It has been observed that Toshiba DT01ACA family drives have
WRITE FPDMA QUEUED command timeouts and sometimes just freeze until
power-cycled under heavy write loads when their temperature is getting
polled in SCT mode. The SMART mode seems to be fine, though.
Let's make sure we don't use SCT mode for these drives then.
While only the 3 TB model was actually caught exhibiting the problem let's
play safe here to avoid data corruption and extend the ban to the whole
family.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Link: https://lore.kernel.org/r/0cb2e7022b66c6d21d3f189a12a97878d0e7511b.1595075458.git.mail@maciej.szmigiero.name
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMATCH detected a potential buffer overflow in the manipulation of
hwmon_attributes array inside the scmi_hwmon_probe function:
drivers/hwmon/scmi-hwmon.c:226
scmi_hwmon_probe() error: buffer overflow 'hwmon_attributes' 6 <= 9
Fix it by statically declaring the size of the array as the maximum
possible as defined by hwmon_max define.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20200715121338.GA18761@e119603-lin.cambridge.arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stefan Dietrich reports invalid temperature source messages on Asus Formula
XII Z490.
nct6775 nct6775.656: Invalid temperature source 28 at index 0,
source register 0x100, temp register 0x73
Debugging suggests that temperature source 28 reports the CPU temperature.
Let's assume that temperature sources 28 and 29 reflect "PECI Agent {0,1}
Calibration", similar to other chips of the series.
Reported-by: Stefan Dietrich <roots@gmx.de>
Cc: Stefan Dietrich <roots@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Issue:
When PEC is enabled, binding adm1272 to the adm1275 would
fail due to PEC error. See below:
adm1275: probe of xxxx failed with error -74
Diagnosis:
Per the datasheet of adm1272, adm1278, adm1293 and amd1294,
PMON_CONFIG (0xd4) is 16bits wide. On the other hand,
PMON_CONFIG (0xd4) for adm1275 is 8bits wide. The driver should not
assume everything is 8bits wide and read only 8bits from it.
Solution:
If it is adm1272, adm1278, adm1293 and adm1294, use i2c_read_word.
Else, use i2c_read_byte
Testing:
Binding adm1272 to the driver.
The change is only tested on adm1272.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20200709040612.3977094-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch fixes a bug which does not let FAN mode to be changed from
sysfs(pwm1_enable). i.e pwm1_enable can not be set to 3, it will always
remain at 0.
This is caused because the device driver handles the result of
"read_u8_from_i2c(client, REG_FAN_CONF1, &conf_reg)" incorrectly. The
driver thinks an error has occurred if the (result != 0). This has been
fixed by changing the condition to (result < 0).
Signed-off-by: Vishwas M <vishwas.reddy.vr@gmail.com>
Link: https://lore.kernel.org/r/20200707142747.118414-1-vishwas.reddy.vr@gmail.com
Fixes: 9df7305b5a ("hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The energy counters of certain models seems to be reporting
inconsistent values. Hence, match for the supported models.
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Fixes: 8abee9566b ("hwmon: Add amd_energy driver to report energy counters")
Link: https://lore.kernel.org/r/20200706171715.124993-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
aspeed_create_fan() reads a pwm_port value using of_property_read_u32().
If pwm_port will be more than ARRAY_SIZE(pwm_port_params), there will be
a buffer overflow in
aspeed_create_pwm_port()->aspeed_set_pwm_port_enable(). The patch fixes
the potential buffer overflow.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20200703111518.9644-1-novikov@ispras.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix a typo in SENSORS_IR35221 option: module name should be "ir35221"
instead of "ir35521".
Fixes: 8991ebd9c9 ("hwmon: (pmbus) Add client driver for IR35221")
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200702221349.18139-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Although it rarely happens, we should call free_capabilities()
if error happens after read_capabilities() to free allocated strings.
Fixes: de584afa5e ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Link: https://lore.kernel.org/r/20200625043242.31175-1-misono.tomohiro@jp.fujitsu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per the datasheet for max6697, OVERT mask and ALERT mask are different.
For example, the 7th bit of OVERT is the local channel but for alert
mask, the 6th bit is the local channel. Therefore, we can't apply the
same mask for both registers. In addition to that, the max6697 driver
is supposed to be compatibale with different models. I manually went over
all the listed chips and made sure all chip types have the same layout.
Testing;
mask value of 0x9 should map to 0x44 for ALERT and 0x84 for OVERT.
I used iotool to read the reg value back to verify. I only tested this
change on max6581.
