cls_bpf used to take care of tracking what offload state a filter
is in, i.e. it would track if offload request succeeded or not.
This information would then be used to issue correct requests to
the driver, e.g. requests for statistics only on offloaded filters,
removing only filters which were offloaded, using add instead of
replace if previous filter was not added etc.
This tracking of offload state no longer functions with the new
callback infrastructure. There could be multiple entities trying
to offload the same filter.
Throw out all the tracking and corresponding commands and simply
pass to the drivers both old and new bpf program. Drivers will
have to deal with offload state tracking by themselves.
Fixes: 3f7889c4c7 ("net: sched: cls_bpf: call block callbacks for offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(I can trivially verify that that idr_remove in cleanup_net happens
after the network namespace count has dropped to zero --EWB)
Function get_net_ns_by_id() does not check for net::count
after it has found a peer in netns_ids idr.
It may dereference a peer, after its count has already been
finaly decremented. This leads to double free and memory
corruption:
put_net(peer) rtnl_lock()
atomic_dec_and_test(&peer->count) [count=0] ...
__put_net(peer) get_net_ns_by_id(net, id)
spin_lock(&cleanup_list_lock)
list_add(&net->cleanup_list, &cleanup_list)
spin_unlock(&cleanup_list_lock)
queue_work() peer = idr_find(&net->netns_ids, id)
| get_net(peer) [count=1]
| ...
| (use after final put)
v ...
cleanup_net() ...
spin_lock(&cleanup_list_lock) ...
list_replace_init(&cleanup_list, ..) ...
spin_unlock(&cleanup_list_lock) ...
... ...
... put_net(peer)
... atomic_dec_and_test(&peer->count) [count=0]
... spin_lock(&cleanup_list_lock)
... list_add(&net->cleanup_list, &cleanup_list)
... spin_unlock(&cleanup_list_lock)
... queue_work()
... rtnl_unlock()
rtnl_lock() ...
for_each_net(tmp) { ...
id = __peernet2id(tmp, peer) ...
spin_lock_irq(&tmp->nsid_lock) ...
idr_remove(&tmp->netns_ids, id) ...
... ...
net_drop_ns() ...
net_free(peer) ...
} ...
|
v
cleanup_net()
...
(Second free of peer)
Also, put_net() on the right cpu may reorder with left's cpu
list_replace_init(&cleanup_list, ..), and then cleanup_list
will be corrupted.
Since cleanup_net() is executed in worker thread, while
put_net(peer) can happen everywhere, there should be
enough time for concurrent get_net_ns_by_id() to pick
the peer up, and the race does not seem to be unlikely.
The patch fixes the problem in standard way.
(Also, there is possible problem in peernet2id_alloc(), which requires
check for net::count under nsid_lock and maybe_get_net(peer), but
in current stable kernel it's used under rtnl_lock() and it has to be
safe. Openswitch begun to use peernet2id_alloc(), and possibly it should
be fixed too. While this is not in stable kernel yet, so I'll send
a separate message to netdev@ later).
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Fixes: 0c7aecd4bd "netns: add rtnl cmd to add and get peer netns ids"
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT says:
====================
Few mvneta fixes
here it is a small series of fixes found on the mvneta driver. They
had been already used in the vendor kernel and are now ported to
mainline.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few reasons in mvneta_rx_swbm() function when received packet
is dropped. mvneta_rx_error() should be called only if error bit [16]
is set in rx descriptor.
[gregory.clement@free-electrons.com: add fixes tag]
Cc: stable@vger.kernel.org
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the RX queue association with each CPU, a typo was made in
the mvneta_cleanup_rxqs() function. This patch fixes it.
[gregory.clement@free-electrons.com: add commit log and fixes tag]
Cc: stable@vger.kernel.org
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port connect to PHY in polling mode (with poll interval 1 sec),
port and phy link status must be synchronize in order don't loss link
change event.
