As kmem_caches share the same properties (size, allocation/free behaviour)
for all potential devices, we can use global caches. While this
potential has worse fragmentation behaviour (one can argue that
different devices would have different activity lifetimes, but you can
also argue that activity is temporal across the system) it is the
default behaviour of the system at large to amalgamate matching caches.
The benefit for us is much reduced pointer dancing along the frequent
allocation paths.
v2: Defer shrinking until after a global grace period for futureproofing
multiple consumers of the slab caches, similar to the current strategy
for avoiding shrinking too early.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190228102035.5857-1-chris@chris-wilson.co.uk
Other than LPT, no other PCH needed to differentiate between
LP and HP. So let's remove this before we spread this mistake
to future platforms.
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221211716.9433-1-rodrigo.vivi@intel.com
On skl the crc registers were extended to provide plane crcs
for up to 7 planes. Add the new crc sources.
The current code uses the ivb+ register definitions for skl+
which does happen to work as the plane1, plane2, and dmux/pf
bits happen the match what ivb+ had. So no bug in the current
code.
v2: Drop the unused set_wa parameter (DK)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190214192219.3858-4-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Defining the mei-i915 interface functions and initialization of
the interface.
v2:
Adjust to the new interface changes. [Tomas]
Added further debug logs for the failures at MEI i/f.
port in hdcp_port data is equipped to handle -ve values.
v3:
mei comp is matched for global i915 comp master. [Daniel]
In hdcp_shim hdcp_protocol() is replaced with const variable. [Daniel]
mei wrappers are adjusted as per the i/f change [Daniel]
v4:
port initialization is done only at hdcp2_init only [Danvet]
v5:
I915 registers a subcomponent to be matched with mei_hdcp [Daniel]
v6:
HDCP_disable for all connectors incase of comp_unbind.
Tear down HDCP comp interface at i915_unload [Daniel]
v7:
Component init and fini are moved out of connector ops [Daniel]
hdcp_disable is not called from unbind. [Daniel]
v8:
subcomponent name is dropped as it is already merged.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> [v11]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1550338640-17470-5-git-send-email-ramalingam.c@intel.com
At a few points in our uABI, we check to see if the driver is wedged and
report -EIO back to the user in that case. However, as we perform the
check and reset asynchronously (where once before they were both
serialised by the struct_mutex), we may instead see the temporary wedging
used to cancel inflight rendering to avoid a deadlock during reset
(caused by either us timing out in our reset handler,
i915_wedge_on_timeout or with malice aforethought in intel_reset_prepare
for a stuck modeset). If we suspect this is the case, that is we see a
wedged driver *and* reset in progress, then wait until the reset is
resolved before reporting upon the wedged status.
v2: might_sleep() (Mika)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109580
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220145637.23503-1-chris@chris-wilson.co.uk
As time goes by, usage of generic ioctls such as drm_syncobj and
sync_file are on the increase bypassing i915-specific ioctls like
GEM_WAIT. Currently, we only apply waitboosting to our driver ioctls as
we track the file/client and account the waitboosting to them. However,
since commit 7b92c1bd05 ("drm/i915: Avoid keeping waitboost active for
signaling threads"), we no longer have been applying the client
ratelimiting on waitboosts and so that information has only been used
for debug tracking.
Push the application of waitboosting down to the common
i915_request_wait, and apply it to all foreign fence waits as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190213092504.25709-1-chris@chris-wilson.co.uk
Previously, we were able to rely on the recursive properties of
struct_mutex to allow us to serialise revoking mmaps and reacquiring the
FENCE registers with them being clobbered over a global device reset.
I then proceeded to throw out the baby with the bath water in order to
pursue a struct_mutex-less reset.
Perusing LWN for alternative strategies, the dilemma on how to serialise
access to a global resource on one side was answered by
https://lwn.net/Articles/202847/ -- Sleepable RCU:
1 int readside(void) {
2 int idx;
3 rcu_read_lock();
4 if (nomoresrcu) {
5 rcu_read_unlock();
6 return -EINVAL;
7 }
8 idx = srcu_read_lock(&ss);
9 rcu_read_unlock();
10 /* SRCU read-side critical section. */
11 srcu_read_unlock(&ss, idx);
12 return 0;
13 }
14
15 void cleanup(void)
16 {
17 nomoresrcu = 1;
18 synchronize_rcu();
19 synchronize_srcu(&ss);
20 cleanup_srcu_struct(&ss);
21 }
No more worrying about stop_machine, just an uber-complex mutex,
optimised for reads, with the overhead pushed to the rare reset path.
