commit cabce92dd8 upstream.
In RDDM EE, device can not process MHI reset issued by host. In case of MHI
power off, host is issuing MHI reset and polls for it to get cleared until
it times out. Since this timeout can not be avoided in case of RDDM, skip
the MHI reset in this scenarios.
Cc: <stable@vger.kernel.org>
Fixes: a6e2e3522f ("bus: mhi: core: Add support for PM state transitions")
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/1684390959-17836-1-git-send-email-quic_qianyu@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96562c45af upstream.
It is an almost improbable error case but when page allocating loop in
nfs4_get_device_info() fails then we should only free the already
allocated pages, as __free_page() can't deal with NULL arguments.
Found by Linux Verification Center (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88975a5596 upstream.
We must ensure that the subrequests are joined back into the head before
we can retransmit a request. If the head was not on the commit lists,
because the server wrote it synchronously, we still need to add it back
to the retransmission list.
Add a call that mirrors the effect of nfs_cancel_remove_inode() for
O_DIRECT.
Fixes: ed5d588fe4 ("NFS: Try to join page groups before an O_DIRECT retransmission")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2349da0fa upstream.
Drivers that enable runtime PM must make sure that the controller is
runtime resumed before accessing its registers to prevent the power
domain from being disabled.
Fixes: 8def929c40 ("clk: qcom: Add modem clock controller driver for SC7180")
Cc: stable@vger.kernel.org # 5.7
Cc: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230718132902.21430-8-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97112c83f4 upstream.
Drivers that enable runtime PM must make sure that the controller is
runtime resumed before accessing its registers to prevent the power
domain from being disabled.
Fixes: 6cdef2738d ("clk: qcom: Add Q6SSTOP clock controller for QCS404")
Cc: stable@vger.kernel.org # 5.5
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230718132902.21430-7-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d207400fd upstream.
The QMI TLV value for strings in a lot of qmi element info structures
account for null terminated strings with MAX_LEN + 1. If a string is
actually MAX_LEN + 1 length, this will cause an out of bounds access
when the NULL character is appended in decoding.
Fixes: 9b8a11e826 ("soc: qcom: Introduce QMI encoder/decoder")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Link: https://lore.kernel.org/r/20230801064712.3590128-1-quic_ipkumar@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1583694bb4 upstream.
The pll0_vote clock definitely should have pll0 as a parent (instead of
pll8).
Fixes: 7792a8d671 ("clk: mdm9615: Add support for MDM9615 Clock Controllers")
Cc: stable@kernel.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230512211727.3445575-7-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72d00e560d upstream.
Since commit b09c68dc57 ("clk: imx: pll14xx: Support dynamic rates"),
the driver has the ability to dynamically compute PLL parameters to
approximate the requested rates. This is not always used, because the
logic is as follows:
- Check if the target rate is hardcoded in the frequency table
- Check if varying only kdiv is possible, so switch over is glitch free
- Compute rate dynamically by iterating over pdiv range
If we skip the frequency table for the 1443x PLL, we find that the
computed values differ to the hardcoded ones. This can be valid if the
hardcoded values guarantee for example an earlier lock-in or if the
divisors are chosen, so that other important rates are more likely to
be reached glitch-free.
For rates (393216000 and 361267200, this doesn't seem to be the case:
They are only approximated by existing parameters (393215995 and
361267196 Hz, respectively) and they aren't reachable glitch-free from
other hardcoded frequencies. Dropping them from the table allows us
to lock-in to these frequencies exactly.
This is immediately noticeable because they are the assigned-clock-rates
for IMX8MN_AUDIO_PLL1 and IMX8MN_AUDIO_PLL2, respectively and a look
into clk_summary so far showed that they were a few Hz short of the target:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267196 0 0 50000 N
audio_pll1_out 1 1 0 393215995 0 0 50000 Y
and afterwards:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267200 0 0 50000 N
audio_pll1_out 1 1 0 393216000 0 0 50000 Y
This change is equivalent to adding following hardcoded values:
/* rate mdiv pdiv sdiv kdiv */
PLL_1443X_RATE(393216000, 655, 5, 3, 23593),
PLL_1443X_RATE(361267200, 497, 33, 0, -16882),
Fixes: 053a4ffe29 ("clk: imx: imx8mm: fix audio pll setting")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 172044e30b upstream.
select:false makes the schema basically ignored and not effective, which
is clearly not what we want for a device binding.
