodes.
In addition, the power supply for cpu nodes is deployed on
mt7622-rfb1 board.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable pwrap and MT6380 on mt7622-rfb1 board. Also add all mt6380
regulator nodes in an alone file to allow similar boards using MT6380
able to resue the configuration.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
[mb: add missing space]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add pinctrl device nodes and rfb1 board, additionally include all pin
groups possible being used on rfb1 board and available gpio keys.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT7622 and include header for topckgen,
infracfg, pericfg, apmixedsys, ethsys, sgmiisys, pciesys and ssusbsys
for those devices nodes to be added afterwards.
In addition, provides an oscillator node for the source of PLLs and dummy
clock for PWARP to complement missing support of clock gate for the
wrapper circuit in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This extra clock is needed to access the registers of the UARTs used on
CP110 component of the Armada 7K/8K SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Set correct clocks and interrupt values.
Fixes the incorrect SPI master configuration. This is
mandatory to make the SPI5 interface functional.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add cpu cooling maps for cpu passive trip points. The cpu cooling
device states are mapped to cpufreq based scaling frequencies.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
A 2MB shared memory region is used on MSM8996 for exchanging sector data
in rmtfs. Add this chunk of reserved memory now that we have the
rmtfs-mem compatible to describe it and its memory protection
properties.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a CPU OPP table to allow CPU frequency scaling on msm8916 platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
There are clock controller registers in the APCS block, which purpose
is to control the main CPU mux and divider. Add the clock properties as
part of the APCS device-tree node.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The APCS block was exposed until now as a syscon, but now we have a
proper driver for this block. Add the compatible string of the new
driver to probe and register the mailbox functionality.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a device tree node for the A53 PLL, which exists on msm8916
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
GICv3 does not have affinity bitmap in the binding for PPI
interrupts. It can be specified using a 4th cell if needed
as documented in the bindings. Clean up the wrong use of the
affinity bitmap using the GIC_CPU_MASK_SIMPLE() macro
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device tree files for the Tegra194 P2972-0000 development board.
The board consists of the P2888 compute module and the P2822 baseboard.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the chip-level device tree, including binding headers, for the
NVIDIA Tegra194 "Xavier" system-on-chip. Only a small subset of devices
are initially available, enough to boot to UART console.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Xilinx zc1751 boards is used for silicon validation. Board can be
extended with 5 FMCs/DCs cards to connect various IPs. Describe all
these combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
These 3 boards requires minimal support to get Linux up and running.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu104 is another customer board. It is sort of zcu102 clone
with some differences.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is adding revA, revB and rev1.0. There are also other
revisions between which should be backward compatible with previous
versions. Unfortunately all revs are still in use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This board has 2GB of memory, i2c, sd, wifi sdio, spis, uarts, display
port and usbs.
Board is using fixed clocks because clock driver hasn't been merged yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch add 8-bit bus width property to eMMC node.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the sata port phy OOB timing values in the sata
device-tree node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds a specific wetek dtsi to handle the specific Hub and Play2
boards by no more depending on the p20x dtsi.
This simplifies the hub and play2 dts and will avoid breaking these
boards when adding p200 and p201 specific changes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Different modules maybe installed by the user on the eMMC connector
of the odroid-c2. While the red modules are working without an issue,
it seems some black modules (apparently Samsung based) are having
issue at 200MHz
While the tuning algorithm introduced in v4.14 enables high speed modes
on every other tested designs, it seems a problem remains for this
particular combination of board and eMMC module.
Lowering the maximum frequency of the eMMC on this board until we can
figure out a better solution.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Suggested-by: Ellie Reeves <ellierevves@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The compatible in pwm_AO_cd is wrong and does not match anything.
Correct this with the correct compatible string
Fixes: 4a81e5ddfb ("ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the secure AO system controller with chipid enabled
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
-----BEGIN PGP SIGNATURE-----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=p0sr
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM64 changes for v4.17" from Krzysztof Kozłowski:
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
* tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add OF graph between MHL and USB connector
arm64: dts: exynos: add micro-USB connector node to TM2 platforms
ARM: dts: exynos: Add support for HDMI audio on Exynos 5433 TM2 board
ARM: dts: exynos: Update I2S0 device node in exynos5433
ARM: dts: exynos: Add I2S1 device node to exynos5433
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace the one occurrence with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has one SC2731 PMIC, and the SC2731
PMIC integrates all mobile handset power management, audio codec,
battery management and user interface support function in a single
chip.
