The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Explicitly mark I2C GPIOs as open drain to fix the following
kernel message being printed:
enforced open drain please flag it properly in DT/ACPI DSDT/board file
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix. While
touching the hogs, fix indentation (spaces -> tabs).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds missing interrupt support for the internal Marvell
switch, so that the kernel does not have to keep polling the
PHYs on the bit-banged MDIO bus all the time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leave b{4,6}50v3 GPIO expander pca953x pins P05,P10,P11 unconfigured as
they are now used to implement an additional watchdog mechanism in user
space. P10,P11 pins remain unused (and therefore hogged) on b850v3.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For soc level of clocks which are input to Clock Control Module, clock
driver expects them to be under 'clocks' container node. But for board
level clocks, this container is not really necessary. Let's drop it and
use an unique name for fixed rate clock, so that 'reg' property can be
saved as well.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Remove unnecessary #address-cells/#size-cells from the switch nodes
to fix the following DTC warnings:
arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Default boot medium must be internal eMMC, we don't want the SDIO to be
used for these devices. This commit disables the SD card interface for
GE Healthcare Bx50v3 devices.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This commit enables i2c recovery, supported by the i2c core subsystem.
It defines the required GPIOs for SDA and SCL lines.
Signed-off-by: Jose Alarcon <jose.alarcon@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change the maxium spi clock frequency from 20MHz to 10MHz to meet the
operation voltage range requirement recommended in AT25 datasheet.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leave pca953x P06,P07 pins on b850v3 platform and P06 pin on
b450v3/b650v3 unconfigured in the kernel space since they could be
configured as DP1_RST and DP2_RST by the applications for the DP FW
update support.
Signed-off-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The license text has been mangled at some point then copy pasted across
multiple files. Restore it to what it should be.
Note that this is not intended as a license change.
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit b36581df7e ("spi: imx: Using existing properties for
chipselects") the device tree property 'fsl,spi-num-chipselects' is
unused and it is already marked as obsolete in device tree binding
documentation. Remove the property from the existing DTS files to
avoid its reoccurence on copying.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
At power on, pca953x GPIO pins are configured as input and may cause
unexpected interrupts. Configure the unused pins as GPO low to
avoid unexpected interrupts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
bx50v3 boards can be powered off via GPIO, this patch specifies the GPIO to
be used with the gpio-poweroff driver.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use
the Advantech BA-16 module (based on iMX6D). This file has the
devicetree entries that are common to all 3 boards.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski