Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This achieves two goals:
1) Get rid of davinci_uart_v2p() and davinci_uart_p2v() which were the
last users of PLAT_PHYS_OFFSET.
2) Remove the probing of the M bit in the CP15 control reg and make
the access to the .data variables completely position independent.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
This is the first step to remove PLAT_PHYS_OFFSET usage from the debug
UART code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use. Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.
This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Use kzalloc rather than kmalloc followed by memset with 0
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
The semantic patch that makes this output is available
in scripts/coccinelle/api/alloc/kzalloc-simple.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Davinci platforms may define a default queue for each channel
controller. If one is not defined, the default queue is set to EVENTQ_1.
However, there's no way to distinguish between an unset default queue to
one that is set to EVENTQ_0, as EVENTQ_0 = 0.
Explicitly specify the default queue for all channel controllers on all
Davinci platforms to EVENTQ_1, and don't overwrite it in the EDMA probe
function.
One exception is the DA850 board, for which EVENTQ_1 is not a valid
option for its second channel controller. Use EVENTQ_0 instead for that
channel controller.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The wl1271 daughter card for AM18x EVMs is a combo wireless connectivity
add-on card, based on the LS Research TiWi module with Texas
Instruments' wl1271 solution.
It is a 4-wire, 1.8V, embedded SDIO WLAN device with an external IRQ
line and is power-controlled by a GPIO-based fixed regulator.
Add support for the WLAN capabilities of this expansion board.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some devices connected to the MMC bus are power controlled by external
means. For instance, an SDIO device may be powered down/up by an
external gpio line.
In order to avoid toggling power from within the MMC host driver, add a
set_power callback function, which will be called by set_ios upon
powering down/up.
Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Chris Ball <cjb@laptop.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The wl1271 daughter board makes use of a few GPIOs:
GPIO6_9 is used for powering down/up the WLAN functionality.
GPIO6_10 is used as an input IRQ line from the WLAN chip.
Add the required pinmux configuration for these GPIOs.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
AM18x has two MMC slots. Add the required pinmux configuration for the
second slot.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Recall the recently added prefix requirements:
* "NAND_" for flags in nand.h, used in nand_chip.options
* "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
or in nand_bbt_descr.options
Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.
Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch works with the following three flags from two headers (nand.h
and bbm.h):
(1) NAND_USE_FLASH_BBT (nand.h)
(2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
(3) NAND_BBT_NO_OOB (bbm.h)
These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.
This patch accomplishes the following:
* eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
* move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h
It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.
I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The TNET variant of DaVinci compiles some code that it shares
with other DaVinci variants, however it has a V6 CPU rather than
an ARM926T, thus the hardcoded call to arm926_flush_kern_cache_all()
in sleep.S will obviously fail, and we need to build with the
v6_flush_kern_cache_all() call instead. This was triggered by
manually altering the DaVinci config to build the TNET version.
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org
MDSTAT.STATE occupies bits 0..5 according to all available documentation, so fix
the #define MDSTAT_STATE_MASK at last. Using the wrong value seems to have been
harmless though...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
DA850/OMAP-L138 EMAC driver uses random mac address instead of
a fixed one because the mac address is not stuffed into EMAC
platform data.
This patch provides a function which reads the mac address
stored in SPI flash (registered as MTD device) and populates the
EMAC platform data. The function which reads the mac address is
registered as a callback which gets called upon addition of MTD
device.
NOTE: In case the MAC address stored in SPI flash is erased, follow
the instructions at [1] to restore it.
[1] http://processors.wiki.ti.com/index.php/GSG:_OMAP-L138_DVEVM_Additional_Procedures#Restoring_MAC_address_on_SPI_Flash
Modifications in v2:
Guarded registering the mtd_notifier only when MTD is enabled.
Earlier this was handled using mtd_has_partitions() call, but
this has been removed in Linux v3.0.
