The SERDES lane control mux registers are present in the
CTRLMMR space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-3-rogerq@ti.com
There are 4 lanes in each J7200 SERDES. Each SERDES lane mux can
select upto 4 different IPs. Define all the possible functions.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200930122032.23481-2-rogerq@ti.com
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200916155715.21009-7-krzk@kernel.org
Add support for the eMMC and SD card connected on the common
processor board
sdhci0 is connected to an eMMC while sdhci1 is connected to the
micro SD slot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200924112644.11076-3-faiz_abbas@ti.com
Add support for MMC/SD controller nodes present on TI's j7200 SoCs.
There are two nodes:
1. sdhci0 (8 bit bus width, 200 MHz, HS200, 200 MBps)
2. sdhci1 (4 bit bus width, 50 MHz, HS, 25 MBps)
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200924112644.11076-2-faiz_abbas@ti.com
J7200 SoM has a HyperFlash connected to HyperBus memory controller. But
HyperBus is muxed with OSPI, therefore keep HyperBus node disabled.
Bootloader will detect the mux and enable the node as required.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200923163150.16973-3-vigneshr@ti.com
J7200 has a Flash SubSystem that has one OSPI and one HyperBus.. Add
DT nodes for HyperBus controller for now.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200923163150.16973-2-vigneshr@ti.com
Add DT nodes for I2C GPIO expanders on main_i2c0 and main_i2c1 and
also add the pinmux corresponding to these I2C instances.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923155400.13757-3-vigneshr@ti.com
J7200 has 7 I2Cs in main domain, 2 I2Cs in MCU and 1 in wakeup domain.
Add DT nodes for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923155400.13757-2-vigneshr@ti.com
The TI J7200 EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI J7200 SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200923220938.30788-5-grygorii.strashko@ti.com
Add the ringacc and udmap nodes for Main and MCU NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200923220938.30788-2-grygorii.strashko@ti.com
Add support for J7200 Common Processor Board.
The EVM architecture is very similar to J721E as follows:
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality.
Note:
* The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
* Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
* All daughter cards beyond the basic boards shall be maintained as
overlays.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-6-lokeshvutla@ti.com
The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
It is targeted for automotive gateway, vehicle compute systems,
Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
The SoC aims to meet the complex processing needs of modern embedded
products.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, two clusters of lockstep
capable dual Cortex-R5F MCUs and a Centralized Device Management and
Security Controller (DMSC).
* Configurable L3 Cache and IO-coherent architecture with high data
throughput capable distributed DMA architecture under NAVSS.
* Integrated Ethernet switch supporting up to a total of 4 external ports
in addition to legacy Ethernet switch of up to 2 ports.
* Upto 1 PCIe-GEN3 controller, 1 USB3.0 Dual-role device subsystems,
20 MCANs, 3 McASP, eMMC and SD, OSPI/HyperBus memory controller, I3C
and I2C, eCAP/eQEP, eHRPWM among other peripherals.
* One hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-5-lokeshvutla@ti.com
The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
It is targeted for automotive gateway, vehicle compute systems,
Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
The SoC aims to meet the complex processing needs of modern embedded
products.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, two clusters of lockstep
capable dual Cortex-R5F MCUs and a Centralized Device Management and
Security Controller (DMSC).
* Configurable L3 Cache and IO-coherent architecture with high data
throughput capable distributed DMA architecture under NAVSS.
* Integrated Ethernet switch supporting up to a total of 4 external ports
in addition to legacy Ethernet switch of up to 2 ports.
* Upto 1 PCIe-GEN3 controller, 1 USB3.0 Dual-role device subsystems,
20 MCANs, 3 McASP, eMMC and SD, OSPI/HyperBus memory controller, I3C and
I2C, eCAP/eQEP, eHRPWM among other peripherals.
* One hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200914162231.2535-4-lokeshvutla@ti.com
J721E Common Processor Board has PCIe connectors for the 1st three PCIe
instances. Configure the three PCIe instances in RC mode and disable the
4th PCIe instance.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200914152115.1788-3-kishon@ti.com
Add PCIe device tree nodes (both RC and EP) for the four
PCIe instances here.
Also add the missing translations required in the "ranges"
DT property of cbass_main to access all the four PCIe
instances.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200914152115.1788-2-kishon@ti.com
We intend to use one header file for SERDES MUX for all
TI SoCs so rename the header file.
The exsting macros are too generic. Prefix them with SoC name.
While at that, add the missing configurations for completeness.
Fixes: b766e3b0d5 ("arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES lane mux")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200918165930.2031-1-rogerq@ti.com
Building with W=2 throws up a bunch of easy to fixup warnings..
node_name_chars_strict is one of them.. Knock those out.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200903130015.21361-9-nm@ti.com
serdes and ehrpwm_tbclk nodes should be using clock@ naming for nodes
following standard conventions of device tree (section 2.2.2 Generic
Names recommendation in [1]).
