This fixes requesting of the MSI-X vectors for the base response queue.
The iteration in the for loop in qla24xx_enable_msix() was incorrect.
We should only iterate of the first two MSI-X vectors and not the total
number of MSI-X vectors that have given to the driver for this device
from pci_enable_msix() in this function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A selective retransmission request (SRR) is a fibre-channel
protocol control request which provides support for requesting
retransmission of a data sequence in response to an issue such as
frame loss or corruption. These events are experienced
infrequently in fibre-channel based networks which makes
it difficult to test and assess codepaths which handle these
events.
We were fortunate enough, for some definition of fortunate, to
have a metro-area single-mode SAN link which, at 10 GBPS
sustained load levels, would consistently generate SRR's in
a SCST based target implementation using our SCST/in-kernel
Qlogic target interface driver. In response to an SRR the
in-kernel Qlogic target driver immediately panics resulting
in a catastrophic storage failure for serviced initiators.
The culprit was a debug statement in the qla_target.c file which
does not verify that a pointer to the SCSI CDB is not null.
The unchecked pointer dereference results in the kernel panic
and resultant system failure.
The other two references to the SCSI CDB by the SRR handling code
use a ternary operator to verify a non-null pointer is being
acted on. This patch simply adds a similar test to the implicated
debug statement.
This patch is a candidate for any stable kernel being maintained
since it addresses a potentially catastrophic event with
minimal downside.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the NAA formatted name used by EVPD=0x83
device identifer to reflect the proper NPIV enabled WWPN.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch performs configfs_depend_item() during TPG enable for
base_tpg (eg: non-NPIV) ports, and configfs_undepend_item() during
TPG disable for base_tpg.
This is done to ensure that any attempt to configfs rmdir a base_tpg
with active NPIV ports will fail with -EBUSY, until all associated
NPIV ports have been explicitly shutdown and base_tpg disabled.
Note that the actual configfs_[un]depend_item() is done from seperate
process context, as these are not intended to be called directly
from configfs callbacks.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds seperate logic for NPIV specific enable/disable
attribute logic, as NPIV vs. non-NPIV enable/disable ends up being
different enough to warrent seperate logic for setting configfs
tpg_group dependencies in the non-NPIV case.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an check to qlt_stop_phase1() to avoid shutdown
when the base_vha contains a non-zero fc_host->npiv_vports_inuse
count.
This includes holding qla_tgt_mutex in qlt_stop_phase1() between
the fc_host->npiv_vports_inuse check + setting of tgt->tgt_stop to
avoid a possible race between qlt_lport_register() -> tcm_qla2xxx
-> tcm_qla2xxx_lport_register_npiv_cb() calling fc_vport_create().
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch closes a race between qlt_lport_register() and
tcm_qla2xxx callback logic by holding qla_tgt_mutex before
making the callback.
In order for this to work, the qlt_add_target() and
qlt_remove_target() code has been changed to avoid the
accessing qla_tgt_mutex + list_[add,del] for NPIV enabled
ports.
This bug introduced in v3.14-rc1 code with commit 49a47f2.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The only place this struct member is touched is in one INIT_LIST_HEAD.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This patch set is a lot of driver updates for qla4xxx, bfa, hpsa, qla2xxx. It
also removes the aic7xxx_old driver (which has been deprecated for nearly a
decade) and adds support for deadlines in error handling.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJS4AfxAAoJEDeqqVYsXL0M8DAIAKRtc9+hy2zsratyvHxxZlz4
6tdvT/4dLTXbIS7EFHmdVb09G5791Pj2jx2PAza/zFDSzgMyL8reXjXpDtCQBvsG
U9CKAGAfJi/vD3QSez2qh0SyvIfCHjatlU3IsM/g+5iFcIOO9+LMJuRlw3qtVqOZ
iQQBATH8cuVW7k1YRHXS5xAO8cVCEYBPuuz0UreVnZijTV5lsRFaObaq8r7S7yVM
4F5eSb5lcgZZLDMDMB0E2KHq12QoLiLQy/ahCqAL1od41v+P90BHC4cIu8jkdB0l
nUYp8vHkmsM82L3xxK9HglcZvJ94fkz6n1gwULl2dTNSYldUnXc/xmocbt0KMf8=
=yko3
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set is a lot of driver updates for qla4xxx, bfa, hpsa,
qla2xxx. It also removes the aic7xxx_old driver (which has been
deprecated for nearly a decade) and adds support for deadlines in
error handling"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (75 commits)
[SCSI] hpsa: allow SCSI mid layer to handle unit attention
[SCSI] hpsa: do not require board "not ready" status after hard reset
[SCSI] hpsa: enable unit attention reporting
[SCSI] hpsa: rename scsi prefetch field
[SCSI] hpsa: use workqueue instead of kernel thread for lockup detection
[SCSI] ipr: increase dump size in ipr driver
[SCSI] mac_scsi: Fix crash on out of memory
[SCSI] st: fix enlarge_buffer
[SCSI] qla1280: Annotate timer on stack so object debug does not complain
[SCSI] qla4xxx: Update driver version to 5.04.00-k3
[SCSI] qla4xxx: Recreate chap data list during get chap operation
[SCSI] qla4xxx: Add support for ISCSI_PARAM_LOCAL_IPADDR sysfs attr
[SCSI] libiscsi: Add local_ipaddr parameter in iscsi_conn struct
[SCSI] scsi_transport_iscsi: Export ISCSI_PARAM_LOCAL_IPADDR attr for iscsi_connection
[SCSI] qla4xxx: Add host statistics support
[SCSI] scsi_transport_iscsi: Add host statistics support
[SCSI] qla4xxx: Added support for Diagnostics MBOX command
[SCSI] bfa: Driver version upgrade to 3.2.23.0
[SCSI] bfa: change FC_ELS_TOV to 20sec
[SCSI] bfa: Observed auto D-port mode instead of manual
...
This patch changes qla2xxx qlt_lport_register() code to accept
target_lport_ptr + npiv_wwpn + npiv_wwnn parameters, and updates
tcm_qla2xxx to use the new tcm_qla2xxx_lport_register_npiv_cb()
callback for invoking fc_vport_create() from configfs context
via tcm_qla2xxx_npiv_make_lport() code.
In order for this to work, the qlt_lport_register() callback is
now called without holding qla_tgt_mutex, as the fc_vport creation
process will call qlt_vport_create() -> qlt_add_target(), which
already expects to acquire it.
It enforces /sys/kernel/config/target/qla2xxx_npiv/$NPIV_WWPN
naming in the following format:
$PHYSICAL_WWPN@$NPIV_WWPN:$NPIV_WWNN
and assumes the $PHYSICAL_WWPN in question has already had been
configured for target mode in non NPIV mode.
