[ Upstream commit a8d6d4992a ]
In the file mr75203.c we have a macro named POWER_DELAY_CYCLE_256,
the correct value should be 0x100. The register ip_tmr is expressed
in units of IP clk cycles, in accordance with the datasheet.
Typical power-up delays for Temperature Sensor are 256 cycles i.e. 0x100.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Arseny Demidov <a.demidov@yadro.com>
Link: https://lore.kernel.org/r/20211219102239.1112-1-a.demidov@yadro.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cdc5287aca upstream.
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7dc05684 upstream.
Tests with a real chip and a closer look into the datasheet reveals
that the local and remote critical alarm status bits are swapped for
MAX6680/MAX6681.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16ba51b5dc ]
Tests with a real chip and a closer look into the datasheet show that
MAX6654 does not support CRIT/THERM/OVERTEMP limits, so drop support
of the respective attributes for this chip.
Introduce LM90_HAVE_CRIT flag and use it to instantiate critical limit
attributes to solve the problem.
Cc: Josh Lehan <krellan@google.com>
Fixes: 229d495d81 ("hwmon: (lm90) Add max6654 support to lm90 driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8344f7693 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f347e249fc ]
A flag indicating extended temperature support makes it easier
to add support for additional chips with this functionality.
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55840b9eae ]
Commit b50aa49638 ("hwmon: (lm90) Prevent integer underflows of
temperature calculations") addressed a number of underflow situations
when writing temperature limits. However, it missed one situation, seen
when an attempt is made to set the hysteresis value to MAX_LONG and the
critical temperature limit is negative.
Use clamp_val() when setting the hysteresis temperature to ensure that
the provided value can never overflow or underflow.
Fixes: b50aa49638 ("hwmon: (lm90) Prevent integer underflows of temperature calculations")
Cc: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fce15c45d3 ]
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
Fixes: f90be42fb3 ("hwmon: (lm90) Refactor reading of config2 register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dbd3e6eaf3 upstream.
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2ca752055 upstream.
Before commit 86585c6197 ("hwmon: (pwm-fan) stop using legacy
PWM functions and some cleanups") pwm_apply_state() was called
unconditionally in pwm_fan_probe(). In this commit this direct
call was replaced by a call to __set_pwm(ct, MAX_PWM) which
however is a noop if ctx->pwm_value already matches the value to
set.
After probe the fan is supposed to run at full speed, and the
internal driver state suggests it does, but this isn't asserted
and depending on bootloader and pwm low-level driver, the fan
might just be off.
So drop setting pwm_value to MAX_PWM to ensure the check in
__set_pwm doesn't make it exit early and the fan goes on as
intended.
Cc: stable@vger.kernel.org
Fixes: 86585c6197 ("hwmon: (pwm-fan) stop using legacy PWM functions and some cleanups")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211130092212.17783-1-billy_tsai@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7931a7b0e ]
Maintaining this manually is error prone (there are currently only
five chips supported, not six); gcc can do it for us automatically.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 666c14906b ("hwmon: (pmbus/lm25066) Drop support for LM25063")
Link: https://lore.kernel.org/r/20210928092242.30036-5-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada61aa0b1 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888102740438 (size 8):
comm "27", pid 859, jiffies 4295031351 (age 143.992s)
hex dump (first 8 bytes):
68 77 6d 6f 6e 30 00 00 hwmon0..