[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200903130015.21361-5-nm@ti.com
Per errata i2104 documented in AM65x device errata document (TI document
number SPRZ452E, revised June 2019), Gen3 operation is not supported for
both PCIe Root Complex and Endpoint modes of operation.
See: https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
Restrict speed to Gen2 to address the errata.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20200802165356.10285-1-nsekhar@ti.com
Add a reserved memory node to reserve a portion of the DDR memory to be
used for performing inter-processor communication between all the remote
processors running RTOS on the TI J721E EVM boards. 28 MB of memory is
reserved for this purpose, and this accounts for all the vrings and vring
buffers between all the possible pairs of remote processors.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-9-s-anna@ti.com
Two carveout reserved memory nodes have been added for the lone C71x DSP
remote processor device present within the MAIN voltage domain for the TI
J721E EVM boards. These nodes are assigned to the respective rproc device
node as well. The first region will be used as the DMA pool for the rproc
device, and the second region will furnish the static carveout regions for
the firmware memory.
The current carveout addresses and sizes are defined statically for each
device. The C71x DSP processor does support a MMU called CMMU, but is not
currently supported and as such requires the exact memory used by the
firmware to be set-aside. The firmware images currently do not need any
RSC_CARVEOUT entries either in their resource tables to allocate the
memory for firmware memory segments.
The reserved memory nodes can be disabled later on if there is no use-case
defined to use the C71x DSP remoteproc processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-8-s-anna@ti.com
Add the required 'mboxes' property to the C71x DSP processor for the TI
J721E common processor board. The mailboxes and some shared memory are
required for running the Remote Processor Messaging (RPMsg) stack between
the host processor and each of the DSPs. The nodes are therefore added
in the common k3-j721e-som-p0.dtsi file so that all of these can be
co-located.
The chosen sub-mailboxes match the values used in the current firmware
images. This can be changed, if needed, as per the system integration
needs after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-7-s-anna@ti.com
The J721E SoCs have a single TMS320C71x DSP Subsystem in the MAIN
voltage domain containing the next-generation C711 CPU core. The
subsystem has 32 KB of L1D configurable SRAM/Cache and 512 KB of
L2 configurable SRAM/Cache. This subsystem has a CMMU but is not
used currently. The inter-processor communication between the main
A72 cores and the C711 processor is achieved through shared memory
and a Mailbox. Add the DT node for this DSP processor sub-system
in the common k3-j721e-main.dtsi file.
The following firmware name is used by default for the C71x core,
and can be overridden in a board dts file if desired:
C71x_0 DSP: j7-c71_0-fw
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-6-s-anna@ti.com
Two carveout reserved memory nodes each have been added for each of the
C66x DSP remote processor devices present within the MAIN voltage domain
for the TI J721E EVM boards. These nodes are assigned to the respective
rproc device nodes as well. The first region will be used as the DMA pool
for the rproc devices, and the second region will furnish the static
carveout regions for the firmware memory.
The minimum granularity on the Cache settings on C66x DSP cores is 16 MB,
so the DMA memory regions are chosen such that they are in separate 16 MB
regions for each DSP, while reserving a total of 16 MB for each DSP and
not changing the overall DSP remoteproc carveouts.
The current carveout addresses and sizes are defined statically for each
device. The C66x DSP processors do not have an MMU, and as such require the
exact memory used by the firmwares to be set-aside. The firmware images
do not require any RSC_CARVEOUT entries in their resource tables to
allocate the memory for firmware memory segments.
The reserved memory nodes can be disabled later on if there is no use-case
defined to use the corresponding remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-5-s-anna@ti.com
Add the required 'mboxes' property to both the C66x DSP processors for the
TI J721E common processor board. The mailboxes and some shared memory are
required for running the Remote Processor Messaging (RPMsg) stack between
the host processor and each of the DSPs. The nodes are therefore added
in the common k3-j721e-som-p0.dtsi file so that all of these can be
co-located.
The chosen sub-mailboxes match the values used in the current firmware
images. This can be changed, if needed, as per the system integration
needs after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-4-s-anna@ti.com
The J721E SoCs have two TMS320C66x DSP Core Subsystems (C66x CorePacs)
in the MAIN voltage domain, each with a C66x Fixed/Floating-Point DSP
Core, and 32 KB of L1P & L1D configurable SRAMs/Cache and an additional
288 KB of L2 configurable SRAM/Cache. These subsystems do not have
an MMU but contain a Region Address Translator (RAT) sub-module for
translating 32-bit processor addresses into larger bus addresses.
The inter-processor communication between the main A72 cores and
these processors is achieved through shared memory and Mailboxes.
