Consider the following example:
- regulator-X is provided by device-X.
- regulator-X is a supplier to device-A, device-B and device-C.
- device-A is off/inactive from boot.
- device-B and device-C are left on/active by the bootloader
- regulator-X is left on boot by the bootloader at 2000 mV to supply
device-B and device-C.
Example boot sequence 1:
1. device-X is probed successfully.
2. device-A is probed by driver-A
a. driver-A gets regulator-X
b. driver-A votes on regulator-X
c. driver-A initializes device-A
d. driver-A votes off regulator-X
e. regulator-X is turned off.
3. System crashes or device-B and device-C become unreliable because
regulator-X was turned off without following the proper quiescing
steps for device-B and device-C.
Example boot sequence 2:
1. device-X is probed successfully.
2. device-B is probed by driver-B
a. driver-B gets regulator-X
b. driver-B votes on regulator-X
c. driver-B lowers device-B performance point.
d. driver-B lowers voltage vote to 1000 mV.
e. regulator-X voltage is lowered to 1000 mV.
3. System crashes or device-C becomes unreliable because regulator-X
voltage was lowered to 1000 mV when device-C still needed it at 2000 mV
This patch series makes sure these examples are handled correctly and
system crash or device instability is avoided and the system remains
usable.
More details provided in the commit texts.
v2->v3:
Patch 2/4 - No functional change. Simple refactor.
Patch 3/4
- Was Patch 2/2 in v2.
- Rewrote commit text to hopefully address all previous points.
- Renamed variable/functions. Hope it's clearer.
- Added more comments.
- Added logging
- Fixed timeout functionality.
- Handle exclusive consumers properly
- Handle coupled regulators properly
Patch 4/4 - Prevents voltage from going too low during boot.
v1->v2:
Patch 1/2
- New patch
Patch 2/2
- This was the only patch in v1
- Made the late_initcall_sync timeout a commandline param
- If timeout is set, we also give up waiting for all consumers after
the timeout expires.
- Made every regulator driver add sync_state() support
Saravana Kannan (4):
driver core: Add dev_set_drv_sync_state()
regulator: core: Add destroy_regulator()
regulator: core: Add basic enable/disable support for sync_state()
callbacks
regulator: core: Add voltage support for sync_state() callbacks
drivers/regulator/core.c | 200 ++++++++++++++++++++++++++++---
include/linux/device.h | 12 ++
include/linux/regulator/driver.h | 2 +
3 files changed, 198 insertions(+), 16 deletions(-)
--
2.28.0.rc0.105.gf9edc3c819-goog
When requesting the enable GPIO, the driver should do so with the
correct output level matching some expected state. This is especially
important if the regulator is a critical one, such as a supply for
the boot CPU. This is currently done by checking for the enable-at-boot
property, but this is not documented in the device tree binding, nor
does it match the common regulator properties.
Honor the common regulator-boot-on property by checking the boot_on
constraint setting within the DT probe path. This is the same as what
is done in the fixed regulator driver.
Also add a comment stating that the enable-at-boot property should not
be used.
Fixes: 006694d099 ("regulator: gpio-regulator: Allow use of GPIO controlled regulators though DT")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200720132809.26908-1-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Part of the regulator_get() code is already factored out into
create_regulator(). This patch factors out some of the regulator_put()
code into destroy_regulator() so that create_regulator() has a
corresponding unwind function. Subsequent patches will use this
function.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20200716042053.1927676-3-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Silence documentation build warning by correcting kernel-doc comments.
./include/linux/regulator/machine.h:196: warning: Function parameter or member 'max_uV_step' not described in 'regulation_constraints'
./include/linux/regulator/driver.h:206: warning: Function parameter or member 'resume' not described in 'regulator_ops'
Signed-off-by: Colton Lewis <colton.w.lewis@protonmail.com>
Link: https://lore.kernel.org/r/20200715191438.29312-1-colton.w.lewis@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding the devicetree binding for labibb regulator.
[sumits: cleanup as per review comments and update to yaml]
Signed-off-by: Nisha Kumari <nishakumari@codeaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200622124110.20971-3-sumit.semwal@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm platforms have LAB(LCD AMOLED Boost)/IBB(Inverting Buck Boost)
regulators, labibb for short, which are used as power supply for
LCD Mode displays.
