Add the ability to configure the RX/TX coalesce timer with ethtool.
Change default setting to scale with the clock rate rather than being a
fixed number of clock cycles.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that NAPI has been implemented, the hardware interrupt mitigation
mechanism is not needed to avoid excessive interrupt load in most cases.
Reduce the default RX interrupt threshold to 1 to reduce introduced
latency. This can be increased with ethtool if desired if some applications
still want to reduce interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement NAPI and GRO receive. In addition to better performance, this
also avoids handling RX packets in hard IRQ context, which reduces the
IRQ latency impact to other devices.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the RX or TX coalesce count is set to 1, there's no point in
setting the delay timer value since an interrupt will already be raised
on every packet, and the delay interrupt just causes extra pointless
interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the DMA error handling process, and remove some duplicated code
between the DMA error handling and the stop function.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using lp->ndev.parent to find the correct device to use for
DMA API calls, just use the dev attribute in the device structure.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a memory allocation error occurred during an attempt to refill a slot
in the RX ring after the packet was received, the hardware tail pointer
would still have been updated to point to or past the slot which remained
marked as previously completed. This would likely result in the DMA engine
raising an error when it eventually tried to use that slot again.
If a slot cannot be refilled, then just stop processing and do not move
the tail pointer past it. On the next attempt, we should skip receiving
the packet from the empty slot and just try to refill it again.
This failure mode has not actually been observed, but was found as part
of other driver updates.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luiz Angelo Daros de Luca says:
====================
net: dsa: realtek: add rtl8_4t tag
This patch series adds support for rtl8_4t tag. It is a variant of
rtl8_4 tag, with identical values but placed at the end of the packet
(before CRC).
It forces checksum in software before adding the tag as those extra
bytes at the end of the packet would be summed together with the rest of
the payload. When the switch removes the tag before sending the packet
to the network, that checksum will not match.
It might be useful to diagnose or avoid checksum offload issues. With an
ethertype tag like rtl8_4, the cpu port ethernet driver must work with
cksum_start and chksum_offset to correctly calculate checksums. If not,
the checksum field will be broken (it will contain the fake ip header
sum). In those cases, using 'rtl8_4t' might be an alternative way to
avoid checksum offload, either using runtime or device-tree property.
Regards,
Luiz
v4-v5)
- tags in alphabetical order in dsa_port.yaml
- remove ret var from rtl8365mb_change_tag_protocol
- Comment typos fixes
v3-v4)
- added rtl8_4 and rtl8_4t to dsa_port.yaml
- removed generic considerations about checksum problems with DSA tags.
They belong to Documentation/networking/dsa/dsa.rst
v2-v3)
- updated tag documentation (file header)
- do not remove position and format from rtl8365mb_cpu
- reinstate cpu to rtl8365mb
- moved rtl8365mb_change_tag_protocol after rtl8365mb_cpu_config
- do not modify rtl8365mb_cpu_config() logic
- remove cpu arg from rtl8365mb_cpu_config(); get it from priv
- dropped tag_protocol from rtl8365mb. It is now derived from
cpu->position.
- init cpu struct before dsa_register as default tag must be already
defined before dsa_register()
- fix formatting issues
v1-v2)
- remove mention to tail tagger, use trailing tagger.
- use void* instead of char* for pointing to tag beginning
- use memcpy to avoid problems with unaligned tags
- calculate checksum if it still pending
- keep in-use tag protocol in memory instead of reading from switch
register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The trailing tag is also supported by this family. The default is still
rtl8_4 but now the switch supports changing the tag to rtl8_4t.
Reintroduce the dropped cpu in struct rtl8365mb (removed by 6147631).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek switches supports the same tag both before ethertype or between
payload and the CRC.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek rtl8365mb DSA driver can use these two tag formats.
Cc: devicetree@vger.kernel.org
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Selftest refinements and a new test
Patches 1 and 11 improve the printed output of the mptcp_join.sh
selftest.
Patches 2-8 add a test for the MP_FASTCLOSE option, including
prerequisite changes like additional MPTCP MIBs.
Patches 9-10 add some groundwork for upcoming tests.
====================
Link: https://lore.kernel.org/r/20220304193636.219315-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch updated the output info of chk_rm_nr. Renamed 'sf' to 'rmsf',
which means 'remove subflow'. Added the display of whether the inverted
namespaces has been used to check the mib counters.
The new output looks like this:
002 remove multiple subflows syn[ ok ] - synack[ ok ] - ack[ ok ]
rm [ ok ] - rmsf [ ok ]
003 remove single address syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ]
rm [ ok ] - rmsf [ ok ] invert
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added five more arguments for chk_join_nr(). The default
values of them are all zero.