[gregory.clement@free-electrons.com: add fixes tag]
Cc: <stable@vger.kernel.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recently added fib_metrics_match() causes a regression for routes
with both RTAX_FEATURES and RTAX_CC_ALGO if the latter has
TCP_CONG_NEEDS_ECN flag set:
| # ip link add d0 type dummy
| # ip link set d0 up
| # ip route add 172.29.29.0/24 dev d0 features ecn congctl dctcp
| # ip route del 172.29.29.0/24 dev d0 features ecn congctl dctcp
| RTNETLINK answers: No such process
During route insertion, fib_convert_metrics() detects that the given CC
algo requires ECN and hence sets DST_FEATURE_ECN_CA bit in
RTAX_FEATURES.
During route deletion though, fib_metrics_match() compares stored
RTAX_FEATURES value with that from userspace (which obviously has no
knowledge about DST_FEATURE_ECN_CA) and fails.
Fixes: 5f9ae3d9e7 ("ipv4: do metrics match when looking up and deleting a route")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in dwmac4_wrback_get_rx_timestamp_status the timestamp is found
in the context descriptor following the current descriptor. However the
current code looks for the context descriptor in the current
descriptor, which will always fail.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GMAC4 the value written in PTP_SSIR should be shifted however
the shifted value is also used in subsequent calculations which results
in a bad timestamp value.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When, during a join operation, or during message transmission, a group
member needs to be added to the group's 'congested' list, we sort it
into the list in ascending order, according to its current advertised
window size. However, we miss the case when the member is already on
that list. This will have the result that the member, after the window
size has been decremented, might be at the wrong position in that list.
This again may have the effect that we during broadcast and multicast
transmissions miss the fact that a destination is not yet ready for
reception, and we end up sending anyway. From this point on, the
behavior during the remaining session is unpredictable, e.g., with
underflowing window sizes.
We now correct this bug by unconditionally removing the member from
the list before (re-)sorting it in.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
(client) gre6 <---> eth1 (route) eth2 <---> gre6 (server)
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix as the patch "ip_gre: remove the incorrect mtu limit for
ipgre tap" is also needed for ip6_gre.
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipgre tap driver calls ether_setup(), after commit 61e84623ac
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the ipgre tap device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Besides, it's .change_mtu already does the right check. So this
patch is just to set max_mtu as 0, and leave the check to it's
.change_mtu.
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ip tunnels, now vxlan doesn't do any pmtu update for
upper dst pmtu, even if it doesn't match the lower dst pmtu
any more.
The problem can be reproduced when reducing the vxlan lower
dev's pmtu when running netperf. In jianlin's testing, the
performance went to 1/7 of the previous.
This patch is to update the upper dst pmtu to match the lower
dst pmtu on tx path so that packets can be sent out even when
lower dev's pmtu has been changed.
It also works for metadata dst.
Note that this patch doesn't process any pmtu icmp packet.
But even in the future, the support for pmtu icmp packets
process of udp tunnels will also needs this.
The same thing will be done for geneve in another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions EMAC stop reception of incoming packets and
continuously increment R_MISS register instead of saving data into
provided buffer. The commit implement workaround for such situation.
Then the stall detected EMAC will be restarted.
On device the stall looks like the device lost it's dynamic IP address.
ifconfig shows that interface error counter rapidly increments.
At the same time on the DHCP server we can see continues DHCP-requests
from device.
In real network stalls happen really rarely. To make them frequent the
broadcast storm[1] should be simulated. For simulation it is necessary
to make following connections:
1. connect radxarock to 1st port of switch
2. connect some PC to 2nd port of switch
3. connect two other free ports together using standard ethernet cable,
in order to make a switching loop.
After that, is necessary to make a broadcast storm. For example, running on
PC 'ping' to some IP address triggers ARP-request storm. After some
time (~10sec), EMAC on rk3188 will stall.
Observed and tested on rk3188 radxarock.
[1] https://en.wikipedia.org/wiki/Broadcast_radiation
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 63dd00fa3e.
RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Fixes: 63dd00fa3e ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a hang issue seen when changing the MTU size from 1500 MTU
to 9000 MTU on both 5717 and 5719 chips. In discussion with Broadcom,
they've indicated that these chipsets have the same phy as the 57766
chipset, so the same workarounds apply. This has been tested by IBM
on both Power 8 and Power 9 systems as well as by Broadcom on x86
hardware and has been confirmed to resolve the hang issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* hwsim:
- set To-DS bit in some frames missing it
- fix sleeping in atomic
* nl80211:
- doc cleanup
- fix locking in an error path
* build:
- don't append to created certs C files
- ship certificate pre-hexdumped
-----BEGIN PGP SIGNATURE-----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=OWs9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more fixes:
* hwsim:
- set To-DS bit in some frames missing it
- fix sleeping in atomic
* nl80211:
- doc cleanup
- fix locking in an error path
* build:
- don't append to created certs C files
- ship certificate pre-hexdumped
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only does this remove the need for the hexdump code in most
normal kernel builds (still there for the extra directory), but
it also removes the need to ship binary files, which apparently
is somewhat problematic, as Randy reported.
While at it, also add the generated files to clean-files.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ca986ad9bc (nl80211: allow multiple active scheduled scan
requests) removed WIPHY_FLAG_SUPPORTS_SCHED_SCAN but left the kerneldoc
description in place, leading to this docs-build warning:
./include/net/cfg80211.h:3278: warning: Excess enum value
'WIPHY_FLAG_SUPPORTS_SCHED_SCAN' description in 'wiphy_flags'
Remove the line and gain a bit of peace.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver may sleep under a spinlock.
The function call path is:
hwsim_get_radio_nl (acquire the spinlock)
nlmsg_new(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the certs C code generation appends to the generated files,
which is most likely a leftover from commit 715a123347 ("wireless:
don't write C files on failures"). This causes duplicate code in the
generated files if the certificates have their timestamps modified
between builds and thereby trigger the generation rules.
Fixes: 715a123347 ("wireless: don't write C files on failures")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Same as in ieee80211_nullfunc_get, enable the TODS bit, otherwise the
nullfunc packet will not be handled in ap rx path.
(will be dropped in ieee80211_accept_frame()).
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are several error paths in xgene_mdio_probe(),
where clk is left undisabled. The patch fixes them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Observed on the 88e1512 in SGMII-to-Copper mode, negotiating pause
is unreliable. While the pause bits can be set in the advertisment
register, they clear shortly after negotiation with a link partner
commences irrespective of the cause of the negotiation.
While these bits may be correctly conveyed to the link partner on the
first negotiation, a subsequent negotiation (eg, due to negotiation
restart by the link partner, or reconnection of the cable) will result
in the link partner seeing these bits as zero, while the kernel
believes that it has advertised pause modes.
This leads to the local kernel evaluating (eg) symmetric pause mode,
while the remote end evaluates that we have no pause mode capability.
Since we can't guarantee the advertisment, disable pause mode support
with this PHY when used in SGMII-to-Copper mode.
The 88e1510 in RGMII-to-Copper mode appears to behave correctly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The early call to br_stp_change_bridge_id in bridge's newlink can cause
a memory leak if an error occurs during the newlink because the fdb
entries are not cleaned up if a different lladdr was specified, also
another minor issue is that it generates fdb notifications with
ifindex = 0. Another unrelated memory leak is the bridge sysfs entries
which get added on NETDEV_REGISTER event, but are not cleaned up in the
newlink error path. To remove this special case the call to
br_stp_change_bridge_id is done after netdev register and we cleanup the
bridge on changelink error via br_dev_delete to plug all leaks.
This patch makes netlink bridge destruction on newlink error the same as
dellink and ioctl del which is necessary since at that point we have a
fully initialized bridge device.
