commit 9c64e749ce upstream.
Set the segment size of the virtio_gpu device to the value
used by the drm helpers when allocating sg lists to fix the
following complaint from DMA_API debug code:
DMA-API: virtio-pci 0000:07:00.0: mapping sg segment longer than
device claims to support [len=262144] [max=65536]
Cc: stable@vger.kernel.org
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7258a4cc-da16-5c34-a042-2a23ee396d56@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8929f95b2b upstream.
This reverts commit c46bfba133 ("connector: Fix proc_event_num_listeners
count not cleared").
It is not accurate to reset proc_event_num_listeners according to
cn_netlink_send_mult() return value -ESRCH.
In the case of stress-ng netlink-proc, -ESRCH will always be returned,
because netlink_broadcast_filtered will return -ESRCH,
which may cause stress-ng netlink-proc performance degradation.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401112259.b23a1567-oliver.sang@intel.com
Fixes: c46bfba133 ("connector: Fix proc_event_num_listeners count not cleared")
Signed-off-by: Keqi Wang <wangkeqi_chris@163.com>
Link: https://lore.kernel.org/r/20240209091659.68723-1-wangkeqi_chris@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 917e9b7c23 upstream.
This reverts commit abe2023b4c.
Changing the locking order means that scheduler/msm_job_run() can race
with the recovery kthread worker, with the result that the GPU gets an
extra runpm get when we are trying to power it off. Leaving the GPU in
an unrecovered state.
I'll need to come up with a different scheme for appeasing lockdep.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/573835/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9163616853 upstream.
commit ab4750332d ("drm/amdgpu/sdma5.2: add begin/end_use ring
callbacks") caused GFXOFF control to be used more heavily and the
codepath that was removed from commit 0dee726395 ("drm/amd: flush any
delayed gfxoff on suspend entry") now can be exercised at suspend again.
Users report that by using GNOME to suspend the lockscreen trigger will
cause SDMA traffic and the system can deadlock.
This reverts commit 0dee726395.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Fixes: ab4750332d ("drm/amdgpu/sdma5.2: add begin/end_use ring callbacks")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 977fe773dc upstream.
This reverts commit 1a19755519.
This commit causes interrupts to be lost for FCoE devices, since it changed
sping locks from "bh" to "irqsave".
Instead, a work queue should be used, and will be addressed in a separate
commit.
Fixes: 1a19755519 ("scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock")
Signed-off-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/c578cdcd46b60470535c4c4a953e6a1feca0dffd.1707500786.git.lduncan@suse.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a107d643b2 upstream.
This reverts commit 85d2a31fe4.
The rkisp1 does share interrupt lines on some platforms, after all. Thus
we need to revert this, and implement a fix for the rkisp1 shared irq
handling in a follow-up patch.
Closes: https://lore.kernel.org/all/87o7eo8vym.fsf@gmail.com/
Link: https://lore.kernel.org/r/20231218-rkisp-shirq-fix-v1-1-173007628248@ideasonboard.com
Reported-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 337cebbd85 upstream.
Fastopen and PM-trigger subflow shutdown can race, as reported by
syzkaller.
In my first attempt to close such race, I missed the fact that
the subflow status can change again before the subflow_state_change
callback is invoked.
Address the issue additionally copying with all the states directly
reachable from TCP_FIN_WAIT1.
Fixes: 1e777f39b4 ("mptcp: add MSG_FASTOPEN sendmsg flag support")
Fixes: 4fd19a3070 ("mptcp: fix inconsistent state on fastopen race")
Cc: stable@vger.kernel.org
Reported-by: syzbot+c53d4d3ddb327e80bc51@syzkaller.appspotmail.com
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/458
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f012d796a6 upstream.
Before adding a new entry in mptcp_userspace_pm_get_local_id(), it's
better to check whether this address is already in userspace pm local
address list. If it's in the list, no need to add a new entry, just
return it's address ID and use this address.