Fixes: 352546805a ("dt-bindings: clock: Add bindings for versal clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230728165923.108589-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5301c9071 upstream.
First argument of acpi_*_address_space_handler() APIs is acpi_handle of
the device, which is incorrectly passed in driver ->remove() path here.
Fix it by passing the appropriate argument and while at it, make both
API calls consistent using ACPI_HANDLE().
Fixes: a0b028597d ("pinctrl: cherryview: Add support for GMMR GPIO opregion")
Cc: stable@vger.kernel.org
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 358ad816e5 upstream.
Older PA-RISC machines have LEDs which show the disk- and LAN-activity.
The computation is done in software and takes quite some time, e.g. on a
J6500 this may take up to 60% time of one CPU if the machine is loaded
via network traffic.
Since most people don't care about the LEDs, start with LEDs disabled and
just show a CPU heartbeat LED. The disk and LAN LEDs can be turned on
manually via /proc/pdc/led.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4db89524b0 upstream.
Fix the LAN receive and LAN transmit LEDs, which where swapped
up to now.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb78fa86e upstream.
test_pages() tests the page allocator by calling alloc_pages() with
different orders up to order 10.
However, different architectures and platforms support different maximum
contiguous allocation sizes. The default maximum allocation order
(MAX_ORDER) is 10, but architectures can use CONFIG_ARCH_FORCE_MAX_ORDER
to override this. On platforms where this is less than 10, test_meminit()
will blow up with a WARN(). This is expected, so let's not do that.
Replace the hardcoded "10" with the MAX_ORDER macro so that we test
allocations up to the expected platform limit.
Link: https://lkml.kernel.org/r/20230714015238.47931-1-ajd@linux.ibm.com
Fixes: 5015a300a5 ("lib: introduce test_meminit module")
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Cc: Xiaoke Wang <xkernel.wang@foxmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9f71a0335 upstream.
Drivers that enable runtime PM must make sure that the controller is
runtime resumed before accessing its registers to prevent the power
domain from being disabled.
Fixes: 892df0191b ("clk: qcom: Add QCS404 TuringCC")
Cc: stable@vger.kernel.org # 5.2
Cc: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230718132902.21430-9-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cfe75f0f1 upstream.
Fix the test for the AST2200 in the DRAM initialization. The value
in ast->chip has to be compared against an enum constant instead of
a numerical value.
This bug got introduced when the driver was first imported into the
kernel.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 312fec1405 ("drm: Initial KMS driver for AST (ASpeed Technologies) 2000 series (v2)")
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.5+
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com> # AST2600
Link: https://patchwork.freedesktop.org/patch/msgid/20230621130032.3568-2-tzimmermann@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c948ff727e upstream.
To make sure that the controller is runtime resumed and its power domain
is enabled before accessing its registers during probe, the synchronous
runtime PM interface must be used.
Fixes: 8d4025943e ("clk: qcom: camcc-sc7180: Use runtime PM ops instead of clk ones")
Cc: stable@vger.kernel.org # 5.11
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230718132902.21430-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90a0e5265 upstream.
Do not assing the Linux device to struct fb_info.dev. The call to
register_framebuffer() initializes the field to the fbdev device.
Drivers should not override its value.
Fixes a bug where the driver incorrectly decreases the hardware
device's reference counter and leaks the fbdev device.
v2:
* add Fixes tag (Dan)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 88017bda96 ("ep93xx video driver")
Cc: <stable@vger.kernel.org> # v2.6.32+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613110953.24176-15-tzimmermann@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e370b64c7d upstream.
The storage was not draining I/Os and the work load was not spread out
across different CPUs evenly. This led to firmware resource counters
getting overrun on the busy CPU. This overrun prevented error recovery from
happening in a timely manner.
By switching the counter to atomic, it allows the count to be little more
accurate to prevent the overrun.
Cc: stable@vger.kernel.org
Fixes: da7c21b72a ("scsi: qla2xxx: Fix command flush during TMF")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230821130045.34850-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ba0b018f9 upstream.
TMF was returned with an error code. The error code was not preserved to be
returned to upper layer. Instead, the error code from the Marker was
returned.
Preserve error code from TMF and return it to upper layer.