Reference:
https://datasheets.maximintegrated.com/en/ds/MAX6581.pdfhttps://datasheets.maximintegrated.com/en/ds/MAX6697.pdfhttps://datasheets.maximintegrated.com/en/ds/MAX6699.pdf
Signed-off-by: Chu Lin <linchuyuan@google.com>
Fixes: 5372d2d71c ("hwmon: Driver for Maxim MAX6697 and compatibles")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
added support for multi-phase pmbus devices. However, when calling
pmbus_add_sensor() for fans, the patch swapped the `page` and `reg`
attributes. As a result, the fan speeds were reported as 0 RPM on my device.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Fixes: 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
Cc: stable@vger.kernel.org # v5.7+
Link: https://lore.kernel.org/r/449bc9e6c0e4305581e45905ce9d043b356a9932.1592904387.git.jan.kundrat@cesnet.cz
[groeck: Fixed references to offending commit]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Clang-based kernel building with W=1 warns that some static const
variables are unused:
drivers/hwmon/bt1-pvt.c:67:30: warning: unused variable 'poly_temp_to_N' [-Wunused-const-variable]
static const struct pvt_poly poly_temp_to_N = {
^
drivers/hwmon/bt1-pvt.c:99:30: warning: unused variable 'poly_volt_to_N' [-Wunused-const-variable]
static const struct pvt_poly poly_volt_to_N = {
^
Indeed these polynomials are utilized only when the PVT sensor alarms are
enabled. In that case they are used to convert the temperature and
voltage alarm limits from normal quantities (Volts and degree Celsius) to
the sensor data representation N = [0, 1023]. Otherwise when alarms are
disabled the driver only does the detected data conversion to the human
readable form and doesn't need that polynomials defined. So let's mark the
Temp-to-N and Volt-to-N polynomials with __maybe_unused attribute.
Note gcc with W=1 doesn't notice the problem.
Fixes: 87976ce282 ("hwmon: Add Baikal-T1 PVT sensor driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200603000753.391-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
to fixup conflicts in arch/x86/kernel/cpu/mce/core.c so MCE specific follow
up patches can be applied without creating a horrible merge conflict
afterwards.
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.
The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.
The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For hwmon drivers using the hwmon_device_register_with_info() API, it
is desirable to have a generic notification mechanism available. This
mechanism can be used to notify userspace as well as the thermal
subsystem if the driver experiences any events, such as warning or
critical alarms.
Implement hwmon_notify_event() to provide this mechanism. The function
generates a sysfs event and a udev event. If the device is registered
with the thermal subsystem and the event is associated with a temperature
sensor, also notify the thermal subsystem that a thermal event occurred.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building this driver with "clang -O3" produces a link error
after the compiler partially unrolls the loop and 256ms
becomes a compile-time constant that triggers the check
in udelay():
ld.lld: error: undefined symbol: __bad_udelay
>>> referenced by applesmc.c
>>> hwmon/applesmc.o:(read_smc) in archive drivers/built-in.a
I can see no reason against using a sleeping function here,
as no part of the driver runs in atomic context, so instead use
usleep_range() with a wide range and use jiffies for the
end condition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200527135207.1118624-1-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The timeout module parameter should not be used for setting the default
timeout. Because, if you set the timeout = 0, the default timeout will
be meaningless. And the timeout module parameter of 0 means "no timeout
module parameter specified".
Signed-off-by: Yuechao Zhao <yuechao.zhao@advantech.com.cn>
Link: https://lore.kernel.org/r/1590560219-41328-1-git-send-email-yuechao.zhao@advantech.com.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for retrieving Tdie and Tctl on AMD Renoir (4000-series
Ryzen CPUs).
It appears SMU offsets for reading current/voltage and CCD temperature
have changed for this generation (reads from currently used offsets
yield zeros), so those features cannot be enabled so trivially.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200510204842.2603-3-amonakov@ispras.ru
This patch adds hwmon based amd_energy driver support for
family 17h processors from AMD.
The driver provides following interface to the userspace
1. Reports the per core consumption
* file: "energy%d_input", label: "Ecore%03d"
2. Reports per socket energy consumption
* file: "energy%d_input", label: "Esocket%d"
3. To, increase the wrap around time of the socket energy
counters, a 64bit accumultor is implemented.
4. Reports scaled energy value in Joules.
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200519155011.56184-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Maxim MAX6654 to the lm90 driver.
The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: Josh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: zhouchuangao <zhouchuangao@xiaomi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16601 is a VR13.HC Dual-Output Voltage Regulator Chipset,
implementing a (8+1) multiphase synchronous buck converter.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'currpage' and 'currphase' variables in struct pmbus_data are used by
the PMBus core to determine if the phase or page value has changed. Both
are initialized with values which are never expected to be set in the code
to ensure that the first page/phase write operation is actually performed.
This is not well explained and occasionally causes confusion. Change the
type of both variables to s16 and initialize with -1 to ensure that the
initial value never matches a requested value, and clarify that this
value means "unknown/unset".
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
My 'pengutronix' address is defunct for years. Merge the entries and use
the proper contact address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200502142700.19254-1-wsa@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Check/fix all warnings generated by checkpatch.pl script on LM75 driver.
Signed-off-by: Michal Orzel <michalorzel.eng@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reduce indentation level in __hwmon_device_register() by preparing a
helper function.
This just improves code readability. No functional change.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Implement alert functions for INA226, INA230 and INA231. Expose 06h
Mask/Enable and 07h Alert Limit registers via alert setting and alarm
files.
Signed-off-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit adds support for lm70 commpatible drivers with systems that
use ACPI.
Signed-off-by: Andrej Picej <andpicej@gmail.com>
[groeck: Fix various issues seen if CONFIG_ACPI=n]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, each new XPS has to be added manually for module autoloading
to work. Since fan multiplier autodetection should work fine on all XPS
models, just match them all with one block like is done for Precision
and Studio.
The only match we replace that doesn't already use autodetection is
"XPS13" which, according to Google, only matches the XPS 13 9333. (All
other XPS 13 models have "XPS" as its own word, surrounded by spaces.)
According to the thread at [1], autodetection works for the XPS 13 9333,
meaning this shouldn't regress it. I do not own one to confirm with,
though.
Tested on an XPS 13 9350 and confirmed the module now autoloads and
reports reasonable-looking data. I am using BIOS 1.12.2 and do not see
any freezes when querying fan speed.
[1] https://lore.kernel.org/patchwork/patch/525367/
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/5d7e498b83e89ce7c41a449b61919c65d0770b73.1586033337.git.tommyhebb@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Gateworks System Controller has a hwmon sub-component that exposes
up to 16 ADC's, some of which are temperature sensors, others which are
voltage inputs. The ADC configuration (register mapping and name) is
configured via device-tree and varies board to board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When tsi-as-adc is configured it is possible for in7[0123]_input read to
return an incorrect value if a concurrent read to in[456]_input is
performed. This is caused by a concurrent manipulation of the mux
channel without proper locking as hwmon and mfd use different locks for
synchronization.
Switch hwmon to use the same lock as mfd when accessing the TSI channel.
Fixes: 4f16cab19a ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Samu Nuutamo <samu.nuutamo@vincit.fi>
[rebase to current master, reword commit message slightly]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The format of temperature limitation registers are 8-bit 2's complement
and the range is -128~127.
Converts the reading value to signed char to fix the incorrect range
of temperature limitation registers.
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When nct7904 power up, it compares current sensor readings against the
default threshold immediately. This results in false alarms on startup.
Read all SMI status registers in probe function to clear the alarms.
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
[groeck: Reworded description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If SCT is supported but SCT data tables are not, the driver unnecessarily
tries to fall back to SMART. Use SCT without data tables instead in this
situation.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The jc42 driver passes I2C client's name as hwmon device name. In case
of device tree probed devices this ends up being part of the compatible
string, "jc-42.4-temp". This name contains hyphens and the hwmon core
doesn't like this:
jc42 2-0018: hwmon: 'jc-42.4-temp' is not a valid name attribute, please fix
This changes the name to "jc42" which doesn't have any illegal
characters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200417092853.31206-1-s.hauer@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix the following sparse warning:
drivers/hwmon/k10temp.c:189:12: warning: symbol 'k10temp_temp_label' was
not declared. Should it be static?
drivers/hwmon/k10temp.c:202:12: warning: symbol 'k10temp_in_label' was
not declared. Should it be static?
drivers/hwmon/k10temp.c:207:12: warning: symbol 'k10temp_curr_label' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200409084502.42126-1-yanaijie@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Holger Hoffstätte observed that Samsung 850 Pro may return invalid
temperatures for a short period of time after resume. Return -ENODATA
to userspace if this is observed.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The addition of the support for reading the temperature of ATA drives as
per commit 5b46903d8b ("hwmon: Driver for disk and solid state drives
with temperature sensors") lists in the respective Kconfig section the
name of the module to be optionally built as "satatemp".
However, building the kernel modules with "CONFIG_SENSORS_DRIVETEMP=m",
does not generate a file named "satatemp.ko".
Instead, the rest of the original commit uses the term "drivetemp" and
a file named "drivetemp.ko" ends up in the kernel's modules directory.
This file has the right ingredients:
$ strings /path/to/drivetemp.ko | grep ^description
description=Hard drive temperature monitor
and modprobing it produces the expected result:
# drivetemp is not loaded
$ sensors -u drivetemp-scsi-4-0
Specified sensor(s) not found!
$ sudo modprobe drivetemp
$ sensors -u drivetemp-scsi-4-0
drivetemp-scsi-4-0
Adapter: SCSI adapter
temp1:
temp1_input: 35.000
temp1_max: 60.000
temp1_min: 0.000
temp1_crit: 70.000
temp1_lcrit: -40.000
temp1_lowest: 20.000
temp1_highest: 36.000
Fix Kconfig by referring to the true name of the module.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Ann T Ropea <bedhanger@gmx.de>
Link: https://lore.kernel.org/r/20200406235521.185309-1-bedhanger@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C chip IDs need to reflect chip names, not chip functionality.
Fixes: f621d61fd5 ("hwmon: (pmbus) add support for 2nd Gen Renesas digital multiphase")
Cc: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For security reasons I stopped using gmail account and kernel address is
now up-to-date alias to my personal address.
People periodically send me emails to address which they found in source
code of drivers, so this change reflects state where people can contact
me.
[ Added .mailmap entry as per Joe Perches - Linus ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200307104237.8199-1-pali@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131509.859324598@linutronix.de
There is an additional CCIN for the IBM CFFPS that may be classifed as
either version one or version two, based upon the rest of the bits of
the CCIN. Add support for it in the version detection.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1583948590-17220-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