The first two, csum_ns1 and csum_ns1, are passed to chk_csum_nr(), to
check the mib counters of the checksum errors in ns1 and ns2. A '+'
can be added into this two arguments to represent that multiple
checksum errors are allowed when doing this check. For example,
chk_csum_nr "" +2 +2
indicates that two or more checksum errors are allowed in both ns1 and
ns2.
The remaining two, fail_nr and rst_nr, are passed to chk_fail_nr() and
chk_rst_nr() respectively, to check the sending and receiving mib
counters of MP_FAIL and MP_RST.
Also did some cleanups in chk_fail_nr(), renamed two local variables
and updated the output message.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the invert bytes check for the output data in
check_transfer().
Instead of the file mismatch error:
[ FAIL ] file received by server does not match (in, out):
-rw------- 1 root root 45643832 Jan 16 15:04 /tmp/tmp.9xpM6Paivv
Trailing bytes are:
MPTCP_TEST_FILE_END_MARKER
-rw------- 1 root root 45643832 Jan 16 15:04 /tmp/tmp.wnz1Yp4u7Z
Trailing bytes are:
MPTCP_TEST_FILE_END_MARKER
Print out the inverted bytes like this:
file received by server has inverted byte at 7454789
file received by server has inverted byte at 7454790
file received by server has inverted byte at 7454791
file received by server has inverted byte at 7454792
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the self test for MP_FASTCLOSE. Reused the argument
addr_nr_ns2 of do_transfer() to pass the extra arguments '-I 2' to
mptcp_connect commands. Then mptcp_connect disconnected the
connections to trigger the MP_FASTCLOSE sending and receiving. Used
chk_fclose_nr to check the MP_FASTCLOSE mibs and used chk_rst_nr to
check the MP_RST mibs. This test used the test_linkfail value to make
1024KB test files.
The output looks like this:
Created /tmp/tmp.XB8sfv1hJ0 (size 1024 KB) containing data sent by client
Created /tmp/tmp.RtTDbzqrXI (size 1024 KB) containing data sent by server
001 fastclose test syn[ ok ] - synack[ ok ] - ack[ ok ]
ctx[ ok ] - fclzrx[ ok ]
rtx[ ok ] - rstrx [ ok ] invert
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch reused the test_linkfail values above 2 to make test files with
the given sizes (KB) for both the client side and the server side. It's
useful for the test cases using different file sizes.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of using a global variable mptcp_connect, this patch added
a new local variable extra_args in do_transfer() to store the extra
arguments passing to the mptcp_connect commands.
This patch also renamed the speed level 'least' to 'speed_*'. This
more flexible way can avoid the need to add new speed levels in the
future.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added a new function chk_rst_nr() to check the numbers
of the MP_RST sending and receiving mibs.
Showed in the output whether the inverted namespaces check order is used.
Since if we pass -Cz to mptcp_join.sh, the MP_RST information is showed
twice.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added two more mibs for MP_RST, MPTCP_MIB_MPRSTTX for
the MP_RST sending and MPTCP_MIB_MPRSTRX for the MP_RST receiving.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added a new function chk_fclose_nr() to check the numbers
of the MP_FASTCLOSE sending and receiving mibs.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added two more mibs for MP_FASTCLOSE, MPTCP_MIB_MPFASTCLOSETX
for the MP_FASTCLOSE sending and MPTCP_MIB_MPFASTCLOSERX for receiving.
Also added a debug log for MP_FASTCLOSE receiving, printed out the recv_key
of MP_FASTCLOSE in mptcp_parse_option to show that MP_RST is received.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The number of self tests in mptcp_join.sh will soon be more than 100, the
output alignment is no longer OK. This patch adjusted it.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on
static allocation of IRQ resources in DT core code, this
causes an issue when using hierarchical interrupt domains
using "interrupts" property in the node as this bypassed
the hierarchical setup and messed up the irq chaining.
In preparation for removal of static setup of IRQ resource
from DT core code use platform_get_irq().
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Link: https://lore.kernel.org/r/20220303100815.25605-1-tangmeng@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variables 'res' inside the functions sparx5_ptp_get_1ppm and
sparx5_ptp_get_nominal_value was not initialized. So in case of the default
case of the switch after, it would return an uninitialized variable.
This makes also the clang builds to failed.
