This driver uses mktime() and rtc_time_to_tm() to convert between time
values. This works fine on 64-bit kernels over the whole supported
range, and the vr41xx chip is a 64-bit MIPS implementation, but it is
inconsistent because it doesn't do the same thing on 32-bit kernels that
overflow in 2106 or 2038.
Changing it to use mktime64/rtc_time64_to_tm() should have no visible
impact on vr41xx but gets us closer to removing the 32-bit interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The SC27xx RTC can support dates from 1970-01-01 00:00:00 to 2149-06-06
23:59:59.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This is a preparation patch, changing to use devm_rtc_allocate_device()
that can allow driver to set 'range_max' and 'range_min' for the RTC
device.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com> (for zynqmp)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use ACPI for RTC Alarm only for Intel platforms
1. with Low Power S0 support
2. with HPET RTC emulation enabled
3. no earlier than 2015
Note that, during the test, it is found that this patch
1. works in 4.15-rc kernel
2. hangs the platform after suspend-to-idle for 2 or 3 times, in 4.15.0
3. works again in 4.16-rc3 kernel.
4. works in the latest 4.15.12 stable kernel.
Thus although this patch breaks 4.15.0 kernel for some unknown reason,
still, it is safe for both upstream and backport.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Previously, the RTC alarm is acknowledged either by the cmos rtc irq
handler, or by the hpet rtc irq handler.
When using ACPI RTC Fixed event as the RTC alarm, the RTC alarm is
acknowledged by the ACPI RTC event handler, as addressed in the previous
patch.
But, when resume from suspend-to-ram (ACPI S3), the ACPI SCI is cleared
right after resume, thus the ACPI RTC event handler is not invoked at all,
results in the RTC Alarm unacknowledged.
Handle this by comparing the current time and the RTC Alarm time in the
rtc_cmos driver .resume() callback
1. Assume the wakeup event has already been fired if the RTC Alarm time
is earlier than/equal to the current time, and ACK the RTC Alarm.
2. Assume the wakeup event has not been fired if the RTC Alarm time
is later than current time, and re-arm it if needed.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It's found that the HPET timer prevents the platform from entering
Low Power S0 on some new Intel platforms.
This means that
1. users can still use RTC wake Alarm for suspend-to-idle, but the system
never enters Low Power S0, which is a waste of power.
or
2. if users want to put the system into Low Power S0, they can not use
RTC as the wakeup source.
To fix this, we need to stop using the HPET timer for wake alarm.
But disabling CONFIG_HPET_EMULATE_RTC is not an option because HPET
emulates PIT at the same time, and this is needed on some of these
platforms.
Thus, introduce a new mode (use_acpi_alarm) to the rtc_cmos driver,
so that, even with CONFIG_HPET_EMULATE_RTC enabled, it's still possible to
use ACPI SCI for RTC Alarm, including UIE/AIE/wkalrm, instead of HPET.
Only necessary changes are made for the new "use_acpi_alarm" mode, including
1. drop all the calls to HPET emulation code, including the HPET irq
handler for rtc interrupt.
2. enabling/disabling ACPI RTC Fixed event upon RTC UIE/AIE request.
3. acknowledge the RTC Alarm in ACPI RTC Fixed event handler.
There is no functional change made in this patch if the new mode is not
enabled.
Note: this "use_acpi_alarm" mode is made based on the assumption that
ACPI RTC Fixed event is reliable both at runtime and during system wakeup.
And this has been verified on a couple of platforms I have, including
a MS Surface Pro 4 (SKL), a Lenovo Yoga 900 (SKL), and a HP 9360 (KBL).
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
-----BEGIN PGP SIGNATURE-----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=I0y0
-----END PGP SIGNATURE-----
Merge tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"We have queued a few more fixes (error handling, log replay,
softlockup) and the rest is SPDX updates that touche almost all files
so the diffstat is long"
* tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Only check first key for committed tree blocks
btrfs: add SPDX header to Kconfig
btrfs: replace GPL boilerplate by SPDX -- sources
btrfs: replace GPL boilerplate by SPDX -- headers
Btrfs: fix loss of prealloc extents past i_size after fsync log replay
Btrfs: clean up resources during umount after trans is aborted
btrfs: Fix possible softlock on single core machines
Btrfs: bail out on error during replay_dir_deletes
Btrfs: fix NULL pointer dereference in log_dir_items
-----BEGIN PGP SIGNATURE-----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=Ah5z
-----END PGP SIGNATURE-----
Merge tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"SMB3 fixes, a few for stable, and some important cleanup work from
Ronnie of the smb3 transport code"
* tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: change validate_buf to validate_iov
cifs: remove rfc1002 hardcoded constants from cifs_discard_remaining_data()
cifs: Change SMB2_open to return an iov for the error parameter
cifs: add resp_buf_size to the mid_q_entry structure
smb3.11: replace a 4 with server->vals->header_preamble_size
cifs: replace a 4 with server->vals->header_preamble_size
cifs: add pdu_size to the TCP_Server_Info structure
SMB311: Improve checking of negotiate security contexts
SMB3: Fix length checking of SMB3.11 negotiate request
CIFS: add ONCE flag for cifs_dbg type
cifs: Use ULL suffix for 64-bit constant
SMB3: Log at least once if tree connect fails during reconnect
cifs: smb2pdu: Fix potential NULL pointer dereference
This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes. The status handling code is
actually a running regression from the previous merge window which had
an incomplete fix (now reverted) and most of the remaining bug fixes
are for problems older than the current merge window.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWtMW7SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYdtAP97FhqR
x2lDO7J6QT8hMVqwPeQS0Xh5ZPbZLedPmfx9BAD+K1HauGv8J/eMggMDPGrWa/CP
tGrg2UorMrokLLdIbyA=
=fOJs
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
The status handling code is actually a running regression from the
previous merge window which had an incomplete fix (now reverted) and
most of the remaining bug fixes are for problems older than the
current merge window"
[ Side note: this merge also takes the base kernel git repository to 6+
million objects for the first time. Technically we hit it a couple of
merges ago already if you count all the tag objects, but now it
reaches 6M+ objects reachable from HEAD.