Add the DT nodes for these DSP processor sub-systems in the common
k3-j721e-main.dtsi file.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if desired:
C66x_0 DSP: j7-c66_0-fw
C66x_1 DSP: j7-c66_1-fw
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-3-s-anna@ti.com
The commit eb9f9173d0 ("arm64: dts: ti: k3-j721e-common-proc-board:
Add IPC sub-mailbox nodes") has added the sub-mailbox nodes used by
various remote processors and disabled the unused mailbox clusters
directly in the k3-j721e-common-proc-board dts file. Move all of these
nodes into the k3-j721e-som-p0.dtsi file instead to co-locate all the
mailboxes and the soon to be added DDR reserved-memory carveout nodes
used by remoteprocs within the same dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200825172145.13186-2-s-anna@ti.com
The various CBASS interconnect nodes on K3 J721E SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200723211137.26641-3-s-anna@ti.com
The various CBASS interconnect nodes on K3 AM65x SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20200723211137.26641-2-s-anna@ti.com
Pull crypto fixes from Herbert Xu:
- fix regression in af_alg that affects iwd
- restore polling delay in qat
- fix double free in ingenic on error path
- fix potential build failure in sa2ul due to missing Kconfig dependency
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: af_alg - Work around empty control messages without MSG_MORE
crypto: sa2ul - add Kconfig selects to fix build error
crypto: ingenic - Drop kfree for memory allocated with devm_kzalloc
crypto: qat - add delay before polling mailbox
- Move disabling of the local APIC after invoking fixup_irqs() to ensure
that interrupts which are incoming are noted in the IRR and not ignored.
- Unbreak affinity setting. The rework of the entry code reused the
regular exception entry code for device interrupts. The vector number is
pushed into the errorcode slot on the stack which is then lifted into an
argument and set to -1 because that's regs->orig_ax which is used in
quite some places to check whether the entry came from a syscall. But it
was overlooked that orig_ax is used in the affinity cleanup code to
validate whether the interrupt has arrived on the new target. It turned
out that this vector check is pointless because interrupts are never
moved from one vector to another on the same CPU. That check is a
historical leftover from the time where x86 supported multi-CPU
affinities, but not longer needed with the now strict single CPU
affinity. Famous last words ...
- Add a missing check for an empty cpumask into the matrix allocator. The
affinity change added a warning to catch the case where an interrupt is
moved on the same CPU to a different vector. This triggers because a
condition with an empty cpumask returns an assignment from the allocator
as the allocator uses for_each_cpu() without checking the cpumask for
being empty. The historical inconsistent for_each_cpu() behaviour of
ignoring the cpumask and unconditionally claiming that CPU0 is in the
mask striked again. Sigh.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl9L6WYTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoRV5D/9dRq/4pn5g1esnzm4GhIr2To3Qp6cl
s7VswTdN8FmWBqVz79ZVYqj663UpL3pPY1np01ctrxRQLeDVfWcI2BMR5irnny8h
otORhFysuDUl+yfuomWVbzfQQNJ+VeQVeWKD3cIhD1I3sXqDX5Wpa8n086hYKQXx
eutVC3+JdzJZFm68xarlLW7h2f1au1eZZFgVnyY+J5KO9Dwm63a4RITdDVk7KV4t
uKEDza5P9SY+kE9LAGNq8BAEObf9FeMXw0mRM7atRKVsJQQGVk6bgiuaRr01w1+W
hQCPx/3g6PHFnGgx/KQgHf1jgrZFhXOyIDo6ZeFy+SJGIZRB3n8o5Kjns2l8Pa+K
2qy1TRoZIsGkwGCi/BM6viLzBikbh/gnGYy/8KTEJdKs8P3ZKHUZVSAB1dpapOWX
4n+rKoVPnvxgRSeZZo+tgLkvUdh+/9Huyr9vHiYjtbbB8tFvjlkOmrZ6sirHByDy
jg6TjOJVb1CC/PoW4M7JNfmeKvHQnTACwH6djdVGDLPJspuUsYkPI0Uk0CX21SA3
45Tuylvl9jT6+vq95Av2RbAiipmSpZ/O1NHV8Paf466SKmhUgG3lv5PHh3xTm1U2
Be/RbJ75x4Muuw42ttU1LcpcLPcOZRQNEREoNd5UysgYYgWRekBvU+ZRQNW4g2nw
3JDgJgm0iBUN9w==
=zIi4
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Three interrupt related fixes for X86:
- Move disabling of the local APIC after invoking fixup_irqs() to
ensure that interrupts which are incoming are noted in the IRR and
not ignored.
- Unbreak affinity setting.
The rework of the entry code reused the regular exception entry
code for device interrupts. The vector number is pushed into the
errorcode slot on the stack which is then lifted into an argument
and set to -1 because that's regs->orig_ax which is used in quite
some places to check whether the entry came from a syscall.