To reproduce the issue:
$ ip l add br0 address 00:11:22:33:44:55 type bridge group_fwd_mask 1
RTNETLINK answers: Invalid argument
$ rmmod bridge
[ 1822.142525] =============================================================================
[ 1822.143640] BUG bridge_fdb_cache (Tainted: G O ): Objects remaining in bridge_fdb_cache on __kmem_cache_shutdown()
[ 1822.144821] -----------------------------------------------------------------------------
[ 1822.145990] Disabling lock debugging due to kernel taint
[ 1822.146732] INFO: Slab 0x0000000092a844b2 objects=32 used=2 fp=0x00000000fef011b0 flags=0x1ffff8000000100
[ 1822.147700] CPU: 2 PID: 13584 Comm: rmmod Tainted: G B O 4.15.0-rc2+ #87
[ 1822.148578] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 1822.150008] Call Trace:
[ 1822.150510] dump_stack+0x78/0xa9
[ 1822.151156] slab_err+0xb1/0xd3
[ 1822.151834] ? __kmalloc+0x1bb/0x1ce
[ 1822.152546] __kmem_cache_shutdown+0x151/0x28b
[ 1822.153395] shutdown_cache+0x13/0x144
[ 1822.154126] kmem_cache_destroy+0x1c0/0x1fb
[ 1822.154669] SyS_delete_module+0x194/0x244
[ 1822.155199] ? trace_hardirqs_on_thunk+0x1a/0x1c
[ 1822.155773] entry_SYSCALL_64_fastpath+0x23/0x9a
[ 1822.156343] RIP: 0033:0x7f929bd38b17
[ 1822.156859] RSP: 002b:00007ffd160e9a98 EFLAGS: 00000202 ORIG_RAX: 00000000000000b0
[ 1822.157728] RAX: ffffffffffffffda RBX: 00005578316ba090 RCX: 00007f929bd38b17
[ 1822.158422] RDX: 00007f929bd9ec60 RSI: 0000000000000800 RDI: 00005578316ba0f0
[ 1822.159114] RBP: 0000000000000003 R08: 00007f929bff5f20 R09: 00007ffd160e8a11
[ 1822.159808] R10: 00007ffd160e9860 R11: 0000000000000202 R12: 00007ffd160e8a80
[ 1822.160513] R13: 0000000000000000 R14: 0000000000000000 R15: 00005578316ba090
[ 1822.161278] INFO: Object 0x000000007645de29 @offset=0
[ 1822.161666] INFO: Object 0x00000000d5df2ab5 @offset=128
Fixes: 30313a3d57 ("bridge: Handle IFLA_ADDRESS correctly when creating bridge device")
Fixes: 5b8d5429da ("bridge: netlink: register netdevice before executing changelink")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a new type of chunk is added, the corresp conversion in
sctp_cname should be added. Otherwise, in some places, pr_debug
will print it as "unknown chunk".
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when reneging events in sctp_ulpq_renege(), the variable freed
could be increased by a __u16 value twice while freed is of __u16
type. It means freed may overflow at the second addition.
This patch is to fix it by using __u32 type for 'freed', while at
it, also to remove 'if (chunk)' check, as all renege commands are
generated in sctp_eat_data and it can't be NULL.
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the order of mac_up and sgmii_open for the
reasons noted below:
- If open takes more time(if the SGMII block is not responding or
if we want to do some delay based task) in this situation we
will hit NETDEV watchdog
- The main reason : We should signal to upper layers that we are
ready to receive packets "only" when the entire path is initialized
not the other way around, this is followed in the reset path where
we do mac_down, sgmii_reset and mac_up. This also makes the driver
uniform across the reset and open paths.
- In the future there may be need for delay based tasks to be done in
sgmii open which will result in NETDEV watchdog
- As per the documentation the order of init should be sgmii, mac, rings
and DMA
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
88E1145 also need this autoneg errata.
Fixes: f289978835 ("net: phy: marvell: Limit errata to 88m1101")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A group member going into state LEAVING should never go back to any
other state before it is finally deleted. However, this might happen
if the socket needs to send out a RECLAIM message during this interval.
Since we forget to remove the leaving member from the group's 'active'
or 'pending' list, the member might be selected for reclaiming, change
state to RECLAIMING, and get stuck in this state instead of being
deleted. This might lead to suppression of the expected 'member down'
event to the receiver.
We fix this by removing the member from all lists, except the RB tree,
at the moment it goes into state LEAVING.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group messages are not supposed to be returned to sender when the
destination socket disappears. This is done correctly for regular
traffic messages, by setting the 'dest_droppable' bit in the header.
But we forget to do that in group protocol messages. This has the effect
that such messages may sometimes bounce back to the sender, be perceived
as a legitimate peer message, and wreak general havoc for the rest of
the session. In particular, we have seen that a member in state LEAVING
may go back to state RECLAIMED or REMITTED, hence causing suppression
of an otherwise expected 'member down' event to the user.