Cc: stable@vger.kernel.org
Fixes: da7c21b72a ("scsi: qla2xxx: Fix command flush during TMF")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230821130045.34850-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d0b65569c upstream.
Fix race condition between Interrupt thread and Chip reset thread in trying
to flush the same mailbox. With the race condition, the "ha->mbx_intr_comp"
will get an extra complete() call. The extra complete call create erroneous
mailbox timeout condition when the next mailbox is sent where the mailbox
call does not wait for interrupt to arrive. Instead, it advances without
waiting.
Add lock protection around the check for mailbox completion.
Cc: stable@vger.kernel.org
Fixes: b2000805a9 ("scsi: qla2xxx: Flush mailbox commands on chip reset")
Signed-off-by: Quinn Tran <quinn.tran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230821130045.34850-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9105c4b7a upstream.
User accidently passed module parameter ql2xenabledif=1 which is
unsupported. However, driver still initialized which lead to guard tag
errors during device discovery.
Remove unsupported ql2xenabledif=1 option and validate the user input.
Cc: stable@vger.kernel.org
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230821130045.34850-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d3148d8e8 upstream.
Task management can retry up to 5 times when FW resource becomes bottle
neck. Between the retries, there is a short sleep. Current code assumes
the chip has not reset or session has not changed.
Check for chip reset or session change before sending Task management.
Cc: stable@vger.kernel.org
Fixes: 9803fb5d27 ("scsi: qla2xxx: Fix task management cmd failure")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-9-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39d2274071 upstream.
Connection does not resume after a host reset / chip reset. The cause of
the blockage is due to the FCF_ASYNC_ACTIVE left on. The gnl command was
interrupted by the chip reset. On exiting the command, this flag should be
turn off to allow relogin to reoccur. Clear this flag to prevent blockage.
Cc: stable@vger.kernel.org
Fixes: 17e64648aa ("scsi: qla2xxx: Correct fcport flags handling")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b51f35d12 upstream.
Link up failure occurred where driver failed to see certain events from FW
indicating link up (AEN 8011) and fabric login completion (AEN 8014).
Without these 2 events, driver would not proceed forward to scan the
fabric. The cause of this is due to delay in the receive of interrupt for
Mailbox 60 that causes qla to set the fw_started flag late. The late
setting of this flag causes other interrupts to be dropped. These dropped
interrupts happen to be the link up (AEN 8011) and fabric login completion
(AEN 8014).
Set fw_started flag early to prevent interrupts being dropped.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7c21b72a upstream.
For each TMF request, driver iterates through each qpair and flushes
commands associated to the TMF. At the end of the qpair flush, a Marker is
used to complete the flush transaction. This process was repeated for each
qpair. The multiple flush and marker for this TMF request seems to cause
confusion for FW.
Instead, 1 flush is sent to FW. Driver would wait for FW to go through all
the I/Os on each qpair to be read then return. Driver then closes out the
transaction with a Marker.
Cc: stable@vger.kernel.org
Fixes: d90171dd0d ("scsi: qla2xxx: Multi-que support for TMF")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 009e7fe4a1 upstream.
Different behavior were experienced of session being torn down vs not when
TMF is timed out. When FW detects the time out, the session is torn down.
When driver detects the time out, the session is not torn down.
Allow TMF error to return to upper layer without session tear down.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-10-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dfe4344c1 upstream.
System crash when using debug kernel due to link list corruption. The cause
of the link list corruption is due to session deletion was allowed to queue
up twice. Here's the internal trace that show the same port was allowed to
double queue for deletion on different cpu.
20808683956 015 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1
20808683957 027 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1
Move the clearing/setting of deleted flag lock.
Cc: stable@vger.kernel.org
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8ec192427 upstream.
Per FW recommendation, 8 TMF's can be outstanding for each
function. Previously, it allowed 8 per target.
Limit TMF to 8 per function.
Cc: stable@vger.kernel.org
Fixes: 6a87679626 ("scsi: qla2xxx: Fix task management cmd fail due to unavailable resource")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efa74a62aa upstream.
During NVMe queue creation, a new qpair is created. FW resource limit needs
to be re-adjusted to take into account the new qpair. Otherwise, NVMe
command can not go through. This issue was discovered while
testing/forcing FW execution to fail at load time.
Add call to readjust IOCB and exchange limit.