This patch adds the SC2731 dts file, as well as adding the RTC and
regulator device node for this PMIC.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has two DMA controllers, one is located
on the ap-ahb system, and another one is located on the agcp system.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the watchdog device node for Spreadtrum SC9860 platform to
watch the system's stability.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will use one always-on timer to be the broadcast device, thus add
the timer device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the pin controller device node for Spreadtrum
SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will access the PMIC through ADI controller, thus this patch adds
the ADI device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform only has one hardware spinlock device,
which is located on AON system of Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OF graph describes MHL data lanes between MHL and respective USB
connector.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since USB connector bindings are available we can describe it on TM2(e).
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Thanks a lot for Vincent Guittot careful work to find bug for 'CPU_NAP'
idle state. At early time, the CPU CA73 CPU_NAP idle state has been
supported on Hikey960. Later we found the system has the hang issue
and for resolving this issue Hisilicon released new MCU firmware, but
unfortunately the new MCU firmware has side effect and results in the
CA73 CPU cannot really enter CPU_NAP state and roll back to WFI state.
After discussion we cannot see the possibility to enable CA73 CPU_NAP
state anymore on Hikey960, based on this conclusion we should remove
this state from DT binding.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch is to add watchdog binding for Hi6220 on Hikey board.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Moreover, the entries are incorrect here as min level is 4 and the max
level is 0.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
According to the hi6220 datasheet, the MMC controller is JEDEC eMMC 4.5
compliant, in addition to supporting a clock of up to 150MHz. The Hikey
schematic also indicates the device utilizes 1.8v signaling. Define these
parameters in the device tree to enable HS200 mode.
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The HiSilicon erratum 161010801 describes the limitation of
HiSilicon platforms hip06/hip07 to support the SMMUv3 mappings
for MSI transactions.
PCIe controller on these platforms has to differentiate the
MSI payload against other DMA payload and has to modify the
MSI payload. This makes it difficult for these platforms to
have SMMU translation for MSI. In order to workaround this,
ARM SMMUv3 driver requires a quirk to treat the MSI regions
separately. Such a quirk is currently missing for DT based
systems and therefore we need to explicitly disable the
hip06/hip07 smmu entries in dts.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add cpld-syscon node to support the cpld control for hns-dsaf
on the hip07 SoC.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable HDMI output on all boards with HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This reverts commit c301b327ae.
While this works splendidly on rk3399-gru devices using the cros-ec
extcon, other rk3399-based devices using the fusb302 or no power-delivery
controller at all don't probe at all anymore, as the typec-phy currently
always expects the extcon to be available and therefore defers probing
indefinitly on these.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Back in the early days when gru devices were still under development
we found an issue where the WiFi reset line needed to be configured as
early as possible during the boot process to avoid the WiFi module
being in a bad state.
We found that the way to get the kernel to do this in the earliest
possible place was to configure this line in the pinctrl hogs, so
that's what we did. For some history here you can see
<http://crosreview.com/368770>. After the time that change landed in
the kernel, we landed a firmware change to configure this line even
earlier. See <http://crosreview.com/399919>. However, even after the
firmware change landed we kept the kernel change to deal with the fact
that some people working on devices might take a little while to
update their firmware.
At this there are definitely zero devices out in the wild that have
firmware without the fix in it. Specifically looking in the firmware
branch several critically important fixes for memory stability landed
after the patch in coreboot and I know we didn't ship without those.
Thus, by now, everyone should have the new firmware and it's safe to
not have the kernel set this up in a pinctrl hog.
Historically, even though it wasn't needed to have this in a pinctrl
hog, we still kept it since it didn't hurt. Pinctrl would apply the
default hog at bootup and then would never touch things again. That
all changed with commit 981ed1bfbc ("pinctrl: Really force states
during suspend/resume"). After that commit then we'll re-apply the
default hog at resume time and that can screw up the reset state of
WiFi. ...and on rk3399 if you touch a device on PCIe in the wrong way
then the whole system can go haywire. That's what was happening.
Specifically you'd resume a rk3399-gru-* device and it would mostly
resume, then would crash with some crazy weird crash.
One could say, perhaps, that the recent pinctrl change was at fault
(and should be fixed) since it changed behavior. ...but that's not
really true. The device tree for rk3399-gru is really to blame.