We fix this by setting the 'dest_droppable' bit even in group protocol
messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2017-12-17
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a corner case in generic XDP where we have non-linear skbs
but enough tailroom in the skb to not miss to linearizing there,
from Song.
2) Fix BPF JIT bugs in s390x and ppc64 to not recache skb data when
BPF context is not skb, from Daniel.
3) Fix a BPF JIT bug in sparc64 where recaching skb data after helper
call would use the wrong register for the skb, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Brivio says:
Commit a985343ba9 ("vxlan: refactor verification and
application of configuration") introduced a change in the
behaviour of initial MTU setting: earlier, the MTU for a link
created on top of a given lower device, without an initial MTU
specification, was set to the MTU of the lower device minus
headroom as a result of this path in vxlan_dev_configure():
if (!conf->mtu)
dev->mtu = lowerdev->mtu -
(use_ipv6 ? VXLAN6_HEADROOM : VXLAN_HEADROOM);
which is now gone. Now, the initial MTU, in absence of a
configured value, is simply set by ether_setup() to ETH_DATA_LEN
(1500 bytes).
This breaks userspace expectations in case the MTU of
the lower device is higher than 1500 bytes minus headroom.
This patch restores the previous behaviour on newlink operation. Since
max_mtu can be negative and we update dev->mtu directly, also check it
for valid minimum.
Reported-by: Junhan Yan <juyan@redhat.com>
Fixes: a985343ba9 ("vxlan: refactor verification and application of configuration")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One example of when an ICMPv6 packet is required to be looped back is
when a host acts as both a Multicast Listener and a Multicast Router.
A Multicast Router will listen on address ff02::16 for MLDv2 messages.
Currently, MLDv2 messages originating from a Multicast Listener running
on the same host as the Multicast Router are not being delivered to the
Multicast Router. This is due to dst.input being assigned the default
value of dst_discard.
This results in the packet being looped back but discarded before being
delivered to the Multicast Router.
This patch sets dst.input to ip6_input to ensure a looped back packet
is delivered to the Multicast Router.
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix for SELinux on the umad SMI path. Some old hardware
does not fill the PKey properly exposing another bug in the newer
SELinux code.
- Check the input port as we can exceed array bounds from this
user supplied value
- Users are unable to use the hash field support as they want due to
incorrect checks on the field restrictions, correct that so the
feature works as intended
- User triggerable oops in the NETLINK_RDMA handler
- cxgb4 driver fix for a bad interaction with CQ flushing in iser
caused by patches in this merge window, and bad CQ flushing during
normal close.
- Unbalanced memalloc_noio in ipoib in an error path.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oyIl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"More fixes from testing done on the rc kernel, including more SELinux
testing. Looking forward, lockdep found regression today in ipoib
which is still being fixed.
Summary:
- Fix for SELinux on the umad SMI path. Some old hardware does not
fill the PKey properly exposing another bug in the newer SELinux
code.
- Check the input port as we can exceed array bounds from this user
supplied value
- Users are unable to use the hash field support as they want due to
incorrect checks on the field restrictions, correct that so the
feature works as intended
- User triggerable oops in the NETLINK_RDMA handler
- cxgb4 driver fix for a bad interaction with CQ flushing in iser
caused by patches in this merge window, and bad CQ flushing during
normal close.
- Unbalanced memalloc_noio in ipoib in an error path"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/ipoib: Restore MM behavior in case of tx_ring allocation failure
iw_cxgb4: only insert drain cqes if wq is flushed
iw_cxgb4: only clear the ARMED bit if a notification is needed
RDMA/netlink: Fix general protection fault
IB/mlx4: Fix RSS hash fields restrictions
IB/core: Don't enforce PKey security on SMI MADs
IB/core: Bound check alternate path port number
Pull i2c fixes from Wolfram Sang:
"Two bugfixes for the AT24 I2C eeprom driver and some minor corrections
for I2C bus drivers"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: piix4: Fix port number check on release
i2c: stm32: Fix copyrights
i2c-cht-wc: constify platform_device_id
eeprom: at24: change nvmem stride to 1
eeprom: at24: fix I2C device selection for runtime PM
Stable bugfixes:
- NFS: Avoid a BUG_ON() in nfs_commit_inode() by not waiting for a
commit in the case that there were no commit requests.