I was joking around that that's when I should switch to 5.0, because
3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
probably not, even if numerology is about as good a reason as any.
- Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
scsi: aacraid: Insure command thread is not recursively stopped
scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
scsi: qla2xxx: correctly shift host byte
scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
scsi: qla2xxx: Avoid double completion of abort command
scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
scsi: scsi_dh: Don't look for NULL devices handlers by name
scsi: core: remove redundant assignment to shost->use_blk_mq
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by
flex, bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by
flex, bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tD6R
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by flex,
bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by flex,
bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
* tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: extend output of 'listnewconfig'
kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg
Kbuild: fix # escaping in .cmd files for future Make
kbuild: deb-pkg: split generating packaging and build
kbuild: use -fmacro-prefix-map to make __FILE__ a relative path
kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers
kbuild: rename *-asn1.[ch] to *.asn1.[ch]
kbuild: clean up *-asn1.[ch] patterns from top-level Makefile
.gitignore: move *-asn1.[ch] patterns to the top-level .gitignore
kbuild: add %.dtb.S and %.dtb to 'targets' automatically
kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically
genksyms: generate lexer and parser during build instead of shipping
kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile
.gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore
kbuild: use HOSTLDFLAGS for single .c executables
Pull x86 fixes from Thomas Gleixner:
"A set of fixes and updates for x86:
- Address a swiotlb regression which was caused by the recent DMA
rework and made driver fail because dma_direct_supported() returned
false
- Fix a signedness bug in the APIC ID validation which caused invalid
APIC IDs to be detected as valid thereby bloating the CPU possible
space.
- Fix inconsisten config dependcy/select magic for the MFD_CS5535
driver.
- Fix a corruption of the physical address space bits when encryption
has reduced the address space and late cpuinfo updates overwrite
the reduced bit information with the original value.
- Dominiks syscall rework which consolidates the architecture
specific syscall functions so all syscalls can be wrapped with the
same macros. This allows to switch x86/64 to struct pt_regs based
syscalls. Extend the clearing of user space controlled registers in
the entry patch to the lower registers"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix signedness bug in APIC ID validity checks
x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption
x86/olpc: Fix inconsistent MFD_CS5535 configuration
swiotlb: Use dma_direct_supported() for swiotlb_ops
syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention
syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
syscalls/core, syscalls/x86: Clean up syscall stub naming convention
syscalls/x86: Extend register clearing on syscall entry to lower registers
syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64
syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls
syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls
syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
x86/syscalls: Don't pointlessly reload the system call number
x86/mm: Fix documentation of module mapping range with 4-level paging
x86/cpuid: Switch to 'static const' specifier
Pull x86 pti updates from Thomas Gleixner:
"Another series of PTI related changes:
- Remove the manual stack switch for user entries from the idtentry
code. This debloats entry by 5k+ bytes of text.
- Use the proper types for the asm/bootparam.h defines to prevent
user space compile errors.
- Use PAGE_GLOBAL for !PCID systems to gain back performance
- Prevent setting of huge PUD/PMD entries when the entries are not
leaf entries otherwise the entries to which the PUD/PMD points to
and are populated get lost"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pgtable: Don't set huge PUD/PMD on non-leaf entries
x86/pti: Leave kernel text global for !PCID
x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image
x86/pti: Enable global pages for shared areas
x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init
x86/mm: Comment _PAGE_GLOBAL mystery
x86/mm: Remove extra filtering in pageattr code
x86/mm: Do not auto-massage page protections
x86/espfix: Document use of _PAGE_GLOBAL
x86/mm: Introduce "default" kernel PTE mask
x86/mm: Undo double _PAGE_PSE clearing
x86/mm: Factor out pageattr _PAGE_GLOBAL setting
x86/entry/64: Drop idtentry's manual stack switch for user entries
x86/uapi: Fix asm/bootparam.h userspace compilation errors
Pull scheduler fixes from Thomas Gleixner:
"A few scheduler fixes:
- Prevent a bogus warning vs. runqueue clock update flags in
do_sched_rt_period_timer()
- Simplify the helper functions which handle requests for skipping
the runqueue clock updat.
