[ Upstream commit 61a7904b6a ]
The gpio-aspeed driver implements an irq_chip which need to be invoked
from hardirq context. Since spin_lock() can sleep with PREEMPT_RT, it is
no longer legal to invoke it while interrupts are disabled.
This also causes lockdep to complain about:
[ 0.649797] [ BUG: Invalid wait context ]
because aspeed_gpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20f94f7f5 ]
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dac08341 ]
When updating Rx and Tx queue kobjects, the queue count should always be
updated to match the queue kobjects count. This was not done in the net
device unregistration path, fix it. Tracking all queue count updates
will allow in a following up patch to detect illegal updates.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8a91863eb ]
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db66abeea3 ]
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported-by: Maximilian Ernestus <maximilian@ernestus.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2ab06d7c4 ]
Using stack-allocated pointers for USB message data don't work.
This driver is almost OK with that, except for the I2C read
logic.
Fix it by using a temporary read buffer, just like on all other
calls to m920x_read().
Link: https://lore.kernel.org/all/ccc99e48-de4f-045e-0fe4-61e3118e3f74@mida.se/
Reported-by: rkardell@mida.se
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 348df80353 ]
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. In hexium_detach(), saa7146_vv_release()
will be called and there is a dereference of dev->vv_data in
saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init() according to the following logic.
Both hexium_attach() and hexium_detach() are callback functions of
the variable 'extension', so there exists a possible call chain directly
from hexium_attach() to hexium_detach():
hexium_attach(dev, info) -- fail to alloc memory to dev->vv_data
| in saa7146_vv_init().
|
|
hexium_detach() -- a dereference of dev->vv_data in saa7146_vv_release()
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_ORION=m show no new warnings,
and our static analyzer no longer warns about this code.
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ed7d2f61 ]
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71d5049b05 ]
Move the switching code into a function so that it can be re-used and
add a global TLB flush. This makes sure that usage of memory which is
not mapped in the trampoline page-table is reliably caught.
Also move the clearing of CR4.PCIDE before the CR3 switch because the
cr4_clear_bits() function will access data not mapped into the
trampoline page-table.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211202153226.22946-4-joro@8bytes.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1cb3476e4 ]
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.
The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ
The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.
Attached is the KASAN report from fuzzing.
BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227
CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
__kasan_report.cold+0x37/0x7c
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
kasan_report+0xe/0x20
rsi_read_pkt+0x42e/0x500 [rsi_91x]
rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb]
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __wake_up_common+0x10b/0x520
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b07e3c6ebc ]
When freeing rx_cb->rx_skb, the pointer is not set to NULL,
a later rsi_rx_done_handler call will try to read the freed
address.
This bug will very likley lead to double free, although
detected early as use-after-free bug.
The bug is triggerable with a compromised/malfunctional usb
device. After applying the patch, the same input no longer
triggers the use-after-free.
Attached is the kasan report from fuzzing.
BUG: KASAN: use-after-free in rsi_rx_done_handler+0x354/0x430 [rsi_usb]
Read of size 4 at addr ffff8880188e5930 by task modprobe/231
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__kasan_report.cold+0x37/0x7c
? dma_direct_unmap_page+0x90/0x110
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
kasan_report+0xe/0x20
rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __usb_hcd_giveback_urb+0x380/0x380
? apic_timer_interrupt+0xa/0x20
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
? handle_irq_event+0xcd/0x157
? handle_edge_irq+0x1eb/0x7b0
irq_exit+0x114/0x140
do_IRQ+0x91/0x1e0
common_interrupt+0xf/0xf
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxQL/vIiYcZUu/j@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04d80663f6 ]
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1ee1c08fc ]
cl is freed on error of calling device_register, but this
object is return later, which will cause uaf issue. Fix it
by return NULL on error.
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdfd6ab8fd ]
If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.
I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.
Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1020d3cf4 ]
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
[1]
BUG: Bad page state in process devlink pfn:22f73d
page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x2ffff00000000000()
raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
Modules linked in:
CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44
Hardware name: Marvell Armada 7040 TX4810M (DT)
Call trace:
dump_backtrace+0x0/0x1d0
show_stack+0x1c/0x28
dump_stack+0xbc/0x118
bad_page+0xcc/0xf8
check_free_page_bad+0x80/0x88
__free_pages_ok+0x3f8/0x418
__free_pages+0x38/0x60
kmem_freepages+0x200/0x2a8
slab_destroy+0x28/0x68
slabs_destroy+0x60/0x90
___cache_free+0x1b4/0x358
kfree+0xc0/0x1d0
skb_free_head+0x2c/0x38
skb_release_data+0x110/0x1a0
skb_release_all+0x2c/0x38
consume_skb+0x38/0x130
__dev_kfree_skb_any+0x44/0x50
mlxsw_pci_rdq_fini+0x8c/0xb0
mlxsw_pci_queue_fini.isra.0+0x28/0x58
mlxsw_pci_queue_group_fini+0x58/0x88
mlxsw_pci_aqs_fini+0x2c/0x60
mlxsw_pci_fini+0x34/0x50
mlxsw_core_bus_device_unregister+0x104/0x1d0
mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48
devlink_reload+0x44/0x158
devlink_nl_cmd_reload+0x270/0x290
genl_rcv_msg+0x188/0x2f0
netlink_rcv_skb+0x5c/0x118
genl_rcv+0x3c/0x50
netlink_unicast+0x1bc/0x278
netlink_sendmsg+0x194/0x390
__sys_sendto+0xe0/0x158
__arm64_sys_sendto+0x2c/0x38
el0_svc_common.constprop.0+0x70/0x168
do_el0_svc+0x28/0x88
el0_sync_handler+0x88/0x190
el0_sync+0x140/0x180
[2]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html
[3]
https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd1d6da17c ]
Version 2.40a supports DDR_ECC_INTR_SUPPORT for a quirk, so use that
quirk to determine a call to setup_address_map().
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lkml.kernel.org/r/20211012190709.1504152-1-dinguyen@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5fe7864d8 ]
When a keyboard without a function key is detected, instead of removing
all quirks, remove only the APPLE_HAS_FN quirk.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc30c3b0c8 ]
The Lenovo Yoga Book X91F/L uses a panel which has been mounted
90 degrees rotated. Add a quirk for this.
Cc: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Ser <contact@emersion.fr>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106130227.11927-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c76ef96fc0 ]
Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.
The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.
It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1636712682-1226-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9057d6c23e ]
Currently, creating a batman-adv interface in an unprivileged LXD
container and attaching secondary interfaces to it with "ip" or "batctl"
works fine. However all batctl debug and configuration commands
fail:
root@container:~# batctl originators
Error received: Operation not permitted
root@container:~# batctl orig_interval
1000
root@container:~# batctl orig_interval 2000
root@container:~# batctl orig_interval
1000
To fix this change the generic netlink permissions from GENL_ADMIN_PERM
to GENL_UNS_ADMIN_PERM. This way a batman-adv interface is fully
maintainable as root from within a user namespace, from an unprivileged
container.
All except one batman-adv netlink setting are per interface and do not
leak information or change settings from the host system and are
therefore save to retrieve or modify as root from within an unprivileged
container.
"batctl routing_algo" / BATADV_CMD_GET_ROUTING_ALGOS is the only
exception: It provides the batman-adv kernel module wide default routing
algorithm. However it is read-only from netlink and an unprivileged
container is still not allowed to modify
/sys/module/batman_adv/parameters/routing_algo. Instead it is advised to
use the newly introduced "batctl if create routing_algo RA_NAME" /
IFLA_BATADV_ALGO_NAME to set the routing algorithm on interface
creation, which already works fine in an unprivileged container.
Cc: Tycho Andersen <tycho@tycho.pizza>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85744f2d93 ]
Fix following coccicheck warning:
./arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c:156:1-33: Function
for_each_matching_node_and_match should have of_node_put() before break
and goto.
Early exits from for_each_matching_node_and_match() should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211018014503.7598-1-wanjiabing@vivo.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d2271d2fb ]
There have been reports of the WFI timing out on some boards, and a
patch was proposed to just remove it. This stuff is rather fragile,
and I believe the WFI might be needed with our FW prior to GM200.
