Document HS and SS data bus for the "usb-role-switch" enabled case.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200920134905.4370-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert ti,hd3ss3220.txt to YAML. Updated the binding documentation
as graph bindings of this device model Super Speed (SS) data bus to
the Super Speed (SS) capable connector.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200920134905.4370-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
-----BEGIN PGP SIGNATURE-----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=U0WQ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into usb-next
Vinod writes:
phy for 5.9
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
* tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
phy: qcom-qmp: initialize the pointer to NULL
phy: qcom-qmp: Add support for sc7180 DP phy
phy: qcom-qmp: Add support for DP in USB3+DP combo phy
phy: qcom-qmp: Use devm_platform_ioremap_resource() to simplify
phy: qcom-qmp: Get dp_com I/O resource by index
phy: qcom-qmp: Move 'serdes' and 'cfg' into 'struct qcom_phy'
phy: qcom-qmp: Remove 'initialized' in favor of 'init_count'
phy: qcom-qmp: Move phy mode into struct qmp_phy
dt-bindings: phy: qcom,qmp-usb3-dp: Add DP phy information
dt-bindings: phy: ti,phy-j721e-wiz: fix bindings for torrent phy
dt-bindings: phy: cdns,torrent-phy: add reset-names
phy: rockchip-dphy-rx0: Include linux/delay.h
phy: fix USB_LGM_PHY warning & build errors
phy: cadence-torrent: Add USB + SGMII/QSGMII multilink configuration
phy: cadence-torrent: Add PCIe + USB multilink configuration
phy: cadence-torrent: Add single link USB register sequences
phy: cadence-torrent: Add single link SGMII/QSGMII register sequences
phy: cadence-torrent: Configure PHY_PLL_CFG as part of link_cmn_vals
phy: cadence-torrent: Add PHY link configuration sequences for single link
phy: cadence-torrent: Add clk changes for multilink configuration
...
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
[1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186
[2] https://lkml.kernel.org/r/27b7545e-8f41-10b8-7c02-e35a08eb1611@i-love.sakura.ne.jp
[3] https://lkml.kernel.org/r/79ba410f-e0ef-2465-b94f-6b9a4a82adf5@i-love.sakura.ne.jp
[4] https://lkml.kernel.org/r/20200530011040.GB12419@rowland.harvard.edu
[5] https://lkml.kernel.org/r/c85331fc-874c-6e46-a77f-0ef1dc075308@i-love.sakura.ne.jp
Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Added small note about why set_registers() can't be used to substitute
set_register().
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-2-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-3-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not an error if the mode can't be entered because
another mode is already active, so no longer printing an
error message if that happens.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200928133324.48841-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Description based on one by Yasushi Asano:
According to 6.7.22 A-UUT “Device No Response” for connection timeout
of USB OTG and EH automated compliance plan v1.2, enumeration failure
has to be detected within 30 seconds. However, the old and new
enumeration schemes each make a total of 12 attempts, and each attempt
can take 5 seconds to time out, so the PET test fails.
This patch adds a new Kconfig option (CONFIG_USB_FEW_INIT_RETRIES);
when the option is set all the initialization retry loops except the
outermost are reduced to a single iteration. This reduces the total
number of attempts to four, allowing Linux hosts to pass the PET test.
The new option is disabled by default to preserve the existing
behavior. The reduced number of retries may fail to initialize a few
devices that currently do work, but for the most part there should be
no change. And in cases where the initialization does fail, it will
fail much more quickly.
Reported-and-tested-by: yasushi asano <yazzep@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152217.GB134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SET_CONFIG_TRIES macro in hub.c is badly named; it controls the
number of port-initialization retry attempts rather than the number of
Set-Configuration attempts. Furthermore, the USE_NEW_SCHEME macro and
use_new_scheme() function are written in a very confusing manner,
making it almost impossible to figure out exactly what they do or
check that they are correct.
This patch renames SET_CONFIG_TRIES to PORT_INIT_TRIES, removes
USE_NEW_SCHEME entirely, and rewrites use_new_scheme() to be much more
transparent, with added comments explaining how it works. The patch
also pulls the single call site of use_new_scheme() out from the
Get-Descriptor retry loop (where it returns the same value each time)
and renames the local variable used to store the result.
The overall effect is a minor cleanup. However, there is one
functional change: If the "use_both_schemes" module parameter isn't
set (by default it is set), the existing code does only two retry
iterations. After this patch it will always perform four, regardless
of the parameter's value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152050.GA134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains:
drivers/phy/qualcomm/phy-qcom-qmp.c:3899 qcom_qmp_phy_probe() error: uninitialized symbol 'dp_cfg'.
drivers/phy/qualcomm/phy-qcom-qmp.c:3900 qcom_qmp_phy_probe() error: uninitialized symbol 'dp_serdes'.
drivers/phy/qualcomm/phy-qcom-qmp.c:3902 qcom_qmp_phy_probe() error: uninitialized symbol 'usb_cfg'.