However, we do run the risk of a deadlock as we allocate underneath the
SRCU read lock, and the allocation may require a GPU reset, causing a
dependency cycle via the in-flight requests. We resolve that by declaring
the driver wedged and cancelling all in-flight rendering.
v2: Use expedited rcu barriers to match our earlier timing
characteristics.
v3: Try to annotate locking contexts for sparse
v4: Reduce selftest lock duration to avoid a reset deadlock with fences
v5: s/srcu/reset_backoff_srcu/
v6: Remove more stale comments
Testcase: igt/gem_mmap_gtt/hang
Fixes: eb8d0f5af4 ("drm/i915: Remove GPU reset dependence on struct_mutex")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208153708.20023-2-chris@chris-wilson.co.uk
Changing the i915_edp_psr_debug was enabling, disabling or switching
PSR version by directly calling intel_psr_disable_locked() and
intel_psr_enable_locked(), what is not the default PSR path that will
be executed by real users.
So lets force a fastset in the PSR CRTC to trigger a pipe update and
stress the default code path.
Recently a bug was found when switching from PSR2 to PSR1 while
enable_psr kernel parameter was set to the default parameter, this
changes fix it and also fixes the bug linked bellow were DRRS was
left enabled together with PSR when enabling PSR from debugfs.
v2: Handling missing case: disabled to PSR1
v3: Not duplicating the whole atomic state(Maarten)
v4: Adding back the missing call to intel_psr_irq_control(Dhinakaran)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108341
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206211845.5322-1-jose.souza@intel.com
Split the color management hooks along the single vs. double
buffered registers line. Of the currently programmed registers
GAMMA_MODE and the ilk+ pipe CSC are double buffered, the
LUTS and CHV CGM block are single buffered.
The double buffered register will be programmed during the
normal pipe update with evasion, and also during pipe enable
so that the settings will already be correct when the pipe
starts up before the planes are enabled.
The single buffered registers are currently programmed before
the vblank evade. Which is totally wrong, but we'll correct
that later.
v2: Add some docs to explain the two vfuncs (Matt,Uma)
Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205160848.24662-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Pass the crtc state etc. as const to the color management commit
functions. And while at it polish some of the local variables.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205160848.24662-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
First of all GMCH can be considered a feature by itself
since it is a chip present in some platforms that connects
the IA processor to memory and other components in PC.
Also with the introduction of display block at device info,
we got a redundant definition:
.display.has_gmch_display = 1,
So, let's clean up things a bit and use the standardized
way of has_feature on displays side.
No functional change and no manual interaction to generate
this patch.
It is only:
sed -si -e 's/has_gmch_display/has_gmch/g' \
-e 's/HAS_GMCH_DISPLAY/HAS_GMCH/g' drivers/gpu/drm/i915/*{c,h}
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190204222538.15842-1-rodrigo.vivi@intel.com
We want to expose the ability to reconfigure the slices, subslice and
eu per context and per engine. To facilitate that, store the current
configuration on the context for each engine, which is initially set
to the device default upon creation.
v2: record sseu configuration per context & engine (Chris)
v3: introduce the i915_gem_context_sseu to store powergating
programming, sseu_dev_info has grown quite a bit (Lionel)
v4: rename i915_gem_sseu into intel_sseu (Chris)
use to_intel_context() (Chris)
v5: More to_intel_context() (Tvrtko)
Switch intel_sseu from union to struct (Tvrtko)
Move context default sseu in existing loop (Chris)
v6: s/intel_sseu_from_device_sseu/intel_device_default_sseu/ (Tvrtko)
Tvrtko Ursulin:
v7:
* Pass intel_sseu by pointer instead of value to make_rpcs.
* Rebase for make_rpcs changes.
v8:
* Rebase for RPCS edit on pin.
v9:
* Rebase for context image setup changes.
v10:
* Rename dev_priv to i915. (Chris Wilson)
v11:
* Rebase.
v12:
* Rebase for IS_GEN changes.
v13:
* Rebase for RUNTIME_INFO.
v14:
* Rebase for intel_context_init.
v15:
* Rebase for drm-tip changes.
v16:
* Moved struct intel_sseu definition to i915_gem_context.h.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205095032.22673-1-tvrtko.ursulin@linux.intel.com
On icl+ bspec tells us to calculate a separate minimum ddb
allocation from the blocks watermark. Both have to be checked
against the actual ddb allocation, but since we do things the
other way around we'll just calculat the minimum acceptable
ddb allocation by taking the maximum of the two values.
We'll also replace the memcmp() with a full trawl over the
the watermarks so that it'll ignore the min_ddb_alloc
because we can't directly read that out from the hw. I suppose
we could reconstruct it from the other values, but I was
too lazy to do that now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181221171436.8218-6-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Now that we pin timelines around use, we have a clearly defined lifetime
and convenient points at which we can track only the active timelines.
This allows us to reduce the list iteration to only consider those
active timelines and not all.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128181812.22804-6-chris@chris-wilson.co.uk
If we restrict ourselves to only using a cacheline for each timeline's
HWSP (we could go smaller, but want to avoid needless polluting
cachelines on different engines between different contexts), then we can
suballocate a single 4k page into 64 different timeline HWSP. By
treating each fresh allocation as a slab of 64 entries, we can keep it
around for the next 64 allocation attempts until we need to refresh the
slab cache.
