The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the omap2_dpll_round_rate routine attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Standby status is provided for certain clkctrl clocks to see if the
given module has entered standby or not. This is mostly needed by
remoteproc code to see if the remoteproc has entered standby and the clock
can be turned off safely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
RNG and TIMER12 are reserved for secure side usage only on HS devices,
so disable their clkctrl clocks on HS SoCs also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is one instance outside the TI clock driver that needs the info
whether a clock is an OMAP HW clock or not. Thus, move the function
declaration into the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Multiple users might deny autoidle on a clock. So we should have some
counting here, also according to the comment in _setup_iclk_autoidle().
Also setting autoidle regs is not atomic, so there is another reason
for locking.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Currently, only one clkctrl node can be added under a specific CM node
due to limitation with the implementation. Modify the code to pick-up
clockdomain name from the clkctrl node instead of CM node if provided.
Also, add a new flag to the TI clock driver so that both modes can
be supported simultaneously.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----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=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
Control module can have multiple instances in a system, each with separate
address space and features. Add base support for these auxiliary instances,
with support for syscon and clock mappings under them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Useful for changing few bits on a register, this makes sure for example
that the operation is done atomically in case of syscon.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Currently, TI clock driver uses an encapsulated struct that is cast into
a void pointer to store all register addresses. This can be considered
as rather nasty hackery, and prevents from expanding the register
address field also. Instead, replace all the code to use proper struct
in place for this, which contains all the previously used data.
This patch is rather large as it is touching multiple files, but this
can't be split up as we need to avoid any boot breakage.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This has been superceded by the usage of ti_clk_ll_ops for now.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This is not needed outside the driver, so move it inside it and remove
the prototype from the public header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This will be needed to move some additional clockdomain functionality
under clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Clksel support has been deprecated a while back, so remove these from
the struct also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
DPLLs typically have a maximum rate they can support, and this varies
from DPLL to DPLL. Add support of the maximum rate value to the DPLL
data struct, and also add check for this in the DPLL round_rate function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Convert DPLL support code to use clk_hw pointers for reference and bypass
clocks. This allows us to use clk_hw_* APIs for accessing any required
parameters for these clocks, avoiding some locking problems at least with
DPLL enable code; this used clk_get_rate which uses mutex but isn't
good under clk_enable / clk_disable.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform so these
can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W+es
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
On dm814x we have some clocks at DPLLS and some at PRCM. Let's add a new
omap_prcm_init_data entry for the DPLLS so we can initalize timer clocks
early.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
Let's add a minimal clocks for dm814x to get it booted. This is
mostly a placeholder and relies on the PLLs being on from the
bootloader.
Note that the divider clocks work the same way as on dm816x and
am335x.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With most of the clock code under clock driver already, the low-level
register access code, and the init code for the same, is no longer
needed outside the clock driver. Thus, these can be moved under clock
driver also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We should avoid exporting data from drivers, instead use an API for
registering the clock low level operations.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Several exported TI clock driver features are no longer needed outside
the clock driver itself, thus move all of these to the driver private
header file. Also, update some of the driver files to actually include
this header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With legacy clock support gone, this is no longer needed under platform,
so move it under the clock driver itself. Make some exports be driver
internal definitions at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove unnecessary declarations
from the TI clock header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove the exported clock driver
APIs as well, as these are not needed outside clock driver anymore.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, this is no longer needed under
platform code-base. Thus, move this under the TI clock driver, and
remove the exported API from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy support gone, OMAP2+ default gate clock can be moved
under clock driver. Create a new file for the purpose, and clean-up
the header exports a bit as some clock APIs are no longer needed
outside clock driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
clkdm_control is used to determine, whether clocks should trigger a
clockdomain transition when they are enabled/disabled. Keep this
functionality intact, but replace this with a clk_features flag
which can be initialized during boot if needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, OMAP3 generic DPLL code can now be
moved over to the clock driver also. A few un-unused clkoutx2 functions
are also removed at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clock driver requires access to some CM API functions once the code
is being moved under the clock driver from the platform directory.