backtrace:
[<00000000544b5996>] __kmalloc_track_caller+0x1a6/0x300
[<00000000df0d62b9>] kvasprintf+0xad/0x140
[<00000000d3d2a3da>] kvasprintf_const+0x62/0x190
[<000000005f8f0f29>] kobject_set_name_vargs+0x56/0x140
[<00000000b739e4b9>] dev_set_name+0xb0/0xe0
[<0000000095b69c25>] __hwmon_device_register+0xf19/0x1e50 [hwmon]
[<00000000a7e65b52>] hwmon_device_register_with_info+0xcb/0x110 [hwmon]
[<000000006f181e86>] devm_hwmon_device_register_with_info+0x85/0x100 [hwmon]
[<0000000081bdc567>] tmp421_probe+0x2d2/0x465 [tmp421]
[<00000000502cc3f8>] i2c_device_probe+0x4e1/0xbb0
[<00000000f90bda3b>] really_probe+0x285/0xc30
[<000000007eac7b77>] __driver_probe_device+0x35f/0x4f0
[<000000004953d43d>] driver_probe_device+0x4f/0x140
[<000000002ada2d41>] __device_attach_driver+0x24c/0x330
[<00000000b3977977>] bus_for_each_drv+0x15d/0x1e0
[<000000005bf2a8e3>] __device_attach+0x267/0x410
When device_register() returns an error, the name allocated in
dev_set_name() will be leaked, the put_device() should be used
instead of calling hwmon_dev_release() to give up the device
reference, then the name will be freed in kobject_cleanup().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: bab2243ce1 ("hwmon: Introduce hwmon_device_register_with_groups")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012112758.2681084-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ae59dc455a upstream.
With the exception of the lm5066i, all the devices handled by this
driver had been missing their offset ('b') coefficients for direct
format readings.
Cc: stable@vger.kernel.org
Fixes: 58615a94f6 ("hwmon: (pmbus/lm25066) Add support for LM25056")
Fixes: e53e6497fc ("hwmon: (pmbus/lm25066) Refactor device specific coefficients")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-3-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-2-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multipline alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-1-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add missed attribute for reading POUT from page 1.
It is supported by device, but has been missed in initial commit.
Fixes: 2c6fcbb211 ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927070740.2149290-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Tested:
Witherspoon before: 3148. Witherspoon after: 3148.
Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The P10 (temp sensor version 0x10) doesn't do the same VRM status
reporting that was used on P9. It just reports the temperature, so
drop the check for VRM fru type in the sysfs show function, and don't
set the name to "alarm".
Fixes: db4919ec86 ("hwmon: (occ) Add new temperature sensor type")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210929153604.14968-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of devm_clk_get should in general be propagated to
upper layer. In this case the clk is optional, use the appropriate
wrapper instead of interpreting all errors as "The optional clk is not
available".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210923201113.398932-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Old code produces -24999 for 0b1110011100000000 input in standard format due to
always rounding up rather than "away from zero".
Use the common macro for division, unify and simplify the conversion code along
the way.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-3-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For both local and remote sensors all the supported ICs can report an
"undervoltage lockout" condition which means the conversion wasn't
properly performed due to insufficient power supply voltage and so the
measurement results can't be trusted.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-2-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function i2c_smbus_read_byte_data() can return a negative error number
instead of the data read if I2C transaction failed for whatever reason.
Lack of error checking can lead to serious issues on production
hardware, e.g. errors treated as temperatures produce spurious critical
temperature-crossed-threshold errors in BMC logs for OCP server
hardware. The patch was tested with Mellanox OCP Mezzanine card
emulating TMP421 protocol for temperature sensing which sometimes leads
to I2C protocol error during early boot up stage.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-1-fercerpav@gmail.com
[groeck: dropped unnecessary line breaks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fan speed minimum can be enforced from sysfs. For example, setting
current fan speed to 20 is used to enforce fan speed to be at 100%
speed, 19 - to be not below 90% speed, etcetera. This feature provides
ability to limit fan speed according to some system wise
considerations, like absence of some replaceable units or high system
ambient temperature.
Request for changing fan minimum speed is configuration request and can
be set only through 'sysfs' write procedure. In this situation value of
argument 'state' is above nominal fan speed maximum.
Return non-zero code in this case to avoid
thermal_cooling_device_stats_update() call, because in this case
statistics update violates thermal statistics table range.
The issues is observed in case kernel is configured with option
CONFIG_THERMAL_STATISTICS.