John Harrison noted the issue of fragmentation leading to the same worst
case performance of one page per timeline as before, which can be
mitigated by adopting a freelist.
v2: Keep all partially allocated HWSP on a freelist
This is still without migration, so it is possible for the system to end
up with each timeline in its own page, but we ensure that no new
allocation would needless allocate a fresh page!
v3: Throw a selftest at the allocator to try and catch invalid cacheline
reuse.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128181812.22804-4-chris@chris-wilson.co.uk
Currently, the list of timelines is serialised by the struct_mutex, but
to alleviate difficulties with using that mutex in future, move the
list management under its own dedicated mutex.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128102356.15037-5-chris@chris-wilson.co.uk
Now that the submission backends are controlled via their own spinlocks,
with a wave of a magic wand we can lift the struct_mutex requirement
around GPU reset. That is we allow the submission frontend (userspace)
to keep on submitting while we process the GPU reset as we can suspend
the backend independently.
The major change is around the backoff/handoff strategy for performing
the reset. With no mutex deadlock, we no longer have to coordinate with
any waiter, and just perform the reset immediately.
Testcase: igt/gem_mmap_gtt/hang # regresses
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125132230.22221-3-chris@chris-wilson.co.uk
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-7-jani.nikula@intel.com
Since commit 93065ac753 ("mm, oom: distinguish blockable mode for mmu
notifiers") we have been able to report failure from
mmu_invalidate_range_start which allows us to use a trylock on the
struct_mutex to avoid potential recursion and report -EBUSY instead.
Furthermore, this allows us to pull the work into the main callback and
avoid the sleight-of-hand in using a workqueue to avoid lockdep.
However, not all paths to mmu_invalidate_range_start are prepared to
handle failure, so instead of reporting the recursion, deal with it by
propagating the failure upwards, who can decide themselves to handle it
or report it.
v2: Mark up the recursive lock behaviour and comment on the various weak
points.
v3: Follow commit 3824e41975 ("drm/i915: Use mutex_lock_killable() from
inside the shrinker") and also use mutex_lock_killable().
v3.1: No leak on EINTR.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108375
References: 93065ac753 ("mm, oom: distinguish blockable mode for mmu notifiers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190115124442.3500-1-chris@chris-wilson.co.uk
As the GT_IRQ power domain implies a wakeref, we can use it inplace of
our existing redundant rpm grab.
v2: Drop papering over forgetting to take the runtime wakeref in
selftests
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-20-chris@chris-wilson.co.uk
On module load and unload, we grab the POWER_DOMAIN_INIT powerwells and
transfer them to the runtime-pm code. We can use our wakeref tracking to
verify that the wakeref is indeed passed from init to enable, and
disable to fini; and across suspend.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-17-chris@chris-wilson.co.uk
The majority of runtime-pm operations are bounded and scoped within a
function; these are easy to verify that the wakeref are handled
correctly. We can employ the compiler to help us, and reduce the number
of wakerefs tracked when debugging, by passing around cookies provided
by the various rpm_get functions to their rpm_put counterpart. This
makes the pairing explicit, and given the required wakeref cookie the
compiler can verify that we pass an initialised value to the rpm_put
(quite handy for double checking error paths).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-16-chris@chris-wilson.co.uk
Record the wakeref used for keeping the device awake as the GPU is
executing requests and be sure to cancel the tracking upon parking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-3-chris@chris-wilson.co.uk
The majority of runtime-pm operations are bounded and scoped within a
function; these are easy to verify that the wakeref are handled
correctly. We can employ the compiler to help us, and reduce the number
of wakerefs tracked when debugging, by passing around cookies provided
by the various rpm_get functions to their rpm_put counterpart. This
makes the pairing explicit, and given the required wakeref cookie the
compiler can verify that we pass an initialised value to the rpm_put
(quite handy for double checking error paths).
For regular builds, the compiler should be able to eliminate the unused
local variables and the program growth should be minimal. Fwiw, it came
out as a net improvement as gcc was able to refactor rpm_get and
rpm_get_if_in_use together,
v2: Just s/rpm_put/rpm_put_unchecked/ everywhere, leaving the manual
mark up for smaller more targeted patches.
v3: Mention the cookie in Returns
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-2-chris@chris-wilson.co.uk
Everytime we take a wakeref, record the stack trace of where it was
taken; clearing the set if we ever drop back to no owners. For debugging
a rpm leak, we can look at all the current wakerefs and check if they
have a matching rpm_put.
v2: Use skip=0 for unwinding the stack as it appears our noinline
function doesn't appear on the stack (nor does save_stack_trace itself!)
v3: Allow rpm->debug_count to disappear between inspections and so
avoid calling krealloc(0) as that may return a ZERO_PTR not NULL! (Mika)
v4: Show who last acquire/released the runtime pm
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-1-chris@chris-wilson.co.uk
Needs just a few additional includes here and there.