Fixes: 0933bd0404 ("net: sparx5: Add support for ptp clocks")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220304140918.3356873-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Add new PID/VID (0x13d3/0x3567) for MT7921
- Add new PID/VID (0x2550/0x8761) for Realtek 8761BU
- Add support for LG LGSBWAC02 (MT7663BUN)
- Add support for BCM43430A0 and BCM43430A1
- Add support for Intel Madison Peak (MsP2)
-----BEGIN PGP SIGNATURE-----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=2uvT
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2022-03-04' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add new PID/VID (0x13d3/0x3567) for MT7921
- Add new PID/VID (0x2550/0x8761) for Realtek 8761BU
- Add support for LG LGSBWAC02 (MT7663BUN)
- Add support for BCM43430A0 and BCM43430A1
- Add support for Intel Madison Peak (MsP2)
* tag 'for-net-next-2022-03-04' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (21 commits)
Bluetooth: btusb: Add another Realtek 8761BU
Bluetooth: hci_bcm: add BCM43430A0 & BCM43430A1
Bluetooth: use memset avoid memory leaks
Bluetooth: btmtksdio: Fix kernel oops when sdio suspend.
Bluetooth: btusb: Add a new PID/VID 13d3/3567 for MT7921
Bluetooth: move adv_instance_cnt read within the device lock
Bluetooth: hci_event: Add missing locking on hdev in hci_le_ext_adv_term_evt
Bluetooth: btusb: Make use of of BIT macro to declare flags
Bluetooth: Fix not checking for valid hdev on bt_dev_{info,warn,err,dbg}
Bluetooth: mediatek: fix the conflict between mtk and msft vendor event
Bluetooth: mt7921s: support bluetooth reset mechanism
Bluetooth: make array bt_uuid_any static const
Bluetooth: 6lowpan: No need to clear memory twice
Bluetooth: btusb: Improve stability for QCA devices
Bluetooth: btusb: add support for LG LGSBWAC02 (MT7663BUN)
Bluetooth: btusb: Add support for Intel Madison Peak (MsP2) device
Bluetooth: Improve skb handling in mgmt_device_connected()
Bluetooth: Fix skb allocation in mgmt_remote_name() & mgmt_device_connected()
Bluetooth: mgmt: Remove unneeded variable
Bluetooth: hci_sync: fix undefined return of hci_disconnect_all_sync()
...
====================
Link: https://lore.kernel.org/r/20220304193919.649815-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-03-04
We've added 32 non-merge commits during the last 14 day(s) which contain
a total of 59 files changed, 1038 insertions(+), 473 deletions(-).
The main changes are:
1) Optimize BPF stackmap's build_id retrieval by caching last valid build_id,
as consecutive stack frames are likely to be in the same VMA and therefore
have the same build id, from Hao Luo.
2) Several improvements to arm64 BPF JIT, that is, support for JITing
the atomic[64]_fetch_add, atomic[64]_[fetch_]{and,or,xor} and lastly
atomic[64]_{xchg|cmpxchg}. Also fix the BTF line info dump for JITed
programs, from Hou Tao.
3) Optimize generic BPF map batch deletion by only enforcing synchronize_rcu()
barrier once upon return to user space, from Eric Dumazet.
4) For kernel build parse DWARF and generate BTF through pahole with enabled
multithreading, from Kui-Feng Lee.
5) BPF verifier usability improvements by making log info more concise and
replacing inv with scalar type name, from Mykola Lysenko.
6) Two follow-up fixes for BPF prog JIT pack allocator, from Song Liu.
7) Add a new Kconfig to allow for loading kernel modules with non-matching
BTF type info; their BTF info is then removed on load, from Connor O'Brien.
8) Remove reallocarray() usage from bpftool and switch to libbpf_reallocarray()
in order to fix compilation errors for older glibc, from Mauricio Vásquez.
9) Fix libbpf to error on conflicting name in BTF when type declaration
appears before the definition, from Xu Kuohai.
10) Fix issue in BPF preload for in-kernel light skeleton where loaded BPF
program fds prevent init process from setting up fd 0-2, from Yucong Sun.
11) Fix libbpf reuse of pinned perf RB map when max_entries is auto-determined
by libbpf, from Stijn Tintel.
12) Several cleanups for libbpf and a fix to enforce perf RB map #pages to be
non-zero, from Yuntao Wang.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (32 commits)
bpf: Small BPF verifier log improvements
libbpf: Add a check to ensure that page_cnt is non-zero
bpf, x86: Set header->size properly before freeing it
x86: Disable HAVE_ARCH_HUGE_VMALLOC on 32-bit x86
bpf, test_run: Fix overflow in XDP frags bpf_test_finish
selftests/bpf: Update btf_dump case for conflicting names
libbpf: Skip forward declaration when counting duplicated type names
bpf: Add some description about BPF_JIT_ALWAYS_ON in Kconfig
bpf, docs: Add a missing colon in verifier.rst
bpf: Cache the last valid build_id
libbpf: Fix BPF_MAP_TYPE_PERF_EVENT_ARRAY auto-pinning
bpf, selftests: Use raw_tp program for atomic test
bpf, arm64: Support more atomic operations
bpftool: Remove redundant slashes
bpf: Add config to allow loading modules with BTF mismatches
bpf, arm64: Feed byte-offset into bpf line info
bpf, arm64: Call build_prologue() first in first JIT pass
bpf: Fix issue with bpf preload module taking over stdout/stdin of kernel.
bpftool: Bpf skeletons assert type sizes
bpf: Cleanup comments
...