Finally, it updates existing tcm_qla2xxx_lport_register_cb() logic
to setup the non NPIV assignments that have now been moved out of
qlt_lport_register() code.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a possible scsi_host reference leak in qlt_lport_register(),
when a non zero return from the passed (*callback) does not call drop the
local reference via scsi_host_put() before returning.
This currently does not effect existing tcm_qla2xxx code as the passed callback
will never fail, but fix this up regardless for future code.
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes a possible scsi_host reference leak in qlt_lport_register(),
when a non zero return from the passed (*callback) does not call drop the
local reference via scsi_host_put() before returning.
This currently does not effect existing tcm_qla2xxx code as the passed callback
will never fail, but fix this up regardless for future code.
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we become disconnected from the PCI bus/PCIe fabric, there can be long delays
in register reads which can cause erroneous decisions to be made and cause a
soft lockup if a lock is held too long. As a preventative measure, check for a
disconnection (register reads that return -1) and then disable the board if we
find ourselves in this condition. For now, check in our interrupt handlers and
the per adapter one second timer.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the execute firmware command fails we do not stop the rest of the
initialization process which will continue to fail so if we encounter an error
simply short circuit the process.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes two cases in qla_target.c code where the
schedule_delayed_work() value was being incorrectly calculated
from sess->expires - jiffies.
Signed-off-by: Shivaram U <shivaram.u@quadstor.com>
Cc: <stable@vger.kernel.org> #3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Things have been quiet this round with mostly bugfixes, percpu
conversions, and other minor iscsi-target conformance testing changes.
The highlights include:
- Add demo_mode_discovery attribute for iscsi-target (Thomas)
- Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
- Add send completion interrupt coalescing for ib_isert
- Convert target-core to use percpu-refcounting for se_lun
- Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
- tcm_loop updates (Hannes)
- target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)
v3.14 is currently shaping to be a busy development cycle in target
land, with initial support for T10 Referrals and T10 DIF currently on
the roadmap"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
iscsi-target: chap auth shouldn't match username with trailing garbage
iscsi-target: fix extract_param to handle buffer length corner case
iscsi-target: Expose default_erl as TPG attribute
target_core_configfs: split up ALUA supported states
target_core_alua: Make supported states configurable
target_core_alua: Store supported ALUA states
target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
target_core_alua: spellcheck
target core: rename (ex,im)plict -> (ex,im)plicit
percpu-refcount: Add percpu-refcount.o to obj-y
iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
iscsi-target: Convert iscsi_session statistics to atomic_long_t
target: Convert se_device statistics to atomic_long_t
target: Fix delayed Task Aborted Status (TAS) handling bug
iscsi-target: Reject unsupported multi PDU text command sequence
ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
target: Core does not need blkdev.h
target: Pass through I/O topology for block backstores
iser-target: Avoid using FRMR for single dma entry requests
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
If an invalid IOCB is returned on the response queue then the index into the
request queue map could be invalid and could return to us a bogus value. This
could cause us to try to deference an invalid pointer and cause an exception.
If we encounter this condition, simply return as no context can be established
for this response.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Just a dereference, don't need a macro.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove a lingering macro that just hid a dereference.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* pci/misc:
PCI: Remove unused PCI_MSIX_FLAGS_BIRMASK definition
PCI: acpiphp_ibm: Convert to dynamic debug
PCI: acpiphp: Convert to dynamic debug
PCI: Remove Intel Haswell D3 delays
PCI: Pass type, width, and prefetchability for window alignment
PCI: Document reason for using pci_is_root_bus()
PCI: Use pci_is_root_bus() to check for root bus
PCI: Remove unused "is_pcie" from pci_dev structure
PCI: Update pci_find_slot() description in pci.txt
[SCSI] qla2xxx: Use standard PCIe Capability Link register field names
PCI: Fix comment typo, remove unnecessary !! in pci_is_pcie()
PCI: Drop "setting latency timer" messages
Use the standard #defines for PCIe Link Capability register fields
rather than bare numbers. This also uses the new PCI Express Capability
accessor rather than reading the capability directly.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity again this round for I/O performance optimizations
(per-cpu IDA pre-allocation for vhost + iscsi/target), and the
addition of new fabric independent features to target-core
(COMPARE_AND_WRITE + EXTENDED_COPY).
The main highlights include:
- Support for iscsi-target login multiplexing across individual
network portals
- Generic Per-cpu IDA logic (kent + akpm + clameter)
- Conversion of vhost to use per-cpu IDA pre-allocation for
descriptors, SGLs and userspace page pointer list
- Conversion of iscsi-target + iser-target to use per-cpu IDA
pre-allocation for descriptors
- Add support for generic COMPARE_AND_WRITE (AtomicTestandSet)
emulation for virtual backend drivers
- Add support for generic EXTENDED_COPY (CopyOffload) emulation for
virtual backend drivers.
- Add support for fast memory registration mode to iser-target (Vu)
The patches to add COMPARE_AND_WRITE and EXTENDED_COPY support are of
particular significance, which make us the first and only open source
target to support the full set of VAAI primitives.
Currently Linux clients are lacking upstream support to actually
utilize these primitives. However, with server side support now in
place for folks like MKP + ZAB working on the client, this logic once
reserved for the highest end of storage arrays, can now be run in VMs
on their laptops"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
target/iscsi: Bump versions to v4.1.0
target: Update copyright ownership/year information to 2013
iscsi-target: Bump default TCP listen backlog to 256
target: Fix >= v3.9+ regression in PR APTPL + ALUA metadata write-out
iscsi-target; Bump default CmdSN Depth to 64
iscsi-target: Remove unnecessary wait_for_completion in iscsi_get_thread_set
iscsi-target: Add thread_set->ts_activate_sem + use common deallocate
iscsi-target: Fix race with thread_pre_handler flush_signals + ISCSI_THREAD_SET_DIE
target: remove unused including <linux/version.h>
iser-target: introduce fast memory registration mode (FRWR)
iser-target: generalize rdma memory registration and cleanup
iser-target: move rdma wr processing to a shared function
target: Enable global EXTENDED_COPY setup/release
target: Add Third Party Copy (3PC) bit in INQUIRY response
target: Enable EXTENDED_COPY setup in spc_parse_cdb
target: Add support for EXTENDED_COPY copy offload emulation
target: Avoid non-existent tg_pt_gp_mem in target_alua_state_check
target: Add global device list for EXTENDED_COPY
target: Make helpers non static for EXTENDED_COPY command setup
target: Make spc_parse_naa_6h_vendor_specific non static
...