Fixes: 8b20137012 ("mptcp: read attributes of addr entries managed by userspace PMs")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <geliang.tang@linux.dev>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 013e3179db upstream.
mptcp_rcv_space_init() is supposed to happen under the msk socket
lock, but active msk socket does that without such protection.
Leverage the existing mptcp_propagate_state() helper to that extent.
We need to ensure mptcp_rcv_space_init will happen before
mptcp_rcv_space_adjust(), and the release_cb does not assure that:
explicitly check for such condition.
While at it, move the wnd_end initialization out of mptcp_rcv_space_init(),
it never belonged there.
Note that the race does not produce ill effect in practice, but
change allows cleaning-up and defying better the locking model.
Fixes: a6b118febb ("mptcp: add receive buffer auto-tuning")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd70eb689 upstream.
Such field is there to avoid acquiring the data lock in a few spots,
but it adds complexity to the already non trivial locking schema.
All the relevant call sites (mptcp-level re-injection, set socket
options), are slow-path, drop such field in favor of 'cb_flags', adding
the relevant locking.
This patch could be seen as an improvement, instead of a fix. But it
simplifies the next patch. The 'Fixes' tag has been added to help having
this series backported to stable.
Fixes: e9d09baca6 ("mptcp: avoid atomic bit manipulation when possible")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdbef0a6ff upstream.
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
Export kill_wait() helper in userspace_pm.sh into mptcp_lib.sh and
rename it as mptcp_lib_kill_wait(). It can be used to instead of
kill_wait() in mptcp_join.sh. Use the new helper in both scripts.
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231128-send-net-next-2023107-v4-9-8d6b94150f6b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de46d138e7 upstream.
If a CI executes the same selftest multiple times with different
options, all results from the same subtests will have the same title,
which confuse the CI. With the same title printed in TAP, the tests are
considered as the same ones.
Now, it is possible to override this prefix by using MPTCP_LIB_KSFT_TEST
env var, and have a different title.
While at it, use 'basename' to remove the suffix as well instead of
using an extra 'sed'.
Fixes: c4192967e6 ("selftests: mptcp: lib: format subtests results in TAP")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-7-4c1c11e571ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d4dfb2019 upstream.
On very slow environments -- e.g. when QEmu is used without KVM --,
mptcp_join.sh selftest can take a bit more than 20 minutes. Bump the
default timeout by 50% as it seems normal to take that long on some
environments.
When a debug kernel config is used, this selftest will take even longer,
but that's certainly not a common test env to consider for the timeout.
The Fixes tag that has been picked here is there simply to help having
this patch backported to older stable versions. It is difficult to point
to the exact commit that made some env reaching the timeout from time to
time.
Fixes: d17b968b98 ("selftests: mptcp: increase timeout to 20 minutes")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-5-4c1c11e571ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d41f10fa4 upstream.
Since the commit mentioned below, 'mptcp_join' selftests is using
IPTables to add rules to the Mangle table, only in IPv4.
This KConfig is usually enabled by default in many defconfig, but we
recently noticed that some CI were running our selftests without them
enabled.
Fixes: b6e074e171 ("selftests: mptcp: add infinite map testcase")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-4-4c1c11e571ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c86fad2ce upstream.
Since the commit mentioned below, 'mptcp_join' selftests is using
IPTables to add rules to the Filter table for IPv6.
It is then required to have IP6_NF_FILTER KConfig.
This KConfig is usually enabled by default in many defconfig, but we
recently noticed that some CI were running our selftests without them
enabled.
Fixes: 523514ed0a ("selftests: mptcp: add ADD_ADDR IPv6 test cases")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-3-4c1c11e571ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3645c84490 upstream.
Since the commit mentioned below, 'mptcp_join' selftests is using
IPTables to add rules to the Filter table.
It is then required to have IP_NF_FILTER KConfig.