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108082709.3748-1-jani.nikula@intel.com
Ignore trying to shrink from i915 if we fail to acquire the struct_mutex
in the shrinker while performing direct-reclaim. The trade-off being
(much) lower latency for non-i915 clients at an increased risk of being
unable to obtain a page from direct-reclaim without hitting the
oom-notifier. The proviso being that we still keep trying to hard
obtain the lock for kswapd so that we can reap under heavy memory
pressure.
v2: Taint all mutexes taken within the shrinker with the struct_mutex
subclass as an early warning system, and drop I915_SHRINK_ACTIVE from
vmap to reduce the number of dangerous paths. We also have to drop
I915_SHRINK_ACTIVE from oom-notifier to be able to make the same claim
that ACTIVE is only used from outside context, which fits in with a
longer strategy of avoiding stalls due to scanning active during
shrinking.
The danger in using the subclass struct_mutex is that we declare
ourselves more knowledgable than lockdep and deprive ourselves of
automatic coverage. Instead, we require ourselves to mark up any mutex
taken inside the shrinker in order to detect lock-inversion, and if we
miss any we are doomed to a deadlock at the worst possible moment.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107115509.12523-1-chris@chris-wilson.co.uk
Now that we have eliminated the CPU-side irq_seqno_barrier by moving the
delays on the GPU before emitting the MI_USER_INTERRUPT, we can remove
the engine->irq_seqno_barrier infrastructure. Though intentionally
slowing down the GPU is nasty, so is the code we can now remove!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228171641.16531-6-chris@chris-wilson.co.uk
The writing is on the wall for the existence of a single execution queue
along each engine, and as a consequence we will not be able to track
dependencies along the HW queue itself, i.e. we will not be able to use
HW semaphores on gen7 as they use a global set of registers (and unlike
gen8+ we can not effectively target memory to keep per-context seqno and
dependencies).
On the positive side, when we implement request reordering for gen7 we
also can not presume a simple execution queue and would also require
removing the current semaphore generation code. So this bring us another
step closer to request reordering for ringbuffer submission!
The negative side is that using interrupts to drive inter-engine
synchronisation is much slower (4us -> 15us to do a nop on each of the 3
engines on ivb). This is much better than it was at the time of introducing
the HW semaphores and equally important userspace weaned itself off
intermixing dependent BLT/RENDER operations (the prime culprit was glyph
rendering in UXA). So while we regress the microbenchmarks, it should not
impact the user.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108888
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228140736.32606-2-chris@chris-wilson.co.uk
After we found a workaround for a hang on context load, Ben Widawsky
found confirmation that it was for an issue with waking from rc6 and
loading a context image.
The workaround from on high suggests that we should
I915_WRITE(RING_WAIT_FOR_RC6_EXIT(engine->mmio_base),
_MASKED_FIELD(RING_RC6_SEL_WRITE_ADDR_MASK,
RING_RC6_SEL_WRITE_ADDR_UPPER_LEFT));
in our rc6 setup for Haswell GT1, but on applying that we find instead
that the machine encounters a GT forcewake error and locks up.
As we are removing HW semaphore usage in the next patch, and the
suggested workaround is no improvement, we need to
decouple the PSMI workaround from HAS_SEMAPHORES to IS_HSW_GT1.
References: 2c55018347 ("drm/i915: Disable PSMI sleep messages on all rings around context switches")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228140736.32606-1-chris@chris-wilson.co.uk
This is needed by the next patch to determine if a DDI TypeC port is
physically wired to a legacy DP or legacy HDMI connector or if the port
is wired to a USB-C/Thunderbolt connector.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-3-imre.deak@intel.com
Define IS_GEN() similarly to our IS_GEN_RANGE(). but use gen instead of
gen_mask to do the comparison. Now callers can pass then gen as a parameter,
so we don't require one macro for each gen.
The following spatch was used to convert the users of these macros:
@@
expression e;
@@
(
- IS_GEN2(e)
+ IS_GEN(e, 2)
|
- IS_GEN3(e)
+ IS_GEN(e, 3)
|
- IS_GEN4(e)
+ IS_GEN(e, 4)
|
- IS_GEN5(e)
+ IS_GEN(e, 5)
|
- IS_GEN6(e)
+ IS_GEN(e, 6)
|
- IS_GEN7(e)
+ IS_GEN(e, 7)
|
- IS_GEN8(e)
+ IS_GEN(e, 8)
|
- IS_GEN9(e)
+ IS_GEN(e, 9)
|
- IS_GEN10(e)
+ IS_GEN(e, 10)
|
- IS_GEN11(e)
+ IS_GEN(e, 11)
)
v2: use IS_GEN rather than GT_GEN and compare to info.gen rather than
using the bitmask
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-2-lucas.demarchi@intel.com
RANGE makes it longer, but clearer. We are also going to add a macro to
check an individual gen, so add the _RANGE prefix here.