Update copyright ownership/year information for target-core,
loopback, iscsi-target, tcm_qla2xx, vhost and iser-target.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reversing the dma_data_direction for pci_map_sg() friends is useful
for other drivers, so move it from tcm_qla2xxx into inline code
within target_core_fabric.h.
Also drop internal usage of equivlient in tcm_qla2xxx fabric code.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
At mailbox/buffer debug level, print the correct values of the
outgoing and incoming mailbox registers.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On any Adapter when we flash through FC/FCoE without card reset option it still
shows the Running FW version in Flashed FW version. This new interface will be
used by API to instruct the driver to update its cache versions.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Unless there is a need to observe them, the queue depth ramp up/down messages
are a nuisance and may cause the system to become unresponsive so move it a
non-default logging level.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver.
We now have to handle the aen so that other protocol drivers can use time
extension during some loopback operations.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
list_for_each_entry() never leaves the iterator pointing to null.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch changes a specifier used to output some variables. Instead of using
stack for each byte the '%*ph[CN]' allows to take a one pointer and prints
entire buffer as a hexadecimal string with the separator ':' or ''.
Signed-off-by: Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changing this attribute to 0 will mean that all initiators that login
to the target while the target has generate_node_acls=1 will see all
TPG LUNs, which may be the desired behavior in some cases.
(nab: Apply patch without macro changes)
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This fixes a regression where Xyratex controllers and disks were lost by the
driver:
https://bugzilla.kernel.org/show_bug.cgi?id=59601
Reported-by: Jack Hill <jackhill@jackhill.us>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is the remaining set of SCSI patches for the merge window. it's mostly
driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There are also several
bug fixes in fcoe, libfc, and megaraid_sas. We also have a couple of core
changes to try to make device destruction more deterministic.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJR4NdLAAoJEDeqqVYsXL0MgLcIAIMpnHPPO0xTB1brAhIA2r4H
MHcD3/iRu+b+YuzEOuErw+pNzsAUGG9MD1b4m74qZ4z9PaVl4U0lWt61++P/OW91
ZD9TAF70t+3/R6Wz2eZp8WqmgWkLcEu9wDQxJKGPCcyWB9MphbsxaakM60B1swCy
5H3VGBWOy8MieLCHzdYgXfB83fnSy/75h/jErDiNwoEUuRci0rb9yOtpNamXPOiB
2JpW8hegixdup6srt+4Uq3gSWKJhqV1MD3leu6i3cHmoqTGueCX46patqlciSLRo
lN8fB3RgZjtIj8zattaeaGchEUMAE7yKcbjC+LyGPQe3+DKVutGNrEFT68KKRcQ=
=7slg
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is the remaining set of SCSI patches for the merge window. It's
mostly driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There
are also several bug fixes in fcoe, libfc, and megaraid_sas. We also
have a couple of core changes to try to make device destruction more
deterministic"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
[SCSI] scsi constants: command, sense key + additional sense strings
fcoe: Reduce number of sparse warnings
fcoe: Stop fc_rport_priv structure leak
libfcoe: Fix meaningless log statement
libfc: Differentiate echange timer cancellation debug statements
libfc: Remove extra space in fc_exch_timer_cancel definition
fcoe: fix the link error status block sparse warnings
fcoe: Fix smatch warning in fcoe_fdmi_info function
libfc: Reject PLOGI from nodes with incompatible role
[SCSI] enable destruction of blocked devices which fail LUN scanning
[SCSI] Fix race between starved list and device removal
[SCSI] megaraid_sas: fix a bug for 64 bit arches
[SCSI] scsi_debug: reduce duplication between prot_verify_read and prot_verify_write
[SCSI] scsi_debug: simplify offset calculation for dif_storep
[SCSI] scsi_debug: invalidate protection info for unmapped region
[SCSI] scsi_debug: fix NULL pointer dereference with parameters dif=0 dix=1
[SCSI] scsi_debug: fix incorrectly nested kmap_atomic()
[SCSI] scsi_debug: fix invalid address passed to kunmap_atomic()
[SCSI] mpt3sas: Bump driver version to v02.100.00.00
[SCSI] mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed
...
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity this round on performance improvements in target-core
while benchmarking the prototype scsi-mq initiator code with
vhost-scsi fabric ports, along with a number of iscsi/iser-target
improvements and hardening fixes for exception path cases post v3.10
merge.
The highlights include:
- Make persistent reservations APTPL buffer allocated on-demand, and
drop per t10_reservation buffer. (grover)
- Make virtual LUN=0 a NULLIO device, and skip allocation of NULLIO
device pages (grover)
- Add transport_cmd_check_stop write_pending bit to avoid extra
access of ->t_state_lock is WRITE I/O submission fast-path. (nab)
- Drop unnecessary CMD_T_DEV_ACTIVE check from
transport_lun_remove_cmd to avoid extra access of ->t_state_lock in
release fast-path. (nab)
- Avoid extra t_state_lock access in __target_execute_cmd fast-path
(nab)
- Drop unnecessary vhost-scsi wait_for_tasks=true usage +
->t_state_lock access in release fast-path. (nab)
- Convert vhost-scsi to use modern se_cmd->cmd_kref
TARGET_SCF_ACK_KREF usage (nab)
- Add tracepoints for SCSI commands being processed (roland)
- Refactoring of iscsi-target handling of ISCSI_OP_NOOP +
ISCSI_OP_TEXT to be transport independent (nab)
- Add iscsi-target SendTargets=$IQN support for in-band discovery
(nab)
- Add iser-target support for in-band discovery (nab + Or)
- Add iscsi-target demo-mode TPG authentication context support (nab)
- Fix isert_put_reject payload buffer post (nab)
- Fix iscsit_add_reject* usage for iser (nab)
- Fix iscsit_sequence_cmd reject handling for iser (nab)
- Fix ISCSI_OP_SCSI_TMFUNC handling for iser (nab)
- Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED (nab)
The last five iscsi/iser-target items are CC'ed to stable, as they do
address issues present in v3.10 code. They are certainly larger than
I'd like for stable patch set, but are important to ensure proper
REJECT exception handling in iser-target for 3.10.y"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
iser-target: Ignore non TEXT + LOGOUT opcodes for discovery
target: make queue_tm_rsp() return void
target: remove unused codes from enum tcm_tmrsp_table
iscsi-target: kstrtou* configfs attribute parameter cleanups
iscsi-target: Fix tfc_tpg_auth_cit configfs length overflow
iscsi-target: Fix tfc_tpg_nacl_auth_cit configfs length overflow
iser-target: Add support for ISCSI_OP_TEXT opcode + payload handling
iser-target: Rename sense_buf_[dma,len] to pdu_[dma,len]
iser-target: Add vendor_err debug output
target: Add (obsolete) checking for PMI/LBA fields in READ CAPACITY(10)
target: Return correct sense data for IO past the end of a device
target: Add tracepoints for SCSI commands being processed
iser-target: Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED
iscsi-target: Fix ISCSI_OP_SCSI_TMFUNC handling for iser
iscsi-target: Fix iscsit_sequence_cmd reject handling for iser
iscsi-target: Fix iscsit_add_reject* usage for iser
iser-target: Fix isert_put_reject payload buffer post
iscsi-target: missing kfree() on error path
iscsi-target: Drop left-over iscsi_conn->bad_hdr
target: Make core_scsi3_update_and_write_aptpl return sense_reason_t
...