This KConfig is usually enabled by default in many defconfig, but we
recently noticed that some CI were running our selftests without them
enabled.
Fixes: 8d014eaa92 ("selftests: mptcp: add ADD_ADDR timeout test case")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c620dc43 upstream.
When the MPTCP PM detects that a subflow is stale, all the packet
scheduler must re-inject all the mptcp-level unacked data. To avoid
acquiring unneeded locks, it first try to check if any unacked data
is present at all in the RTX queue, but such check is currently
broken, as it uses TCP-specific helper on an MPTCP socket.
Funnily enough fuzzers and static checkers are happy, as the accessed
memory still belongs to the mptcp_sock struct, and even from a
functional perspective the recovery completed successfully, as
the short-cut test always failed.
A recent unrelated TCP change - commit d5fed5addb ("tcp: reorganize
tcp_sock fast path variables") - exposed the issue, as the tcp field
reorganization makes the mptcp code always skip the re-inection.
Fix the issue dropping the bogus call: we are on a slow path, the early
optimization proved once again to be evil.
Fixes: 1e1d9d6f11 ("mptcp: handle pending data on closed subflow")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/468
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-1-4c1c11e571ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a951884d82 ]
lld is now able to build ARMv4 and ARMv4T kernels, which means it can
generate thunks for those (__ARMv4PILongThunk_*, __ARMv4PILongBXThunk_*)
that can interfere with kallsyms table generation since they do not get
ignore like the corresponding ARMv5+ ones are:
Inconsistent kallsyms data
Try "make KALLSYMS_EXTRA_PASS=1" as a workaround
Replace the hardcoded list of thunk symbols with a more general regex that
covers this one along with future symbols that follow the same pattern.
Fixes: 5eb6e28043 ("ARM: 9289/1: Allow pre-ARMv5 builds with ld.lld 16.0.0 and newer")
Fixes: efe6e30680 ("kallsyms: fix nonconverging kallsyms table with lld")
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d9a16b2a4 ]
get_line() does not trim the leading spaces, but the
parse_source_files() expects to get lines with source files paths where
the first space occurs after the file path.
Fixes: 70f30cfe5b ("modpost: use read_text_file() and get_line() for reading text files")
Signed-off-by: Radek Krejci <radek.krejci@oracle.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c9d0f6f7 ]
According to the Intel datasheets, software must reset the block
buffer index twice for block process call transactions: once before
writing the outgoing data to the buffer, and once again before
reading the incoming data from the buffer.
The driver is currently missing the second reset, causing the wrong
portion of the block buffer to be read.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Piotr Zakowski <piotr.zakowski@intel.com>
Closes: https://lore.kernel.org/linux-i2c/20240213120553.7b0ab120@endymion.delvare/
Fixes: 315cd67c94 ("i2c: i801: Add Block Write-Block Read Process Call support")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f44bff1926 ]
On powerpc, it is possible to compile test both the new apple (arm) and
old pasemi (powerpc) drivers for the i2c hardware at the same time,
which leads to a warning about linking the same object file twice:
scripts/Makefile.build:244: drivers/i2c/busses/Makefile: i2c-pasemi-core.o is added to multiple modules: i2c-apple i2c-pasemi
Rework the driver to have an explicit helper module, letting Kbuild
take care of whether this should be built-in or a loadable driver.
Fixes: 9bc5f4f660 ("i2c: pasemi: Split pci driver to its own file")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1acb10950 ]
KASAN is seen to increase stack usage, to the point that it was reported
to lead to stack overflow on some 32-bit machines (see link).
To avoid overflows the stack size was doubled for KASAN builds in
commit 3e8635fb2e ("powerpc/kasan: Force thread size increase with
KASAN").