Gate type clock requires access to cm_wait_module_ready and
cm_split_idlest_reg functions, which are both used for waiting until
the module being clocked has been successfully activated. These CM
APIs are now exported through the ti_clk_ll_ops struct.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clock driver requires access to certain clockdomain handling ops once
the code is being moved over under clock driver. Example of this is
clk_enable / clk_disable under omap3 DPLL code. The required clkdm
APIs are now exported through the ti_clk_ll_ops struct.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer used outside clock driver, so move it under the driver
and remove the export for it from the global header file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer needed in platform directory, as the legacy clock data
is gone, so move it under TI clock driver. Some static functions are
renamed also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP interface clock implementation
can be moved under the clock driver. Some temporary header file tweaks are
also needed to make this change work properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP4 specific DPLL implementations
can be moved under the clock driver. Change some of the function prototypes
to be static at the same time, and remove some exports from the global TI
clock driver header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data now gone, we can start moving OMAP clock
type implementations under clock driver. Start this with moving the
generic OMAP DPLL clock type under TI clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver support code is going to be moved under
drivers/clk/ti, an API for setting / getting the SoC specific clock
features is needed. This patch provides this API and changes the
existing code to use it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Splits the clock related provider module inits under their own driver files.
Previously this was done for all modules under the common PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
All clock provider related drivers will now register their iomaps
with a static index. This makes it easier to split up the individual
drivers to their own files in subsequent patches.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The 'ARM: OMAP3: legacy clock data move under clk driver' patch series
causes build errors when CONFIG_OMAP3 is not set:
drivers/clk/ti/dpll.c: In function 'ti_clk_register_dpll':
drivers/clk/ti/dpll.c:199:31: error: 'omap3_dpll_ck_ops' undeclared (first use in this function)
const struct clk_ops *ops = &omap3_dpll_ck_ops;
^
drivers/clk/ti/dpll.c:199:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/clk/ti/dpll.c:259:10: error: 'omap3_dpll_per_ck_ops' undeclared (first use in this function)
ops = &omap3_dpll_per_ck_ops;
^
drivers/built-in.o: In function `ti_clk_register_gate':
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_omap3430es2_dss_usbhost_wait'
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_am35xx_ipss_module_wait'
-in.o: In function `ti_clk_register_interface':
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_hsotgusb_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_dss_usbhost_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_ssi_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_am35xx_ipss_wait'
drivers/built-in.o: In function `ti_clk_register_composite':
:(.text+0x3da768): undefined reference to `ti_clk_build_component_gate'
In order to fix that problem, this patch makes the omap3 legacy code
compiled only when both CONFIG_OMAP3 and CONFIG_ATAGS are set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
Introduces omap3 legacy clock data under clock driver. The clock data
is also in new format, which makes it possible to get rid of the
clk-private.h header. This patch also introduces SoC specific init
functions that shall be called from the low level init.
The data format used in this file has two possible evolution paths;
it can either be removed completely once no longer needed, or it will
be possible to retain the format and modify the TI clock driver to be
a loadable module at some point. The actual path to be followed
will be decided later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These modules don't need to include clk-private.h. Replace the
include with clk.h because these modules are clock consumers and
also include clk-provider.h in clk/ti.h because struct
clk_hw_omap has a struct clk_hw embedded in it.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
While the change for determine_rate clock operation was merged,
the OMAP counterpart using these calls was overlooked for some reason,
and caused boot failures on at least OMAP4 platforms. Fixed by updating
the DPLL API calls to use the new parameters.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Fixes: 646cafc6aa ("clk: Change clk_ops->determine_rate")
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Expand the support of omap4 per-dpll to provide set_rate_and_parent.
This is required for proper behavior of clk_change_rate with
determine_rate support.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