- SUNRPC: Fix a race in the receive code path
Other fixes:
- NFS: Fix a deadlock in nfs client initialization
- xprtrdma: Fix a performance regression for small IOs
-----BEGIN PGP SIGNATURE-----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=XhEC
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.15-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"This has two stable bugfixes, one to fix a BUG_ON() when
nfs_commit_inode() is called with no outstanding commit requests and
another to fix a race in the SUNRPC receive codepath.
Additionally, there are also fixes for an NFS client deadlock and an
xprtrdma performance regression.
Summary:
Stable bugfixes:
- NFS: Avoid a BUG_ON() in nfs_commit_inode() by not waiting for a
commit in the case that there were no commit requests.
- SUNRPC: Fix a race in the receive code path
Other fixes:
- NFS: Fix a deadlock in nfs client initialization
- xprtrdma: Fix a performance regression for small IOs"
* tag 'nfs-for-4.15-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Fix a race in the receive code path
nfs: don't wait on commit in nfs_commit_inode() if there were no commit requests
xprtrdma: Spread reply processing over more CPUs
nfs: fix a deadlock in nfs client initialization
This reverts commits 5c9d2d5c26, c7da82b894, and e7fe7b5cae.
We'll probably need to revisit this, but basically we should not
complicate the get_user_pages_fast() case, and checking the actual page
table protection key bits will require more care anyway, since the
protection keys depend on the exact state of the VM in question.
Particularly when doing a "remote" page lookup (ie in somebody elses VM,
not your own), you need to be much more careful than this was. Dave
Hansen says:
"So, the underlying bug here is that we now a get_user_pages_remote()
and then go ahead and do the p*_access_permitted() checks against the
current PKRU. This was introduced recently with the addition of the
new p??_access_permitted() calls.
We have checks in the VMA path for the "remote" gups and we avoid
consulting PKRU for them. This got missed in the pkeys selftests
because I did a ptrace read, but not a *write*. I also didn't
explicitly test it against something where a COW needed to be done"
It's also not entirely clear that it makes sense to check the protection
key bits at this level at all. But one possible eventual solution is to
make the get_user_pages_fast() case just abort if it sees protection key
bits set, which makes us fall back to the regular get_user_pages() case,
which then has a vma and can do the check there if we want to.
We'll see.
Somewhat related to this all: what we _do_ want to do some day is to
check the PAGE_USER bit - it should obviously always be set for user
pages, but it would be a good check to have back. Because we have no
generic way to test for it, we lost it as part of moving over from the
architecture-specific x86 GUP implementation to the generic one in
commit e585513b76 ("x86/mm/gup: Switch GUP to the generic
get_user_page_fast() implementation").
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.
2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
Brueckner.
3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
Berg.
4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.
5) Don't advertise gigabit in sh_eth when not available, from Thomas
Petazzoni.
6) Check network namespace when delivering to netlink taps, from Kevin
Cernekee.
7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.
8) Use correct address in TCP md5 lookups when replying to an incoming
segment, from Christoph Paasch.
9) Add schedule points to BPF map alloc/free, from Eric Dumazet.
10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
from Eric Dumazet.
11) Fix SKB leak in tipc, from Jon Maloy.
12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.
13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.
14) Add some new qmi_wwan device IDs, from Daniele Palmas.
15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: qcom/emac: Reduce timeout for mdio read/write
net: sched: fix static key imbalance in case of ingress/clsact_init error
net: sched: fix clsact init error path
ip_gre: fix wrong return value of erspan_rcv
net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
pkt_sched: Remove TC_RED_OFFLOADED from uapi
net: sched: Move to new offload indication in RED
net: sched: Add TCA_HW_OFFLOAD
net: aquantia: Increment driver version
net: aquantia: Fix typo in ethtool statistics names
net: aquantia: Update hw counters on hw init
net: aquantia: Improve link state and statistics check interval callback
net: aquantia: Fill in multicast counter in ndev stats from hardware
net: aquantia: Fill ndev stat couters from hardware
net: aquantia: Extend stat counters to 64bit values
net: aquantia: Fix hardware DMA stream overload on large MRRS
net: aquantia: Fix actual speed capabilities reporting
sock: free skb in skb_complete_tx_timestamp on error
s390/qeth: update takeover IPs after configuration change
s390/qeth: lock IP table while applying takeover changes
...