In addition, get FW state command and require FW to be running. Otherwise,
error is generated.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 45500dc4e0 ]
io-wq will retry iopoll even when it failed with -EAGAIN. If that
races with task exit, which sets TIF_NOTIFY_SIGNAL for all its workers,
such workers might potentially infinitely spin retrying iopoll again and
again and each time failing on some allocation / waiting / etc. Don't
keep spinning if io-wq is dying.
Fixes: 561fb04a6a ("io_uring: replace workqueue usage with io-wq")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Dylan Yudaken <dylany@meta.com>
[ upstream commit c06c6c5d27 ]
This is required for the failure case (io_req_complete_failed) and is
missing.
The alternative would be to only lock in the failure path, however all of
the non-error paths in io_poll_check_events that do not do not return
IOU_POLL_NO_ACTION end up locking anyway. The only extraneous lock would
be for the multishot poll overflowing the CQE ring, however multishot poll
would probably benefit from being locked as it will allow completions to
be batched.
So it seems reasonable to lock always.
Signed-off-by: Dylan Yudaken <dylany@meta.com>
Link: https://lore.kernel.org/r/20221124093559.3780686-3-dylany@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5e2151ff9 upstream.
__skb_get_hash_symmetric() was added to compute a symmetric hash over
the protocol, addresses and transport ports, by commit eb70db8756
("packet: Use symmetric hash for PACKET_FANOUT_HASH."). It uses
flow_keys_dissector_symmetric_keys as the flow_dissector to incorporate
IPv4 addresses, IPv6 addresses and ports. However, it should not specify
the flag as FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL, which stops further
dissection when an IPv6 flow label is encountered, making transport
ports not being incorporated in such case.
As a consequence, the symmetric hash is based on 5-tuple for IPv4 but
3-tuple for IPv6 when flow label is present. It caused a few problems,
e.g. when nft symhash and openvswitch l4_sym rely on the symmetric hash
to perform load balancing as different L4 flows between two given IPv6
addresses would always get the same symmetric hash, leading to uneven
traffic distribution.
Removing the use of FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL makes sure the
symmetric hash is based on 5-tuple for both IPv4 and IPv6 consistently.
Fixes: eb70db8756 ("packet: Use symmetric hash for PACKET_FANOUT_HASH.")
Reported-by: Lars Ekman <uablrek@gmail.com>
Closes: https://github.com/antrea-io/antrea/issues/5457
Signed-off-by: Quan Tian <qtian@vmware.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23970a1c94 upstream.
The clang build reports this error
fs/udf/inode.c:805:6: error: variable 'newblock' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (*err < 0)
^~~~~~~~
newblock is never set before error handling jump.
Initialize newblock to 0 and remove redundant settings.
Fixes: d8b39db5fab8 ("udf: Handle error when adding extent to a file")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20221230175341.1629734-1-trix@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d129640f upstream.
Local variable is definied first in the beginning of backlog_store(),
there is no need to define it again.
Fixes: 8c13ab115b ("md/bitmap: don't set max_write_behind if there is no write mostly device")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20230706083727.608914-2-yukuai1@huaweicloud.com
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d07fa1dd1 upstream.
The pipe cpumask used to serialize opens between the main and percpu
trace pipes is not zeroed or initialized. This can result in
spurious -EBUSY returns if underlying memory is not fully zeroed.
This has been observed by immediate failure to read the main
trace_pipe file on an otherwise newly booted and idle system:
# cat /sys/kernel/debug/tracing/trace_pipe
cat: /sys/kernel/debug/tracing/trace_pipe: Device or resource busy
Zero the allocation of pipe_cpumask to avoid the problem.
Link: https://lore.kernel.org/linux-trace-kernel/20230831125500.986862-1-bfoster@redhat.com
Cc: stable@vger.kernel.org
Fixes: c2489bb7e6 ("tracing: Introduce pipe_cpumask to avoid race on trace_pipes")
Reviewed-by: Zheng Yejian <zhengyejian1@huawei.com>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f7f984fa8 upstream.
Starting from SPR, the basic uncore PMON information is retrieved from
the discovery table (resides in an MMIO space populated by BIOS). It is
called the discovery method. The existing value of the type->num_boxes
is from the discovery table.