Modifications in v3:
a. Guarded da850_evm_m25p80_notify_add() function and
da850evm_spi_notifier structure with CONFIG_MTD macros.
b. Renamed da850_evm_register_mtd_user() function to
da850_evm_setup_mac_addr() and removed the struct mtd_notifier
argument to this function.
c. Passed the da850evm_spi_notifier structure to register_mtd_user()
function.
Modifications in v4:
Moved the da850_evm_setup_mac_addr() function within the first
CONFIG_MTD ifdef construct.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci TNET
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many of the gpio_to_irq implementations use the gpiolib version of this
function. Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish. Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Video input mux settings for tvp7002 and imager inputs were swapped.
Comment was correct.
Tested on EVM with tvp7002 input.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: stable@kernel.org
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 7416401 ("arm: davinci: Fix fallout from generic irq chip
conversion") introduced a bug, causing low level interrupt handlers to
get a bogus irq number as an argument. The gpio irq handler falsely
assumes that the handler data is the irq base number and that is no
longer true.
Set the irq handler data to be a pointer to the corresponding gpio
controller. The chained irq handler can then use it to extract both the
irq base number and the gpio registers structure.
Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Thomas Gleixner <tglx@linutronix.de>
[nsekhar@ti.com: renamed "ctl" to "d", simplified indexing logic for chips and
took care of odd bank handling in irq handler]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for SATA controller on the
DA850/OMAP-L138/AM18x devices.
The patch adds the necessary clocks, platform
resources and a routine to initialize the SATA
controller.
The PHY configuration in this patch is
courtesy the work done by Zegeye Alemu,
Swaminathan and Mansoor Ahamed from TI.
While testing this patch, enable port multiplier
support iff you are actually using one. The
reasons of this behaviour are discussed
here: http://patchwork.ozlabs.org/patch/78163/
ChangeLog:
v3:
Removed fields which were being initialized
to zero in PHY configuration. Moved SATA base
address definition to the top of the file to
make it inline with what is done for the rest
of the modules.
v2:
Addressed comments from Sergei. Removed unnecessary
braces and removed unnecessary else after goto.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some DaVinci modules like the SATA on DA850
need forced module state transitions.
Define a "force" flag which can be passed to
the PSC config function to enable it to make
forced transitions.
Forced transitions shouldn't normally be attempted,
unless the TRM explicitly specifies its usage.
ChangeLog:
v2:
Modified to take care of the fact that
davinci_psc_config() now takes the flags
directly.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enabling or disabling a PSC can take certain
modifiers like "disable with reset", "force
enable/disable" and "enable/disable with local
reset" apart from the regular clock gating
functionality.
Pass a flags argument to davinci_psc_config()
so these variations can be supported there.
At this time only "disable with reset" is
supported, but other functionality will be
added in subsequent patches.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch allows setting the input clock frequency of the SoC from
the board specific code using the davinci_set_refclk_rate function.
Suggested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The DM6467 and DM6467T EVMs use different reference clock
frequencies. This difference is currently supported by having
the SoC code call a public board routine which sets up the reference
clock frequency. This does not scale as more boards are added.
Instead, use the clk_set_rate() API to setup the reference clock
frequency to a different value from the board file.
Suggested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Platforms provide an empty irq_prio_table macro, and as nothing uses
this macro, it can simply be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the PCM device structures used in devices.c
and devices-da8xx.c static as they are used only
in the respective files.
This was found when trying to build a single image
for DaVinci and DA8x devices using runtime P2V support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The code which does the chained handler setup was overwriting
chip_data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Holger Hans Peter Freyther <holger@freyther.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Move the definition of DM64XX_VDD3P3V_PWDN from hardware.h
to devices.c since it is used only there.