Here is the trace from KASAN:
[ 159.506659] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.516016] Read of size 4 at addr ffff888116163840 by task hw-management.s/7444
[ 159.545625] Call Trace:
[ 159.548366] dump_stack+0x92/0xc1
[ 159.552084] ? thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.635869] thermal_zone_device_update+0x345/0x780
[ 159.688711] thermal_zone_device_set_mode+0x7d/0xc0
[ 159.694174] mlxsw_thermal_modules_init+0x48f/0x590 [mlxsw_core]
[ 159.700972] ? mlxsw_thermal_set_cur_state+0x5a0/0x5a0 [mlxsw_core]
[ 159.731827] mlxsw_thermal_init+0x763/0x880 [mlxsw_core]
[ 160.070233] RIP: 0033:0x7fd995909970
[ 160.074239] Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ..
[ 160.095242] RSP: 002b:00007fff54f5d938 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 160.103722] RAX: ffffffffffffffda RBX: 0000000000000013 RCX: 00007fd995909970
[ 160.111710] RDX: 0000000000000013 RSI: 0000000001906008 RDI: 0000000000000001
[ 160.119699] RBP: 0000000001906008 R08: 00007fd995bc9760 R09: 00007fd996210700
[ 160.127687] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000013
[ 160.135673] R13: 0000000000000001 R14: 00007fd995bc8600 R15: 0000000000000013
[ 160.143671]
[ 160.145338] Allocated by task 2924:
[ 160.149242] kasan_save_stack+0x19/0x40
[ 160.153541] __kasan_kmalloc+0x7f/0xa0
[ 160.157743] __kmalloc+0x1a2/0x2b0
[ 160.161552] thermal_cooling_device_setup_sysfs+0xf9/0x1a0
[ 160.167687] __thermal_cooling_device_register+0x1b5/0x500
[ 160.173833] devm_thermal_of_cooling_device_register+0x60/0xa0
[ 160.180356] mlxreg_fan_probe+0x474/0x5e0 [mlxreg_fan]
[ 160.248140]
[ 160.249807] The buggy address belongs to the object at ffff888116163400
[ 160.249807] which belongs to the cache kmalloc-1k of size 1024
[ 160.263814] The buggy address is located 64 bytes to the right of
[ 160.263814] 1024-byte region [ffff888116163400, ffff888116163800)
[ 160.277536] The buggy address belongs to the page:
[ 160.282898] page:0000000012275840 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888116167000 pfn:0x116160
[ 160.294872] head:0000000012275840 order:3 compound_mapcount:0 compound_pincount:0
[ 160.303251] flags: 0x200000000010200(slab|head|node=0|zone=2)
[ 160.309694] raw: 0200000000010200 ffffea00046f7208 ffffea0004928208 ffff88810004dbc0
[ 160.318367] raw: ffff888116167000 00000000000a0006 00000001ffffffff 0000000000000000
[ 160.327033] page dumped because: kasan: bad access detected
[ 160.333270]
[ 160.334937] Memory state around the buggy address:
[ 160.356469] >ffff888116163800: fc ..
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210916183151.869427-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit id "b00647c46c9d7f6ee1ff6aaf335906101755e614",
adds reporting current and voltage to k10temp.c
The commit id "0a4e668b5d52eed8026f5d717196b02b55fb2dc6",
removed reporting current and voltage from k10temp.c
The curr and in(voltage) entries are not removed from
"k10temp_info" structure. Removing those residue entries.
while at it, update k10temp driver documentation
Signed-off-by: suma hegde <suma.hegde@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210902174155.7365-2-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
The new macro is an unsigned long. The code dealing with it is
considering as an unsigned long also.
Link: https://lkml.kernel.org/r/20210816114732.1834145-7-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the devm_hwmon_device_register_with_info API and remove code that
deals with the standard sensor attributes.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210826024121.15665-4-chris.packham@alliedtelesis.co.nz
[groeck: Fixed alignment issues]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation for the changes that follow fix up some existing style
issues.