Avoid that the fcport structure gets leaked if
bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN, the fcport
allocation succeeds and the !vha->flags.online branch is taken.
This was detected by Coverity. However, Coverity does not recognize
that all qla2x00_process_els() callers specify either
FC_BSG_RPT_ELS or FC_BSG_HST_ELS_NOLOGIN in the field
bsg_job->request->msgcode and that the value of that field is not
modified inside that function. This results in a false positive
report about a possible memory leak in an error path for
bsg_job->request->msgcode values other than the two mentioned
values. Make it easy for Coverity (and for humans) to recognize
that there is no fcport leak in the error path by changing the
bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN test into
bsg_job->request->msgcode != FC_BSG_RPT_ELS.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change the 'rval' variable from QLA_FUNCTION_TIMEOUT into QLA_SUCCESS
before starting a loop that is only executed if rval is initialized
to QLA_SUCCESS. Coverity reported that loop as "dead code".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Coverity reports "Overrunning struct type ct_sns_req of 1228 bytes
by passing it to a function which accesses it at byte offset 8207"
for each qla2x00_prep_ct_req(), qla2x00_prep_ct_fdmi_req() and
qla24xx_prep_ct_fm_req() call. Help Coverity to recognize that
these calls do not trigger a buffer overflow by making it explicit
that these three functions initializes both the request and reply
structures. This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The value of the pointer called "nxt" is not used after the
"nxt = qla24xx_copy_eft(ha, nxt)" statement. Hence keep the function
call but remove the assignment.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since the value of cur_seg is not used and since scsi_prot_sglist()
has no side effects it is safe to remove the statement
"cur_seg = scsi_port_sglist(cmd)". Detected by Coverity.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since ha->model_desc is an array comparing it against NULL is
superfluous. Hence remove these tests.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
At the end of qla2x00_configure_hba() we know that rval == QLA_SUCCESS.
Hence remove the dead code.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove dead code, simplify a pointer computation and move the
ql84_mgmt assignment to just before its first use.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove dead code and simplify a pointer computation.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When we are intentionally generating a firmware dump by executing the
MBC_GEN_SYSTEM_ERROR command, the command actually times out. The normal
course of action when a mailbox command times out is to take a firmware dump.
However, in this special case we do not want to do this since the
MBA_SYSTEM_ERR AEN already generates a firmware dump.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During a chip reset, the mailbox call to get FC statistics from the ISP will
not work resulting in needless mailbox accesses and errors printing out:
qla2xxx [0000:05:00.0]-00af:11: Performing ISP error recovery - ha=ffff881fad044800.
qla2xxx [0000:05:00.0]-1020:11: **** Failed mbx[0]=4001, mb[1]=4953, mb[2]=5020, mb[3]=b100, cmd=6d ****.
qla2xxx [0000:05:00.0]-1020:11: **** Failed mbx[0]=4001, mb[1]=4953, mb[2]=5020, mb[3]=b100, cmd=6d ****.
qla2xxx [0000:05:00.0]-1020:11: **** Failed mbx[0]=4001, mb[1]=4953, mb[2]=5020, mb[3]=b100, cmd=6d ****.
qla2xxx [0000:05:00.0]-1020:11: **** Failed mbx[0]=4001, mb[1]=4953, mb[2]=5020, mb[3]=b100, cmd=6d ****.
qla2xxx [0000:05:00.0]-1020:11: **** Failed mbx[0]=4001, mb[1]=4953, mb[2]=5020, mb[3]=b100, cmd=6d ****.
To prevent this, check for a chip reset when an application queries for FC
stats and return immediately if a chip reset is occurring.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The return value wasn't checked by any of the callers. Assuming this is
correct behaviour, we can simplify some code by not bothering to
generate it.
nab: Add srpt_queue_data_in() + srpt_queue_tm_rsp() nops around
srpt_queue_response() void return
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
related to VLAN tagging FCoE frames.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Sbz8
-----END PGP SIGNATURE-----
Merge tag 'fcoe1' into fixes
This patch fixes a critical bug that was introduced in 3.9
related to VLAN tagging FCoE frames.
Comment from original 2012 patch:
In all our testing this function has never returned true. However, the
dropping of hardware_lock necessary to call this function seems to cause
a use-after-free we manage to hit rather frequently. Given this
cost-benefit ratio, I'm willing to remove some 100 lines of code.
And since the same problem exists around shutdown_sess and put_sess,
this patch changes them from taking the hardware_lock to requiring the
hardware_lock to be taken. In most cases the caller already had the
lock and had to drop it for the called method to reacquire it. At best
that hurts performance and in rare instances it causes races with fatal
consequences.
We dropped the original 2012 patch when upgrading our kernel and it took
us nearly half a year to discover we still need it.
(nab: Fix qla_tgt_sess reference in tcm_qla2xxx_put_sess)
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Suppose an initiator sends a DATA IN command with an allocation length
shorter than the FC transfer length -- we get a target message like
TARGET_CORE[qla2xxx]: Expected Transfer Length: 256 does not match SCSI CDB Length: 0 for SAM Opcode: 0x12
In that case, the target core adjusts the data_length and sets
se_cmd->residual_count for the underrun. But now suppose that command
fails and we end up in tcm_qla2xxx_queue_status() -- that function
unconditionally overwrites residual_count with the already adjusted
data_length, and the initiator will burp with a message like
qla2xxx [0000:00:06.0]-301d:0: Dropped frame(s) detected (0x100 of 0x100 bytes).
Fix this by adding on to the existing underflow residual count instead.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drop unused transport_wait_for_tasks() check in target_wait_for_sess_cmds
shutdown code, and convert tcm_qla2xxx + ib_srpt fabric drivers.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The driver uses ha->mbx_cmd_flags variable to pass information between
its ISR and mailbox routines, however, it does so without the protection of
any locks. Under certain conditions, this can lead to multiple mailbox
command completions being signaled, which, in turn, leads to a false
mailbox timeout error for the subsequently issued mailbox command.
The issue occurs frequently but intermittenly with the Qlogic 8GFC mezz
card during card initialization, resulting in card initialization failure.