However, we probably should not be touching PMU during init on GPUs
where we depend on NVIDIA FW, outside of limited circumstances, so
this should be a somewhat safer change that achieves the desired
result.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/10
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae80b60338 ]
Unexpected WDCMSG_TARGET_START replay can lead to null-ptr-deref
when ar->tx_cmd->odata is NULL. The patch adds a null check to
prevent such case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
ar5523_cmd+0x46a/0x581 [ar5523]
ar5523_probe.cold+0x1b7/0x18da [ar5523]
? ar5523_cmd_rx_cb+0x7a0/0x7a0 [ar5523]
? __pm_runtime_set_status+0x54a/0x8f0
? _raw_spin_trylock_bh+0x120/0x120
? pm_runtime_barrier+0x220/0x220
? __pm_runtime_resume+0xb1/0xf0
usb_probe_interface+0x25b/0x710
really_probe+0x209/0x5d0
driver_probe_device+0xc6/0x1b0
device_driver_attach+0xe2/0x120
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START,
I got the null-ptr-deref bug. I believe the bug is triggerable whenever
cmd->odata is NULL. After patching, I tested with the same input and no
longer see the KASAN report.
This was NOT tested on a real device.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXsmPQ3awHFLuAj2@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c2e3bf68f ]
This patch fixes the following crash by receiving a invalid message:
[ 160.672220] ==================================================================
[ 160.676206] BUG: KASAN: user-memory-access in dlm_user_add_ast+0xc3/0x370
[ 160.679659] Read of size 8 at addr 00000000deadbeef by task kworker/u32:13/319
[ 160.681447]
[ 160.681824] CPU: 10 PID: 319 Comm: kworker/u32:13 Not tainted 5.14.0-rc2+ #399
[ 160.683472] Hardware name: Red Hat KVM/RHEL-AV, BIOS 1.14.0-1.module+el8.6.0+12648+6ede71a5 04/01/2014
[ 160.685574] Workqueue: dlm_recv process_recv_sockets
[ 160.686721] Call Trace:
[ 160.687310] dump_stack_lvl+0x56/0x6f
[ 160.688169] ? dlm_user_add_ast+0xc3/0x370
[ 160.689116] kasan_report.cold.14+0x116/0x11b
[ 160.690138] ? dlm_user_add_ast+0xc3/0x370
[ 160.690832] dlm_user_add_ast+0xc3/0x370
[ 160.691502] _receive_unlock_reply+0x103/0x170
[ 160.692241] _receive_message+0x11df/0x1ec0
[ 160.692926] ? rcu_read_lock_sched_held+0xa1/0xd0
[ 160.693700] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 160.694427] ? lock_acquire+0x175/0x400
[ 160.695058] ? do_purge.isra.51+0x200/0x200
[ 160.695744] ? lock_acquired+0x360/0x5d0
[ 160.696400] ? lock_contended+0x6a0/0x6a0
[ 160.697055] ? lock_release+0x21d/0x5e0
[ 160.697686] ? lock_is_held_type+0xe0/0x110
[ 160.698352] ? lock_is_held_type+0xe0/0x110
[ 160.699026] ? ___might_sleep+0x1cc/0x1e0
[ 160.699698] ? dlm_wait_requestqueue+0x94/0x140
[ 160.700451] ? dlm_process_requestqueue+0x240/0x240
[ 160.701249] ? down_write_killable+0x2b0/0x2b0
[ 160.701988] ? do_raw_spin_unlock+0xa2/0x130
[ 160.702690] dlm_receive_buffer+0x1a5/0x210
[ 160.703385] dlm_process_incoming_buffer+0x726/0x9f0
[ 160.704210] receive_from_sock+0x1c0/0x3b0
[ 160.704886] ? dlm_tcp_shutdown+0x30/0x30
[ 160.705561] ? lock_acquire+0x175/0x400
[ 160.706197] ? rcu_read_lock_sched_held+0xa1/0xd0
[ 160.706941] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 160.707681] process_recv_sockets+0x32/0x40
[ 160.708366] process_one_work+0x55e/0xad0
[ 160.709045] ? pwq_dec_nr_in_flight+0x110/0x110
[ 160.709820] worker_thread+0x65/0x5e0
[ 160.710423] ? process_one_work+0xad0/0xad0
[ 160.711087] kthread+0x1ed/0x220
[ 160.711628] ? set_kthread_struct+0x80/0x80
[ 160.712314] ret_from_fork+0x22/0x30
The issue is that we received a DLM message for a user lock but the
destination lock is a kernel lock. Note that the address which is trying
to derefence is 00000000deadbeef, which is in a kernel lock
lkb->lkb_astparam, this field should never be derefenced by the DLM
kernel stack. In case of a user lock lkb->lkb_astparam is lkb->lkb_ua
(memory is shared by a union field). The struct lkb_ua will be handled
by the DLM kernel stack but on a kernel lock it will contain invalid
data and ends in most likely crashing the kernel.