This patch adds labibb regulator driver for pmi8998 PMIC, found on
SDM845 platforms.
[sumits: reworked the driver design as per upstream review]
Signed-off-by: Nisha Kumari <nishakumari@codeaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://lore.kernel.org/r/20200622124110.20971-5-sumit.semwal@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators might need to verify that they have indeed been enabled
after the enable() call is made and enable_time delay has passed.
This is implemented by repeatedly checking is_enabled() upto
poll_enabled_time, waiting for the already calculated enable delay in
each iteration.
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://lore.kernel.org/r/20200622124110.20971-2-sumit.semwal@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is never modified, so make it const to allow the compiler to put it
in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Pi-Hsun Shih <pihsun@chromium.org>
Link: https://lore.kernel.org/r/20200711114409.9911-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Line up descriptions, start description with a lower-case character and
omit old definitions such as quoting the old argument "consumer".
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200708124832.3441649-4-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Kerneldoc validation gets confused if syntax isn't "@.*: ".
Adding the missing colons squashes the following W=1 warnings:
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Rajendra Nayak <rnayak@ti.com>
Link: https://lore.kernel.org/r/20200708124832.3441649-3-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide descriptions for some missing function args and
rename others to match the names used.
Fixes the following W=1 warning(s):
drivers/regulator/devres.c:187: warning: Function parameter or member 'dev' not described in 'devm_regulator_register'
drivers/regulator/devres.c:226: warning: Function parameter or member 'dev' not described in 'devm_regulator_unregister'
drivers/regulator/devres.c:226: warning: Function parameter or member 'rdev' not described in 'devm_regulator_unregister'
drivers/regulator/devres.c:226: warning: Excess function parameter 'regulator' description in 'devm_regulator_unregister'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200708124832.3441649-2-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for COMPILE_TEST while fixing a warning when
no support for device tree is there.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/1c437154873ace65ff738a0ebca511308f1cecc1.camel@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for ON Semiconductor FAN53880 regulator.
The FAN53880 is an I2C porgrammable power management IC (PMIC)
that contains a BUCK (step-down converter), four LDOs (low dropouts)
and one BOOST (step-up converter). It is designed for mobile power
applications.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/20200702210846.31659-2-chf.fritz@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds support for being able to change regulator modes for
the mt6397 regulator. This is needed to allow the voltage scaling
support in the MT8173 SoC to be used on the elm (Acer Chromebook R13)
and hana (several Lenovo Chromebooks) devices.
Without a of_map_mode implementation, the regulator-allowed-modes
devicetree field is skipped, and attempting to change the regulator mode
results in an error:
[ 1.439165] vpca15: mode operation not allowed
Changes in v2:
- Introduce constants in dt-bindings
- Improve conditional readability
Anand K Mistry (4):
regulator: mt6397: Move buck modes into header file
dt-bindings: regulator: mt6397: Document valid modes
regulator: mt6397: Implement of_map_mode
arm64: dts: mediatek: Update allowed mt6397 regulator modes for elm
boards
.../bindings/regulator/mt6397-regulator.txt | 3 +++
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 4 +++-
drivers/regulator/mt6397-regulator.c | 17 ++++++++++++++---
.../regulator/mediatek,mt6397-regulator.h | 15 +++++++++++++++
4 files changed, 35 insertions(+), 4 deletions(-)
create mode 100644 include/dt-bindings/regulator/mediatek,mt6397-regulator.h
--
2.27.0.212.ge8ba1cc988-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
This patchset adds support for being able to change regulator modes for
the da9211 regulator. This is needed to allow the voltage scaling
support in the MT8173 SoC to be used in the elm (Acer Chromebook R13)
and hana (several Lenovo Chromebooks) devices.