Signed-off-by: Gurinder (Sunny) Shergill <gurinder.shergill@hp.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Found by 0 day test project
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
The patch set is mostly driver updates (qla4, qla2 [ISF support updates],
lpfc, aacraid [dual firmware image support]) and a few bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRgAd8AAoJEDeqqVYsXL0Mg5wH/3P4wlXaRyqvyrFk1WSkmklZ
6YxzIKn/RLFmJlJvkaTT7N02ble2UqTluB6+5+AorU/jqz6DArxHsPnyv0/+2pXS
zYmp1hrcLn9dB3sZ2Y32jU2GlzHq+LSJSjjnUrA/uRrq1KTP09KCJtGbZUkvy710
x1/3e3I8u2bvBAehUkKvazg5+xlw/XImJ+IVXgUWOyiv1mNbqNEtT5qYt7sjnhLu
Mg2VfKTSb+kzxSpol3v51vh/wqY6unVcI/a9HxanihkDtkqRBRhg8wXpNAYI2xNK
uNLGq0VFpyCYfBZX0aqh01QZ++EUU2TNlRreVg4/crQnBR88EI3KtUsA1BOthwQ=
=x6dL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James "Jej B" Bottomley:
"The patch set is mostly driver updates (qla4, qla2 [ISF support
updates], lpfc, aacraid [dual firmware image support]) and a few bug
fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] iscsi_tcp: support PF_MEMALLOC/__GFP_MEMALLOC
[SCSI] libiscsi: avoid unnecessary multiple NULL assignments
[SCSI] qla4xxx: Update driver version to 5.03.00-k8
[SCSI] qla4xxx: Added print statements to display AENs
[SCSI] qla4xxx: Use correct value for max flash node entries
[SCSI] qla4xxx: Restrict logout from boot target session using session id
[SCSI] qla4xxx: Use correct flash ddb offset for ISP40XX
[SCSI] isci: add CONFIG_PM_SLEEP to suspend/resume functions
[SCSI] scsi_dh_alua: Add module parameter to allow failover to non preferred path without STPG
[SCSI] qla2xxx: Update the driver version to 8.05.00.03-k.
[SCSI] qla2xxx: Obtain loopback iteration count from bsg request.
[SCSI] qla2xxx: Add clarifying printk to thermal access fail cases.
[SCSI] qla2xxx: Remove duplicated include form qla_isr.c
[SCSI] qla2xxx: Enhancements to support ISPFx00.
[SCSI] qla4xxx: Update driver version to 5.03.00-k7
[SCSI] qla4xxx: Replace dev type macros with generic portal type macros
[SCSI] scsi_transport_iscsi: Declare portal type string macros for generic use
[SCSI] qla4xxx: Add flash node mgmt support
[SCSI] libiscsi: export function iscsi_switch_str_param
[SCSI] scsi_transport_iscsi: Add flash node mgmt support
...
Pull SCSI target update from Nicholas Bellinger:
"The highlights this round include:
- Add fileio support for WRITE_SAME w/ UNMAP=1 discard (asias)
- Add fileio support for UNMAP discard (asias)
- Add tcm_vhost hotplug support to work with upstream QEMU
vhost-scsi-pci code (asias + mst)
- Check for aborted sequence in tcm_fc response path (mdr)
- Add initial iscsit_transport support into iscsi-target code (nab)
- Refactor iscsi-target RX PDU logic + export request PDU handling
(nab)
- Refactor iscsi-target TX queue logic + export response PDU creation
(nab)
- Add new iSCSI Extentions for RDMA (ISER) target driver (Or + nab)
The biggest changes revolve around iscsi-target refactoring in order
to support the iser-target driver. This includes the conversion of
the iscsi-target data-path to use modern se_cmd->cmd_kref counting,
and allowing transport independent aspects of RX/TX PDU
request/response handling be shared across existing traditional
iscsi-target code, and the new iser-target code.
Thanks to Or Gerlitz + Mellanox for supporting the iser-target
development effort!"
* 'for-next-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (25 commits)
iser-target: Add iSCSI Extensions for RDMA (iSER) target driver
tcm_vhost: Enable VIRTIO_SCSI_F_HOTPLUG
tcm_vhost: Add ioctl to get and set events missed flag
tcm_vhost: Add hotplug/hotunplug support
tcm_vhost: Refactor the lock nesting rule
tcm_fc: Check for aborted sequence
iscsi-target: Add iser network portal attribute
iscsi-target: Refactor TX queue logic + export response PDU creation
iscsi-target: Refactor RX PDU logic + export request PDU handling
iscsi-target: Add per transport iscsi_cmd alloc/free
iscsi-target: Add iser-target parameter keys + setup during login
iscsi-target: Initial traditional TCP conversion to iscsit_transport
iscsi-target: Add iscsit_transport API template
target: Add export of target_get_sess_cmd symbol
target: Change default sense key of NOT_READY
target/file: Set is_nonrot attribute
target: Add sbc_execute_unmap() helper
target/iblock: Add iblock_do_unmap() helper
target/file: Add fd_do_unmap() helper
target/file: Add UNMAP emulation support
...
It was already unused when first introduced in 2d70c103.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
qla2x00_loopback_test() was hard setting the loopback iteration
count to 1 rather than obtaining it from the bsg request.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
System crashes, in initiator mode operation, with
qla2xxx_copy_atioqueues() in stack trace when firmware dump is
attempted.
Check for atio_q_length alone does not indicate if atio_ring is
allocated, make explicit check of atio_ring to avoid the crash.
Applicable to ISP24xx, ISP25xx, ISP81xx & ISP83xx line of HBAs.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The original patch was not covering all the adapters and firmwares.
This commit reverts 3a11711ad0.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wait for the IDC complete AEN before returning the loopback operation back to
the application to make sure the port is put back into normal operations.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Give priority to I2C thermal.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side. The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing). As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.
Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Code in qla24xx_report_id_acquisition() incorrectly assumed that
upon completion of list iteration (with no match), the 'pos'
(vp) variable passed to list_for_each_entry() would be set to
NULL. In this context, if the firmware were to return an
unrecognized vp_idx, the follow-on assignments to vp-members
could result in corruption of the structure.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Compiling qla_gs.o (part of the qla2xxx module) triggers two GCC
warnings:
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_rhba’:
drivers/scsi/qla2xxx/qla_gs.c:1339:7: warning: array subscript is above array bounds [-Warray-bounds]
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_register’:
drivers/scsi/qla2xxx/qla_gs.c:1663:15: warning: array subscript is above array bounds [-Warray-bounds]
It seems that the sequence of a strcpy followed by a strlen confuses GCC
when it is keeping track of array bounds here. (It is not clear to me
which array triggers this warning and by how much GCC thinks the
subscript is above its bounds. Neither is it clear to me why comparable
code in these two functions doesn't trigger this warning.)