- Do not unlock the tunables mutex in the error path of the cpu
frequency scheduler utils. Its not held.
- Enforce proper alignement for 'struct util_est' in sched_avg to
prevent a misalignment fault on IA64"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Force proper alignment of 'struct util_est'
sched/core: Simplify helpers for rq clock update skip requests
sched/rt: Fix rq->clock_update_flags < RQCF_ACT_SKIP warning
sched/cpufreq/schedutil: Fix error path mutex unlock
Pull more perf updates from Thomas Gleixner:
"A rather large set of perf updates:
Kernel:
- Fix various initialization issues
- Prevent creating [ku]probes for not CAP_SYS_ADMIN users
Tooling:
- Show only failing syscalls with 'perf trace --failure' (Arnaldo
Carvalho de Melo)
e.g: See what 'openat' syscalls are failing:
# perf trace --failure -e openat
762.323 ( 0.007 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video2) = -1 ENOENT No such file or directory
<SNIP N /dev/videoN open attempts... sigh, where is that improvised camera lid?!? >
790.228 ( 0.008 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video63) = -1 ENOENT No such file or directory
^C#
- Show information about the event (freq, nr_samples, total
period/nr_events) in the annotate --tui and --stdio2 'perf
annotate' output, similar to the first line in the 'perf report
--tui', but just for the samples for a the annotated symbol
(Arnaldo Carvalho de Melo)
- Introduce 'perf version --build-options' to show what features were
linked, aliased as well as a shorter 'perf -vv' (Jin Yao)
- Add a "dso_size" sort order (Kim Phillips)
- Remove redundant ')' in the tracepoint output in 'perf trace'
(Changbin Du)
- Synchronize x86's cpufeatures.h, no effect on toolss (Arnaldo
Carvalho de Melo)
- Show group details on the title line in the annotate browser and
'perf annotate --stdio2' output, so that the per-event columns can
have headers (Arnaldo Carvalho de Melo)
- Fixup vertical line separating metrics from instructions and
cleaning unused lines at the bottom, both in the annotate TUI
browser (Arnaldo Carvalho de Melo)
- Remove duplicated 'samples' in lost samples warning in
'perf report' (Arnaldo Carvalho de Melo)
- Synchronize i915_drm.h, silencing the perf build process,
automagically adding support for the new DRM_I915_QUERY ioctl
(Arnaldo Carvalho de Melo)
- Make auxtrace_queues__add_buffer() allocate struct buffer, from a
patchkit already applied (Adrian Hunter)
- Fix the --stdio2/TUI annotate output to include group details, be
it for a recorded '{a,b,f}' explicit event group or when forcing
group display using 'perf report --group' for a set of events not
recorded as a group (Arnaldo Carvalho de Melo)
- Fix display artifacts in the ui browser (base class for the
annotate and main report/top TUI browser) related to the extra
title lines work (Arnaldo Carvalho de Melo)
- perf auxtrace refactorings, leftovers from a previously partially
processed patchset (Adrian Hunter)
- Fix the builtin clang build (Sandipan Das, Arnaldo Carvalho de
Melo)
- Synchronize i915_drm.h, silencing a perf build warning and in the
process automagically adding support for a new ioctl command
(Arnaldo Carvalho de Melo)
- Fix a strncpy issue in uprobe tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open()
tracing/uprobe_event: Fix strncpy corner case
perf/core: Fix perf_uprobe_init()
perf/core: Fix perf_kprobe_init()
perf/core: Fix use-after-free in uprobe_perf_close()
perf tests clang: Fix function name for clang IR test
perf clang: Add support for recent clang versions
perf tools: Fix perf builds with clang support
perf tools: No need to include namespaces.h in util.h
perf hists browser: Remove leftover from row returned from refresh
perf hists browser: Show extra_title_lines in the 'D' debug hotkey
perf auxtrace: Make auxtrace_queues__add_buffer() do CPU filtering
tools headers uapi: Synchronize i915_drm.h
perf report: Remove duplicated 'samples' in lost samples warning
perf ui browser: Fixup cleaning unused lines at the bottom
perf annotate browser: Fixup vertical line separating metrics from instructions
perf annotate: Show group details on the title line
perf auxtrace: Make auxtrace_queues__add_buffer() allocate struct buffer
perf/x86/intel: Move regs->flags EXACT bit init
perf trace: Remove redundant ')'
...
Pull x86 EFI bootup fixlet from Thomas Gleixner:
"A single fix for an early boot warning caused by invoking
this_cpu_has() before SMP initialization"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix bogus warning during EFI bootup, use boot_cpu_has() instead of this_cpu_has() in build_cr3_noflush()
Pull irq affinity fixes from Thomas Gleixner:
- Fix error path handling in the affinity spreading code
- Make affinity spreading smarter to avoid issues on systems which
claim to have hotpluggable CPUs while in fact they can't hotplug
anything.