Diff generated with:
sed 's/IS_GEN(/IS_GEN_RANGE(/g' drivers/gpu/drm/i915/{*/,}*.{c,h} -i
v2: use IS_GEN rather than GT_GEN
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-1-lucas.demarchi@intel.com
Try to be more consistent about intel_* types rather than drm_* types
for lower-level driver functions. While we're at it, let's also be more
consistent with state variable naming (half of the platforms use the
name 'state' whereas the other half used 'crtc_state').
While we're touching these variables, let's also be more consistent
about always naming the intel_crtc_state's "crtc_state" rather than
"state" so that different platform types aren't using different naming
conventions.
v2:
- s/state/crtc_state/ for consistency between platform types (Ville)
- Drop the crtc parameter to intel_color_check(); we can just pull that
out of the state object.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210215415.19854-2-matthew.d.roper@intel.com
Try to be more consistent about intel_* types rather than drm_* types
for lower-level driver functions.
v2:
- Also drop the intel_crtc parameter from compute_intermediate_wm()
since we can just extract it from the crtc_state parameter. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210215415.19854-1-matthew.d.roper@intel.com
According to eDP spec, sink can required specific selective update
granularity that source must comply.
Here caching the value if required and checking if source supports
it.
v3:
- Returning the default granularity in case DPCD read fails(Dhinakaran)
- Changed DPCD error message level(Dhinakaran)
v4:
- Setting granularity to defaul when granularity read is equal to
0(Dhinakaran)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-9-jose.souza@intel.com
Currently we allocate a scratch page for each engine, but since we only
ever write into it for post-sync operations, it is not exposed to
userspace nor do we care for coherency. As we then do not care about its
contents, we can use one page for all, reducing our allocations and
avoid complications by not assuming per-engine isolation.
For later use, it simplifies engine initialisation (by removing the
allocation that required struct_mutex!) and means that we can always rely
on there being a scratch page.
v2: Check that we allocated a large enough scratch for I830 w/a
Fixes: 06e562e7f5 ("drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5") # v4.18.20
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108850
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.18.20+
Convert the per context workaround handling code to run against the newly
introduced common workaround framework and fuse the two to use the
existing smarter list add helper, the one which does the sorted insert and
merges registers where possible.
This completes migration of all four classes of workarounds onto the
common framework.
Existing macros are kept untouched for smaller code churn.
v2:
* Rename to list name ctx_wa_list and move from dev_priv to engine.
v3:
* API rename and parameters tweaking. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133357.10341-1-tvrtko.ursulin@linux.intel.com
To enable later verification of GT workaround state at various stages of
driver lifetime, we record the list of applicable ones per platforms to a
list, from which they are also applied.
The added data structure is a simple array of register, mask and value
items, which is allocated on demand as workarounds are added to the list.
This is a temporary implementation which later in the series gets fused
with the existing per context workaround list handling. It is separated at
this stage since the following patch fixes a bug which needs to be as easy
to backport as possible.
Also, since in the following patch we will be adding a new class of
workarounds (per engine) which can be applied from interrupt context, we
straight away make the provision for safe read-modify-write cycle.
v2:
* Change dev_priv to i915 along the init path. (Chris Wilson)
* API rename. (Chris Wilson)
v3:
* Remove explicit list size tracking in favour of growing the allocation
in power of two chunks. (Chris Wilson)
v4:
Chris Wilson:
* Change wa_list_finish to early return.
* Copy workarounds using the compiler for static checking.
* Do not bother zeroing unused entries.
* Re-order struct i915_wa_list.
v5:
* kmalloc_array.
* Whitespace cleanup.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133319.10174-1-tvrtko.ursulin@linux.intel.com
This helps separate what capabilities are display capabilities.
v3: Moving display struct right after flags (Lucas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-2-jose.souza@intel.com
Right now it is decided if GEN has display by checking the num_pipes,
so lets make it explicit and use a macro.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-1-jose.souza@intel.com
As stated in struct drm_encoder, crtc field should only be used
by non-atomic drivers.
So here caching the pipe id in intel_psr_enable() what is way more
simple and efficient than at every call to
intel_psr_flush()/invalidate() get the
drm.mode_config.connection_mutex lock to safely be able to get the
pipe id by reading drm_connector_state.crtc.