It can be reproduced with two cluster nodes.
node 2:
dlm_tool join test
echo "862 fooobaar 1 2 1" > /sys/kernel/debug/dlm/test_locks
echo "862 3 1" > /sys/kernel/debug/dlm/test_waiters
node 1:
dlm_tool join test
python:
foo = DLM(h_cmd=3, o_nextcmd=1, h_nodeid=1, h_lockspace=0x77222027, \
m_type=7, m_flags=0x1, m_remid=0x862, m_result=0xFFFEFFFE)
newFile = open("/sys/kernel/debug/dlm/comms/2/rawmsg", "wb")
newFile.write(bytes(foo))
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a4bb6a8e9 ]
Fault injection test report debugfs entry leak as follows:
debugfs: Directory 'hci0' with parent 'bluetooth' already present!
When register_pm_notifier() failed in hci_register_dev(), the debugfs
create by debugfs_create_dir() do not removed in the error handing path.
Add the remove debugfs code to fix it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94a4950a4a ]
The cell_count field of of_phandle_iterator is the number of cells we
expect in the phandle arguments list when cells_name is missing. The
error message should show the number of cells we actually see.
Fixes: af3be70a32 ("of: Improve of_phandle_iterator_next() error message")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/96519ac55be90a63fa44afe01480c30d08535465.1640881913.git.baruch@tkos.co.il
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e375b9c929 ]
The API for ib_query_qp requires the driver to set cur_qp_state on return,
add the missing set.
Fixes: 67bbc05512 ("RDMA/cxgb4: Add query_qp support")
Link: https://lore.kernel.org/r/20211220152530.60399-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f03055d50 ]
The MIPS BMC63XX subarch does not provide/support clk_set_parent().
This causes build errors in a few drivers, so add a simple implementation
of that function so that callers of it will build without errors.
Fixes these build errors:
ERROR: modpost: "clk_set_parent" [sound/soc/jz4740/snd-soc-jz4740-i2s.ko] undefined!
ERROR: modpost: "clk_set_parent" [sound/soc/atmel/snd-soc-atmel-i2s.ko] undefined!
Fixes: e7300d04bd ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs." )
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76f66dfd60 ]
Provide a simple implementation of clk_set_parent() in the lantiq
subarch so that callers of it will build without errors.
Fixes these build errors:
ERROR: modpost: "clk_set_parent" [sound/soc/jz4740/snd-soc-jz4740-i2s.ko] undefined!
ERROR: modpost: "clk_set_parent" [sound/soc/atmel/snd-soc-atmel-i2s.ko] undefined!
Fixes: 171bb2f19e ("MIPS: Lantiq: Add initial support for Lantiq SoCs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
--to=linux-mips@vger.kernel.org --cc="John Crispin <john@phrozen.org>" --cc="Jonathan Cameron <jic23@kernel.org>" --cc="Russell King <linux@armlinux.org.uk>" --cc="Andy Shevchenko <andy.shevchenko@gmail.com>" --cc=alsa-devel@alsa-project.org --to="Thomas Bogendoerfer <tsbogend@alpha.franken.de>"
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcee5ce50b ]
When firmware load failed, kernel report task hung as follows:
INFO: task xrun:5191 blocked for more than 147 seconds.
Tainted: G W 5.16.0-rc5-next-20211220+ #11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:xrun state:D stack: 0 pid: 5191 ppid: 270 flags:0x00000004
Call Trace:
__schedule+0xc12/0x4b50 kernel/sched/core.c:4986
schedule+0xd7/0x260 kernel/sched/core.c:6369 (discriminator 1)
schedule_timeout+0x7aa/0xa80 kernel/time/timer.c:1857
wait_for_completion+0x181/0x290 kernel/sched/completion.c:85
lattice_ecp3_remove+0x32/0x40 drivers/misc/lattice-ecp3-config.c:221
spi_remove+0x72/0xb0 drivers/spi/spi.c:409
lattice_ecp3_remove() wait for signals from firmware loading, but when
load failed, firmware_load() does not send this signal. This cause
device remove hung. Fix it by sending signal even if load failed.