Specifically since the pinctrl is defined in the hog and not in the
"wlan-pd-n" node then the actual user of this pin doesn't have a
pinctrl entry for it. That's bad.
Let's fix our problems by just moving the control of
"wlan_module_reset_l pinctrl" out of the hog and put them in the
proper place.
NOTE: in theory, I think it should actually be possible to have a pin
controlled _both_ by the hog and by an actual device. Once the device
claims the pin I think the hog is supposed to let go. I'm not 100%
sure that this works and in any case this solution would be more
complex than is necessary.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: 48f4d9796d ("arm64: dts: rockchip: add Gru/Kevin DTS")
Fixes: 981ed1bfbc ("pinctrl: Really force states during suspend/resume")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The memory node in fsl-ls1046a.dtsi has no 'reg' property, and causes
the dtc warning below.
Warning (unit_address_vs_reg): Node /memory@80000000 has a unit name, but no reg property
Let's add a 'reg' property with dummy memory size, since bootloader will
need to fill the correct one per board memory configuration anyway.
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Li Yang <leoyang.li@nxp.com>
Currently the size of GICv2m MSI frames are listed as 4kB while the
Juno TRM specifies 64kB for each of these MSI frames.
Though the devices connected themselves might just use the first 4kB,
to be consistent with the general practice of 64kB boundary alignment
to all the devices, let's keep the size as 64kB. This might also help
in avoiding any surprise when passing the device to a VM.
This patch increases the size of each GICv2m MSI frames from 4kB to 64kB
as per the specification.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
It fixes LS family SoCs device tree dtc warning in IFC child nodes.
Warning (simple_bus_reg): Node /soc/ifc@1530000/nor@0,0 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/ifc@1530000/nand@1,0 simple-bus unit address format error, expected "100000000"
Warning (simple_bus_reg): Node /soc/ifc@1530000/board-control@2,0 simple-bus unit address format error, expected "200000000"
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the AHCI SATA
controller used on the Armada 7K/8K SoCs.
The ahci drivers was already designed to support up to 5 clocks so there
is only need to update the device tree to use it. It was not noticed
until now because of wrong assumption in the clock drivers, but as this
IP really needs 2 clocks, we had to declare both of them.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Juno's GICv2m implementation consists of four frames providing 32
interrupts each. Since it is possible to plug in enough PCIe endpoints
to consume more than 32 MSIs, and the driver already has a bodge to
handle multiple frames, let's expose the other three as well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
According to PSCI standard v0.2, for CPU_SUSPEND call, which is
used by cpu idle framework, bit[16] of state parameter must be 0.
So update bit[16] of property 'arm,psci-suspend-param', which is
used as state parameter, to 0.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SPDX identifier as was done by for example by:
"License cleanup: add SPDX GPL-2.0 license identifier to files with no
license" (commit <b24413180f5600bcb3bb70fbed5cf186b60864bd>)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch
"devicetree: Add compatible string for Zynq Ultrascale+ MPSoC"
(commit <988d6f07fc0a29e392035ba56e3bcfaf7b397d95>)
introduced specific compatible string for ZynqMP which should be used
first.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
adding the grf-vio clock to the edp so that it can also be build
as module, correct pcie ep-gpio on the sapphire board and finally
a fix that makes the gmac work at gigabit speeds on the rk3328-rock64.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqHdkUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVVtCACHTxf9/v7UFuXMDtcYRVKZaxwGe9U06RlU
CNRLJADT300B+feHRyh2WiJvNOX4ZJeDotYkXBe/73xMp9AeLv1gTwQBQD1juAfr
wZIXl5/P0zYFQV95oPgHOAGj89rMgvuHFGe2loO2GtIoAiZTcjNUel1SwUCNVzQL
OVei4Z0EGx0Nk5lEFChY0pSg0cZzDko+NGSYYPeQ1qtLJffuOZAq9tG0eJAlUted
qSCXKJnxy5cZ8FxLeuJmP2xGjiZMYLg20kr5DevRnpQTDCCP73VPIPv0IqO+YtfB
5Cmtf8cy/GNxcG1sgK1RMW6ytP+kmBX74I6xtpUAQtaQy1Ah4jDN
=QsKz
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 fixes for 4.16" from Heiko Stübner:
Fixes of dwmmc tuning clocks that may make probing HS cards fail,
adding the grf-vio clock to the edp so that it can also be build
as module, correct pcie ep-gpio on the sapphire board and finally
a fix that makes the gmac work at gigabit speeds on the rk3328-rock64.