So instead of trying to spread the vectors (and thereby the
associated device queues) to all possibe CPUs, spread them on all
present CPUs first. If there are left over vectors after that first
step they are spread among the possible, but not present CPUs which
keeps the code backwards compatible for virtual decives and NVME
which allocate a queue per possible CPU, but makes the spreading
smarter for devices which have less queues than possible or present
CPUs.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/affinity: Spread irq vectors among present CPUs as far as possible
genirq/affinity: Allow irq spreading from a given starting point
genirq/affinity: Move actual irq vector spreading into a helper function
genirq/affinity: Rename *node_to_possible_cpumask as *node_to_cpumask
genirq/affinity: Don't return with empty affinity masks on error
Just one small thing here, it came in a while back but I didnt have
anything in my 4.16 queue, still its the only thing for 4.17 so sending
it alone.
Small cleanup:
- remove unused __ARCH_HAVE_MMU define
-----BEGIN PGP SIGNATURE-----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=edKX
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC fixlet from Stafford Horne:
"Just one small thing here, it came in a while back but I didnt have
anything in my 4.16 queue, still its the only thing for 4.17 so
sending it alone.
Small cleanup: remove unused __ARCH_HAVE_MMU define"
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: remove unused __ARCH_HAVE_MMU define
- Fix crashes when loading modules built with a different CONFIG_RELOCATABLE
value by adding CONFIG_RELOCATABLE to vermagic.
- Fix busy loops in the OPAL NVRAM driver if we get certain error conditions
from firmware.
- Remove tlbie trace points from KVM code that's called in real mode, because
it causes crashes.
- Fix checkstops caused by invalid tlbiel on Power9 Radix.
- Ensure the set of CPU features we "know" are always enabled is actually the
minimal set when we build with support for firmware supplied CPU features.
Thanks to:
Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----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=0e7c
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes when loading modules built with a different
CONFIG_RELOCATABLE value by adding CONFIG_RELOCATABLE to vermagic.
- Fix busy loops in the OPAL NVRAM driver if we get certain error
conditions from firmware.
- Remove tlbie trace points from KVM code that's called in real mode,
because it causes crashes.
- Fix checkstops caused by invalid tlbiel on Power9 Radix.
- Ensure the set of CPU features we "know" are always enabled is
actually the minimal set when we build with support for firmware
supplied CPU features.
Thanks to: Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.
* tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix CPU_FTRS_ALWAYS vs DT CPU features
powerpc/mm/radix: Fix checkstops caused by invalid tlbiel
KVM: PPC: Book3S HV: trace_tlbie must not be called in realmode
powerpc/8xx: Fix build with hugetlbfs enabled
powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops
powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops
powerpc/fscr: Enable interrupts earlier before calling get_user()
powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()
powerpc/modules: Fix crashes by adding CONFIG_RELOCATABLE to vermagic
Merge yet more updates from Andrew Morton:
- various hotfixes
- kexec_file updates and feature work
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
kernel/kexec_file.c: move purgatories sha256 to common code
kernel/kexec_file.c: allow archs to set purgatory load address
kernel/kexec_file.c: remove mis-use of sh_offset field during purgatory load
kernel/kexec_file.c: remove unneeded variables in kexec_purgatory_setup_sechdrs
kernel/kexec_file.c: remove unneeded for-loop in kexec_purgatory_setup_sechdrs
kernel/kexec_file.c: split up __kexec_load_puragory
kernel/kexec_file.c: use read-only sections in arch_kexec_apply_relocations*
kernel/kexec_file.c: search symbols in read-only kexec_purgatory
kernel/kexec_file.c: make purgatory_info->ehdr const
kernel/kexec_file.c: remove checks in kexec_purgatory_load
include/linux/kexec.h: silence compile warnings
kexec_file, x86: move re-factored code to generic side
x86: kexec_file: clean up prepare_elf64_headers()
x86: kexec_file: lift CRASH_MAX_RANGES limit on crash_mem buffer
x86: kexec_file: remove X86_64 dependency from prepare_elf64_headers()
x86: kexec_file: purge system-ram walking from prepare_elf64_headers()
kexec_file,x86,powerpc: factor out kexec_file_ops functions
kexec_file: make use of purgatory optional
proc: revalidate misc dentries
mm, slab: reschedule cache_reap() on the same CPU
...
The code to verify the new kernels sha digest is applicable for all
architectures. Move it to common code.
One problem is the string.c implementation on x86. Currently sha256
includes x86/boot/string.h which defines memcpy and memset to be gcc
builtins. By moving the sha256 implementation to common code and
changing the include to linux/string.h both functions are no longer
defined. Thus definitions have to be provided in x86/purgatory/string.c
Link: http://lkml.kernel.org/r/20180321112751.22196-12-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For s390 new kernels are loaded to fixed addresses in memory before they
are booted. With the current code this is a problem as it assumes the
kernel will be loaded to an 'arbitrary' address. In particular,
kexec_locate_mem_hole searches for a large enough memory region and sets
the load address (kexec_bufer->mem) to it.
Luckily there is a simple workaround for this problem. By returning 1
in arch_kexec_walk_mem, kexec_locate_mem_hole is turned off. This
allows the architecture to set kbuf->mem by hand. While the trick works
fine for the kernel it does not for the purgatory as here the
architectures don't have access to its kexec_buffer.