On some SPR variants, there is a firmware bug that makes the value from the
discovery table incorrect. We use the value from the
SPR_MSR_UNC_CBO_CONFIG MSR to replace the one from the discovery table:
38776cc45e ("perf/x86/uncore: Correct the number of CHAs on SPR")
Unfortunately, the SPR_MSR_UNC_CBO_CONFIG isn't available for the EMR
XCC (Always returns 0), but the above firmware bug doesn't impact the
EMR XCC.
Don't let the value from the MSR replace the existing value from the
discovery table.
Fixes: 38776cc45e ("perf/x86/uncore: Correct the number of CHAs on SPR")
Reported-by: Stephane Eranian <eranian@google.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Link: https://lore.kernel.org/r/20230905134248.496114-1-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d7d72a34e upstream.
On large enclaves we hit the softlockup warning with following call trace:
xa_erase()
sgx_vepc_release()
__fput()
task_work_run()
do_exit()
The latency issue is similar to the one fixed in:
8795359e35 ("x86/sgx: Silence softlockup detection when releasing large enclaves")
The test system has 64GB of enclave memory, and all is assigned to a single VM.
Release of 'vepc' takes a longer time and causes long latencies, which triggers
the softlockup warning.
Add cond_resched() to give other tasks a chance to run and reduce
latencies, which also avoids the softlockup detector.
[ mingo: Rewrote the changelog. ]
Fixes: 540745ddbc ("x86/sgx: Introduce virtual EPC for use by KVM guests")
Reported-by: Yu Zhang <yu.zhang@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Yu Zhang <yu.zhang@ionos.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Acked-by: Haitao Huang <haitao.huang@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59cf445754 upstream.
Commit 85d07c5562 ("USB: core: Unite old scheme and new scheme
descriptor reads") altered the way USB devices are enumerated
following detection, and in the process it messed up the
initialization of SuperSpeed (or faster) devices:
[ 31.650759] usb 2-1: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
[ 31.663107] usb 2-1: device descriptor read/8, error -71
[ 31.952697] usb 2-1: new SuperSpeed Plus Gen 2x1 USB device number 3 using xhci_hcd
[ 31.965122] usb 2-1: device descriptor read/8, error -71
[ 32.080991] usb usb2-port1: attempt power cycle
...
The problem was caused by the commit forgetting that in SuperSpeed or
faster devices, the device descriptor uses a logarithmic encoding of
the bMaxPacketSize0 value. (For some reason I thought the 255 case in
the switch statement was meant for these devices, but it isn't -- it
was meant for Wireless USB and is no longer needed.)
We can fix the oversight by testing for buf->bMaxPacketSize0 = 9
(meaning 512, the actual maxpacket size for ep0 on all SuperSpeed
devices) and straightening out the logic that checks and adjusts our
initial guesses of the maxpacket value.
Reported-and-tested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Closes: https://lore.kernel.org/linux-usb/20230810002257.nadxmfmrobkaxgnz@synopsys.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 85d07c5562 ("USB: core: Unite old scheme and new scheme descriptor reads")
Link: https://lore.kernel.org/r/8809e6c5-59d5-4d2d-ac8f-6d106658ad73@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff33299ec8 upstream.
Syzbot reported an out-of-bounds read in sysfs.c:read_descriptors():
BUG: KASAN: slab-out-of-bounds in read_descriptors+0x263/0x280 drivers/usb/core/sysfs.c:883
Read of size 8 at addr ffff88801e78b8c8 by task udevd/5011
CPU: 0 PID: 5011 Comm: udevd Not tainted 6.4.0-rc6-syzkaller-00195-g40f71e7cd3c6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106
print_address_description.constprop.0+0x2c/0x3c0 mm/kasan/report.c:351
print_report mm/kasan/report.c:462 [inline]
kasan_report+0x11c/0x130 mm/kasan/report.c:572
read_descriptors+0x263/0x280 drivers/usb/core/sysfs.c:883
...
Allocated by task 758:
...
__do_kmalloc_node mm/slab_common.c:966 [inline]
__kmalloc+0x5e/0x190 mm/slab_common.c:979
kmalloc include/linux/slab.h:563 [inline]
kzalloc include/linux/slab.h:680 [inline]
usb_get_configuration+0x1f7/0x5170 drivers/usb/core/config.c:887
usb_enumerate_device drivers/usb/core/hub.c:2407 [inline]
usb_new_device+0x12b0/0x19d0 drivers/usb/core/hub.c:2545
As analyzed by Khazhy Kumykov, the cause of this bug is a race between
read_descriptors() and hub_port_init(): The first routine uses a field
in udev->descriptor, not expecting it to change, while the second
overwrites it.