However with a 32KB stack size to begin with, the doubling leads to a
64KB stack, which causes build errors:
arch/powerpc/kernel/switch.S:249: Error: operand out of range (0x000000000000fe50 is not between 0xffffffffffff8000 and 0x0000000000007fff)
Although the asm could be reworked, in practice a 32KB stack seems
sufficient even for KASAN builds - the additional usage seems to be in
the 2-3KB range for a 64-bit KASAN build.
So only increase the stack for KASAN if the stack size is < 32KB.
Fixes: 18f14afe28 ("powerpc/64s: Increase default stack size to 32KB")
Reported-by: Spoorthy <spoorthy@linux.ibm.com>
Reported-by: Benjamin Gray <bgray@linux.ibm.com>
Reviewed-by: Benjamin Gray <bgray@linux.ibm.com>
Link: https://lore.kernel.org/linuxppc-dev/bug-207129-206035@https.bugzilla.kernel.org%2F/
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240212064244.3924505-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 846297e11e ]
Although the GICv3 code base has gained some handling of systems failing to
handle the shareability attributes, the GICv4 side of things has been
firmly ignored.
This is unfortunate, as the new recent addition of the "dma-noncoherent" is
supposed to apply to all of the GICR tables, and not just the ones that are
common to v3 and v4.
Add some checks to handle the VPROPBASE/VPENDBASE shareability and
cacheability attributes in the same way we deal with the other GICR_BASE
registers, wrapping the flag check in a helper for improved readability.
Note that this has been found by inspection only, as I don't have access to
HW that suffers from this particular issue.
Fixes: 3a0fff0fb6 ("irqchip/gic-v3: Enable non-coherent redistributors/ITSes DT probing")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20240213101206.2137483-2-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1c2765c6a ]
eiointc_domain_alloc() uses struct eiointc, which is not defined, for a
pointer. Older compilers treat that as a forward declaration and due to
assignment of a void pointer there is no warning emitted. As the variable
is then handed in as a void pointer argument to irq_domain_set_info() the
code is functional.
Use struct eiointc_priv instead.
[ tglx: Rewrote changelog ]
Fixes: dd281e1a1a ("irqchip: Add Loongson Extended I/O interrupt controller support")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20240130082722.2912576-2-maobibo@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83ef106fa7 ]
For i2c read operation in GSI mode, we are getting timeout
due to malformed TRE basically incorrect TRE sequence
in gpi(drivers/dma/qcom/gpi.c) driver.
I2C driver has geni_i2c_gpi(I2C_WRITE) function which generates GO TRE and
geni_i2c_gpi(I2C_READ)generates DMA TRE. Hence to generate GO TRE before
DMA TRE, we should move geni_i2c_gpi(I2C_WRITE) before
geni_i2c_gpi(I2C_READ) inside the I2C GSI mode transfer function
i.e. geni_i2c_gpi_xfer().
TRE stands for Transfer Ring Element - which is basically an element with
size of 4 words. It contains all information like slave address,
clk divider, dma address value data size etc).
Mainly we have 3 TREs(Config, GO and DMA tre).
- CONFIG TRE : consists of internal register configuration which is
required before start of the transfer.
- DMA TRE : contains DDR/Memory address, called as DMA descriptor.
- GO TRE : contains Transfer directions, slave ID, Delay flags, Length
of the transfer.
I2c driver calls GPI driver API to config each TRE depending on the
protocol.
For read operation tre sequence will be as below which is not aligned
to hardware programming guide.
- CONFIG tre
- DMA tre
- GO tre
As per Qualcomm's internal Hardware Programming Guide, we should configure
TREs in below sequence for any RX only transfer.
- CONFIG tre
- GO tre
- DMA tre
Fixes: d8703554f4 ("i2c: qcom-geni: Add support for GPI DMA")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5
Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cffe487026 ]
In this loop, we step through the buffer and after each item we check
if the size_left is greater than the minimum size we need. However,
the problem is that "bytes_left" is type ssize_t while sizeof() is type
size_t. That means that because of type promotion, the comparison is
done as an unsigned and if we have negative bytes left the loop
continues instead of ending.