Give architectures access to the purgatories kexec_buffer by changing
kexec_load_purgatory to take a pointer to it. With this change
architectures have access to the buffer and can edit it as they need.
A nice side effect of this change is that we can get rid of the
purgatory_info->purgatory_load_address field. As now the information
stored there can directly be accessed from kbuf->mem.
Link: http://lkml.kernel.org/r/20180321112751.22196-11-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code uses the sh_offset field in purgatory_info->sechdrs to
store a pointer to the current load address of the section. Depending
whether the section will be loaded or not this is either a pointer into
purgatory_info->purgatory_buf or kexec_purgatory. This is not only a
violation of the ELF standard but also makes the code very hard to
understand as you cannot tell if the memory you are using is read-only
or not.
Remove this misuse and store the offset of the section in
pugaroty_info->purgatory_buf in sh_offset.
Link: http://lkml.kernel.org/r/20180321112751.22196-10-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main loop currently uses quite a lot of variables to update the
section headers. Some of them are unnecessary. So clean them up a
little.
Link: http://lkml.kernel.org/r/20180321112751.22196-9-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To update the entry point there is an extra loop over all section
headers although this can be done in the main loop. So move it there
and eliminate the extra loop and variable to store the 'entry section
index'.
Also, in the main loop, move the usual case, i.e. non-bss section, out
of the extra if-block.
Link: http://lkml.kernel.org/r/20180321112751.22196-8-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When inspecting __kexec_load_purgatory you find that it has two tasks
1) setting up the kexec_buffer for the new kernel and,
2) setting up pi->sechdrs for the final load address.
The two tasks are independent of each other. To improve readability
split up __kexec_load_purgatory into two functions, one for each task,
and call them directly from kexec_load_purgatory.
Link: http://lkml.kernel.org/r/20180321112751.22196-7-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the relocations are applied to the purgatory only the section the
relocations are applied to is writable. The other sections, i.e. the
symtab and .rel/.rela, are in read-only kexec_purgatory. Highlight this
by marking the corresponding variables as 'const'.
While at it also change the signatures of arch_kexec_apply_relocations* to
take section pointers instead of just the index of the relocation section.
This removes the second lookup and sanity check of the sections in arch
code.
Link: http://lkml.kernel.org/r/20180321112751.22196-6-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The stripped purgatory does not contain a symtab. So when looking for
symbols this is done in read-only kexec_purgatory. Highlight this by
marking the corresponding variables as 'const'.
Link: http://lkml.kernel.org/r/20180321112751.22196-5-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kexec_purgatory buffer is read-only. Thus all pointers into
kexec_purgatory are read-only, too. Point this out by explicitly
marking purgatory_info->ehdr as 'const' and update the comments in
purgatory_info.
Link: http://lkml.kernel.org/r/20180321112751.22196-4-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before the purgatory is loaded several checks are done whether the ELF
file in kexec_purgatory is valid or not. These checks are incomplete.
For example they don't check for the total size of the sections defined
in the section header table or if the entry point actually points into
the purgatory.
On the other hand the purgatory, although an ELF file on its own, is
part of the kernel. Thus not trusting the purgatory means not trusting
the kernel build itself.
So remove all validity checks on the purgatory and just trust the kernel
build.
Link: http://lkml.kernel.org/r/20180321112751.22196-3-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "kexec_file: Clean up purgatory load", v2.
Following the discussion with Dave and AKASHI, here are the common code
patches extracted from my recent patch set (Add kexec_file_load support
to s390) [1]. The patches were extracted to allow upstream integration
together with AKASHI's common code patches before the arch code gets
adjusted to the new base.
The reason for this series is to prepare common code for adding
kexec_file_load to s390 as well as cleaning up the mis-use of the
sh_offset field during purgatory load. In detail this series contains:
Patch #1&2: Minor cleanups/fixes.
Patch #3-9: Clean up the purgatory load/relocation code. Especially
remove the mis-use of the purgatory_info->sechdrs->sh_offset field,
currently holding a pointer into either kexec_purgatory (ro) or
purgatory_buf (rw) depending on the section. With these patches the
section address will be calculated verbosely and sh_offset will contain
the offset of the section in the stripped purgatory binary
(purgatory_buf).
Patch #10: Allows architectures to set the purgatory load address. This
patch is important for s390 as the kernel and purgatory have to be
loaded to fixed addresses. In current code this is impossible as the
purgatory load is opaque to the architecture.
Patch #11: Moves x86 purgatories sha implementation to common lib/
directory to allow reuse in other architectures.
This patch (of 11)
When building the kernel with CONFIG_KEXEC_FILE enabled gcc prints a
compile warning multiple times.
In file included from <path>/linux/init/initramfs.c:526:0:
<path>/include/linux/kexec.h:120:9: warning: `struct kimage' declared inside parameter list [enabled by default]
unsigned long cmdline_len);
^
This is because the typedefs for kexec_file_load uses struct kimage
before it is declared. Fix this by simply forward declaring struct
kimage.