Prior to commit 45bf39f8df ("USB: core: Don't hold device lock while
reading the "descriptors" sysfs file") this race couldn't occur,
because the routines were mutually exclusive thanks to the device
locking. Removing that locking from read_descriptors() exposed it to
the race.
The best way to fix the bug is to keep hub_port_init() from changing
udev->descriptor once udev has been initialized and registered.
Drivers expect the descriptors stored in the kernel to be immutable;
we should not undermine this expectation. In fact, this change should
have been made long ago.
So now hub_port_init() will take an additional argument, specifying a
buffer in which to store the device descriptor it reads. (If udev has
not yet been initialized, the buffer pointer will be NULL and then
hub_port_init() will store the device descriptor in udev as before.)
This eliminates the data race responsible for the out-of-bounds read.
The changes to hub_port_init() appear more extensive than they really
are, because of indentation changes resulting from an attempt to avoid
writing to other parts of the usb_device structure after it has been
initialized. Similar changes should be made to the code that reads
the BOS descriptor, but that can be handled in a separate patch later
on. This patch is sufficient to fix the bug found by syzbot.
Reported-and-tested-by: syzbot+18996170f8096c6174d0@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000c0ffe505fe86c9ca@google.com/#r
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Khazhy Kumykov <khazhy@google.com>
Fixes: 45bf39f8df ("USB: core: Don't hold device lock while reading the "descriptors" sysfs file")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/b958b47a-9a46-4c22-a9f9-e42e42c31251@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de28e469da upstream.
The usb_get_device_descriptor() routine reads the device descriptor
from the udev device and stores it directly in udev->descriptor. This
interface is error prone, because the USB subsystem expects in-memory
copies of a device's descriptors to be immutable once the device has
been initialized.
The interface is changed so that the device descriptor is left in a
kmalloc-ed buffer, not copied into the usb_device structure. A
pointer to the buffer is returned to the caller, who is then
responsible for kfree-ing it. The corresponding changes needed in the
various callers are fairly small.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/d0111bb6-56c1-4f90-adf2-6cfe152f6561@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85d07c5562 upstream.
In preparation for reworking the usb_get_device_descriptor() routine,
it is desirable to unite the two different code paths responsible for
initially determining endpoint 0's maximum packet size in a newly
discovered USB device. Making this determination presents a
chicken-and-egg sort of problem, in that the only way to learn the
maxpacket value is to get it from the device descriptor retrieved from
the device, but communicating with the device to retrieve a descriptor
requires us to know beforehand the ep0 maxpacket size.
In practice this problem is solved in two different ways, referred to
in hub.c as the "old scheme" and the "new scheme". The old scheme
(which is the approach recommended by the USB-2 spec) involves asking
the device to send just the first eight bytes of its device
descriptor. Such a transfer uses packets containing no more than
eight bytes each, and every USB device must have an ep0 maxpacket size
>= 8, so this should succeed. Since the bMaxPacketSize0 field of the
device descriptor lies within the first eight bytes, this is all we
need.
The new scheme is an imitation of the technique used in an early
Windows USB implementation, giving it the happy advantage of working
with a wide variety of devices (some of them at the time would not
work with the old scheme, although that's probably less true now). It
involves making an initial guess of the ep0 maxpacket size, asking the
device to send up to 64 bytes worth of its device descriptor (which is
only 18 bytes long), and then resetting the device to clear any error
condition that might have resulted from the guess being wrong. The
initial guess is determined by the connection speed; it should be
correct in all cases other than full speed, for which the allowed
values are 8, 16, 32, and 64 (in this case the initial guess is 64).
The reason for this patch is that the old- and new-scheme parts of
hub_port_init() use different code paths, one involving
usb_get_device_descriptor() and one not, for their initial reads of
the device descriptor. Since these reads have essentially the same
purpose and are made under essentially the same circumstances, this is
illogical. It makes more sense to have both of them use a common
subroutine.