An easy way to silence these warnings is to use preprocessor macros and
strncpy, as that apparently gives GCC enough information to keep track
of array bounds.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we need to do a chip reset because of a serious loopback error don't try to
reset the loopback mode on the port as the mailbox command will timeout.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the following error handling for loopback diagnostic mode with ISP83xx:
1. If we do not receive an MBA_DCBX_COMPLETE after our initial set port
configuration command, try to reset the port back into normal operation.
If that fails, take a FCoE dump and then reset the chip.
2. After completing the loopback diagnostic operation, if the reset of the port
back into normal operation fails then reset the port so we take a FCoE dump
and then reset the chip.
3. When we receive an IDC notification and the requested operation is loopback
extend the loop down timer so the link does not appear to down for an
extended period of time.
[jejb: fix checkpatch issue]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
BSG code path increments ref count in the send path, but does not
decrement in the return path leading to hang during unload of the
driver.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If another function on the port has initiated a loopback operation do not
process the current request.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the Read SFP mailbox command fails on the thermal device,
print a message explaining that thermal is not supported.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There's a subtle race in the loop/bus-reset handling whereby a
VHA's loop-state can get incorrectly set to 'down' after the
loop-reset and firmware's completion of link re-negotiation. The
original code incorrectly assumes that firmware AENs would arrive
only after mailbox-command execution to initiate the link-flap.
Here's a good case with the old code (AENs arrive after
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:4.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:4.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170b8f315.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
notice how the 'Port database changed' (8014) arrived after the
bus-reset handler completed 'BUS RESET SUCCEEDED'.
Now, here's a failing case with the old code (AENs arrive before
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:0.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:0.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170be9eb2.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
qla2xxx [0000:03:00.1]-281e:91: Needs RSCN update and loop transition.
qla2xxx [0000:03:00.1]-286a:91: qla2x00_configure_loop *** FAILED ***.
qla2xxx [0000:03:00.1]-4810:91: Loop resync end.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
This race would ultimately lead to devices go unexpectedly
offline until another link-flap or chip-reset would cause driver
re-discovery to take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull target updates from Nicholas Bellinger:
"It has been a very busy development cycle this time around in target
land, with the highlights including:
- Kill struct se_subsystem_dev, in favor of direct se_device usage
(hch)
- Simplify reservations code by combining SPC-3 + SCSI-2 support for
virtual backends only (hch)
- Simplify ALUA code for virtual only backends, and remove left over
abstractions (hch)
- Pass sense_reason_t as return value for I/O submission path (hch)
- Refactor MODE_SENSE emulation to allow for easier addition of new
mode pages. (roland)
- Add emulation of MODE_SELECT (roland)
- Fix bug in handling of ExpStatSN wrap-around (steve)
- Fix bug in TMR ABORT_TASK lookup in qla2xxx target (steve)
- Add WRITE_SAME w/ UNMAP=0 support for IBLOCK backends (nab)
- Convert ib_srpt to use modern target_submit_cmd caller + drop
legacy ioctx->kref usage (nab)
- Convert ib_srpt to use modern target_submit_tmr caller (nab)
- Add link_magic for fabric allow_link destination target_items for
symlinks within target_core_fabric_configfs.c code (nab)
- Allocate pointers in instead of full structs for
config_group->default_groups (sebastian)
- Fix 32-bit highmem breakage for FILEIO (sebastian)
All told, hch was able to shave off another ~1K LOC by killing the
se_subsystem_dev abstraction, along with a number of PR + ALUA
simplifications. Also, a nice patch by Roland is the refactoring of
MODE_SENSE handling, along with the addition of initial MODE_SELECT
emulation support for virtual backends.
Sebastian found a long-standing issue wrt to allocation of full
config_group instead of pointers for config_group->default_group[]
setup in a number of areas, which ends up saving memory with big
configurations. He also managed to fix another long-standing BUG wrt
to broken 32-bit highmem support within the FILEIO backend driver.
Thank you again to everyone who contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
target/iscsi_target: Add NodeACL tags for initiator group support
target/tcm_fc: fix the lockdep warning due to inconsistent lock state
sbp-target: fix error path in sbp_make_tpg()
sbp-target: use simple assignment in tgt_agent_rw_agent_state()
iscsi-target: use kstrdup() for iscsi_param
target/file: merge fd_do_readv() and fd_do_writev()
target/file: Fix 32-bit highmem breakage for SGL -> iovec mapping
target: Add link_magic for fabric allow_link destination target_items
ib_srpt: Convert TMR path to target_submit_tmr
ib_srpt: Convert I/O path to target_submit_cmd + drop legacy ioctx->kref
target: Make spc_get_write_same_sectors return sector_t
target/configfs: use kmalloc() instead of kzalloc() for default groups
target/configfs: allocate only 6 slots for dev_cg->default_groups
target/configfs: allocate pointers instead of full struct for default_groups
target: update error handling for sbc_setup_write_same()
iscsit: use GFP_ATOMIC under spin lock
iscsi_target: Remove redundant null check before kfree
target/iblock: Forward declare bio helpers
target: Clean up flow in transport_check_aborted_status()
target: Clean up logic in transport_put_cmd()
...
This patch set includes two large new drivers: mpt3sas (for the next gen
fusion SAS hardware) and csiostor a FCoE offload driver for the Chelsio
converged network cards (this includes some net changes which I've OK'd with
DaveM).
The rest of the patch is driver updates (qla2xxx, lpfc, hptiop, be2iscsi) plus
a few assorted updates and bug fixes.
We also have a Power Management rework in the Upper Layer Drivers preparatory
to doing ACPI zero power optical devices, but the actual enabler is still
being worked on.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQyE9RAAoJEDeqqVYsXL0Mf2oIAL+B2R7hM4RhZrVI0dq1x+og
o/B4JOnDXC7gFJTJXRjejEuAqmJRN7O1mxFV9sEo/zRa++Sd9YVPwQlcCFdesw0a
xU8aCAcy9hLlTcDK2pwhKN6i/anyIvl1Qec/574y9UhFxUsQz+7G9IvT7UmBqaYt
zVTvd4zX4ZHRBIyMTNzkSLGUHcJzKeMOrTFekJwQNDQpHXPJknOCqNiokhLPv0ET
Cl1JZS/jlF7g4FcePhmYyL/nGHfXp1/WYKneDVT7PFWNJc2RPTBDP3PfdN4mBJfc
bQXl/vRLtAjYDpHUJ4IKJbdtfFLkm4KS9ET3kwTkpZ2K6U3c9NklmBK3or2Vo1I=
=Gw2O
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch set includes two large new drivers: mpt3sas (for the next
gen fusion SAS hardware) and csiostor a FCoE offload driver for the
Chelsio converged network cards (this includes some net changes which
I've OK'd with DaveM).