Here are some USB fixes for 4.15-rc4.
There is the usual handful gadget/dwc2/dwc3 fixes as always, for
reported issues. But the most important things in here is the core fix
from Alan Stern to resolve a nasty security bug (my first attempt is
reverted, Alan's was much cleaner), as well as a number of usbip fixes
from Shuah Khan to resolve those reported security issues.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWjQaXQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylt5ACdERNVQBbVoMadU97CUw/btE0FFtAAnjWr0xVn
hzlFdbbueTSIJqsp+G4H
=fjyL
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 4.15-rc4.
There is the usual handful gadget/dwc2/dwc3 fixes as always, for
reported issues. But the most important things in here is the core fix
from Alan Stern to resolve a nasty security bug (my first attempt is
reverted, Alan's was much cleaner), as well as a number of usbip fixes
from Shuah Khan to resolve those reported security issues.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: core: prevent malicious bNumInterfaces overflow
Revert "USB: core: only clean up what we allocated"
USB: core: only clean up what we allocated
Revert "usb: gadget: allow to enable legacy drivers without USB_ETH"
usb: gadget: webcam: fix V4L2 Kconfig dependency
usb: dwc2: Fix TxFIFOn sizes and total TxFIFO size issues
usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3
usb: dwc3: of-simple: set dev_pm_ops
usb: dwc3: of-simple: fix missing clk_disable_unprepare
usb: dwc3: gadget: Wait longer for controller to end command processing
usb: xhci: fix TDS for MTK xHCI1.1
xhci: Don't add a virt_dev to the devs array before it's fully allocated
usbip: fix stub_send_ret_submit() vulnerability to null transfer_buffer
usbip: prevent vhci_hcd driver from leaking a socket pointer address
usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input
usbip: fix stub_rx: get_pipe() to validate endpoint number
tools/usbip: fixes potential (minor) "buffer overflow" (detected on recent gcc with -Werror)
USB: uas and storage: Add US_FL_BROKEN_FUA for another JMicron JMS567 ID
usb: musb: da8xx: fix babble condition handling
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 4.15-rc4.
One patch for the ccree driver to prevent an unitialized value from
being returned to a caller, and the other fixes a logic error in the
pi433 driver"
* tag 'staging-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: pi433: Fixes issue with bit shift in rf69_get_modulation
staging: ccree: Uninitialized return in ssi_ahash_import()
Fixes two issues in the latest kernel.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaMs2CAAoJECgfDbjSjVRpUIgIAKxKE1Q/kK5ySNTCmbDUE5h7
XUtsKBqP9iwGaICVrlwcK0VZ6wq7ljwJIks9wBWRCu0AelbSm24VrbM5aZh8S6ij
JOesH4qhTpeqeCD/IC16hTYEtg2FOElgYbnAPEOLlJihUvuJWn2xgXD6Ci2YXyKg
waokN/7uTwB/i3tn67JZ2k5ICeaCYG4QhKzFy8cB3ktn1AcI3BD2iB/tzpzPBVQM
SIh+OYytc4MUnDKaa5s6wVHfnBLuxn9j98K6NwTXZbyHsIcw5sFKid/2y2B0u2BE
WUy4tYPJbzUGnQliuTKk2WQ1lo2XfiicgJ+BM2/7SEYJcqKFQd1j328UXID04sw=
=yIX/
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio regression fixes from Michael Tsirkin:
"Fixes two issues in the latest kernel"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_mmio: fix devm cleanup
ptr_ring: fix up after recent ptr_ring changes
- Fix various targets to dm_register_target after module __init
resources created; otherwise racing lvm2 commands could result in a
NULL pointer during initialization of associated DM kernel module.
- Fix regression in bio-based DM multipath queue_if_no_path handling.