This also helps rid hardware.h of platform private stuff.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Rather than each platform providing its own function to adjust the
zone sizes, use the new ARM_DMA_ZONE_SIZE definition to perform this
adjustment. This ensures that the actual DMA zone size and the
ISA_DMA_THRESHOLD/MAX_DMA_ADDRESS definitions are consistent with
each other, and moves this complexity out of the platform code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The values of ISA_DMA_THRESHOLD and MAX_DMA_ADDRESS are related; one is
the physical/bus address, the other is the virtual address. Both need
to be kept in step, so rather than having platforms define both, allow
them to define a single macro which sets both of these macros
appropraitely.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Simple conversion which simply uses the fact that the second irq chip
base address has offset 0x04 to the first one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-and-Tested-by: Kevin Hilman <khilman@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Move DA8XX_MMCSD0_BASE, DA8XX_LCD_CNTRL_BASE, and DA8XX_DDR2_CTL_BASE from
<mach/da8xx.h> to devices-da8xx.c as the latter file is the only place where
these macros are used.
While at it, restore sorting the base address macros by address value in
devices-da8xx.c...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Commit 044ca01521 (davinci: da850/omap-l138: add
support for SoC suspend) introduced DA8XX_PLL1_BASE despite PLL1 exists only on
DA850/OMAP-L138 and da850.c even already #define'd DA850_PLL1_BASE. Kill the
duplicate macro, renaming an existing reference to it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
DA8XX_GPIO_BASE is #define'd in both <mach/da8xx.h> and devices-da8xx.c;
moreover, it's not even used in the latter file...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
With dynamic debug having gained the capability to report debug messages
also during the boot process, it offers a far superior interface for
debug messages than the custom cpufreq infrastructure. As a first step,
remove the old cpufreq_debug_printk() function and replace it with a call
to the generic pr_debug() function.
How can dynamic debug be used on cpufreq? You need a kernel which has
CONFIG_DYNAMIC_DEBUG enabled.
To enabled debugging during runtime, mount debugfs and
$ echo -n 'module cpufreq +p' > /sys/kernel/debug/dynamic_debug/control
for debugging the complete "cpufreq" module. To achieve the same goal during
boot, append
ddebug_query="module cpufreq +p"
as a boot parameter to the kernel of your choice.
For more detailled instructions, please see
Documentation/dynamic-debug-howto.txt
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: (47 commits)
CLKDEV: Fix clkdev return value for NULL clk case
ARM: 6891/1: prevent heap corruption in OABI semtimedop
ARM: kprobes: Tidy-up kprobes-decode.c
ARM: kprobes: Add emulation of hint instructions like NOP and WFI
ARM: kprobes: Add emulation of SBFX, UBFX, BFI and BFC instructions
ARM: kprobes: Add emulation of MOVW and MOVT instructions
ARM: kprobes: Reject probing of undefined data processing instructions
ARM: kprobes: Remove redundant code in space_1111
ARM: kprobes: Fix emulation of PLD instructions
ARM: kprobes: Reject probing of SETEND instructions
ARM: kprobes: Consolidate stub decoding functions
ARM: kprobes: Reject probing of all coprocessor instructions
ARM: kprobes: Fix emulation of USAD8 instructions
ARM: kprobes: Fix emulation of SMUAD, SMUSD and SMMUL instructions
ARM: kprobes: Fix emulation of SXTB16, SXTB, SXTH, UXTB16, UXTB and UXTH instructions
ARM: kprobes: Reject probing of undefined media instructions
ARM: kprobes: Add emulation of RBIT instruction
ARM: kprobes: Reject probing of LDRB instructions which load PC
ARM: kprobes: Fix emulation of LDRD and STRD instructions
ARM: kprobes: Reject probing of LDR/STR instructions which update PC unpredictably
...
Several Davinci platforms select the I2C EEPROM support, but don't
select I2C support. This causes I2C EEPROM support to be built into
the kernel, but I2C support may not be configured to be built in.
This leads to linker errors due to missing I2C symbols.