Fixes: 781551df57 ("misc: Add Lattice ECP3 FPGA configuration via SPI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20211228125522.3122284-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ecb46755e ]
Because of the potential failure of the ioremap(), the buf->area could
be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.
Fixes: f09aecd50f ("ASoC: SAMSUNG: Add I2S0 internal dma driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211228034026.1659385-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9de2b9286a ]
Yes, you are right and now the return code depending on the
init_clks().
Fixes: 6078c65194 ("soc: mediatek: Refine scpsys to support multiple platform")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211222015157.1025853-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7061627d7 ]
It turns out to be possible for hotplugging out a device to reach the
stage of tearing down the device's group and default domain before the
domain's flush queue has drained naturally. At this point, it is then
possible for the timeout to expire just before the del_timer() call
in free_iova_flush_queue(), such that we then proceed to free the FQ
resources while fq_flush_timeout() is still accessing them on another
CPU. Crashes due to this have been observed in the wild while removing
NVMe devices.
Close the race window by using del_timer_sync() to safely wait for any
active timeout handler to finish before we start to free things. We
already avoid any locking in free_iova_flush_queue() since the FQ is
supposed to be inactive anyway, so the potential deadlock scenario does
not apply.
Fixes: 9a005a800a ("iommu/iova: Add flush timer")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[ rm: rewrite commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0a365e5b07f14b7344677ad6a9a734966a8422ce.1639753638.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 134c37fa25 ]
The last driver referencing the slave_id on Marvell PXA and MMP platforms
was the SPI driver, but this stopped doing so a long time ago, so the
TODO from the earlier patch can no be removed.
Fixes: b729bf3453 ("spi/pxa2xx: Don't use slave_id of dma_slave_config")
Fixes: 13b3006b8e ("dma: mmp_pdma: add filter function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-7-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc058a72f ]
stm32's clk driver register two ltdc gate clk to clk core by
clk_hw_register_gate() and clk_hw_register_composite()
first: 'stm32f429_gates[]', clk name is 'ltdc', which no user to use.
second: 'stm32f429_aux_clk[]', clk name is 'lcd-tft', used by ltdc driver
both of them point to the same offset of stm32's RCC register. after
kernel enter console, clk core turn off ltdc's clk as 'stm32f429_gates[]'
is no one to use. but, actually 'stm32f429_aux_clk[]' is in use.
stm32f469/746/769 have the same issue, fix it.
Fixes: daf2d117cb ("clk: stm32f4: Add lcd-tft clock")
Link: https://lore.kernel.org/linux-arm-kernel/1590564453-24499-7-git-send-email-dillon.minfei@gmail.com/
Link: https://lore.kernel.org/lkml/CAPTRvHkf0cK_4ZidM17rPo99gWDmxgqFt4CDUjqFFwkOeQeFDg@mail.gmail.com/
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/1635232282-3992-10-git-send-email-dillon.minfei@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2167c0b205 ]
The return value of device_property_read_u32_array() is not always 0.
To catch the exception in case that devm_kzalloc failed and the
rt5663->imp_table was NULL, which caused the failure of
device_property_read_u32_array.
Fixes: 450f0f6a8f ("ASoC: rt5663: Add the manual offset field to compensate the DC offset")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211215031550.70702-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20679094a0 ]
Currently, when cma_resolve_ib_dev() searches for a matching GID it will
stop searching after encountering the first empty GID table entry. This
behavior is wrong since neither IB nor RoCE spec enforce tightly packed
GID tables.
For example, when the matching valid GID entry exists at index N, and if a
GID entry is empty at index N-1, cma_resolve_ib_dev() will fail to find
the matching valid entry.
Fix it by making cma_resolve_ib_dev() continue searching even after
encountering missing entries.
Fixes: f17df3b0de ("RDMA/cma: Add support for AF_IB to rdma_resolve_addr()")
Link: https://lore.kernel.org/r/b7346307e3bb396c43d67d924348c6c496493991.1639055490.git.leonro@nvidia.com
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483d805191 ]
Currently, ib_find_gid() will stop searching after encountering the first
empty GID table entry. This behavior is wrong since neither IB nor RoCE
spec enforce tightly packed GID tables.
For example, when a valid GID entry exists at index N, and if a GID entry
is empty at index N-1, ib_find_gid() will fail to find the valid entry.