====================
Link: https://lore.kernel.org/r/20220304164313.31675-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the compatible for BCM43430A0 bluetooth used in lg-lenok and
BCM43430A1 used in asus-sparrow.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use memset to initialize structs to prevent memory leaks
in l2cap_ecred_connect
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The field adv_instance_cnt is always accessed within a device lock,
except in the function add_advertising. A concurrent remove of an
advertisement with adding another one could result in the if check
"if a new instance was actually added" to not trigger, resulting
in not triggering the "advertising added event".
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both hci_find_adv_instance and hci_remove_adv_instance have a comment
above their function definition saying that these two functions require
the caller to hold the hdev->lock lock. However, hci_le_ext_adv_term_evt
does not acquire that lock and neither does its caller hci_le_meta_evt
(hci_le_meta_evt calls hci_le_ext_adv_term_evt via an indirect function
call because of the lookup in hci_le_ev_table).
The other event handlers all acquire and release the hdev->lock and they
follow the rule that hci_find_adv_instance and hci_remove_adv_instance
must be called while holding the hdev->lock lock.
The solution is to make sure hci_le_ext_adv_term_evt also acquires and
releases the hdev->lock lock. The check on ev->status which logs a
warning and does an early return is not covered by the lock because
other functions also access ev->status without holding the lock.
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes use of BIT macro when declaring BTUSB flags which makes it
understand how many bits are in use and many are left.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes attemting to print hdev->name directly which causes them to
print an error:
kernel: read_version:367: (efault): sock 000000006a3008f2
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a conflict between MediaTek wmt event and msft vendor extension
logic in the core layer since 145373cb1b ("Bluetooth: Add framework for
Microsoft vendor extension") was introduced because we changed the type of
mediatek wmt event to the type of msft vendor event in the driver.
But the purpose we reported mediatek event to the core layer is for the
diagnostic purpose with that we are able to see the full packet trace via
monitoring socket with btmon. Thus, it is harmless we keep the original
type of mediatek vendor event here to avoid breaking the msft extension
function especially they can be supported by Mediatek chipset like MT7921
, MT7922 devices and future devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement .cmd_timeout to reset the MT7921s device via a dedicated GPIO
pin when the firmware hang or the command has no response.
Co-developed-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chih-Ying Chiang <chih-yin.chiang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't populate the read-only array bt_uuid_any on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
'peer_addr' is a structure embedded in 'struct lowpan_peer'. So there is no
need to explicitly call memset(0) on it. It is already zeroed by kzalloc()
when 'peer' is allocated.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN6855 2.1 will reset to apply firmware downloaded, so wait
a moment for reset done then go ahead to improve stability.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce eir_skb_put_data() that can be used to simplify
operations on eir in goal of eliminating the necessity of intermediary
buffers.
eir_skb_put_data() is in pair to what eir_append_data() does with help of
eir_len, but without awkwardness when passing return value to skb_put() (as
it returns updated offset not size).
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch fixes skb allocation, as lack of space for ev might push skb
tail beyond its end.
Also introduce eir_precalc_len() that can be used instead of magic
numbers for similar eir operations on skb.
Fixes: cf1bce1de7 ("Bluetooth: mgmt: Make use of mgmt_send_event_skb in MGMT_EV_DEVICE_FOUND")
Fixes: e96741437e ("Bluetooth: mgmt: Make use of mgmt_send_event_skb in MGMT_EV_DEVICE_CONNECTED")
Signed-off-by: Angela Czubak <acz@semihalf.com>
Signed-off-by: Marek Maslanka <mm@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Return value from mgmt_cmd_complete() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
clang static analysis reports this problem
hci_sync.c:4428:2: warning: Undefined or garbage value
returned to caller
return err;
^~~~~~~~~~
If there are no connections this function is a noop but
err is never set and a false error could be reported.
Return 0 as other hci_* functions do.
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members" for these cases. The older
style of one-element or zero-length arrays should no longer be used.
Reference:
https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since the starting value in the for loop is greater than or equal to 1,
the restriction is CAS_FLAG_REG_PLUS is in the file cassini.h is
defined as 0x1 by macro, and the for loop and if condition is not
satisfied, so the code here is redundant.
Clean up the following smatch warning:
drivers/net/ethernet/sun/cassini.c:3513 cas_start_dma() warn: we never
enter this loop.
drivers/net/ethernet/sun/cassini.c:1239 cas_init_rx_dma() warn: we never
enter this loop.
drivers/net/ethernet/sun/cassini.c:1247 cas_init_rx_dma() warn: we never
enter this loop.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