This should fix the null pointer dereference crash below as the
previous way to get the pipe id was prone to race conditions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105959
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128072838.22773-1-jose.souza@intel.com
1. Disable Left/right VDSC branch in DSS Ctrl reg
depending on the number of VDSC engines being used
2. Disable joiner in DSS Ctrl reg
v4:
* Remove encoder, make crtc_state const (Ville)
v3 (From Manasi):
* Add Disable PG2 for VDSC on eDP
v2 (From Manasi):
* Use old_crtc_state to find dsc params
* Add a condition to disable only if
dsc state compression is enabled
* Use correct DSS CTL regs
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-12-manasi.d.navare@intel.com
After encoder->pre_enable() hook, after link training sequence is
completed, PPS registers for DSC encoder are configured using the
DSC state parameters in intel_crtc_state as part of DSC enabling
routine in the source. DSC enabling routine is called after
encoder->pre_enable() before enbaling the pipe and after
compression is enabled on the sink.
v7:
* Remove unnecessary comments, leftovers (Ville)
* No need for explicit val &= ~ (Ville)
v6:
intel_dsc_enable to be part of pre_enable hook (Ville)
v5:
* make crtc_state const (Ville)
v4:
* Use cpu_transcoder instead of encoder->type for using EDP transcoder
DSC registers(Ville)
* Keep all PSS regs together (Anusha)
v3:
* Configure Pic_width/2 for each VDSC engine when two VDSC engines per pipe
are used (Manasi)
* Add DSC slice_row_per_frame in PPS16 (Manasi)
v2:
* Enable PG2 power well for VDSC on eDP
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[manasi: fixup the line longer than 100 chars while applying]
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-8-manasi.d.navare@intel.com
Basic DSC parameters and DSC configuration data needs to be computed
for each of the requested mode during atomic check. This is
required since for certain modes, valid DSC parameters and config
data might not be computed in which case compression cannot be
enabled for that mode.
For that reason we need to add these params and config structure
to the intel_crtc_state so that if valid this state information
can directly be used while enabling DSC in atomic commit.
v2:
* Rebase on drm-tip (Manasi)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-1-manasi.d.navare@intel.com
On SKL+ the plane WM/BUF_CFG registers are a proper part of each
plane's register set. That means accessing them will cancel any
pending plane update, and we would need a PLANE_SURF register write
to arm the wm/ddb change as well.
To avoid all the problems with that let's just move the wm/ddb
programming into the plane update/disable hooks. Now all plane
registers get written in one (hopefully atomic) operation.
To make that feasible we'll move the plane ddb tracking into
the crtc state. Watermarks were already tracked there.
v2: Rebase due to input CSC
v3: Split out a bunch of junk (Matt)
v4: Add skl_wm_add_affected_planes() to deal with
cursor special case and non-zero wm register reset value
v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt)
Remove the redundant ddb memset() (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165900.31298-1-ville.syrjala@linux.intel.com
While PSR is active hardware will do aux transactions by it self to
wakeup sink to receive a new frame when necessary. If that
transaction is not acked by sink, hardware will trigger this
interruption.
So let's disable PSR as it is a hint that there is problem with this
sink.
The removed FIXME was asking to manually train the link but we don't
need to do that as by spec sink should do a short pulse when it is
out of sync with source, we just need to make sure it is awaken and
the SDP header with PSR inactive set it will trigger the short pulse
with a error set in the link status.
v3: added workarround to fix scheduled work starvation cause by
to frequent PSR error interruption
v4: only setting irq_aux_error as we don't care in clear it and
not using dev_priv->irq_lock as consequence.
v5: rebased: using edp_psr_shift()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-4-jose.souza@intel.com
When we detect a error and disable PSR, it is kept disabled until the
next modeset but as the sink already show signs that it do not
properly work with PSR lets disabled it for good to avoid any
additional flickering.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-3-jose.souza@intel.com
VBT appears to have two (or possibly three) ways to indicate the panel
rotation. The first is in the MIPI config block, but that apparenly
usually (maybe always?) indicates 0 degrees despite the actual panel
orientation. The second way to indicate this is in the general features
block, which can just indicate whether 180 degress rotation is used.
The third might be a separate rotation data block, but that is not
at all documented so who knows what it may contain.
Let's try the first two. We first try the DSI specicic VBT
information, and it it doesn't look trustworthy (ie. indicates
0 degrees) we fall back to the 180 degree thing. Just to avoid too
many changes in one go we shall also keep the hardware readout path
for now.
If this works for more than just my VLV FFRD the question becomes
how many of the panel orientation quirks are now redundant?
v2: Move the code into intel_dsi.c (Jani)
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022142015.4026-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
This reduces the size of struct skl_wm_level from 6 to 4, which
reduces the size of struct skl_plane_wm from 104 to 70, which reduces
the size of struct skl_pipe_wm from 524 to 356. A reduction of 168
padding bytes per pipe. This will increase even more the next time we
bump I915_MAX_PLANES.
v2: Paste the pahole output provided by Lucas:
$ pahole -s -C skl_wm_level drivers/gpu/drm/i915/i915.o
struct skl_wm_level {
bool plane_en; /* 0 1 */
/* XXX 1 byte hole, try to pack */
uint16_t plane_res_b; /* 2 2 */
uint8_t plane_res_l; /* 4 1 */
/* size: 6, cachelines: 1, members: 3 */
/* sum members: 4, holes: 1, sum holes: 1 */
/* padding: 1 */
/* last cacheline: 6 bytes */
};
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016220133.26991-3-paulo.r.zanoni@intel.com
Similarly to the GEN9_LP DPIO PHY code keep the CNL+ combo PHY code in a
separate file.