Anand K Mistry (4):
regulator: da9211: Move buck modes into header file
dt-bindings: regulator: da9211: Document allowed modes
regulator: da9211: Implement of_map_mode
arm64: dts: mediatek: Update allowed regulator modes for elm boards
.../devicetree/bindings/regulator/da9211.txt | 4 +++
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 4 ++-
drivers/regulator/da9211-regulator.c | 30 +++++++++++++++----
.../regulator/dlg,da9211-regulator.h | 16 ++++++++++
4 files changed, 47 insertions(+), 7 deletions(-)
create mode 100644 include/dt-bindings/regulator/dlg,da9211-regulator.h
--
2.27.0.212.ge8ba1cc988-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The SY8827N from Silergy Corp is a single output DC/DC converter. The
voltage can be controlled via I2C.
Jisheng Zhang (2):
dt-bindings: regulator: add document bindings for sy8827n
regulator: add support for SY8827N regulator
.../bindings/regulator/silergy,sy8827n.yaml | 45 +++++
drivers/regulator/Kconfig | 7 +
drivers/regulator/Makefile | 1 +
drivers/regulator/sy8827n.c | 185 ++++++++++++++++++
4 files changed, 238 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/silergy,sy8827n.yaml
create mode 100644 drivers/regulator/sy8827n.c
--
2.27.0
Use the new .probe_new for mp886x. It does not use the const
struct i2c_device_id * argument, so convert it to utilise the
simplified i2c driver registration.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200702100200.1a4c65d1@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
The null pointer check on regmap that checks for a dev_get_regmap failure
is currently returning -ENOENT if the regmap succeeded. Fix this by adding
in the missing ! operator.
Fixes: 4fe66d5a62 ("regulator: Add support for QCOM PMIC VBUS booster")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference after null check")
Link: https://lore.kernel.org/r/20200702115659.38208-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SY8827N from Silergy Corp is a single output DC/DC converter. The
voltage can be controlled via I2C.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200702171438.20edc523@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Changes in v4:
- Modified qcom,pmic-typec binding to include the SS mux and the DRD remote
endpoint nodes underneath port@1, which is assigned to the SSUSB path
according to usb-connector
- Added usb-connector reference to the typec dt-binding
- Added tags to the usb type c and vbus nodes
- Removed "qcom" tags from type c and vbus nodes
- Modified Kconfig module name, and removed module alias from the typec driver
Changes in v3:
- Fix driver reference to match driver name in Kconfig for
qcom_usb_vbus-regulator.c
- Utilize regulator bitmap helpers for enable, disable and is enabled calls in
qcom_usb_vbus-regulator.c
- Use of_get_regulator_init_data() to initialize regulator init data, and to
set constraints in qcom_usb_vbus-regulator.c
- Remove the need for a local device structure in the vbus regulator driver
Changes in v2:
- Use devm_kzalloc() in qcom_pmic_typec_probe()
- Add checks to make sure return value of typec_find_port_power_role() is
valid
- Added a VBUS output regulator driver, which will be used by the PMIC USB
type c driver to enable/disable the source
- Added logic to control vbus source from the PMIC type c driver when
UFP/DFP is detected
- Added dt-binding for this new regulator driver
- Fixed Kconfig typec notation to match others
- Leave type C block disabled until enabled by a platform DTS
Add the required drivers for implementing type C orientation and role
detection using the Qualcomm PMIC. Currently, PMICs such as the PM8150B
have an integrated type C block, which can be utilized for this. This
series adds the dt-binding, PMIC type C driver, and DTS nodes.
The PMIC type C driver will register itself as a type C port w/ a
registered type C switch for orientation, and will fetch a USB role switch
handle for the role notifications. It will also have the ability to enable
the VBUS output to any connected devices based on if the device is behaving
as a UFP or DFP.
