Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"fsl,imx-ckih1" is useless since no driver deals with it, so let's drop it.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"fsl,imx-ckil" is useless since no driver deals with it, so let's drop it.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"fsl,imx-osc" is useless since no driver deals with it, so let's drop it.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the updated dt-bindings for the spba-bus, rename spba@xxxx
to spba-bus@xxxx. There are no functional changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- ranges property should be grouped by region, with no functional
changes. Otherwise, schema dtbs_check would report the following errors.
"linux-imx/arch/arm/boot/dts/imx6qp-vicutp.dt.yaml: pcie@1ffc000: ranges: 'oneOf' conditional failed, one must be fixed:
linux-imx/arch/arm/boot/dts/imx6qp-vicutp.dt.yaml: pcie@1ffc000: ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640]] is not of type 'boolean'
True was expected
[[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640]] is not of type 'null'
[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640] is too long
From schema: linux-imx/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml"
- refer to commit 281f1f99cf ("PCI: dwc: Detect number of iATU windows").
The num-viewport is not required anymore, remove them totally.
- dt_binding_check complains "compatible: ['fsl,imx6qp-pcie', 'snps,dw-pcie']
is too long", remove "snps,dw-pcie" from the compatible string.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two ways for SDMA accessing SPBA devices: one is SDMA->AIPS
->SPBA(masterA port), another is SDMA->SPBA(masterC port). Please refer
to the 'Figure 58-1. i.MX 6Dual/6Quad SPBA connectivity' of i.mx6DQ
Reference Manual. SDMA provide the corresponding app_2_mcu/mcu_2_app and
shp_2_mcu/mcu_2_shp script for such two options. So both AIPS and SPBA
scripts should keep the same behaviour, the issue only caught in AIPS
script sounds not solide.
The issue is more likely as the ecspi errata
ERR009165(http://www.nxp.com/docs/en/errata/IMX6DQCE.pdf):
eCSPI: TXFIFO empty flag glitch can cause the current FIFO transfer to
be sent twice
So revert commit 'dd4b487b32a3' firstly.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation for the conversion of the DWC HDMI TX device tree
bindings to YAML, move the HDMI encoder's 'port' nodes under a 'ports'
node. The 'ports' node is optional in the OF graph implementation, but
YAML bindings require it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX SoCs nand node name from "flexcan" to "can" to be compliant with
yaml schema, it requires the nodename to be "can". This fixes the following
error found by dtbs_check:
arch/arm/boot/dts/imx6dl-apf6dev.dt.yaml: flexcan@2090000: $nodename:0: 'flexcan@2090000' does not match '^can(@.*)?$'
From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add usb alias for bootloader searching the controller in correct order.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After this patch we need 2 arguments less for the fsl,stop-mode
property:
| commit d9b081e3fc
| Author: Marc Kleine-Budde <mkl@pengutronix.de>
| Date: Sun Jun 14 21:09:20 2020 +0200
|
| can: flexcan: remove ack_grp and ack_bit handling from driver
|
| Since commit:
|
| 048e3a34a2 can: flexcan: poll MCR_LPM_ACK instead of GPR ACK for stop mode acknowledgment
|
| the driver polls the IP core's internal bit MCR[LPM_ACK] as stop mode
| acknowledge and not the acknowledgment on chip level.
|
| This means the 4th and 5th value of the property "fsl,stop-mode" isn't used
| anymore. This patch removes the used "ack_gpr" and "ack_bit" from the driver.
This patch removes the two last arguments, as they are not needed
anymore.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Like the other i-MX devices the i.MX6 family can output the enet tx
clock on the pad to feed the connected device. Add the missing clk here
to avoid local fixups like: arch/arm/boot/dts/imx6qdl-tx6.dtsi.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX SoCs nand node name from "gpmi-nand" to "nand-controller" to
be compliant with yaml schema, it requires the nodename to be
"nand-controller".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.
This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtschema validator warnings like:
l2-cache@a02000: $nodename:0:
'l2-cache@a02000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX6/i.MX7 SoCs usdhc node name from usdhc to mmc to be
compliant with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In latest i.MX6Q RM Rev.6, 05/2020, #90 SPI interrupt is reserved,
so remove it from GPC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change OCOTP node name from ocotp-ctrl to efuse to be compliant with
yaml schema, it requires the nodename to be one of "eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6/7 SoCs' temperature sensor is inside anatop module from HW
perspective, so it should be a child node of anatop.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is the set of device tree changes, mostly covering new
hardware support, with 577 patches touching a little over 500
files.
There are five new Arm SoCs supported in this release, all of
them for existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in
both NAS devices and Android Set-top-box designs, along
with the "Horseradish", "Lion Skin" and "Mjolnir" reference
platforms; the Mele X1000 and Xnano X5 set-top-boxes and
the Banana Pi BPi-M4 single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC
and the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the
Odroid-GO Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2"
and YADRO OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform"
reference board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board
computer and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in existing
SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=17kt
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
- Update the imx6qdl gpr property to define gpr register
offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A series from Anson Huang updating SRC devices to match bindings
schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7IhYQUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5Bvwf8Cy/gm3ezs2OmjtdF3jql86qo7tqk
nUwPDnRhlPYInN8yKlipMsYn2yupCPSwENGYwxLculwsHyQ7RNEI8a1jY2zEkdh9
+IoZCNeOxOk40iQoCtaxBAJVz73BY8ptdKgfKL44xQ32e4oVQrgw1iAPdNS60yzl
5TRXxghYnfeRC5c7ZKKEF0X74RzWb/zwEWAcs3yczuPzQGAtcBmYTG8b/y+/HNT0
oTTcnN+clw48xAPuq6/8nMseVMLqTzyyBQpn/TI78LWGfBtaTIv6l7pjZBquhSGi
+QYKHgbC3POv8TYWGu+csqFfQvbfeiO/HEHFKPcvJ8O+QoRMB9nvejn42Q==
=I7h9
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree changes for 5.8:
- A series from Anson Huang updating SRC devices to match bindings
schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.
* tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (22 commits)
ARM: dts: imx53-cx9020: Group port definitions for the dvi-converter
ARM: dts: imx5: make src node name generic
ARM: dts: imx50: Add src node interrupt
ARM: dts: imx: make src node name generic
ARM: dts: imx7d-pinfunc: add input mux for ENET2 mdio
ARM: dts: imx6sl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl-gw5910: fix wlan regulator
ARM: dts: imx6qdl-gw5910: add support for bcm4330-bt
ARM: dts: imx6qdl-gw5904: add lsm9ds1 iio imu/magn support
ARM: dts: imx6qdl-gw560x: add lsm9ds1 iio imu/magn support
ARM: dts: imx53: Add src node interrupt
ARM: dts: imx51: Add src node interrupt
ARM: dts: imx50: Remove unused iomuxc-gpr node
ARM: dts: imx6qdl-gw552x: add USB OTG support
ARM: dts: imx6-sr-som: add ethernet PHY configuration
arm: dts: ls1021atwr: Add QSPI node properties
ARM: dts: e60k02: add interrupt for PMIC
ARM: dts: colibri: introduce device trees with UHS-I support
ARM: dts: imx7d: Add cpu1 supply
...
Link: https://lore.kernel.org/r/20200523032516.11016-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Node name should be generic, use "reset-controller" instead of "src" for
i.MX6/i.MX7 SoCs src nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although ocotp clock is always ON for i.MX6QDL, OCOTP can be
accessed directly, but since i.MX6QDL nvmem interface is supported,
and fsl,tempmon-data is deprecated, use it instead of getting fuse
data by reading ocotp directly, this makes all i.MX6 SoCs aligned.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is required for wake on lan on i.MX6
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to wake from suspend by ethernet magic packets the GPC
must be used as intc does not have wakeup functionality.
But the FEC DT node currently uses interrupt-extended,
specificying intc, thus breaking WoL.
This problem is probably fallout from the stacked domain conversion
as intc used to chain to GPC.
So replace "interrupts-extended" by "interrupts" to use the default
parent which is GPC.
Fixes: b923ff6af0 ("ARM: imx6: convert GPC to stacked domains")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nvmem related property for cpu0, then nvmem API could be used
to read cpu speed grading to avoid directly read OCOTP registers
mapped which could not handle defer probe.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto node should use the "crypto" generic naming,
and not a specific one ("sahara", "dcp", "caam").
Child nodes of the crypto node for caam crypto engine
should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX6/7 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "ocotp-ctrl" instead of "ocotp"
for all i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "watchdog" instead of "wdog" for
wdog nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "clock-controller" instead of
"ccm" for clks node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "keypad" instead of "kpp" for kpp node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "timer" instead of "gpt" for gpt node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per devicetree specification, generic names
are recommended to be used, such as bus.
i.MX AIPS is a AHB - IP bridge bus, so
we could use bus as node name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/vf*.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit fe2585e9c2 ("doc: dt: mtd: support partitions in a
special 'partitions' subnode") and commit 5cfdedb7b9 ("mtd: ofpart:
move ofpart partitions to a dedicated dt node") the partitioning should
be within a partitions sub-node.
Baseboard device trees following that scheme will get a dtc warning due
to the predefined #address-cells and #size-cells properties:
arch/arm/boot/dts/imx6qdl.dtsi:171.26-189.5: Warning (avoid_unnecessary_addr_size): /soc/gpmi-nand@112000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
I found no upstream imx6 baseboard using the old partitioning scheme, so
we can drop the two properties to avoid such warnings.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6Q/DL SabreSD board, vgen5 supplies vdd1p1/vdd2p5 LDO and
sw2 supplies vdd3p0 LDO, this patch assigns corresponding power
supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log:
vdd1p1: supplied by regulator-dummy
vdd3p0: supplied by regulator-dummy
vdd2p5: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p1: supplied by VGEN5
vdd3p0: supplied by SW2
vdd2p5: supplied by VGEN5
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since 25aaa75df1 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6 comes with 4 viewports, so configure PCIE node accordingly so
that the driver won't assume we only have 2.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add MMDC1 compatible string which is missing, and also set
it to be disabled by default, as most of the platforms ONLY
use single channel MMDC0, if dual MMDC channels are used, it
can be enabled in board dts file.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, so use "memory-controller"
instead of "mmdc" for MMDC node name, also remove "mmdc"
label for platforms with single MMDC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6q Technical reference manual shows the interrupt is
available to wake from sleep using the power button. The driver
has been available for quite some time, and other variants of the
i.MX6 have it enabled, so this implements it much like the others.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6qdl have duplicate memory nodes:
- One coming from the board device tree file: memory@
- One coming from the imx6qdl.dtsi file.
Fix the duplication by removing the memory node from
the imx6qdl.dtsi file and by adding 'device_type = "memory";'
in the board Device Tree.
Converted using the following command:
perl -p0777i -e 's/memory\@10000000 \{\n/memory\@10000000 \{\n\t\tdevice_type = \"memory\";\n/m' `find ./arch/arm/boot/dts -name "imx6*"``
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some SOCs in the i.MX6 family have a USB host controller that is
only capable of the HSIC interface and has no on-board PHY.
To be able to use these controllers, we need to add "usb-nop-xceiv"
dummy PHYs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows a board to specify a custom thermal zone configuration
involving the SoC internal sensor, CPU and GPU nodes without having
to change those nodes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach