Commit graph

54227 commits

Author SHA1 Message Date
Sergei Shtylyov
e51e2528d5 cmd64x: interrupt status fixes (take 2)
The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Sergei Shtylyov
60e7a82f1a cmd64x: fix multiword and remove single-word DMA support
Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think).  In order to do it, a number of changes was necessary:

- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
  total/active times instead of the clock counts, and convert them into the
  active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
  quantize_timing() to also move;

- contrarywise, move all the code handling the address setup timing into
  cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;

- remove from the speedproc() method the  bogus code pretending to set the DMA
  timings by twiddling bits in the BMIDE status register, handle setting MWDMA
  by just calling program_cycle_times(); while at it, improve the style of that
  whole switch statement;

- stop fiddling with the DMA capable bits in the speedproc() method -- they do
  not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;

- don't set hwif->swdma_mask in the init_hwif() method anymore.

In addition to those changes, do the following:

- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
  status bit, eliminate local_irq_{save|restore}() around this code as there's
  *no* actual race with the interrupt handler, and move cmdprintk() to a more
  fitting place -- after ide_get_best_pio_mode() call;

- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;

- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];

- in  the speedproc() method, get rid of the duplicate reads/writes from/to the
  UDIDETCRx registers and of the extra variable used to store the transfer mode
  value after filtering,  use another method of determining master/slave drive,
  and cleanup useless parens;

- beautify cmdprintk() output here and there.

While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Sergei Shtylyov
688a87d145 sl82c105: DMA support code cleanup (take 4)
Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma().  Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well.  While at it, cleanup style in several places.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Sergei Shtylyov
e93df705af sl82c105: rework PIO support (take 2)
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly  simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Russell King
3603ab2b62 [ARM] mm 10: allow memory type to be specified with ioremap
__ioremap() took a set of page table flags (specifically the cacheable
and bufferable bits) to control the mapping type.  However, with
the advent of ARMv6, this is far too limited.

Replace the page table flags with a memory type index, so that the
desired attributes can be selected from the mem_type table.

Finally, to prevent silent miscompilation due to the differing
arguments, rename the __ioremap() and __ioremap_pfn() functions.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 20:59:27 +01:00
Matt Carlson
98efd8a6be [TG3]: Eliminate the TG3_FLAG_5701_REG_WRITE_BUG flag.
This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.

[ Comment tidy by Christoph Hellwig. -DaveM ]

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
2007-05-05 12:47:25 -07:00
Russell King
0af92befeb [ARM] mm 9: add additional device memory types
Add cached device type for ioremap_cached().  Group all device memory
types together, and ensure that they all have a "MT_DEVICE" prefix.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 20:28:16 +01:00
Michael Chan
5cf64b8a73 [TG3]: Eliminate the TG3_FLAG_GOT_SERDES_FLOWCTL flag.
This flag does not do anything useful.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 12:11:21 -07:00
Michael Chan
986e0aeb9a [TG3]: Remove reset during MAC address changes.
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.

This fixes 2 problems:

1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.

2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed. 

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 12:10:20 -07:00
Russell King
9ef7963503 [ARM] mm 8: define mem_types table L1 bit 4 to be for ARMv6
Change the memory types table to define the L1 descriptor bit 4 to
be in terms of the ARMv6 definition - execute never.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 20:03:35 +01:00
Gary Zambrano
a85feb8cfc [TG3]: WoL fixes.
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL.  This flag is now used consistently during ethtool WoL
setup and power setting changes.

Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:52:19 -07:00
Gary Zambrano
aaf84465fc [TG3]: Clear GPIO mask before storing.
The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.

Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:51:45 -07:00
Matt Carlson
989a9d239c [TG3]: Improve NVRAM sizing.
This patch changes the NVRAM sizing procedure so that the driver can
take advantage of devices with 1:1 NVRAM strapping configurations.  This
is useful in cases where the traditional NVRAM sizing method fails.  In
the event that the flash size cannot be determined, the largest known
NVRAM size is used.  The patch also removes support for 5755 NVRAM
devices that are not supported by Broadcom and adds explicit sizing for
this device.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:51:05 -07:00
Matt Carlson
c13e371385 [TG3]: Fix TSO bugs.
1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.

2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug.  This patch avoids the hanging condition by reducing the
DMA burst size.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:50:04 -07:00
Jiri Benc
64a327a702 [MAC80211]: Add maintainers entry for mac80211.
Add MAINTAINERS entry for mac80211.

Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:47:08 -07:00
Jiri Benc
e9f207f0ff [MAC80211]: Add debugfs attributes.
Export various mac80211 internal variables through debugfs.

Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:46:38 -07:00
Jiri Benc
f0706e828e [MAC80211]: Add mac80211 wireless stack.
Add mac80211, the IEEE 802.11 software MAC layer.

Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-05-05 11:45:53 -07:00
Jiri Benc
a9de8ce094 [MAC80211]: Add generic include/linux/ieee80211.h
Add generic IEEE 802.11 definitions.

Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:43:04 -07:00
Herbert Xu
cf130cb102 [NETLINK]: Remove references to process ID
People treating the *_pid fields in netlink as a process ID has caused
endless confusion over the years.  The fact that our own netlink.h
does this only adds to the confusion.

So here is a patch to change the comments to refer to it as the port
ID which hopefully will make it clear what the purpose of the fields
really is.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:42:03 -07:00
Heiko Carstens
af7cd373b0 [AF_IUCV]: Compile fix - adopt to skbuff changes.
From: Heiko Carstens <heiko.carstens@de.ibm.com>

  CC [M]  net/iucv/af_iucv.o
net/iucv/af_iucv.c: In function `iucv_fragment_skb':
net/iucv/af_iucv.c:984: error: structure has no member named `h'
net/iucv/af_iucv.c:985: error: structure has no member named `nh'
net/iucv/af_iucv.c:988: error: incompatible type for argument 1 of
			`skb_queue_tail'

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05 11:41:18 -07:00
Russell King
ad902cb9e2 [ARM] iop: add missing parens in macro
Fix:

 drivers/serial/8250.c:1837: warning: suggest parentheses around arithmetic in operand of |

due to a macro argument being used without required parenthesis.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 11:59:13 +01:00
Russell King
0058ca32c3 [ARM] mm 7: remove duplicated __ioremap() prototypes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 11:57:39 +01:00
David Brownell
fcf126d847 ARM: OMAP: fix OMAP1 mpuio suspend/resume oops
Fix oops in omap16xx mpuio suspend/resume code; field wasn't initialized

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:57:38 +01:00
David Brownell
11a78b7944 ARM: OMAP: MPUIO wake updates
GPIO and MPUIO wake updates:

 - Hook MPUIOs into the irq wakeup framework too.  This uses a platform
   device to update irq enables during system sleep states, instead of
   a sys_device, since the latter is no longer needed for such things.

 - Also forward enable/disable irq wake requests to the relevant GPIO
   controller, so the top level IRQ dispatcher can (eventually) handle
   these wakeup events automatically if more than one GPIO pin needs to
   be a wakeup event source.

 - Minor tweak to the 24xx non-wakeup gpio stuff: no need to check such
   read-only data under the spinlock.

This assumes (maybe wrongly?) that only 16xx can do GPIO wakeup; without
a 15xx I can't test such stuff.

Also this expects the top level IRQ dispatcher to properly handle requests
to enable/disable irq wake, which is currently known to be wrong:  omap1
saves the flags but ignores them, omap2 doesn't even save it.  (Wakeup
events are, wrongly, hardwired in the relevant mach-omapX/pm.c file ...)
So MPUIO irqs won't yet trigger system wakeup.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:57:17 +01:00
David Brownell
58781016c3 ARM: OMAP: speed up gpio irq handling
Speedup and shrink GPIO irq handling code, by using a pointer
that's available in the irq_chip structure instead of calling
the get_gpio_bank() function.  On OMAP1 this saves 44 words,
most of which were in IRQ critical path methods.  Hey, every
few instructions help.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:57:01 +01:00
Syed Mohammed Khasim
56a2564185 ARM: OMAP: plat-omap changes for 2430 SDP
This patch adds minimal OMAP2430 support to plat-omap files to
get the kernel booting on 2430SDP.

Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:56:45 +01:00
David Brownell
e5c56ed3c9 ARM: OMAP: gpio object shrinkage, cleanup
More GPIO/IRQ cleanup:

  - compile-time removal of much useless code
      * mpuio support on non-OMAP1.
      * 15xx/730/24xx gpio support on 1610
      * 15xx/730/16xx gpio support on 24xx
      * etc

  - remove all BUG() calls, which are always bad news ... replaced some
    with normal fault reports for that call, others with WARN_ON(1).

  - small mpuio bugfix:  add missing set_type() method

Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:56:28 +01:00
David Brownell
b9772a220a ARM: OMAP: /sys/kernel/debug/omap_gpio
Add some GPIO debug support:  /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.

Includes minor bugfixes:  recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:54:23 +01:00
Juha Yrjola
3ac4fa9929 ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon
Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:54:07 +01:00
Juha Yrjola
14f1c3bf51 ARM: OMAP: Enable 24xx GPIO autoidling
Enable 24xx GPIO autoidling

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:53:45 +01:00
Michael-Luke Jones
28bd3a0dcc [ARM] 4318/2: DSM-G600 Board Support
This patch adds support for the D-Link DSM-G600 Rev A.
This is an ARM XScale IXP4xx system relatively similar to
the NSLU2 and NAS-100D already supported by mainline. An
important difference is Gigabit Ethernet support using
the Via Velocity chipset.

This patch is the combined work of Michael Westerhof and
Alessandro Zummo, with contributions from Michael-Luke
Jones. This version addresses review comments from rmk
and Deepak Saxena.

Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Michael Westerhof <mwester@dls.net>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-05 10:06:49 +01:00
Linus Torvalds
62ea6d8021 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (46 commits)
  mmc-omap: Clean up omap set_ios and make MMC_POWER_ON work
  mmc-omap: Fix omap to use MMC_POWER_ON
  mmc-omap: add missing '\n'
  mmc: make tifm_sd_set_dma_data() static
  mmc: remove old card states
  mmc: support unsafe resume of cards
  mmc: separate out reading EXT_CSD
  mmc: break apart switch function
  MMC: Fix handling of low-voltage cards
  MMC: Consolidate voltage definitions
  mmc: add bus handler
  wbsd: check for data opcode earlier
  mmc: Separate out protocol ops
  mmc: Move core functions to subdir
  mmc: deprecate mmc bus topology
  mmc: remove card upon suspend
  mmc: allow suspended block driver to be removed
  mmc: Flush pending detects on host removal
  mmc: Move host and card drivers to subdirs
  mmc: Move queue functions to mmc_block
  ...
2007-05-04 21:44:34 -07:00
Linus Torvalds
fa24aa561a Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2: Force use of GFP_NOFS in ocfs2_write()
  ocfs2: fix sparse warnings in fs/ocfs2/cluster
  ocfs2: fix sparse warnings in fs/ocfs2/dlm
  ocfs2: fix sparse warnings in fs/ocfs2
  [PATCH] Copy i_flags to ocfs2 inode flags on write
  [PATCH] ocfs2: use __set_current_state()
  ocfs2: Wrap access of directory allocations with ip_alloc_sem.
  [PATCH] fs/ocfs2/: make 3 functions static
  ocfs2: Implement compat_ioctl()
2007-05-04 20:44:54 -07:00
Linus Torvalds
6cbf0c704d iomap: make the default iomap functions fail softer
We used to BUG_ON() for a badly mapped IO port, which is certainly
correct, but actually made it harder to debug the case where the ATA
drivers had incorrectly mapped a nonconnected ATA port.

So make badly mapped ports trigger a WARN_ON(), and throw the IO away
instead (and return all ones for reads).  For things like broken driver
initialization - which is the most likely cause anyway - that should
mean that the machine comes up and is usable (at least that was the case
for the ATA breakage that triggered this patch).

It tends to be a whole lot easier to do a "dmesg" on a working machine
than to try to capture logs off a dead one.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 20:44:23 -07:00
Jeff Layton
8426c39c12 [CIFS] Make sec=none force an anonymous mount
We had a customer report that attempting to make CIFS mount with a null
username (i.e. doing an anonymous mount) doesn't work. Looking through the
code, it looks like CIFS expects a NULL username from userspace in order
to trigger an anonymous mount. The mount.cifs code doesn't seem to ever
pass a null username to the kernel, however.

It looks also like the kernel can take a sec=none option, but it only seems
to look at it if the username is already NULL. This seems redundant and
effectively makes sec=none useless.

The following patch makes sec=none force an anonymous mount.

Signed-off-by: Steve French <sfrench@us.ibm.com>
2007-05-05 03:27:49 +00:00
Linus Torvalds
4d4700707c Merge git://git.linux-nfs.org/pub/linux/nfs-2.6
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (28 commits)
  NFS: Fix a compile glitch on 64-bit systems
  NFS: Clean up nfs_create_request comments
  spkm3: initialize hash
  spkm3: remove bad kfree, unnecessary export
  spkm3: fix spkm3's use of hmac
  NFS4: invalidate cached acl on setacl
  NFS: Fix directory caching problem - with test case and patch.
  NFS: Set meaningful value for fattr->time_start in readdirplus results.
  NFS: Added support to turn off the NFSv3 READDIRPLUS RPC.
  SUNRPC: RPC client should retry with different versions of rpcbind
  SUNRPC: remove old portmapper
  NFS: switch NFSROOT to use new rpcbind client
  SUNRPC: switch the RPC server to use the new rpcbind registration API
  SUNRPC: switch socket-based RPC transports to use rpcbind
  SUNRPC: introduce rpcbind: replacement for in-kernel portmapper
  SUNRPC: Eliminate side effects from rpc_malloc
  SUNRPC: RPC buffer size estimates are too large
  NLM: Shrink the maximum request size of NLM4 requests
  NFS: Use pgoff_t in structures and functions that pass page cache offsets
  NFS: Clean up nfs_sync_mapping_wait()
  ...
2007-05-04 19:55:11 -07:00
Linus Torvalds
7e20ef030d Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits)
  [SCTP]: Set assoc_id correctly during INIT collision.
  [SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv()
  [SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP.
  [SCTP]: Verify all destination ports in sctp_connectx.
  [XFRM] SPD info TLV aggregation
  [XFRM] SAD info TLV aggregationx
  [AF_RXRPC]: Sort out MTU handling.
  [AF_IUCV/IUCV] : Add missing section annotations
  [AF_IUCV]: Implementation of a skb backlog queue
  [NETLINK]: Remove bogus BUG_ON
  [IPV6]: Some cleanups in include/net/ipv6.h
  [TCP]: zero out rx_opt in tcp_disconnect()
  [BNX2]: Fix TSO problem with small MSS.
  [NET]: Rework dev_base via list_head (v3)
  [TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start
  [BNX2]: Update version and reldate.
  [BNX2]: Print bus information for PCIE devices.
  [BNX2]: Add 1-shot MSI handler for 5709.
  [BNX2]: Restructure PHY event handling.
  [BNX2]: Add indirect spinlock.
  ...
2007-05-04 19:36:58 -07:00
Linus Torvalds
a3d52136ee Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits)
  Input: gpio_keys - add support for switches (EV_SW)
  Input: cobalt_btns - convert to use polldev library
  Input: add skeleton for simple polled devices
  Input: update some documentation
  Input: wistron - fix typo in keymap for Acer TM610
  Input: add input_set_capability() helper
  Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs
  Input: i8042 - add Panasonic CF-29 to nomux list
  Input: lifebook - split into 2 devices
  Input: lifebook - add signature of Panasonic CF-29
  Input: lifebook - activate 6-byte protocol on select models
  Input: lifebook - work properly on Panasonic CF-18
  Input: cobalt buttons - separate device and driver registration
  Input: ati_remote - make button repeat sensitivity configurable
  Input: pxa27x - do not use deprecated SA_INTERRUPT flag
  Input: ucb1400 - make delays configurable
  Input: misc devices - switch to using input_dev->dev.parent
  Input: joysticks - switch to using input_dev->dev.parent
  Input: touchscreens - switch to using input_dev->dev.parent
  Input: mice - switch to using input_dev->dev.parent
  ...