Specifically:
- add blank line between variable declaration and code
- use strscpy instead of strlcpy
- remove unnecessary braces
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210826024121.15665-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Yellow carp matches same behavior as green sardine and other Zen3
products, but have different CCD offsets.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20210827201527.24454-3-mario.limonciello@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the existing assumptions made do not scale properly
to new silicon in upcoming changes. This commit should cause
no functional changes to existing silicon.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20210827201527.24454-2-mario.limonciello@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tdie is an offset calculation that should only be shown when temp_offset
is actually put into a table. This is useless to show for all CPU/APU.
Show it only when necessary.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These follow the rest of the existing codepaths for families
17h and 19h.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drop #ifdef DEBUG and use ktime_us_delta()
for improved precision.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210814190516.26718-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Mark function i8k_get_fan_nominal_speed() as __init since
it is only used in code also marked as __init.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210814143637.11922-5-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both the config and the DMI tables never change and
are only used during module init for setting up
the device data struct.
Mark all of them as const and __initconst for a
smaller runtime memory footprint.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210814143637.11922-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
BPD-RS600 modules running firmware v5.70 misreport the MFR_PIN_MAX.
The indicate a maximum of 1640W instead of 700W. Detect the invalid
reading and return a sensible value instead.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210812014000.26293-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In the initial implementation a number of PMBUS_x_WARN_LIMITs were
mapped to MFR fields. This was incorrect as these MFR limits reflect the
rated limit as opposed to a limit which will generate warning. Instead
return -ENXIO like we were already doing for other WARN_LIMITs.
Subsequently these rated limits have been exposed generically as new
fields in the sysfs ABI so the values are still available.
Fixes: 15b2703e5e ("hwmon: (pmbus) Add driver for BluTek BPA-RS600")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210812014000.26293-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HW has some predefined points where it will associate a PWM value.
However some users might want to better set these points to their
usecases. This patch exposes these points as pwm auto_points:
* pwm1_auto_point1_temp_hyst: temperature threshold below which PWM should
be 0%;
* pwm1_auto_point1_temp: temperature threshold above which PWM should be
25%;
* pwm1_auto_point2_temp_hyst: temperature threshold below which PWM should
be 25%;
* pwm1_auto_point2_temp: temperature threshold above which PWM should be
50%;
* pwm1_auto_point3_temp_hyst: temperature threshold below which PWM should
be 50%;
* pwm1_auto_point3_temp: temperature threshold above which PWM should be
75%;
* pwm1_auto_point4_temp_hyst: temperature threshold below which PWM should
be 75%;
* pwm1_auto_point4_temp: temperature threshold above which PWM should be
100%;
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210811114853.159298-4-nuno.sa@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The core will now start out of reset at boot as soon as clocking is
available. Hence, by the time we unmask the interrupts we already might
have some of them set. Thus, it's important to handle them in the
natural order the core generates them. Otherwise, we could process
'ADI_IRQ_SRC_PWM_CHANGED' before 'ADI_IRQ_SRC_TEMP_INCREASE' and
erroneously set 'update_tacho_params' to true.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210811114853.159298-3-nuno.sa@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The core will only work if it's clock is enabled. This patch is a
minor enhancement to make sure that's the case.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210811114853.159298-2-nuno.sa@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When doing a PMBus write for the LED control on the IBM Common Form
Factor Power Supplies (ibm-cffps), the DAh command requires that bit 7
be low and bit 6 be high in order to indicate that you are truly
attempting to do a write.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210806225131.1808759-1-bjwyman@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C devices should match on the proper compatible string.
This is already used in one device tree in the kernel (MIPS)
so let's add the matches.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210729230543.2853485-2-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-14-bigeasy@linutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This allows manual PWM control without the BIOS fighting back on Dell
Precision 7510. Meanwhile at it, also sort alphabetically the entries
of the i8k_whitelist_fan_control struct.
Signed-off-by: Carlos Alberto Lopez Perez <clopez@igalia.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210802131538.8660-1-clopez@igalia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There are up to three fans, but the detection omits the 3rd one.
Fix that by using DELL_SMM_NO_FANS.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Fixes: 747bc8b063 (hwmon: (dell-smm) Detect fan with index=2)
Link: https://lore.kernel.org/r/20210728221557.8891-7-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