No functional change.
v2:
- Use SPDX license tag instead of boilerplate. (Rodrigo)
v3:
- Use MIT instead of GPL-2.0 license. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106160621.23057-3-imre.deak@intel.com
Unfortunately, it seems that the HPD IRQ storm problem from the early
days of Intel GPUs was never entirely solved, only mostly. Within the
last couple of days, I got a bug report from one of our customers who
had been having issues with their machine suddenly booting up very
slowly after having updated. The amount of time it took to boot went
from around 30 seconds, to over 6 minutes consistently.
After some investigation, I discovered that i915 was reporting massive
amounts of short HPD IRQ spam on this system from the DisplayPort port,
despite there not being anything actually connected. The symptoms would
start with one "long" HPD IRQ being detected at boot:
[ 1.891398] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00440000, dig 0x00440000, pins 0x000000a0
[ 1.891436] [drm:intel_hpd_irq_handler [i915]] digital hpd port B - long
[ 1.891472] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 5 - cnt: 0
[ 1.891508] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - long
[ 1.891544] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 7 - cnt: 0
[ 1.891592] [drm:intel_dp_hpd_pulse [i915]] got hpd irq on port B - long
[ 1.891628] [drm:intel_dp_hpd_pulse [i915]] got hpd irq on port D - long
…
followed by constant short IRQs afterwards:
[ 1.895091] [drm:intel_encoder_hotplug [i915]] [CONNECTOR:66:DP-1] status updated from unknown to disconnected
[ 1.895129] [drm:i915_hotplug_work_func [i915]] Connector DP-3 (pin 7) received hotplug event.
[ 1.895165] [drm:intel_dp_detect [i915]] [CONNECTOR:72:DP-3]
[ 1.895275] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.895312] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.895762] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.895799] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.896239] [drm:intel_dp_aux_xfer [i915]] dp_aux_ch timeout status 0x71450085
[ 1.896293] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.896330] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.896781] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.896817] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.897275] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
The customer's system in question has a GM45 GPU, which is apparently
well known for hotplugging storms.
So, workaround this impressively broken hardware by changing the default
HPD storm threshold from 5 to 50. Then, make long IRQs count for 10, and
short IRQs count for 1. This makes it so that 5 long IRQs will trigger
an HPD storm, and on systems with short HPD storm detection 50 short
IRQs will trigger an HPD storm. 50 short IRQs amounts to 100ms of
constant pulsing, which seems like a good middleground between being too
sensitive and not being sensitive enough (which would cause visible
stutters in userspace every time a storm occurs).
And just to be extra safe: we don't enable this by default on systems
with MST support. There's too high of a chance of MST support triggering
storm detection, and systems that are new enough to support MST are a
lot less likely to have issues with IRQ storms anyway.
As a note: this patch was tested using a ThinkPad T450s and a Chamelium
to simulate the short IRQ storms.
Changes since v1:
- Don't use two separate thresholds, just make long IRQs count for 10
each and short IRQs count for 1. This simplifies the code a bit
- Ville Syrjälä
Changes since v2:
- Document @long_hpd in intel_hpd_irq_storm_detect, no functional
changes
Changes since v4:
- Remove !! in long_hpd assignment - Ville Syrjälä
- queue_hp = true - Ville Syrjälä
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106213017.14563-6-lyude@redhat.com
Most of the AUX_CH_CTL flags are concerned with DP AUX transfer
parameters. As opposed to this the flag specifying the thunderbolt vs.
non-thunderbolt mode of the port is not related to AUX transfers at all
(rather it's repurposed to enable either TBT or non-TBT PHY HW blocks).
The programming has to be done before enabling the corresponding AUX
power well, so make it part of the power well code.
v3:
- Use existing enable/disable helpers instead of opencoding. (Jose)
- Fix type of is_tc_tbt to remain a bitfield. (Lucas)
- Add comment describing the is_tc_tbt power well flag. (Lucas)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108548
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-8-imre.deak@intel.com
From ICL onwards all the DDI/TypeC ports - even working in HDMI mode -
need to know their corresponding AUX channel, so move the corresponding
helper to a common place.
No functional change.
v4:
- Fix 'no space is necessary after a cast' checkpatch warn.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-2-imre.deak@intel.com
commit ac657f6461 ("drm/i915: Introduce IS_GEN macro") introduced
GEN_FOREVER that was never used.
My first attempt was to rename it to FOREVER since GEN is
already part of the macro. Then I used coccinelle to change all
-INTEL_GEN(e1) >= e2
+INTEL_GEN_RANGE(e1, e2, FOREVER)
-INTEL_GEN(e1) <= e2
+INTEL_GEN_RANGE(e1, 0, e2)
and I liked it.
However I didn't like very much the remaining
INTEL_GEN(dev_priv) < n
and:
INTEL_GEN(e1) < n
INTEL_GEN_RANGE(e1, 0, n - 1)
didn't make much sense either.