This is a warning but not a practical one as dp_cfg, dp_serdes and
usb_cfg will be set and used when valid. So we can set the pointers to
NULL to quiesce the warnings.
Fixes: 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201001070911.140019-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=KvWM
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.10 merge window
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (37 commits)
thunderbolt: Capitalize comment on top of QUIRK_FORCE_POWER_LINK_CONTROLLER
thunderbolt: Correct tb_check_quirks() kernel-doc
thunderbolt: Log correct zeroX entries in decode_error()
thunderbolt: Handle ERR_LOCK notification
thunderbolt: Use "if USB4" instead of "depends on" in Kconfig
thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m
thunderbolt: Only stop control channel when entering freeze
thunderbolt: debugfs: Fix uninitialized return in counters_write()
thunderbolt: Add debugfs interface
thunderbolt: No need to warn in TB_CFG_ERROR_INVALID_CONFIG_SPACE
thunderbolt: Introduce tb_switch_is_tiger_lake()
thunderbolt: Introduce tb_switch_is_ice_lake()
thunderbolt: Check for Intel vendor ID when identifying controller
thunderbolt: Introduce tb_port_is_nhi()
thunderbolt: Introduce tb_switch_next_cap()
thunderbolt: Introduce tb_port_next_cap()
thunderbolt: Move struct tb_cap_any to tb_regs.h
thunderbolt: Add runtime PM for Software CM
thunderbolt: Create device links from ACPI description
ACPI: Export acpi_get_first_physical_node() to modules
...
Add the necessary compatible strings and phy data for the sc7180 USB3+DP
combo phy.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200609034623.10844-1-tanmay@codeaurora.org
Link: https://lore.kernel.org/r/20200916231202.3637932-9-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the USB3 + DisplayPort (DP) "combo" phy to the qmp phy
driver. We already have support for the USB3 part of the combo phy, so
most additions are for the DP phy.
Split up the qcom_qmp_phy{enable,disable}() functions into the phy init,
power on, power off, and exit functions that the common phy framework
expects so that the DP phy can add even more phy ops like
phy_calibrate() and phy_configure(). This allows us to initialize the DP
PHY and configure the AUX channel before powering on the PHY at the link
rate that was negotiated during link training.
The general design is as follows:
1) DP controller calls phy_init() to initialize the PHY and configure
the dp_com register region.
2) DP controller calls phy_configure() to tune the link rate and
voltage swing and pre-emphasis settings.
3) DP controller calls phy_power_on() to enable the PLL and power on
the phy.
4) DP controller calls phy_configure() again to tune the voltage swing
and pre-emphasis settings determind during link training.
5) DP controller calls phy_calibrate() some number of times to change
the aux settings if the aux channel times out during link training.
6) DP controller calls phy_power_off() if the link rate is to be
changed and goes back to step 2 to try again at a different link rate.
5) DP controller calls phy_power_off() and then phy_exit() to power
down the PHY when it is done.
The DP PHY contains a PLL that is different from the one used for the
USB3 PHY. Instead of a pipe clk there is a link clk and a pixel clk
output from the DP PLL after going through various dividers. Introduce
clk ops for these two clks that just tell the child clks what the
frequency of the pixel and link are. When the phy link rate is
configured we call clk_set_rate() to update the child clks in the
display clk controller on what rate is in use. The clk frequencies
always differ based on the link rate (i.e. 1.6Gb/s 2.7Gb/s, 5.4Gb/s, or
8.1Gb/s corresponding to various transmission modes like HBR1, HBR2 or
HBR3) so we simply store the link rate and use that to calculate the clk
frequencies.
The PLL enable sequence is a little different from other QMP phy PLLs so
we power on the PLL in qcom_qmp_phy_configure_dp_phy() that gets called
from phy_power_on(). This should probably be split out better so that
each phy has a way to run the final PLL/PHY enable sequence.
This code is based on a submission of this phy and PLL in the drm
subsystem.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200609034623.10844-1-tanmay@codeaurora.org
Link: https://lore.kernel.org/r/20200916231202.3637932-8-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We can use the wrapper API here to save some lines and remove the need
for the 'base' and 'res' local variable.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200916231202.3637932-7-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dp_com resource is always at index 1 according to the dts files in
the kernel. Get this resource by index so that we don't need to make
future additions to the DT binding use 'reg-names'.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200916231202.3637932-6-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The serdes I/O region is where the PLL for the phy is controlled.
Sometimes the PLL is shared between multiple phys, for example in the
PCIe case where there are three phys inside the same wrapper. Other
times the PLL is for a single phy, i.e. some USB3 phys. To complete the
trifecta we have the USB3+DP combo phy where the USB3 and DP phys each
have their own serdes region because they have their own PLL while they
both share a common I/O region pertaining to the USB type-c pinout and
cable orientation.