* tag 'v4.16-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix DWMMC clocks
arm64: dts: rockchip: introduce pclk_vio_grf in rk3399-eDP device node
arm64: dts: rockchip: correct ep-gpios for rk3399-sapphire
arm64: dts: rockchip: fix rock64 gmac2io stability issues
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc recently added PCI bus checks. Fix these warnings:
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (pci_bridge): Node /pci missing bus-range for PCI bridge
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (unit_address_vs_reg): Node /pci has a reg or ranges property, but no unit name
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Define the Condor board dependent part of the EtherAVB device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A77980 SoC based Condor board.
The board has 1 debug serial port (SCIF0); include support for it, so
that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: correct memory size to 0x78000000 (2GiB)]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the EtherAVB device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF ports in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While the sapphire board is a system-on-module and mostly used with the
excavator baseboard, it is also possible to use it standalone without
any base. So add a board-variant for this type.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The i2s2 drives the HDMI audio, which has the connector on the daughterboard.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The sdio signals are routed through the connector to the baseboard,
where the wifi module is also located. So move the sdio node to
the excavator as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Enable the NXP SGTL5000 audio codec on the RK3399-Q7 EVK baseboard
Haikou.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The I2S definition is part of the SoM and therefore should be in
rk3399-puma.dtsi. Also correct the number of channels available.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The vdd_log power supply is controlled by a PWM pin, not by i2c
register access. There is a boot message that reports an error
about not being able to bring that supply up.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Haikou is a Qseven and μQseven baseboard used in Theobroma Systems
evaluation kits. This dts adds a version for use with a RK3368-uQ7 SoM
called Lion.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK3368-uQ7 SoM is a uQseven-compatible (40mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3368.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit 1.8V interface)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet with on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI-DSI/LVDS
* MIPI-CSI
* USB
- 1x USB 2.0 dual-role
- 1x USB 2.0 host
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the DU, providing only the VGA output for now.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
Fix up all instances of the incorrect clock names across the 64-bit DTs.
Fixes: d717f7352e ("arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs")
Fixes: b790c2cab5 ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Using a serial console on RK3328 provokes an error from
of_dma_request_slave_channel() since the UART nodes have a "dmas"
property but are missing the mandatory "dma-names" to go with it.
Replace the bogus "#dma-cells" - these UARTs are DMA channel consumers,
not providers - with the appropriate names instead. DMA still doesn't
actually work, since the PL330 driver doesn't quite implement everything
the 8250 driver demands, but at least it makes the DT correct.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch updates the sound node of the exynos5433-tm2 board
and adds clock tree configuration in order to support HDMI sound.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The i2s0 node name is changed to a more generic "i2s" and missing
(optional) properties are added. The #sound-dai-cells property is
required for HDMI audio support on TM2 board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add DT node for the second I2S controller available
on Exynos 5433 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Define the generic r8a77995 part of the DU device node.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The single SDHI controller is connected to eMMC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77995 has a VSPBS to support image processing such as blending of
two input images, and has two VSPDs to handle display pipelines with a
DU.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[simon: updated base address of vsp node to fea28000]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPVB handles the interface between the VSPB and memory, while the
FCPVD handles the interface between the VSPD and memory.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify EtherAVB PHY IRQ in the Eagle board's device tree, now that we
have the GPIO support (previously phylib had to resort to polling).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe all 6 GPIO controllers in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the DAI blocks to the device tree. I2S0 and I2S1 are for
connecting to an external codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The S/PDIF transmitter can be reached on the Euler connector.
But as this is a GPIO then leave it disabled so that an overlay
can override the status property.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the device tree sound bindings for the S/PDIF block.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block and pin to the A64 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A 'C' was missing in the model name, this patch fixes it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add description of the J25 and J27 UART headers of the Macchiatobin. They use
uart peripherals that the CP0 (J25) and CP1 (J27) provide.
Even though J25 and J27 are labeled as UART header, the pins on these headers
can be muxed for other purposes. But the UART functionality is useful when the
board is mounted in an ATX style enclosure, since the console UART is not
accessible through the microUSB at CON9.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The CP110 component has 4 uart peripherals. All of them use the same clock
gate for slow peripherals that is shared with the i2c and spi peripherals.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the I2C controller
used on the Armada 7K/8K SoCs.