So INTEL_GEN use for > or < seems a better unified way for unlimited
bounds. So, no reason to keep GEN_FOREVER here.
Let's kill before someone start using it.
v2: Remove remaining GEN_FOREVER forgotten in a comment. (Daniel)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195143.20353-2-rodrigo.vivi@intel.com
The 16Gb DIMM w/a is not applicable to BXT or GLK. Limit it to
the appropriate platforms.
This was especially harsh on GLK since we don't even try to read
the DIMM information on that platforms, hence valid_dimm was
always false and thus we always tried to apply the w/a.
Furthermore the w/a pushed the level 0 latency above the
level 1 latency, which doesn't really make sense.
v2: Do the check when populating is_16gb_dimm (Mahesh)
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 86b592876c ("drm/i915: Implement 16GB dimm wa for latency level-0")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023182102.31549-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.sh.kumar@gmail.com>
The way our hardware is designed doesn't seem to let us use the
MI_RECORD_PERF_COUNT command without setting up a circular buffer.
In the case where the user didn't request OA reports to be available
through the i915 perf stream, we can set the OA buffer to the minimum
size to avoid consuming memory which won't be used by the driver.
v2: Simplify oa buffer size exponent selection (Chris)
Reuse vma size field (Lionel)
v3: Restrict size opening parameter to values supported by HW (Chris)
v4: Drop out of date comment (Matt)
Add debug message when buffer size is rejected (Matt)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023100707.31738-5-lionel.g.landwerlin@intel.com
We initialize the OA buffer everytime we enable the OA unit (first call in
gen[78]_oa_enable), so we don't need to initialize when preparing the metric
set.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023100707.31738-3-lionel.g.landwerlin@intel.com
Now that we have intel_connector.c, move the connector specific
functions from intel_display.c there. Fix a few checkpatch complaints
while at it. No functional changes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181010075205.7713-2-jani.nikula@intel.com
ALPM is a requirement and we don't need to keep it's cached, what
were done in commit 97c9de66ca
("drm/i915/psr: Fix ALPM cap check for PSR2") but the alpm was not
removed from i915_psr.
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003205031.32474-7-jose.souza@intel.com
According to patch "drm/i915/aml: Introducing Amber Lake platform"
(e364672477). Add a new marco for AML ULX GT2 devices.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538034499-31256-1-git-send-email-shawn.c.lee@intel.com
Add plane alpha blending support with the different blend modes.
This has been tested on a icl to show the correct results,
on earlier platforms small rounding errors cause issues. But this
already happens case with fully transparant or fully opaque RGB8888
fb's.
The recommended HW workaround is to disable alpha blending when the
plane alpha is 0 (transparant, hide plane) or 0xff (opaque, disable blending).
This is easy to implement on any platform, so just do that.
The tests for userspace are also available, and pass on gen11.
Changes since v1:
- Change mistaken < 0xff0 to 0xff00.
- Only set PLANE_KEYMSK_ALPHA_ENABLE when plane alpha < 0xff00, ignore blend mode.
- Rework disabling FBC when per pixel alpha is used.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Change MISSING_CASE default to explicit alpha disable (mattrope)]
Link: https://patchwork.freedesktop.org/patch/msgid/20180815103405.22679-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
In the next few patches, we will want to give a small priority boost to
some requests/queues but not so much that we perturb the user controlled
order. As such we will shift the user priority bits higher leaving
ourselves a few low priority bits for our internal bumping.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123204.23982-3-chris@chris-wilson.co.uk
Now that we are confident in providing full-ppgtt where supported,
remove the ability to override the context isolation.
v2: Remove faked aliasing-ppgtt for testing as it no longer is accepted.
v3: s/USES/HAS/ to match usage and reject attempts to load the module on
old GVT-g setups that do not provide support for full-ppgtt.
v4: Insulate ABI ppGTT values from our internal enum (later plans
involve moving ppGTT depth out of the enum, thus potentially breaking
ABI unless we document the current values).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Zhi Wang <zhi.a.wang@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926201222.5643-1-chris@chris-wilson.co.uk
Partial views are small but there can be many of them, and since the sg
list space for them is allocated pessimistically, we can save some slab by
trimming the unused tail entries.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926080353.20867-1-tvrtko.ursulin@linux.intel.com
Move max firmware size to the same if ladder with firmware name and
required version. This allows us to detect the missing max size for a
platform without actually loading the firmware, and makes the whole
thing easier to maintain.
We need to move the power get earlier to allow for early return in the
missing platform case. While at it, extend the comment on why we return
with the reference held on errors.
We also need to move the module parameter override later to reuse the
max firmware size, which is independent of the override.
v2: Add comment on why we leak the wakeref on errors (Chris)
v3: Rebase
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926133414.22073-2-jani.nikula@intel.com
It really wants dev_priv anyway, also now matches i915_gem_init_stolen.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920142707.19659-2-matthew.auld@intel.com
Chris Wilson