Fixes: fe856be475 ("CIFS: parse and store info on iface queries")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78367c32be ]
Currently, GPIO_CTRL bits are set even if the pins are used for
measurements.
GPIO_CTRL bits should only be set if the pin is not used for
other functionality.
Fix this by only setting the GPIO_CTRL bits if the pin has no
other function.
Fixes: 62094060cf ("iio: adc: ad4130: add AD4130 driver")
Signed-off-by: Cosmin Tanislav <demonsingur@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240207132007.253768-2-demonsingur@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a22b0a2be6 ]
The clk_init_data struct does not have all its members
initialized, causing issues when trying to expose the internal
clock on the CLK pin.
Fix this by zero-initializing the clk_init_data struct.
Fixes: 62094060cf ("iio: adc: ad4130: add AD4130 driver")
Signed-off-by: Cosmin Tanislav <demonsingur@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240207132007.253768-1-demonsingur@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41044d5360 ]
The commit noted in fixes added a bogus requirement that runtime PM managed
devices need to be in the RPM_ACTIVE state for PME polling. In fact, only
devices in low power states should be polled.
However there's still a requirement that the device config space must be
accessible, which has implications for both the current state of the polled
device and the parent bridge, when present. It's not sufficient to assume
the bridge remains in D0 and cases have been observed where the bridge
passes the D0 test, but the PM state indicates RPM_SUSPENDING and config
space of the polled device becomes inaccessible during pci_pme_wakeup().
Therefore, since the bridge is already effectively required to be in the
RPM_ACTIVE state, formalize this in the code and elevate the PM usage count
to maintain the state while polling the subordinate device.
This resolves a regression reported in the bugzilla below where a
Thunderbolt/USB4 hierarchy fails to scan for an attached NVMe endpoint
downstream of a bridge in a D3hot power state.
Link: https://lore.kernel.org/r/20240123185548.1040096-1-alex.williamson@redhat.com
Fixes: d3fcd73603 ("PCI: Fix runtime PM race with PME polling")
Reported-by: Sanath S <sanath.s@amd.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218360
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Sanath S <sanath.s@amd.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a7aee9620 ]
In kasan_init_region, when k_start is not page aligned, at the begin of
for loop, k_cur = k_start & PAGE_MASK is less than k_start, and then
`va = block + k_cur - k_start` is less than block, the addr va is invalid,
because the memory address space from va to block is not alloced by
memblock_alloc, which will not be reserved by memblock_reserve later, it
will be used by other places.
As a result, memory overwriting occurs.
for example:
int __init __weak kasan_init_region(void *start, size_t size)
{
[...]
/* if say block(dcd97000) k_start(feef7400) k_end(feeff3fe) */
block = memblock_alloc(k_end - k_start, PAGE_SIZE);
[...]
for (k_cur = k_start & PAGE_MASK; k_cur < k_end; k_cur += PAGE_SIZE) {
/* at the begin of for loop
* block(dcd97000) va(dcd96c00) k_cur(feef7000) k_start(feef7400)
* va(dcd96c00) is less than block(dcd97000), va is invalid
*/
void *va = block + k_cur - k_start;
[...]
}
[...]
}
Therefore, page alignment is performed on k_start before
memblock_alloc() to ensure the validity of the VA address.
Fixes: 663c0c9496 ("powerpc/kasan: Fix shadow area set up for modules.")
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/1705974359-43790-1-git-send-email-xiaojiangfeng@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a038a3ff8c ]
MMU_FTR_USE_HIGH_BATS is set for G2_LE cores and derivatives like e300cX,
but the high BATs need to be enabled in HID2 to work. Add register
definitions and add the needed setup to __setup_cpu_603.
This fixes boot on CPUs like the MPC5200B with STRICT_KERNEL_RWX enabled
on systems where the flag has not been set by the bootloader already.