Fixed up conflicts with core device model removal of "struct subsystem" manually.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 18:16:12 -07:00
Linus Torvalds
5b33991576 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  remove "struct subsystem" as it is no longer needed
  sysfs: printk format warning
  DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
  platform: reorder platform_device_del
  Driver core: fix show_uevent from taking up way too much stack
2007-05-04 18:04:48 -07:00
Linus Torvalds
89661adaae Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
  PCI: Free resource files in error path of pci_create_sysfs_dev_files()
  pci-quirks: disable MSI on RS400-200 and RS480
  PCI hotplug: Use menuconfig objects
  PCI: ZT5550 CPCI Hotplug driver fix
  PCI: rpaphp: Remove semaphores
  PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
  PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
  PCI: rpaphp: Document is_php_dn()
  PCI: rpaphp: Document find_php_slot()
  PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
  PCI: rpaphp: refactor tail call to rpaphp_register_slot()
  PCI: rpaphp: remove rpaphp_set_attention_status()
  PCI: rpaphp: remove print_slot_pci_funcs()
  PCI: rpaphp: Remove setup_pci_slot()
  PCI: rpaphp: remove a call that does nothing but a pointer lookup
  PCI: rpaphp: Remove another wrappered function
  PCI: rpaphp: Remve another call that is a wrapper
  PCI: rpaphp: remove a function that does nothing but wrap debug printks
  PCI: rpaphp: Remove un-needed goto
  PCI: rpaphp: Fix a memleak; slot->location string was never freed
  ...
2007-05-04 18:04:29 -07:00
Linus Torvalds
6adae5d9e6 Merge master.kernel.org:/pub/scm/linux/kernel/git/herbert/crypto-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] padlock: Remove pointless padlock module
  [CRYPTO] api: Add ablkcipher_request_set_tfm
  [CRYPTO] cryptd: Add software async crypto daemon
  [CRYPTO] api: Do not remove users unless new algorithm matches
  [CRYPTO] cryptomgr: Fix parsing of nested templates 
  [CRYPTO] api: Add async blkcipher type
  [CRYPTO] templates: Pass type/mask when creating instances
  [CRYPTO] tcrypt: Use async blkcipher interface
  [CRYPTO] api: Add async block cipher interface
  [CRYPTO] api: Proc functions should be marked as unused
2007-05-04 18:01:17 -07:00
Geert Uytterhoeven
253f04e78d ps3av: Use __func__ instead of __FUNCTION__
ps3av: Replace GNU extension `__FUNCTION__' by C99 `__func__'

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:09 -07:00
Geert Uytterhoeven
d778c9a400 ps3fb: Use __func__ instead of __FUNCTION__
ps3fb: Replace GNU extension `__FUNCTION__' by C99 `__func__'

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00
Masashi Kimoto
640729014e ps3: Make `ps3videomode -v 0 (auto mode) work again
ps3: Make `ps3videomode -v 0' (auto mode) work again

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00
Geert Uytterhoeven
fffe52e86b ps3av: misc updates
ps3av:
  - Move the definition of struct ps3av to ps3av.c, as it's locally used only.
  - Kill ps3av.sem, use the existing ps3av.mutex instead.
  - Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
    Its use is protected by a semaphore anyway.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00
Geert Uytterhoeven
bd685ac8e7 ps3fb: kill superfluous zero initializations
ps3fb: kill superfluous zero initializations

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00
Geert Uytterhoeven
5caf5db887 ps3av: thread updates
ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00
Geert Uytterhoeven
eca28743b7 ps3fb: atomic fixes
ps3fb: Use atomic_dec_if_positive() instead of bogus atomic_read()/atomic_dec()
combinations

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00
Geert Uytterhoeven
1c0c846119 ps3fb: thread updates
ps3fb: Replace the kernel_thread and the semaphore by a proper kthread, which
is simply woken up when the screen must be updated

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00
Geert Uytterhoeven
254f9c5cd2 Convert non-highmem kmap_atomic() to static inline function
Convert kmap_atomic() in the non-highmem case from a macro to a static
inline function, for better type-checking and the ability to pass void
pointers instead of struct page pointers.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-04 17:59:08 -07:00