Arrange for I2C to be selected whenever EEPROM_AT24 is selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 54ce6883d2 (davinci: da8xx: add spi
resources and registration routine) wrongly assumed that SPI1 is mapped at
the same address on DA830/OMAP-L137 and DA850/OMAP-L138; actually, the base
address was valid only for the latter SoC. Teach the code to pass the correct
SPI1 memory resource for both SoCs...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Current board configurations involving the MityDSP-L138 and MityARM-1808
only have one attached PHY, but it's address may not be the same. Default
the behavior to auto-probe for the PHY and use the first one found.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
For the MityDSP-L138/MityARM-1808 SOMS, the NAND controller id (which needs
to correspond to the chipselect, and is used for controlling the HW ECC
computation) is not correct. Fix it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fixup davinci UART low-level debug code for new ARM generic p2v changes.
Based on OMAP changes by Tony Lindgren
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Make use of the new functionality which ensures that irq_set_type is
called with the chip masked. Unmask is only done when the interrupt is
not disabled.
Retrieve the trigger type from irq_data in unmask
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
The MUSB driver doesn't see its platform device on DM644x EVM board anymore
since commit 73b089b052 (usb: musb: split davinci
to its own platform_driver) because the new probe is called as subsys_initcall()
now, and the device is registered later than that by the board code. Move the
registration to davinci_evm_init() -- it's safe to do so because the MUSB core
device still gets initialized as fs_initcall() -- which is late enough for the
I2C GPIO expander (which controls VBUS) to be initialized.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds definitions for spi devices on the tnetv107x evm platform.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SSP configuration and pin muxing info for tnetv107x
evm boards.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds an SSP platform device definition for the tnetv107x soc family.
The clock lookup entry has also been updated to match.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
DMAX is an internal name for the module which is
known as PRUSS in TI public documentation. This patch just
gets the code in sync with TI documentation.
Signed-off-by: Subhasish Ghosh <subhasish@mistralsolutions.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 75e2ea643f (davinci: DA850/OMAP-L138 EVM
expander setup and UI card detection) introduced a useless variable: it's
always set to 1 before it's checked in da850_evm_setup_nor_nand()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA830/OMAP-L137/AM17x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da830evm_spi0_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da830evm_init_spi0 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA850/OMAP-L138/AM18x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da850_evm_spi1_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da850evm_init_spi1 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds support for accessing the on board SPI NOR FLASH
device for MityDSP-L138 and MityARM-1808 SoMs.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add IO resource structures, platform data, and a registration
routine in order to support spi device on DA850/OMAP-L138/AM18x
and DA830/OMAP-L137/AM17x platforms.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add spi clock information for da850.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The spi driver name called out for the da830 spi clock list is not correct,
fix it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Extract magic numbers from DMA resource initializers to #defines.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The DA830_edma_ch enum set is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix below section mismatch warning:
WARNING: vmlinux.o(.data+0x673c): Section mismatch in reference from the variable davinci_driver to the function .init.text:davinci_cpu_init()
The variable davinci_driver references
the function __init davinci_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 6d803ba736 (ARM: 6483/1: arm & sh:
factorised duplicated clkdev.c) caused the following warnings:
In file included from /home/headless/src/kernel.org/linux-davinci/arch/arm/
include/asm/clkdev.h:17,
from include/linux/clkdev.h:15,
from arch/arm/mach-davinci/clock.h:71,
from arch/arm/mach-davinci/common.c:22:
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: `struct clk' declared
inside parameter list
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/mach-davinci/include/mach/clkdev.h:9: warning: `struct clk' declared
inside parameter list
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For DMA operation, the davinci spi driver needs an event queue number.
Currently, this number is passed as a IORESOURCE_DMA. This is not
correct, as the event queue is not a DMA channel. Pass the event queue
via the platform data structure instead.
On dm355 and dm365, move the eventq assignment for spi0 out of resources
array and into platform data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850 uart pinmux arrays are not used. Remove them.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mmcsd0_pins pinmux array contains pins that are specific to the
da850 evm board (the write protect and card detect GPIO pins). Move
the array to the board file.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mcasp_pins pinmux array is specific to the da850_evm, and is
not generic. Move the array to the board file, make it static initdata,
and rename it accordingly.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_emif25_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_cpgmac_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For the MityDSP-L138/MityARM-1808 SoMs, the speed grade can be determined
from the part number string read from the factory configuration block on
the on-board I2C PROM. Configure the maximum CPU speed based on this
information.