Fixes: e4d6654ebe ("powerpc/mm/32s: rework mmu_mapin_ram()")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240124103838.43675-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6442d79d88 ]
fw_devlink can detect most overlapping/intersecting cycles. However it was
missing a few corner cases because of an incorrect optimization logic that
tries to avoid repeating cycle detection for devices that are already
marked as part of a cycle.
Here's an example provided by Xu Yang (edited for clarity):
usb
+-----+
tcpc | |
+-----+ | +--|
| |----------->|EP|
|--+ | | +--|
|EP|<-----------| |
|--+ | | B |
| | +-----+
| A | |
+-----+ |
^ +-----+ |
| | | |
+-----| C |<--+
| |
+-----+
usb-phy
Node A (tcpc) will be populated as device 1-0050.
Node B (usb) will be populated as device 38100000.usb.
Node C (usb-phy) will be populated as device 381f0040.usb-phy.
The description below uses the notation:
consumer --> supplier
child ==> parent
1. Node C is populated as device C. No cycles detected because cycle
detection is only run when a fwnode link is converted to a device link.
2. Node B is populated as device B. As we convert B --> C into a device
link we run cycle detection and find and mark the device link/fwnode
link cycle:
C--> A --> B.EP ==> B --> C
3. Node A is populated as device A. As we convert C --> A into a device
link, we see it's already part of a cycle (from step 2) and don't run
cycle detection. Thus we miss detecting the cycle:
A --> B.EP ==> B --> A.EP ==> A
Looking at it another way, A depends on B in one way:
A --> B.EP ==> B
But B depends on A in two ways and we only detect the first:
B --> C --> A
B --> A.EP ==> A
To detect both of these, we remove the incorrect optimization attempt in
step 3 and run cycle detection even if the fwnode link from which the
device link is being created has already been marked as part of a cycle.
Reported-by: Xu Yang <xu.yang_2@nxp.com>
Closes: https://lore.kernel.org/lkml/DU2PR04MB8822693748725F85DC0CB86C8C792@DU2PR04MB8822.eurprd04.prod.outlook.com/
Fixes: 3fb16866b5 ("driver core: fw_devlink: Make cycle detection more robust")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240202095636.868578-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc9ceb90c4 ]
When irtoy_command fails, buf should be freed since it is allocated by
irtoy_tx, or there is a memleak.
Fixes: 4114978dcd ("media: ir_toy: prevent device from hanging during transmit")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24406f6794 ]
To ensure the interconnect votes are actually meaningful and in order to
prevent holding all buses at FMAX, introduce the sync state callback.
Fixes: e6f0d6a30f ("interconnect: qcom: Add SM8550 interconnect provider driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20231218-topic-8550_fixes-v1-2-ce1272d77540@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85e985a4f4 ]
The CO0 BCM needs to be up at all times, otherwise some hardware (like
the UFS controller) loses its connection to the rest of the SoC,
resulting in a hang of the platform, accompanied by a spectacular
logspam.
Mark it as keepalive to prevent such cases.
Fixes: 9c8c6bac1a ("interconnect: qcom: Add SC8180x providers")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231214-topic-sc8180_fixes-v1-1-421904863006@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61a348857e upstream.
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12783c0b9e upstream.
Currently, the function update_port_device_state gets the usb_hub from
udev->parent by calling usb_hub_to_struct_hub.
However, in case the actconfig or the maxchild is 0, the usb_hub would
be NULL and upon further accessing to get port_dev would result in null
pointer dereference.
Fix this by introducing an if check after the usb_hub is populated.
Fixes: 83cb2604f6 ("usb: core: add sysfs entry for usb device state")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240110095814.7626-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc509b6a47 upstream.
When power is recycled in usb controller during system power management,
the controller will recognize it and switch role if role has been changed
during power lost. In current design, it will be completed in resume()
function. However, this may bring issues since usb class devices have
their pm operations too and these device's resume() functions are still
not being called at this point. When usb controller recognized host role
should be stopped, these usb class devices will be removed at this point.