Link: http://lkml.kernel.org/r/20180321112751.22196-2-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the previous patches, commonly-used routines, exclude_mem_range() and
prepare_elf64_headers(), were carved out. Now place them in kexec
common code. A prefix "crash_" is given to each of their names to avoid
possible name collisions.
Link: http://lkml.kernel.org/r/20180306102303.9063-8-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removing bufp variable in prepare_elf64_headers() makes the code simpler
and more understandable.
Link: http://lkml.kernel.org/r/20180306102303.9063-7-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While CRASH_MAX_RANGES (== 16) seems to be good enough, fixed-number
array is not a good idea in general.
In this patch, size of crash_mem buffer is calculated as before and the
buffer is now dynamically allocated. This change also allows removing
crash_elf_data structure.
Link: http://lkml.kernel.org/r/20180306102303.9063-6-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code guarded by CONFIG_X86_64 is necessary on some architectures
which have a dedicated kernel mapping outside of linear memory mapping.
(arm64 is among those.)
In this patch, an additional argument, kernel_map, is added to enable/
disable the code removing #ifdef.
Link: http://lkml.kernel.org/r/20180306102303.9063-5-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While prepare_elf64_headers() in x86 looks pretty generic for other
architectures' use, it contains some code which tries to list crash
memory regions by walking through system resources, which is not always
architecture agnostic. To make this function more generic, the related
code should be purged.
In this patch, prepare_elf64_headers() simply scans crash_mem buffer
passed and add all the listed regions to elf header as a PT_LOAD
segment. So walk_system_ram_res(prepare_elf64_headers_callback) have
been moved forward before prepare_elf64_headers() where the callback,
prepare_elf64_headers_callback(), is now responsible for filling up
crash_mem buffer.
Meanwhile exclude_elf_header_ranges() used to be called every time in
this callback it is rather redundant and now called only once in
prepare_elf_headers() as well.
Link: http://lkml.kernel.org/r/20180306102303.9063-4-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As arch_kexec_kernel_image_{probe,load}(),
arch_kimage_file_post_load_cleanup() and arch_kexec_kernel_verify_sig()
are almost duplicated among architectures, they can be commonalized with
an architecture-defined kexec_file_ops array. So let's factor them out.
Link: http://lkml.kernel.org/r/20180306102303.9063-3-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "kexec_file, x86, powerpc: refactoring for other
architecutres", v2.
This is a preparatory patchset for adding kexec_file support on arm64.
It was originally included in a arm64 patch set[1], but Philipp is also
working on their kexec_file support on s390[2] and some changes are now
conflicting.
So these common parts were extracted and put into a separate patch set
for better integration. What's more, my original patch#4 was split into
a few small chunks for easier review after Dave's comment.
As such, the resulting code is basically identical with my original, and
the only *visible* differences are:
- renaming of _kexec_kernel_image_probe() and _kimage_file_post_load_cleanup()
- change one of types of arguments at prepare_elf64_headers()
Those, unfortunately, require a couple of trivial changes on the rest
(#1, #6 to #13) of my arm64 kexec_file patch set[1].
Patch #1 allows making a use of purgatory optional, particularly useful
for arm64.
Patch #2 commonalizes arch_kexec_kernel_{image_probe, image_load,
verify_sig}() and arch_kimage_file_post_load_cleanup() across
architectures.
Patches #3-#7 are also intended to generalize parse_elf64_headers(),
along with exclude_mem_range(), to be made best re-use of.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-February/561182.html
[2] http://lkml.iu.edu//hypermail/linux/kernel/1802.1/02596.html
This patch (of 7):
On arm64, crash dump kernel's usable memory is protected by *unmapping*
it from kernel virtual space unlike other architectures where the region
is just made read-only. It is highly unlikely that the region is
accidentally corrupted and this observation rationalizes that digest
check code can also be dropped from purgatory. The resulting code is so
simple as it doesn't require a bit ugly re-linking/relocation stuff,
i.e. arch_kexec_apply_relocations_add().
Please see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2017-December/545428.html
All that the purgatory does is to shuffle arguments and jump into a new
kernel, while we still need to have some space for a hash value
(purgatory_sha256_digest) which is never checked against.
As such, it doesn't make sense to have trampline code between old kernel
and new kernel on arm64.
This patch introduces a new configuration, ARCH_HAS_KEXEC_PURGATORY, and
allows related code to be compiled in only if necessary.
[takahiro.akashi@linaro.org: fix trivial screwup]
Link: http://lkml.kernel.org/r/20180309093346.GF25863@linaro.org
Link: http://lkml.kernel.org/r/20180306102303.9063-2-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If module removes proc directory while another process pins it by
chdir'ing to it, then subsequent recreation of proc entry and all
entries down the tree will not be visible to any process until pinning
process unchdir from directory and unpins everything.
Steps to reproduce:
proc_mkdir("aaa", NULL);
proc_create("aaa/bbb", ...);
chdir("/proc/aaa");
remove_proc_entry("aaa/bbb", NULL);
remove_proc_entry("aaa", NULL);
proc_mkdir("aaa", NULL);
# inaccessible because "aaa" dentry still points
# to the original "aaa".
proc_create("aaa/bbb", ...);
Fix is to implement ->d_revalidate and ->d_delete.