This follows the changes already made in the binding documentation (as
well as in the driver) in:
commit 1534156e99 ("i2c: mv64xxx: Fix clock
resource by adding an optional bus clock")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the SPI controller
used on Armada 7K/8K SoCs.
This follows the changes already made in the binding documentation (as
well as in the driver) in:
'commit 92ae112e47 ("spi: orion: Fix clock
resource by adding an optional bus clock")'.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enable cdn_dp and create a cdn-dp-sound for the DP audio. Delete the
endpoints between dp and vopL for gru, since we want the DP only use
VOP big, which can support 4K mode.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[dropped vop-hacks]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a node for the cdn DP controller which is embedded in the rk3399
SoC.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[fixed whitespaces instead of tabs, dropped unnecessary address+size-cells
and fixed the number of interrupt cells]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the (previously omitted) SCIF0 pin data to the Eagle board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend configuring the MAC address from u-boot to all meson boards.
I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
With the adequate configuration settings, u-boot will loop through the
list of aliases looking for "ethernetX".
By adding an ethernet alias, u-boot can fixup the local-mac-address
property in the kernel's device tree using a value held in its
environment variable ethaddr.
Tested-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The UART_A is connected to a BT module on the S400 board.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Explictly request the pinctrl info for the UART_AO_A controller,
otherwise we may need to rely on bootloader for the initialization.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Describe the pinctrl info for the UART controller which is found
in the Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: s/uart_ao_b_gpioz/uart_ao_b_z/ ]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
When update the clock info for the UART controller in the EE domain,
the driver explicitly require 'pclk' in order to work properly.
With current logic of the code, the driver will go for the legacy clock probe
routine if it find current compatible string match to 'amlogic,meson-uart',
which result in not requesting the 'pclk' clock, thus break the driver in the end.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Comparing to RGMII interface, the RMII interface require few pins.
So it's worth describing them here.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In the S400 board, The I2C master-1 is connecting to
the audio speaker daughter board.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Describe all the pin mux for the I2C controller which found in
Meson-AXG SoC.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are four I2C masters in EE domain, and one I2C Master in
AO domain, the DT info here should describe them all.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The address space range is actually 0x18, fixed here.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
R-Car D3 does not have the Stream Buffer for EtherAVB-IF (STBE).
Note that the RAVB driver does not use this region.
Fixes: f9ba0c4cfe ("arm64: dts: renesas: r8a77995: Add EthernetAVB device node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car V3M does not have the Stream Buffer for EtherAVB-IF (STBE).
Note that the RAVB driver does not use this region.
Fixes: bea2ab136e ("arm64: dts: renesas: r8a77970: add EtherAVB support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC1/2 in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A77980 SoC device tree including Cortex-A53 CPU, GIC, timer,
CPG, RST, and SYSC.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No devices to add, I2C1 has an external connector only.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enables EEPROM on I2C0 on the Draak board.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To be able to read fused calibration values from hardware the size of
the register resource of TSC1 needs to be incremented to cover one more
register which holds the information if the calibration values have been
fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To be able to read fused calibration values from hardware the size of
the register resource of TSC1 needs to be incremented to cover one more
register which holds the information if the calibration values have been
fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move pmu_a53 and timer nodes from soc node to root node. The nodes that
have been moved do not have any register properties and thus shouldn't be
placed on the bus.
This problem is flagged by the compiler as follows:
$ make W=1
...
arch/arm64/boot/dts/renesas/r8a77995-draak.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a77995-draak.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move timer node from soc node to root node. The node that have been moved
do not have any register properties and thus shouldn't be placed on the
bus.
This problem is flagged by the compiler as follows:
$ make W=1
...
DTC arch/arm64/boot/dts/renesas/r8a77970-eagle.dtb
arch/arm64/boot/dts/renesas/r8a77970-eagle.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a77970-v3msk.dtb
arch/arm64/boot/dts/renesas/r8a77970-v3msk.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We need to configure its GPIOs later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define OOP tables for all CPUs.
This allows CPUFreq to function.
Based in part on work by Hien Dang.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Define OOP tables for all CPUs.
This allows CPUFreq to function.
Based in part on work by Hien Dang.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Move scif node so that sub-nodes of the root node are in
alphabetical order.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