Wesley Cheng (6):
usb: typec: Add QCOM PMIC typec detection driver
dt-bindings: usb: Add Qualcomm PMIC type C controller dt-binding
arm64: boot: dts: qcom: pm8150b: Add node for USB type C block
regulator: Add support for QCOM PMIC VBUS booster
dt-bindings: regulator: Add dt-binding for QCOM PMIC VBUS output
regulator
arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster
.../regulator/qcom,usb-vbus-regulator.yaml | 41 +++
.../bindings/usb/qcom,pmic-typec.yaml | 113 +++++++
arch/arm64/boot/dts/qcom/pm8150b.dtsi | 13 +
arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 4 +
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/qcom_usb_vbus-regulator.c | 97 ++++++
drivers/usb/typec/Kconfig | 12 +
drivers/usb/typec/Makefile | 1 +
drivers/usb/typec/qcom-pmic-typec.c | 275 ++++++++++++++++++
10 files changed, 567 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml
create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
create mode 100644 drivers/regulator/qcom_usb_vbus-regulator.c
create mode 100644 drivers/usb/typec/qcom-pmic-typec.c
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
IPQ6018 SoC uses the PMIC MP5496. SMPA2 and LDOA2 regulator of MP5496
controls the APSS and SDCC voltage scaling respectively. Add support
for the same.
changes since V1:
- Moved YAML conversion to the last as per Mark's comments
Kathiravan T (6):
dt-bindings: soc: qcom: Add IPQ6018 compatible
soc: qcom: smd-rpm: Add IPQ6018 compatible
dt-bindings: regulator: add MP5496 regulator compatible
regulator: qcom_smd: Add MP5496 regulators
dt-bindings: soc: qcom: convert the SMD-RPM document to YAML schema
dt-bindings: regulator: convert QCOM SMD-RPM regulator document to
YAML schema
.../bindings/regulator/qcom,smd-rpm-regulator.txt | 320 ---------------------
.../bindings/regulator/qcom,smd-rpm-regulator.yaml | 106 +++++++
.../devicetree/bindings/soc/qcom/qcom,smd-rpm.txt | 62 ----
.../devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml | 92 ++++++
drivers/regulator/qcom_smd-regulator.c | 34 +++
drivers/soc/qcom/smd-rpm.c | 1 +
6 files changed, 233 insertions(+), 382 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt
create mode 100644 Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml
delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
This driver enables outputs by setting bit EN_BUCKn in the BUCKn_CTRL1
register. However, if bit EN_PIN_CTRLn in the same register is set, the
output is actually enabled only if EN_BUCKn is set AND an enable pin is
active. Since the driver does not touch EN_PIN_CTRLn, the choice is left to
the hardware, which in turn gets this bit from OTP memory, and in absence
of OTP data it uses a default value that is documented in the datasheet for
LP8752x, but not for LP8756x.
Thus the driver doesn't really "know" whether it is actually enabling the
output or not.
In order to make sure activation is always driver-controlled, just clear
the EN_PIN_CTRLn bit. Now all activation solely depend on the EN_BUCKn bit.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20200622204329.11147-2-luca@lucaceresoli.net
Signed-off-by: Mark Brown <broonie@kernel.org>
IPQ6018 SoC uses the PMIC MP5496. SMPA2 and LDOA2 regulator controls the
APSS and SDCC voltage scaling respectively. Add support for the same.
Signed-off-by: Kathiravan T <kathirav@codeaurora.org>
Link: https://lore.kernel.org/r/1592889472-6843-5-git-send-email-kathirav@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
These are never modified, so make them const to allow the compiler to
put them in read-only memory.
Before:
text data bss dec hex filename
20362 2592 152 23106 5a42 drivers/regulator/qcom_spmi-regulator.o
After:
text data bss dec hex filename
21814 1140 152 23106 5a42 drivers/regulator/qcom_spmi-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200629194632.8147-3-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These are never modified, so make them const to allow the compiler to
put them in read-only memory.
Before:
text data bss dec hex filename
17485 500 8 17993 4649 drivers/regulator/qcom_rpm-regulator.o
After:
text data bss dec hex filename
17881 104 8 17993 4649 drivers/regulator/qcom_rpm-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200629194632.8147-2-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This describes how to enable the Qualcomm PMIC VBUS booster used for
providing power to connected USB peripherals when the USB role is host
mode. The driver itself will register the vbus_usb regulator, so that
external drivers can utilize the enable/disable regulator APIs.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20200626185516.18018-6-wcheng@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Qualcomm PMICs have the capability to source the VBUS output to
connected peripherals. This driver will register a regulator to the
regulator list to enable or disable this source by an external driver.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20200626185516.18018-5-wcheng@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This was an upstreaming error. Remove it as it's not to be used.