Fix it by making ib_find_gid() continue searching even after encountering
missing entries.
Fixes: 5eb620c81c ("IB/core: Add helpers for uncached GID and P_Key searches")
Link: https://lore.kernel.org/r/e55d331b96cecfc2cf19803d16e7109ea966882d.1639055490.git.leonro@nvidia.com
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b149d5d45a ]
Commit df1f679d19 ("powerpc/powermac: Add missing
lockdep_register_key()") fixed a problem that was causing a WARNING.
There are two other places in the same file with the same problem
originating from commit 9e607f7274 ("i2c_powermac: shut up lockdep
warning").
Add missing lockdep_register_key()
Fixes: 9e607f7274 ("i2c_powermac: shut up lockdep warning")
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Depends-on: df1f679d19 ("powerpc/powermac: Add missing lockdep_register_key()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200055
Link: https://lore.kernel.org/r/2c7e421874e21b2fb87813d768cf662f630c2ad4.1638984999.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29bbc35e29 ]
pci_irq_vector() and pci_irq_get_affinity() use the list position to find the
MSI-X descriptor at a given index. That's correct for the normal case where
the entry number is the same as the list position.
But it's wrong for cases where MSI-X was allocated with an entries array
describing sparse entry numbers into the hardware message descriptor
table. That's inconsistent at best.
Make it always check the entry number because that's what the zero base
index really means. This change won't break existing users which use a
sparse entries array for allocation because these users retrieve the Linux
interrupt number from the entries array after allocation and none of them
uses pci_irq_vector() or pci_irq_get_affinity().
Fixes: aff171641d ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210223.929792157@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21ad0e4908 ]
The driver data pointer must be set before any callbacks are registered
that use that pointer. Hence move the initialization of that pointer from
after the ufshcd_init() call to inside ufshcd_init().
Link: https://lore.kernel.org/r/20211203231950.193369-7-bvanassche@acm.org
Fixes: 3b1d05807a ("[SCSI] ufs: Segregate PCI Specific Code")
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9abe2ac834 ]
Table descriptors were being installed without properly formatting the
address using paddr_to_iopte, which does not match up with the
iopte_deref in __arm_lpae_map. This is incorrect for the LPAE pte
format, as it does not handle the high bits properly.
This was found on Apple T6000 DARTs, which require a new pte format
(different shift); adding support for that to
paddr_to_iopte/iopte_to_paddr caused it to break badly, as even <48-bit
addresses would end up incorrect in that case.
Fixes: 6c89928ff7 ("iommu/io-pgtable-arm: Support 52-bit physical address")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211120031343.88034-1-marcan@marcan.st
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe6b186924 ]
If a memory copy function fails to copy the whole buffer,
a positive integar with the remaining bytes is returned.
In binder_translate_fd_array() this can result in an fd being
skipped due to the failed copy, but the loop continues
processing fds since the early return condition expects a
negative integer on error.
Fix by returning "ret > 0 ? -EINVAL : ret" to handle this case.
Fixes: bb4a2e48d5 ("binder: return errors from buffer copy functions")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211130185152.437403-2-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5912cc19a ]
Using MKWORD() on a byte-sized variable results in OOB read. Expand the
size of the reserved area so both MKWORD and MKBYTE continue to work
without overflow. Silences this warning on a -Warray-bounds build:
drivers/char/mwave/3780i.h:346:22: error: array subscript 'short unsigned int[0]' is partly outside array bounds of 'DSP_ISA_SLAVE_CONTROL[1]' [-Werror=array-bounds]
346 | #define MKWORD(var) (*((unsigned short *)(&var)))
| ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/char/mwave/3780i.h:356:40: note: in definition of macro 'OutWordDsp'
356 | #define OutWordDsp(index,value) outw(value,usDspBaseIO+index)
| ^~~~~
drivers/char/mwave/3780i.c:373:41: note: in expansion of macro 'MKWORD'
373 | OutWordDsp(DSP_IsaSlaveControl, MKWORD(rSlaveControl));
| ^~~~~~
drivers/char/mwave/3780i.c:358:31: note: while referencing 'rSlaveControl'
358 | DSP_ISA_SLAVE_CONTROL rSlaveControl;
| ^~~~~~~~~~~~~
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211203084206.3104326-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
