Enable both MMC controllers present on Asurada. MMC0 is for
non-removable internal memory, while MMC1 is an SD card slot. MMC1 isn't
used on all machines, but in those cases the CD interrupt is never
triggered and thus it is basically as if it was disabled.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-18-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Asurada platform uses regulators from MT6315 PMICs acessible through
SPMI. Add support for them.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-17-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6359 is the primary PMIC present on the Asurada platform. Include its
dtsi and configure properties specific for the platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-16-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable MT8192's PCIe controller and add support for the MT7921e WiFi
card that is present on that bus for the Asurada platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-15-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable XHCI controller on the Asurada platform. This allows the use of
the USB ports, and therefore a rootfs can be loaded and a usable shell
reached from a live USB image.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-14-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Spherion board has keyboard backlight controlled by the PWM signal
generated by the ChromeOS EC.
Enable PWM output for ChromeOS EC and add a PWM controlled LED node for
the keyboard backlight.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-13-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
All machines of the Asurada platform have a touchscreen at address 0x10
in the I2C0 bus, but the devices vary: Spherion has the Elan eKTH3500
touchscreen, while Hayato has a generic HID-over-i2c touchscreen.
Add common support for the touchscreens on the platform and the
specifics in each board file.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-12-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the Elan eKTH3000 i2c trackpad present on Asurada. It is
connected to the I2C2 bus and has address 0x15.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-11-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Asurada platform has a Google Security Chip connected to the SPI5
bus. It runs the cr50 firmware and provides TPM functionality. Add
support for it.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-10-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Chromebooks' embedded keyboards differ from standard layouts for the
top row in that they have shortcuts in place of the standard function
keys. Map these keys to achieve the functionality that is pictured on
the printouts.
There's a minor difference between the keys present on Hayato, which
uses an older layout, and Spherion, which uses a newer one.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-9-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the ChromeOS Embedded Controller present on the Asurada
platform. It is connected through the SPI1 bus and offers several
functionalities: base detection, PWM controller, I2C tunneling,
regulators, Type-C connector management, keyboard and Smart Battery
Metrics (SBS).
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-8-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Asurada platform has five I2C controllers and two SPI controllers
that are used. In preparation for enabling the devices connected to
these controllers, enable and configure their busses.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-7-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add system-wide power supplies present on all of the boards in the
Asurada family.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-6-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the gpio-line-names property to gpio-controller in order to
document the usage of GPIOs on the Asurada platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-5-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Introduce the MT8192 Asurada Chromebook platform, including the Asurada
Spherion and Asurada Hayato boards.
This is enough configuration to get serial output working on Spherion
and Hayato.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-4-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add binding for the Google Hayato board.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-3-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add binding for the Google Spherion board, which is used for Acer
Chromebook 514 (CB514-2H).
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a phandle to the MT8183_POWER_DOMAIN_MFG_ASYNC power domain and
assign the GPU VSRAM supply to this in mt8183-kukui: this allows to
keep the sram powered up while the GPU is used.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220623123850.110225-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This commit adds dt-binding documentation for the MediaTek MT8186
reference board.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220520122217.30716-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a node for the pinctrl controller found on MT6795 but without
configuration for any pin, as that's expected to be done in the
machine-specific devicetrees.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-10-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Remove the RTC and UART fixed clocks, as these were introduced to
temporarily provide a dummy clock to devices: since the two 26M/32K
fixed oscillators clocks (which do really exist in the SoC) have
been added, there's no reason to keep the aforementioned (and now
redundant) dummies in this devicetree.
In order to remove the uart dummy clock, it was necessary to also
reassign the clock of all UART nodes to clk26m.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the 32kHz and 26MHz oscillators as fixed clocks in devicetree to
provide a good initial clock spec, since this SoC features two always
on oscillators running at the aforementioned frequencies.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
At least on commercial devices like some smartphones, the bootloader
will initialize the SoC watchdog and set it to reboot the board when
it times out. The last pet that this watchdog is getting is right
before booting the kernel and left it enabled as a protection against
boot failure: this means that Linux is expected to initialize this
device and pet as soon as possible, or it will bark and reset the AP.
In order to prevent that, add the required watchdog node as default
enabled: this will have no side effects on boards that are not
performing the aforementioned watchdog setup before booting Linux.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC is HMP and has two clusters with four Cortex-A53 cores each:
declare a cpu map and, while at it, also add the next-level-cache
properties.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MMIO devices should be inside of a soc bus node, as it's done for the
vast majority of ARM64 devicetrees, and for almost all MTK devicetrees.
Create a simple-bus soc node and move all devices with a MMIO address
space in there.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The IOMMU driver now looks for the "mediatek,infracfg" phandle as a
new way to retrieve a syscon to that:
even though the old way is retained, it has been deprecated and the
driver will write a message in kmsg advertising to use the phandle
way instead.
For this reason, assign the right phandle to mediatek,infracfg in
the iommu node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220616110830.26037-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The IOMMU driver now looks for the "mediatek,infracfg" phandle as a
new way to retrieve a syscon to that:
even though the old way is retained, it has been deprecated and the
driver will write a message in kmsg advertising to use the phandle
way instead.
For this reason, assign the right phandle to mediatek,infracfg in
the iommu node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220616110830.26037-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Need also provide a specific compatible "mediatek,mt8192-efuse" at
the same time when use the generic compatible "mediatek,efuse".
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617093132.22578-3-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The entry-method property of the idle-states node should be "psci" as
described in the idle-states binding, since this is already the value of
enable-method in the CPU nodes. Fix it to get rid of a dtbs_check
warning.
Fixes: 9260918d3a ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-3-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tweak the name of the idle-states subnodes so that they follow the
binding pattern, getting rid of dtbs_check warnings.
Only the usage of "-" in the name was necessary, but "off" was also
exchanged for "sleep" since that seems to be a more common wording in
other dts files.
Fixes: 9260918d3a ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As explained in Documentation/devicetree/bindings/mmc/mmc-controller.yaml,
the 'enable-sdio-wakeup' property is considered deprecated.
Replace it with the 'wakeup-source' property instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220621124435.121740-1-festevam@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We will use mediatek clock reset as infracfg_ao reset instead of
ti-syscon. To support this, remove property of ti reset and add
property of #reset-cells for mediatek clock reset.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220503093856.22250-17-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To support reset of infra, we add property of #reset-cells.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220503093856.22250-16-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to allow modules with latency requirements such as MDP3
to set registers through CMDQ, add the relevant dts property.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://lore.kernel.org/r/20220610063424.7800-6-moudy.ho@mediatek.com
[mb: fix commit subject]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The node names should be generic and DT schema expects certain pattern
with 'led'. Use generic color properties instead of the node name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-16-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220526204402.832393-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable USB remote wakeup of all four xHCI controller
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617072344.21461-2-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add efuse node and cells used by t-phy to fix the bit shift issue
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617072344.21461-1-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add compatible/reg/irq/clock/efuse setting in svs node.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220516004311.18358-3-roger.lu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add mediatek,cci property to support MediaTek CCI feature.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220516111130.13325-4-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Add cpufreq opp table.
- Add MediaTek cci opp table.
- Add property of opp table and clock fro cpufreq.
Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220516111130.13325-2-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