But it was overlooked that orig_ax is used in the affinity cleanup
code to validate whether the interrupt has arrived on the new
target. It turned out that this vector check is pointless because
interrupts are never moved from one vector to another on the same
CPU. That check is a historical leftover from the time where x86
supported multi-CPU affinities, but not longer needed with the now
strict single CPU affinity. Famous last words ...
- Add a missing check for an empty cpumask into the matrix allocator.
The affinity change added a warning to catch the case where an
interrupt is moved on the same CPU to a different vector. This
triggers because a condition with an empty cpumask returns an
assignment from the allocator as the allocator uses for_each_cpu()
without checking the cpumask for being empty. The historical
inconsistent for_each_cpu() behaviour of ignoring the cpumask and
unconditionally claiming that CPU0 is in the mask struck again.
Sigh.
plus a new entry into the MAINTAINER file for the HPE/UV platform"
* tag 'x86-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/matrix: Deal with the sillyness of for_each_cpu() on UP
x86/irq: Unbreak interrupt affinity setting
x86/hotplug: Silence APIC only after all interrupts are migrated
MAINTAINERS: Add entry for HPE Superdome Flex (UV) maintainers
- Revert the platform driver conversion of interrupt chip drivers as it
turned out to create more problems than it solves.
- Fix a trivial typo in the new module helpers which made probing reliably
fail.
- Small fixes in the STM32 and MIPS Ingenic drivers
- The TI firmware rework which had badly managed dependencies and had to
wait post rc1.
-----BEGIN PGP SIGNATURE-----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=guRc
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for interrupt chip drivers:
- Revert the platform driver conversion of interrupt chip drivers as
it turned out to create more problems than it solves.
- Fix a trivial typo in the new module helpers which made probing
reliably fail.
- Small fixes in the STM32 and MIPS Ingenic drivers
- The TI firmware rework which had badly managed dependencies and had
to wait post rc1"
* tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/ingenic: Leave parent IRQ unmasked on suspend
irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake
irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse
irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers
arm64: dts: k3-am65: Update the RM resource types
arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings
arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings
irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC
irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field
dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml
dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent.
irqchip/ti-sci-intr: Add support for INTR being a parent to INTR
dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml
dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent
firmware: ti_sci: Add support for getting resource with subtype
firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
firmware: ti_sci: Drop the device id to resource type translation
- Make is_idle_task() __always_inline to prevent the compiler from putting
it out of line into the wrong section because it's used inside noinstr
sections.
-----BEGIN PGP SIGNATURE-----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=oKWA
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single fix for the scheduler:
- Make is_idle_task() __always_inline to prevent the compiler from
putting it out of line into the wrong section because it's used
inside noinstr sections"
* tag 'sched-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Use __always_inline on is_idle_task()
- Prevent recursion by using raw_cpu_* operations
- Fixup the interrupt state in the cpu idle code to be consistent
- Push rcu_idle_enter/exit() invocations deeper into the idle path so
that the lock operations are inside the RCU watching sections
- Move trace_cpu_idle() into generic code so it's called before RCU goes
idle.
- Handle raw_local_irq* vs. local_irq* operations correctly
- Move the tracepoints out from under the lockdep recursion handling
which turned out to be fragile and inconsistent.
-----BEGIN PGP SIGNATURE-----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=Hgt6
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of fixes for lockdep, tracing and RCU:
- Prevent recursion by using raw_cpu_* operations
- Fixup the interrupt state in the cpu idle code to be consistent
- Push rcu_idle_enter/exit() invocations deeper into the idle path so
that the lock operations are inside the RCU watching sections
- Move trace_cpu_idle() into generic code so it's called before RCU
goes idle.
- Handle raw_local_irq* vs. local_irq* operations correctly
- Move the tracepoints out from under the lockdep recursion handling
which turned out to be fragile and inconsistent"
* tag 'locking-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep,trace: Expose tracepoints
lockdep: Only trace IRQ edges
mips: Implement arch_irqs_disabled()
arm64: Implement arch_irqs_disabled()
nds32: Implement arch_irqs_disabled()
locking/lockdep: Cleanup
x86/entry: Remove unused THUNKs
cpuidle: Move trace_cpu_idle() into generic code
cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED generic
sched,idle,rcu: Push rcu_idle deeper into the idle path
cpuidle: Fixup IRQ state
lockdep: Use raw_cpu_*() for per-cpu variables
-----BEGIN PGP SIGNATURE-----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=0PxR
-----END PGP SIGNATURE-----
Merge tag '5.9-rc2-smb-fix' of git://git.samba.org/sfrench/cifs-2.6
Pull cfis fix from Steve French:
"DFS fix for referral problem when using SMB1"
* tag '5.9-rc2-smb-fix' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix check of tcon dfs in smb1