The rest of the patch is driver updates (qla2xxx, lpfc, hptiop,
be2iscsi) plus a few assorted updates and bug fixes.
We also have a Power Management rework in the Upper Layer Drivers
preparatory to doing ACPI zero power optical devices, but the actual
enabler is still being worked on.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (72 commits)
[SCSI] mpt3sas: add new driver supporting 12GB SAS
[SCSI] scsi_transport_sas: add 12GB definitions for mpt3sas
[SCSI] miscdevice: Adding support for MPT3SAS_MINOR(222)
[SCSI] csiostor: remove unneeded memset()
[SCSI] csiostor: Fix sparse warnings.
[SCSI] qla2xxx: Display that driver is operating in legacy interrupt mode.
[SCSI] qla2xxx: Dont clear drv active on iospace config failure.
[SCSI] qla2xxx: Fix typo in qla2xxx driver.
[SCSI] qla2xxx: Update ql2xextended_error_logging parameter description with new option.
[SCSI] qla2xxx: Parameterize the link speed of hba rather than fcport.
[SCSI] qla2xxx: Add 16Gb/s case to get port speed capability.
[SCSI] qla2xxx: Move marking fcport online ahead of setting iiDMA speed.
[SCSI] qla2xxx: Add acquiring of risc semaphore before doing ISP reset.
[SCSI] qla2xxx: Ignore driver ack bit if corresponding presence bit is not set.
[SCSI] qla2xxx: Fix typo in qla83xx_fw_dump function.
[SCSI] qla2xxx: Add Gen3 PCIe speed 8GT/s to the log message.
[SCSI] qla2xxx: Use correct Request-Q-Out register during bidirectional request processing
[SCSI] qla2xxx: Move noisy Start scsi failed messages to verbose logging level.
[SCSI] qla2xxx: Fix coccinelle warnings in qla2x00_relogin.
[SCSI] qla2xxx: No fcport FC-4 type assignment in GA_NXT response.
...
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Update the parameter description for the ql2xextended_error_logging parameter
with the following new option:
0x00008000 - Verbose output
0x00004000 - Target mode
0x00002000 - Target mode management
0x00001000 - Target mode task management
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Parameterize qla2x00_get_link_speed_str() to be generic on link speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Try to acquire the semaphore; if semaphore is hung then acquire it by force.
The ISP reset clears the semaphore, thereby implicitly releasing it.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Original code was not corrected for ISP83xx support. Instead code should used
the cached reference from the req_que structure, rather than the legacy
'if (ISP-TYPE(X))... else if (ISP-TYPE(Y))...' codes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This message can fill up the system logs and is not a common occurrence so move
it to the verbose logging level.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The value of 2 is informational message and it means that port id has
changed. The driver should honor the value and continue its normal course.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rather than returning stale mailbox values.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the qla2xxx driver loses access to multiple, remote ports, there is a race
condition which can occur which will keep the request stuck on a scsi request
queue indefinitely.
This bad state occurred do to a race condition with how the FCPORT_UPDATE_NEEDED
bit is set in qla2x00_schedule_rport_del(), and how it is cleared in
qla2x00_do_dpc(). The problem port has its drport pointer set, but it has never
been processed by the driver to inform the fc transport that the port has been
lost. qla2x00_schedule_rport_del() sets drport, and then sets the
FCPORT_UPDATE_NEEDED bit. In qla2x00_do_dpc(), the port lists are walked and
any drport pointer is handled and the fc transport informed of the port loss,
then the FCPORT_UPDATE_NEEDED bit is cleared. This leaves a race where the
dpc thread is processing one port removal, another port removal is marked
with a call to qla2x00_schedule_rport_del(), and the dpc thread clears the
bit for both removals, even though only the first removal was actually
handled. Until another event occurs to set FCPORT_UPDATE_NEEDED, the later
port removal is never finished and qla2xxx stays in a bad state which causes
requests to become stuck on request queues.
This patch updates the driver to test and clear FCPORT_UPDATE_NEEDED
atomically. This ensures the port state changes are processed and not lost.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC transport on receiving bsg_job submission failure, calls bsg_job->job_done()
and sets the bsg_job->reply->result the returned value. In contrast, when the
success code (0) is returned fc transport doesn't call bsg_job->job_done() and
doesn't populate bsg_job->reply->result.
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: <stable@vger.kernel.org> #3.7
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Search through the list of pending commands on the session list to find
the command the initiator is actually aborting, so that we can pass the
correct LUN to the core TMR handling code.
(nab: Allow abort requests to work to LUN=0 with mainline target code)
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
Pass the sense reason as an explicit return value from the I/O submission
path instead of storing it in struct se_cmd and using negative return
values. This cleans up a lot of the code pathes, and with the sparse
annotations for the new sense_reason_t type allows for much better
error checking.
(nab: Convert spc_emulate_modesense + spc_emulate_modeselect to use
sense_reason_t with Roland's MODE SELECT changes)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It is possible for the target code to change the loop_id or s_id of a
target session in reaction to an FC fabric change. However, the
session structures are stored in tables that are indexed by these two
keys, and if we just change the session structure but leave the
pointers to it in the old places in the table, havoc can ensue. For
example, a new session might come along that should go in the old slot
in the table and overwrite the old session pointer.
To handle this, add a new tgt_ops->update_sess() method that also
updates the "by loop_id" and "by s_id" lookup tables when a session
changes, so that the keys where a session pointer is stored in these
tables always matches the keys in the session structure itself.
(nab: Drop unnecessary double inversion with FCF_CONF_COMP_SUPPORTED
usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
My draft of SPC-4 says the following about the SCSI name string in
inquiry VPD page 83h:
The SCSI NAME STRING field starts with either:
a) the four UTF-8 characters 'eui.' concatenated with 16, 24, or
32 hexadecimal digits (i.e., the UTF-8 characters 0 through 9
and A through F) for an EUI-64 based identifier (see
7.8.6.5). The first hexadecimal digit shall be the most
significant four bits of the first byte (i.e., most significant
byte) of the EUI-64 based identifier;
b) the four UTF-8 characters 'naa.' concatenated with 16 or 32
hexadecimal digits for an NAA identifier (see 7.8.6.6). The
first hexadecimal digit shall be the most significant four bits
of the first byte (i.e., most significant byte) of the NAA
identifier; or
c) the four UTF-8 characters 'iqn.' concatenated with an iSCSI
Name for an iSCSI-name based identifier (see iSCSI).