Fixes the following W=1 kernel build warning:
drivers/regulator/qcom_smd-regulator.c:477:36: warning: ‘pmi8994_boost’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-10-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
W=1 kernel builds report a lack of descriptions for various
function arguments. In reality they are documented, but the
formatting was not as expected '@.*:'. Instead, some weird
arg identifiers were used.
This change fixes the following warnings:
drivers/regulator/wm8400-regulator.c:243: warning: Function parameter or member 'dev' not described in 'wm8400_register_regulator'
drivers/regulator/wm8400-regulator.c:243: warning: Function parameter or member 'reg' not described in 'wm8400_register_regulator'
drivers/regulator/wm8400-regulator.c:243: warning: Function parameter or member 'initdata' not described in 'wm8400_register_regulator'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Link: https://lore.kernel.org/r/20200626065738.93412-9-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
'rid' is declared as unsigned int, so there is little point checking for <0.
Removing these checks fixes the following W=1 warnings:
drivers/regulator/tps65218-regulator.c: In function ‘tps65218_pmic_set_suspend_enable’:
drivers/regulator/tps65218-regulator.c:131:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
131 | if (rid < TPS65218_DCDC_1 || rid > TPS65218_LDO_1)
| ^
drivers/regulator/tps65218-regulator.c: In function ‘tps65218_pmic_set_suspend_disable’:
drivers/regulator/tps65218-regulator.c:144:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
144 | if (rid < TPS65218_DCDC_1 || rid > TPS65218_LDO_1)
| ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-8-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Until now the aforementioned return value has been ignored.
Previous and current calls to tps65217_reg_read() return
instantly when the value is not 0, so let's do that.
Fixes the following W=1 warning:
drivers/regulator/tps65217-regulator.c: In function ‘tps65217_regulator_probe’:
drivers/regulator/tps65217-regulator.c:227:9: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
227 | int i, ret;
| ^~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Russ Dill <Russ.Dill@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-7-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
'rid' is declared as unsigned int, so there is little point checking for <0.
Removing these checks fixes the following W=1 warnings:
drivers/regulator/tps65217-regulator.c: In function ‘tps65217_pmic_set_suspend_enable’:
drivers/regulator/tps65217-regulator.c:127:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
127 | if (rid < TPS65217_DCDC_1 || rid > TPS65217_LDO_4)
| ^
drivers/regulator/tps65217-regulator.c: In function ‘tps65217_pmic_set_suspend_disable’:
drivers/regulator/tps65217-regulator.c:140:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
140 | if (rid < TPS65217_DCDC_1 || rid > TPS65217_LDO_4)
| ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Russ Dill <Russ.Dill@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-6-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In kerneldoc format, data structures have to start with 'struct'
else the kerneldoc tooling/parsers/validators get confused.
Fixes the following W=1 kernel build warning:
drivers/regulator/stpmic1_regulator.c:25: warning: cannot understand function prototype: 'struct stpmic1_regulator_cfg '
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Pascal Paillet <p.paillet@st.com>
Link: https://lore.kernel.org/r/20200626065738.93412-5-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This particular comment doesn't have anything to do with documenting
functions or data structures. Instead it is used as a section header.
Fixes W=1 warning:
drivers/regulator/pwm-regulator.c:55: warning: Function parameter or member 'rdev' not described in 'pwm_regulator_init_state'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200626065738.93412-4-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
W=1 kernel builds report a lack of descriptions for various
enum properties and function arguments. In reality they are
documented, but the formatting was not as expected '@.*:'.
Instead, some weird arg identifiers were used or none at all.
This change fixes the following warnings:
drivers/regulator/qcom-rpmh-regulator.c:33: warning: Enum value 'VRM' not described in enum 'rpmh_regulator_type'
drivers/regulator/qcom-rpmh-regulator.c:33: warning: Enum value 'XOB' not described in enum 'rpmh_regulator_type'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'vreg' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'dev' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'node' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'pmic_id' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'pmic_rpmh_data' not described in 'rpmh_regulator_init_vreg'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-3-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