Link: http://lkml.kernel.org/r/20180312201938.GA4871@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cache_reap() is initially scheduled in start_cpu_timer() via
schedule_delayed_work_on(). But then the next iterations are scheduled
via schedule_delayed_work(), i.e. using WORK_CPU_UNBOUND.
Thus since commit ef55718044 ("workqueue: schedule WORK_CPU_UNBOUND
work on wq_unbound_cpumask CPUs") there is no guarantee the future
iterations will run on the originally intended cpu, although it's still
preferred. I was able to demonstrate this with
/sys/module/workqueue/parameters/debug_force_rr_cpu. IIUC, it may also
happen due to migrating timers in nohz context. As a result, some cpu's
would be calling cache_reap() more frequently and others never.
This patch uses schedule_delayed_work_on() with the current cpu when
scheduling the next iteration.
Link: http://lkml.kernel.org/r/20180411070007.32225-1-vbabka@suse.cz
Fixes: ef55718044 ("workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 6326fec112 ("mm: Use owner_priv bit for PageSwapCache,
valid when PageSwapBacked"), PG_swapcache is an alias for
PG_owner_priv_1, which may be also used for other purposes.
To know whether the bit indeed has the PG_swapcache meaning, it is
necessary to check PG_swapbacked, hence this bit must be exported.
Link: http://lkml.kernel.org/r/20180410161345.142e142d@ezekiel.suse.cz
Signed-off-by: Petr Tesarik <ptesarik@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: "Marc-Andr Lureau" <marcandre.lureau@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
syzbot reported a use-after-free of shm_file_data(file)->file->f_op in
shm_get_unmapped_area(), called via sys_remap_file_pages().
Unfortunately it couldn't generate a reproducer, but I found a bug which
I think caused it. When remap_file_pages() is passed a full System V
shared memory segment, the memory is first unmapped, then a new map is
created using the ->vm_file. Between these steps, the shm ID can be
removed and reused for a new shm segment. But, shm_mmap() only checks
whether the ID is currently valid before calling the underlying file's
->mmap(); it doesn't check whether it was reused. Thus it can use the
wrong underlying file, one that was already freed.
Fix this by making the "outer" shm file (the one that gets put in
->vm_file) hold a reference to the real shm file, and by making
__shm_open() require that the file associated with the shm ID matches
the one associated with the "outer" file.
Taking the reference to the real shm file is needed to fully solve the
problem, since otherwise sfd->file could point to a freed file, which
then could be reallocated for the reused shm ID, causing the wrong shm
segment to be mapped (and without the required permission checks).
Commit 1ac0b6dec6 ("ipc/shm: handle removed segments gracefully in
shm_mmap()") almost fixed this bug, but it didn't go far enough because
it didn't consider the case where the shm ID is reused.
The following program usually reproduces this bug:
#include <stdlib.h>
#include <sys/shm.h>
#include <sys/syscall.h>
#include <unistd.h>
int main()
{
int is_parent = (fork() != 0);
srand(getpid());
for (;;) {
int id = shmget(0xF00F, 4096, IPC_CREAT|0700);
if (is_parent) {
void *addr = shmat(id, NULL, 0);
usleep(rand() % 50);
while (!syscall(__NR_remap_file_pages, addr, 4096, 0, 0, 0));
} else {
usleep(rand() % 50);
shmctl(id, IPC_RMID, NULL);
}
}
}
It causes the following NULL pointer dereference due to a 'struct file'
being used while it's being freed. (I couldn't actually get a KASAN
use-after-free splat like in the syzbot report. But I think it's
possible with this bug; it would just take a more extraordinary race...)
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 9 PID: 258 Comm: syz_ipc Not tainted 4.16.0-05140-gf8cf2f16a7c95 #189
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
RIP: 0010:d_inode include/linux/dcache.h:519 [inline]
RIP: 0010:touch_atime+0x25/0xd0 fs/inode.c:1724
[...]
Call Trace:
file_accessed include/linux/fs.h:2063 [inline]
shmem_mmap+0x25/0x40 mm/shmem.c:2149
call_mmap include/linux/fs.h:1789 [inline]
shm_mmap+0x34/0x80 ipc/shm.c:465
call_mmap include/linux/fs.h:1789 [inline]
mmap_region+0x309/0x5b0 mm/mmap.c:1712
do_mmap+0x294/0x4a0 mm/mmap.c:1483
do_mmap_pgoff include/linux/mm.h:2235 [inline]
SYSC_remap_file_pages mm/mmap.c:2853 [inline]
SyS_remap_file_pages+0x232/0x310 mm/mmap.c:2769
do_syscall_64+0x64/0x1a0 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ebiggers@google.com: add comment]
Link: http://lkml.kernel.org/r/20180410192850.235835-1-ebiggers3@gmail.com
Link: http://lkml.kernel.org/r/20180409043039.28915-1-ebiggers3@gmail.com
Reported-by: syzbot+d11f321e7f1923157eac80aa990b446596f46439@syzkaller.appspotmail.com
Fixes: c8d78c1823 ("mm: replace remap_file_pages() syscall with emulation")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building orangefs on MMU-less machines now results in a link error
because of the newly introduced use of the filemap_page_mkwrite()
function:
ERROR: "filemap_page_mkwrite" [fs/orangefs/orangefs.ko] undefined!