This subroutine does basically what the new scheme's code did, because
that approach is more general than the one used by the old scheme. It
only needs to know how many bytes to transfer and whether or not it is
being called for the first iteration of a retry loop (in case of
certain time-out errors). There are two main differences from the
former code:
We initialize the bDescriptorType field of the transfer buffer
to 0 before performing the transfer, to avoid possibly
accessing an uninitialized value afterward.
We read the device descriptor into a temporary buffer rather
than storing it directly into udev->descriptor, which the old
scheme implementation used to do.
Since the whole point of this first read of the device descriptor is
to determine the bMaxPacketSize0 value, that is what the new routine
returns (or an error code). The value is stored in a local variable
rather than in udev->descriptor. As a side effect, this necessitates
moving a section of code that checks the bcdUSB field for SuperSpeed
devices until after the full device descriptor has been retrieved.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/495cb5d4-f956-4f4a-a875-1e67e9489510@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f236433064 upstream.
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c97cd0b4b5 upstream.
When sending Discover Identity messages to a Port Partner that uses Power
Delivery v2 and SVDM v1, we currently send PD v2 messages with SVDM v2.0,
expecting the port partner to respond with its highest supported SVDM
version as stated in Section 6.4.4.2.3 in the Power Delivery v3
specification. However, sending SVDM v2 to some Power Delivery v2 port
partners results in a NAK whereas sending SVDM v1 does not.
NAK messages can be handled by the initiator (PD v3 section 6.4.4.2.5.1),
and one solution could be to resend Discover Identity on a lower SVDM
version if possible. But, Section 6.4.4.3 of PD v2 states that "A NAK
response Should be taken as an indication not to retry that particular
Command."
Instead, we can set the SVDM version to the maximum one supported by the
negotiated PD revision. When operating in PD v2, this obeys Section
6.4.4.2.3, which states the SVDM field "Shall be set to zero to indicate
Version 1.0." In PD v3, the SVDM field "Shall be set to 01b to indicate
Version 2.0."
Fixes: c34e85fa69 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230731165926.1815338-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e520d0b6be upstream.
Allocate extra space for terminating element at:
drivers/cpufreq/brcmstb-avs-cpufreq.c:
449 table[i].frequency = CPUFREQ_TABLE_END;
and add code comment to make this clear.
This fixes the following -Warray-bounds warning seen after building
ARM with multi_v7_defconfig (GCC 13):
In function 'brcm_avs_get_freq_table',
inlined from 'brcm_avs_cpufreq_init' at drivers/cpufreq/brcmstb-avs-cpufreq.c:623:15:
drivers/cpufreq/brcmstb-avs-cpufreq.c:449:28: warning: array subscript 5 is outside array bounds of 'void[60]' [-Warray-bounds=]
449 | table[i].frequency = CPUFREQ_TABLE_END;
In file included from include/linux/node.h:18,
from include/linux/cpu.h:17,
from include/linux/cpufreq.h:12,
from drivers/cpufreq/brcmstb-avs-cpufreq.c:44:
In function 'devm_kmalloc_array',
inlined from 'devm_kcalloc' at include/linux/device.h:328:9,
inlined from 'brcm_avs_get_freq_table' at drivers/cpufreq/brcmstb-avs-cpufreq.c:437:10,
inlined from 'brcm_avs_cpufreq_init' at drivers/cpufreq/brcmstb-avs-cpufreq.c:623:15:
include/linux/device.h:323:16: note: at offset 60 into object of size 60 allocated by 'devm_kmalloc'
323 | return devm_kmalloc(dev, bytes, flags);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -Warray-bounds.
Link: https://github.com/KSPP/linux/issues/324
Fixes: de322e0859 ("cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9c83f71ee upstream.
We were reading the length of the scatterlist sg after copying value of
tsg inside.
So we are using the size of the previous scatterlist and for the first
one we are using an unitialised value.
Fix this by copying tsg in sg[0] before reading the size.
Fixes : 8a1012d3f2 ("crypto: stm32 - Support for STM32 HASH module")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea5717cb13 upstream.
OS installers are relying on /sys/firmware/ipl/has_secure to be
present on machines supporting secure boot. This file is present
for all IPL types, but not the unknown type, which prevents a secure
installation when an LPAR is booted in HMC via FTP(s), because
this is an unknown IPL type in linux. While at it, also add the secure
file.
Fixes: c9896acc78 ("s390/ipl: Provide has_secure sysfs attribute")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