Let's move the serdes iomem pointer into 'struct qmp_phy' so that we can
correlate PLL control to the phy that uses it. This allows us to support
the USB3+DP combo phy in this driver. This isn't a problem for the
3-lane/phy PCIe phy because there is a common init function that is the
only place the serdes region is programmed.
Furthermore, move the configuration data that contains most of the
register programming sequences to the qmp phy struct. This data isn't
qmp wrapper specific. It is phy specific data used to tune various
settings for things like pre-emphasis, bias, etc.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200916231202.3637932-5-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We already track if any phy inside the qmp wrapper has been initialized
by means of the struct qcom_qmp::init_count member. Let's drop the
duplicate 'initialized' member to simplify the code a bit.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200916231202.3637932-4-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy mode pertains to the phy itself, i.e. 'struct qmp_phy', not the
wrapper, i.e. 'struct qcom_qmp'. Move the phy mode into the phy
structure to more accurately reflect what is going on. This also cleans
up 'struct qcom_qmp' so that it can eventually be the place where qmp
wrapper wide data is located, paving the way for the USB3+DP combo phy.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200916231202.3637932-3-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This binding only describes the USB phy inside the USB3 + DP "combo"
phy. Add information for the DP phy and describe the sub-nodes that
represent the DP and USB3 phys that exist inside the combo wrapper.
Remove reg-names from required properties because it isn't required nor
used by the kernel driver.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: <devicetree@vger.kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200916231202.3637932-2-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For interfaces that lack a union descriptor, probe for a
"combined-interface" before falling back to the call-management
descriptor instead of the other way round.
This allows for the removal of the NO_DATA_INTERFACE quirk and makes the
probe algorithm somewhat easier to follow.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the data-class define provided by USB core and drop the
driver-specific one.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle broken union functional descriptors where the master-interface
doesn't exist or where its class is of neither Communication or Data
type (as required by the specification) by falling back to
"combined-interface" probing.
Note that this still allows for handling union descriptors with switched
interfaces.
This specifically makes the Whistler radio scanners TRX series devices
work with the driver without adding further quirks to the device-id
table.
Reported-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Tested-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ad9d544f2.
Drop bogus sanity check; an interface in the active configuration will
always have a current altsetting assigned by USB core.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, and they can handle data off
of the stack, so move the driver over to using those calls instead,
saving some logic when dynamically allocating memory.
v2: changed API of use usb_control_msg_send() and usb_control_msg_recv()
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-15-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, and they can handle data off
of the stack, so move the driver over to using those calls instead,
saving some logic when dynamically allocating memory.
v2: API change of use usb_control_msg_send() and usb_control_msg_recv()
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-13-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_recv() function can handle data on the stack, as
well as properly detecting short reads, so move to use that function
instead of the older usb_control_msg() call. This ends up removing a
lot of extra lines in the driver.
v2: change API of usb_control_msg_send()
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Link: https://lore.kernel.org/r/20200914153756.3412156-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-12-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, so move the driver over to
using those calls instead, saving some logic in the wrapper functions
that were being used in this driver.
This also resolves a long-staging bug where data on the stack was being
sent in a USB control message, which was not allowed.
v2: API change of usb_control_msg_send()
Cc: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-8-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-11-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_send() call can handle data on the stack, as well as
returning an error if a "short" write happens, so move the driver over
to using that call instead. This ends up removing a helper function
that is no longer needed.
v2: API change in usb_control_msg_send()
Cc: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-7-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-10-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They need to specify how memory is to be allocated,
as control messages need to work in contexts that require GFP_NOIO.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-9-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d6a4992495.
Control messages are needed in contexts when memory allocations
are restricted, such as handling device resets and runtime PM.
For this reason the control message API internally uses GFP_NOIO.
This is a band aid introduced because when we recognized the issue,
the call chains were highly convoluted. Continuing this trend
is not a good idea.
So I am shooting the whole kennel here.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When WIZ wraps a Cadence Torrent PHY (instead of Cadence Sierra PHY)
there is a difference in the refclk-dig node: Torrent only has two
clocks instead of Sierra's four clocks. Add minItems: 2 to solve this.
Additionally, in our use case we only need to use assigned-clock for a
single clock, but the current binding requires either no assigned-clocks
or two. Fix this by adding minItems: 1 to all the assigned-clock
properties.
There was also an extra trailing whitespace, which this patch removes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://lore.kernel.org/r/20200918083743.213874-2-tomi.valkeinen@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add reset-names as a required property.
There are no dts files using torrent phy yet, so it is safe to add a new
required property.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://lore.kernel.org/r/20200918083743.213874-1-tomi.valkeinen@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>