However, the .tpg_get_wwn method for tcm_qla2xxx formats the WWN so
the SCSI name string looks like "52:4a:93:7d:24:5f:b2:12,t,0x0001".
This patch corrects the code so that VPD 83h gives a SPC-compliant
SCSI name string like "naa.524a937d245fb212,t,0x0001" while leavig
other uses alone (so configfs will still work with ':' separated WWNs).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All other callers of qlt_update_vp_map() already hold ->vport_slock
while updating the vp target map, so go ahead and add the missing
->vport_slock within qla24xx_disable_vp() code.
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roland Dreier <roland@purestorage.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is an assorted set of stragglers into the merge window with driver
updates for megaraid_sas, lpfc, bfi and mvumi. It also includes some fairly
major fixes for virtio-scsi (scatterlist init), scsi_debug (off by one error),
storvsc (use after free) and qla2xxx (potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQeJfDAAoJEDeqqVYsXL0MhqgH/Rq7ebKJvKcUoKsTJKsZ2H0V
iaK5wBvhPBXLxYF5fMEnOwOPT34ry4SWJ7IqTKQqZItx1kqZuG4OTUjmueUCxaMb
7ELFWqyV1z7lyt+XAvNt/RTdMFl3n2SkOxgQJ8kzTPYzEHcE8GCH+dtuqzxoOUqx
styM6DE9Y5cQR1ozacj/QDMv4gn2jclclYgaxR2OTqzqQFeTMzn5KfRH4b6vYtos
ZuYlFE4uaAQhsUGeOqTcGlMvot4tyz4KGO4oy4xkHRQXRVQ52Ve8slRr1z4EUJ3H
rOpz869Y97vnSDFyXuJDa8PpbDd5KOU1uJBxE/3LlCoXIQj4u71hDXETRtq8jtg=
=T50d
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for megaraid_sas, lpfc, bfi and mvumi. It also
includes some fairly major fixes for virtio-scsi (scatterlist init),
scsi_debug (off by one error), storvsc (use after free) and qla2xxx
(potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
[SCSI] storvsc: Account for in-transit packets in the RESET path
[SCSI] qla2xxx: fix potential deadlock on ha->hardware_lock
[SCSI] scsi_debug: Fix off-by-one bug when unmapping region
[SCSI] Shorten the path length of scsi_cmd_to_driver()
[SCSI] virtio-scsi: support online resizing of disks
[SCSI] virtio-scsi: fix LUNs greater than 255
[SCSI] virtio-scsi: initialize scatterlist structure
[SCSI] megaraid_sas: Version, Changelog, Copyright update
[SCSI] megaraid_sas: Remove duplicate code
[SCSI] megaraid_sas: Add SystemPD FastPath support
[SCSI] megaraid_sas: Add array boundary check for SystemPD
[SCSI] megaraid_sas: Load io_request DataLength in bytes
[SCSI] megaraid_sas: Add module param for configurable MSI-X vector count
[SCSI] megaraid_sas: Remove un-needed completion_lock spinlock calls
[SCSI] lpfc 8.3.35: Update lpfc version for 8.3.35 driver release
[SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on
[SCSI] lpfc 8.3.35: Fix error with fabric service parameters causing performance issues
[SCSI] lpfc 8.3.35: Fixed SCSI host create showing wrong link speed on SLI3 HBA ports
[SCSI] lpfc 8.3.35: Fixed not checking solicition in progress bit when verifying FCF record for use
[SCSI] lpfc 8.3.35: Fixed messages for misconfigured port errors
...
Pull scsi target updates from Nicholas Bellinger:
"Things have been calm for the most part with no new fabric drivers in
flight for v3.7 (we're up to eight now !), so this update is primarily
focused on addressing a few long-standing items within target-core and
iscsi-target fabric code.
The highlights include:
- target: Simplify fabric sense data length handling (roland)
- qla2xxx: Fix endianness of task management response code (roland)
- target: fix truncation of mode data, support zero allocation length
(paolo)
- target: Properly support zero-length commands in normal processing
path (paolo)
- iscsi-target: Correctly set 0xffffffff field within ISCSI_OP_REJECT
PDU (ronnie + nab)
- iscsi-target: Add explicit set of cache_dynamic_acls=1 for TPG
demo-mode (ronnie + nab)
- target/file: Re-enable optional fd_buffered_io=1 operation (nab +
hch)
- iscsi-target: Add MaxXmitDataSegmenthLength forr target ->
initiator MDRSL declaration (nab)
- target: Add target_submit_cmd_map_sgls for SGL fabric memory
passthrough (nab + hch)
- tcm_loop: Convert I/O path to use target_submit_cmd_map_sgls (hch +
nab)
- tcm_vhost: Convert I/O path to use target_submit_cmd_map_sgls (nab
+ hch)
The last series for adding a new target_submit_cmd_map_sgls() fabric
caller (as requested by hch) that accepts pre-allocated SGL memory
(using existing logic), along with converting tcm_loop + tcm_vhost has
only been in -next for the last days, but has gotten enough review
+testing and is clear enough a mechanical change that I think it's
reasonable to merge for -rc1 code.
Thanks again to everyone who contributed this round! Extra special
thanks to Roland (PureStorage) for tracking down the qla2xxx target
TMR response code endian issue, and to Paolo (Redhat) for resolving
the long standing zero-length CDB issues within target-core between
virtual and pSCSI backends."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
iscsi-target: Bump defaults for nopin_timeout + nopin_response_timeout values
iscsit: proper endianess conversions
iscsit: use the itt_t abstract type
iscsit: add missing endianess conversion in iscsit_check_inaddr_any
iscsit: remove incorrect unlock in iscsit_build_sendtargets_resp
iscsit: mark various functions static
target/iscsi: precedence bug in iscsit_set_dataout_sequence_values()
target/usb-gadget: strlen() doesn't count the terminator
target/usb-gadget: remove duplicate initialization
tcm_vhost: Convert I/O path to use target_submit_cmd_map_sgls
target: Add control CDB READ payload zero work-around
tcm_loop: Convert I/O path to use target_submit_cmd_map_sgls
target: Add target_submit_cmd_map_sgls for SGL fabric memory passthrough
iscsi-target: Add explicit set of cache_dynamic_acls=1 for TPG demo-mode
iscsi-target: Change iscsi_target_seq_pdu_list.c to honor MaxXmitDataSegmentLength
iscsi-target: Add MaxXmitDataSegmentLength connection recovery check
iscsi-target: Convert incoming PDU payload checks to MaxXmitDataSegmentLength
iscsi-target: Enable MaxXmitDataSegmentLength operation in login path
iscsi-target: Add base MaxXmitDataSegmentLength code
target/file: Re-enable optional fd_buffered_io=1 operation
...