This adds a dummy version for it, similar to the existing
generic_file_mmap and generic_file_readonly_mmap stubs in the same file,
to avoid the link error without adding #ifdefs in each file system that
uses these.
Link: http://lkml.kernel.org/r/20180409105555.2439976-1-arnd@arndb.de
Fixes: a5135eeab2 ("orangefs: implement vm_ops->fault")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Brandenburg <martin@omnibond.com>
Cc: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__get_user_pages_fast handles errors differently from
get_user_pages_fast: the former always returns the number of pages
pinned, the later might return a negative error code.
Link: http://lkml.kernel.org/r/1522962072-182137-6-git-send-email-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_user_pages_fast is supposed to be a faster drop-in equivalent of
get_user_pages. As such, callers expect it to return a negative return
code when passed an invalid address, and never expect it to return 0
when passed a positive number of pages, since its documentation says:
* Returns number of pages pinned. This may be fewer than the number
* requested. If nr_pages is 0 or negative, returns 0. If no pages
* were pinned, returns -errno.
When get_user_pages_fast fall back on get_user_pages this is exactly
what happens. Unfortunately the implementation is inconsistent: it
returns 0 if passed a kernel address, confusing callers: for example,
the following is pretty common but does not appear to do the right thing
with a kernel address:
ret = get_user_pages_fast(addr, 1, writeable, &page);
if (ret < 0)
return ret;
Change get_user_pages_fast to return -EFAULT when supplied a kernel
address to make it match expectations.
All callers have been audited for consistency with the documented
semantics.
Link: http://lkml.kernel.org/r/1522962072-182137-4-git-send-email-mst@redhat.com
Fixes: 5b65c4677a ("mm, x86/mm: Fix performance regression in get_user_pages_fast()")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm/get_user_pages_fast fixes, cleanups", v2.
Turns out get_user_pages_fast and __get_user_pages_fast return different
values on error when given a single page: __get_user_pages_fast returns
0. get_user_pages_fast returns either 0 or an error.
Callers of get_user_pages_fast expect an error so fix it up to return an
error consistently.
Stress the difference between get_user_pages_fast and
__get_user_pages_fast to make sure callers aren't confused.
This patch (of 3):
__gup_benchmark_ioctl does not handle the case where get_user_pages_fast
fails:
- a negative return code will cause a buffer overrun
- returning with partial success will cause use of uninitialized
memory.
[akpm@linux-foundation.org: simplification]
Link: http://lkml.kernel.org/r/1522962072-182137-3-git-send-email-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've got a bug report indicating a kernel panic at booting on an x86-32
system, and it turned out to be the invalid PCI resource assigned after
reallocation. __find_resource() first aligns the resource start address
and resets the end address with start+size-1 accordingly, then checks
whether it's contained. Here the end address may overflow the integer,
although resource_contains() still returns true because the function
validates only start and end address. So this ends up with returning an
invalid resource (start > end).
There was already an attempt to cover such a problem in the commit
47ea91b405 ("Resource: fix wrong resource window calculation"), but
this case is an overseen one.
This patch adds the validity check of the newly calculated resource for
avoiding the integer overflow problem.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1086739
Link: http://lkml.kernel.org/r/s5hpo37d5l8.wl-tiwai@suse.de
Fixes: 23c570a674 ("resource: ability to resize an allocated resource")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Michael Henders <hendersm@shaw.ca>
Tested-by: Michael Henders <hendersm@shaw.ca>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull overlayfs updates from Miklos Szeredi:
"In addition to bug fixes and cleanups there are two new features from
Amir:
- Consistent inode number support for the case when layers are not
all on the same filesystem (feature is dubbed "xino").
- Optimize overlayfs file handle decoding. This one touches the
exportfs interface to allow detecting the disconnected directory
case"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: update documentation w.r.t "xino" feature
ovl: add support for "xino" mount and config options
ovl: consistent d_ino for non-samefs with xino
ovl: consistent i_ino for non-samefs with xino
ovl: constant st_ino for non-samefs with xino
ovl: allocate anon bdev per unique lower fs
ovl: factor out ovl_map_dev_ino() helper
ovl: cleanup ovl_update_time()
ovl: add WARN_ON() for non-dir redirect cases
ovl: cleanup setting OVL_INDEX
ovl: set d->is_dir and d->opaque for last path element
ovl: Do not check for redirect if this is last layer
ovl: lookup in inode cache first when decoding lower file handle
ovl: do not try to reconnect a disconnected origin dentry
ovl: disambiguate ovl_encode_fh()
ovl: set lower layer st_dev only if setting lower st_ino
ovl: fix lookup with middle layer opaque dir and absolute path redirects
ovl: Set d->last properly during lookup
ovl: set i_ino to the value of st_ino for NFS export