- Fix DM bufio's shrinker to reclaim more than one buffer per scan.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaNBomAAoJEMUj8QotnQNao5IH/0X0Auycfx2O8dkVoRhW1Q3x
NNt7m6aKhmdUsBYOug9/na5kNKqsRzKyPYSV9bM0Cy5mJzgxQYMeL5Tmu2qwGDOL
1C/HUhffmZJQ+lK5dS2wQ41Ep+lppm8KYofJ70Ueb+JQ9Uxmkp9GXGud0LrJ0QzR
9D5i/3jAlZuOnGLQ0+Q0E9wXa8sQdfrAbcPzz+4nG9aqGcz2T5lfbwg1K+Ym0U3r
0jBAHZWhamJQP1gW1+i0EWWtR68TgaWbHeTjrdvm2pUueAaywJzP9oeK++p3Op+9
A2JRE3I4ClAkUBjj480UAJW8Egg6zZ1mfOKta/CpqChbVqqjANi9lGSyRlkYMFg=
=oNN+
-----END PGP SIGNATURE-----
Merge tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- fix a particularly nasty DM core bug in a 4.15 refcount_t conversion.
- fix various targets to dm_register_target after module __init
resources created; otherwise racing lvm2 commands could result in a
NULL pointer during initialization of associated DM kernel module.
- fix regression in bio-based DM multipath queue_if_no_path handling.
- fix DM bufio's shrinker to reclaim more than one buffer per scan.
* tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm bufio: fix shrinker scans when (nr_to_scan < retain_target)
dm mpath: fix bio-based multipath queue_if_no_path handling
dm: fix various targets to dm_register_target after module __init resources created
dm table: fix regression from improper dm_dev_internal.count refcount_t conversion
The most important one is the bfa fix because it's easy to oops the
kernel with this driver (this includes the commit that corrects the
compiler warning in the original), a regression in the new timespec
conversion in aacraid and a regression in the Fibre Channel ELS
handling patch. The other three are a theoretical problem with
termination in the vendor/host matching code and a use after free in
lpfc.
The additional patches are a fix for an I/O hang in the mq code under
certain circumstances and a rare oops in some debugging code.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=9sav
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The most important one is the bfa fix because it's easy to oops the
kernel with this driver (this includes the commit that corrects the
compiler warning in the original), a regression in the new timespec
conversion in aacraid and a regression in the Fibre Channel ELS
handling patch.
The other three are a theoretical problem with termination in the
vendor/host matching code and a use after free in lpfc.
The additional patches are a fix for an I/O hang in the mq code under
certain circumstances and a rare oops in some debugging code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Fix a scsi_show_rq() NULL pointer dereference
scsi: MAINTAINERS: change FCoE list to linux-scsi
scsi: libsas: fix length error in sas_smp_handler()
scsi: bfa: fix type conversion warning
scsi: core: run queue if SCSI device queue isn't ready and queue is idle
scsi: scsi_devinfo: cleanly zero-pad devinfo strings
scsi: scsi_devinfo: handle non-terminated strings
scsi: bfa: fix access to bfad_im_port_s
scsi: aacraid: address UBSAN warning regression
scsi: libfc: fix ELS request handling
scsi: lpfc: Use after free in lpfc_rq_buf_free()
- Fix use of uninitialized drv_typ variable
- Apply NO_CMD23 quirk to some specific SD cards to make them work
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rovh
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes:
- fix use of uninitialized drv_typ variable
- apply NO_CMD23 quirk to some specific SD cards to make them work"
* tag 'mmc-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: apply NO_CMD23 quirk to some specific cards
mmc: core: properly init drv_type
Pull overlayfs fixes from Miklos Szeredi:
- fix incomplete syncing of filesystem
- fix regression in readdir on ovl over 9p
- only follow redirects when needed
- misc fixes and cleanups
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix overlay: warning prefix
ovl: Use PTR_ERR_OR_ZERO()
ovl: Sync upper dirty data when syncing overlayfs
ovl: update ctx->pos on impure dir iteration
ovl: Pass ovl_get_nlink() parameters in right order
ovl: don't follow redirects if redirect_dir=off