But these usb class devices can't be removed in some cases, such as scsi
devices. Since scsi driver may sync data to U-disk, however it will block
there because scsi drvier can only handle pm request when is in suspended
state. Therefore, there may exist a dependency between ci_resume() and usb
class device's resume(). To break this potential dependency, we need to
handle power lost work in a workqueue.
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240119123537.3614838-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2d2d7ea0d upstream.
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f17c34ffc7 upstream.
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2840143e39 upstream.
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3caf2b2ad7 upstream.
The ULPI per-device debugfs root is named after the ulpi device's
parent, but ulpi_unregister_interface tries to remove a debugfs
directory named after the ulpi device itself. This results in the
directory sticking around and preventing subsequent (deferred) probes
from succeeding. Change the directory name to match the ulpi device.
Fixes: bd0a0a024f ("usb: ulpi: Add debugfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240126223800.2864613-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9aed03a0a upstream.
Calling ->sync_write must be done while holding the PPM lock as
the mailbox logic does not support concurrent commands.
At least since the addition of partner task this means that
ucsi_acknowledge_connector_change should be called with the
PPM lock held as it calls ->sync_write.
Thus protect the only call to ucsi_acknowledge_connector_change
with the PPM. All other calls to ->sync_write already happen
under the PPM lock.
Fixes: b9aa02ca39 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 621c625712 upstream.
When als_capture_sample() is called with usage ID
HID_USAGE_SENSOR_TIME_TIMESTAMP, return 0. The HID sensor core ignores
the return value for capture_sample() callback, so return value doesn't
make difference. But correct the return value to return success instead
of -EINVAL.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240204125617.2635574-1-srinivas.pandruvada@linux.intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d6708bf0 upstream.
If a input device is opened before hid_hw_start is called, events may
not be received from the hardware. In the case of USB-backed devices,
for example, the hid_hw_start function is responsible for filling in
the URB which is submitted when the input device is opened. If a device
is opened prematurely, polling will never start because the device will
not have been in the correct state to send the URB.
Because the wacom driver registers its input devices before calling
hid_hw_start, there is a window of time where a device can be opened
and end up in an inoperable state. Some ARM-based Chromebooks in particular
reliably trigger this bug.
This commit splits the wacom_register_inputs function into two pieces.
One which is responsible for setting up the allocated inputs (and runs
prior to hid_hw_start so that devices are ready for any input events
they may end up receiving) and another which only registers the devices
(and runs after hid_hw_start to ensure devices can be immediately opened
without issue). Note that the functions to initialize the LEDs and remotes
are also moved after hid_hw_start to maintain their own dependency chains.
Fixes: 7704ac9373 ("HID: wacom: implement generic HID handling for pen generic devices")
Cc: stable@vger.kernel.org # v3.18+
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab41a31dd5 upstream.
The xf86-input-wacom driver does not treat '0' as a valid serial
number and will drop any input report which contains an
MSC_SERIAL = 0 event. The kernel driver already takes care to
avoid sending any MSC_SERIAL event if the value of serial[0] == 0
(which is the case for devices that don't actually report a
serial number), but this is not quite sufficient.
Only the lower 32 bits of the serial get reported to userspace,
so if this portion of the serial is zero then there can still
be problems.
This commit allows the driver to report either the lower 32 bits
if they are non-zero or the upper 32 bits otherwise.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
CC: stable@vger.kernel.org # v4.10
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00aab7dcb2 upstream.
A while back the I2C HID implementation was split in an ACPI and OF
part, but the new OF driver never initialises the client pointer which
is dereferenced on power-up failures.
Fixes: b33752c300 ("HID: i2c-hid: Reorganize so ACPI and OF are separate modules")
Cc: stable@vger.kernel.org # 5.12
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