This patch was tested using a MityDSP-L138 and MityARM-1808 at various
speedgrades. Also, for code coverage, a bogus configuration was tested
as well as a configuration having an unknown part number.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
From: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
The JTAG variant code for Rev-2.0 silicon of the OMAP-L138 has changed.
In addition, the variant code for the AM-1808 SoC appears to match
the Rev-2.0 code for the OMAP-L138. Add an additional entry to support
these chips.
This patch is originally from a patch on the arago project, here:
http://arago-project.org/git/projects/?p=linux-omapl1.git;a=commit;h=6157618435e313a444cdf059702bd34036a6e2b7
Further information related to the need for this patch can be located at
http://e2e.ti.com/support/embedded/f/354/p/67290/248486.aspxhttp://linux.davincidsp.com/pipermail/davinci-linux-open-source/2010-November/021224.html
This patch was tested using an AM-1808 SoC on a MityARM-1808 SoM card. It
was also tested using a Rev 1.0 silicon OMAP-L138 on a MityDSP-L138F card.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Reported-by: Nicolas Luna <luna.id@gmail.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds USB1.1 support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds USB1.1 and USB2.0 clocks for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds MMC/SD support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch defines Pin Mux configuration to enable MMC/SD
and USB-OHCI on the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds EDMA support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds EMAC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch fix a bug in the register indexing for GPIOs numbers > 31
to get the relevant hardware registers of tnetv107x to control the GPIOs.
In the structure tnetv107x_gpio_regs:
struct tnetv107x_gpio_regs {
u32 idver;
u32 data_in[3];
u32 data_out[3];
u32 direction[3];
u32 enable[3];
};
The GPIO hardware register addresses of tnetv107x are stored.
The chip implements 3 registers of each entity to serve 96 GPIOs,
each register provides a subset of 32 GPIOs.
The driver provides these macros: gpio_reg_set_bit, gpio_reg_get_bit
and gpio_reg_clear_bit.
The bug implied the use of macros to access the relevant hardware
register e.g. the driver code used the macro like this:
'gpio_reg_clear_bit(®->data_out, gpio)'
But it has to be used like this:
'gpio_reg_clear_bit(reg->data_out, gpio)'.
The different results are shown here:
- ®->data_out + 1 (it will add the full array size of data_out i.e. 12 bytes)
- reg->data_out + 1 (it will increment only the size of data_out i.e. only 4 bytes)
Acked-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Hirosh Dabui <hirosh.dabui@snom.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
After the multi-component commit f0fba2ad (ASoC: multi-component - ASoC
Multi-Component Support) for ASoC, we need to register the platform
device for davinci-pcm-audio.
This patch and patch at [1] are required for audio to work on
DA850/OMAP-L138.
[1] https://patchwork.kernel.org/patch/495211/
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* 'for-grant' of git://arago-project.org/git/projects/linux-davinci into spi/next
spi: davinci: fix checkpatch errors
spi: davinci: whitespace cleanup
spi: davinci: remove unused variable 'pdata'
spi: davinci: set chip-select mode in SPIDEF only once
spi: davinci: enable both activation and deactivation of chip-selects
spi: davinci: remove unnecessary data transmit on CS disable
spi: davinci: enable GPIO lines to be used as chip selects
spi: davinci: simplify prescalar calculation
spi: davinci: remove 'wait_enable' platform data member
spi: davinci: make chip-slect specific parameters really chip-select specific
spi: davinci: consolidate setup of SPIFMTn in one function
spi: davinci: setup chip-select timers values only if timer enabled
spi: davinci: add support for wait enable timeouts
spi: davinci: remove unused members of davinci_spi_slave
spi: davinci: eliminate the single member structure davinci_spi_slave
spi: davinci: eliminate unnecessary update of davinci_spi->count
spi: davinci: simplify calculation of edma acount value
spi: davinci: check for NULL buffer pointer before using it
spi: davinci: remove unnecessary disable of SPI
spi: davinci: remove unnecessary 'count' variable in driver private data
spi: davinci: remove unnecessary completion variable initialization
spi: davinci: remove non-useful interrupt mode support
spi: davinci: simplify poll mode transfers
spi: davinci: add support for interrupt mode
spi: davinci: configure the invariable bits in spipc0 only once
spi: davinci: remove unnecessary function davinci_spi_bufs_prep()
spi: davinci: remove unnecessary call to davinci_spi_setup_transfer()
spi: davinci: do not store DMA channel information per chip select
spi: davinci: always start transmit DMA
spi: davinci: do not use temporary buffer if no transmit data provided
spi: davinci: always start receive DMA
spi: davinci: use edma_write_slot() to setup EDMA PaRAM slot
spi: davinci: fix DMA event generation stoppage
spi: davinci: fix EDMA CC errors at end of transfers
spi: davinci: handle DMA completion errors correctly
spi: davinci: remove usage of additional completion variables for DMA
spi: davinci: let DMA operation be specified on per-device basis
spi: davinci: remove non-useful "clk_internal" platform data
spi: davinci: enable and power-up SPI only when required
spi: davinci: setup the driver owner
spi: davinci: add additional comments
spi: davinci: add EF Johnson Technologies copyright
spi: davinci: removed unused #defines
spi: davinci: remove unnecessary typecast
spi: davinci: do not treat Tx interrupt being set as error
spi: davinci: do not allocate DMA channels during SPI device setup
spi: davinci: remove unnecessary private data member 'region_size'
spi: davinci: shorten variable names
spi: davinci: kconfig: add manufacturer name to prompt string
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apart from the regular AM18x/DA850/OMAP-L138 SoC operating
at 300MHz, these SoCs have variants that can operate at a
maximum of 456MHz. Variants at 408Mhz and 375 Mhz are available
as well.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
The EVM hardware for all these variants is the same (except
for the actual SoC populated).
U-Boot on the EVM sets up ATAG_REVISION to inform the OS
regarding the speed grade supported by the silicon. We use
this information to pass on the speed grade information to
the SoC code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
AM18x/DA850/OMAP-L138 SoCs have variants that can operate
at a maximum of 456 MHz at 1.3V operating point. Also the
1.2V operating point has a variant that can support a maximum
of 375 MHz.
This patch adds three new OPPs (456 MHz, 408 MHz and 372 MHz)
to the list of DA850 OPPs.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
Because of this, we depend on the maximum speed grade information
to be provided to us in some board specific way. The board informs
the maximum speed grade information by setting the da850_max_speed
variable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use the mach-davinci/Kconfig to enable gpio-keys-polled as default when
da850-evm machine is enabled.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: "Nori, Sekhar" <nsekhar@ti.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a pca953x platform device for the tca6416 found on the evm
baseboard. The tca6416 is a GPIO expander, also found on the UI board at a
separate I2C address. The pins of the baseboard IO expander are connected to
software reset, deep sleep enable, test points, a push button, DIP switches and
LEDs.
Add support for the push button, DIP switches and LEDs and test points (as
free GPIOs). The reset and deep sleep enable connections are reserved by the
setup routine so that userspace can't toggle those lines.
The existing tca6416-keypad driver was not employed because there was no
apararent way to register the LEDs connected to gpio's on the tca6416 while
simultaneously registering the tca6416-keypad instance.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The setup and teardown methods of the UI expander reference the SEL_{A,B,C}
pins by 'magic number' in each function. This uses the common enum for their offsets
in the expander setup and teardown functions.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Victor Rodriguez <vm.rod25@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds EV_KEYs for each of the 8 pushbuttons on the UI board via a
gpio-key device.
The expander is a tca6416; it controls the SEL_{A,B,C} lines which enable and
disable the peripherals found on the UI board in addition to the 8 pushbuttons
mentioned above. The reason the existing tca6416-keypad driver is not employed
is because there was no aparent way to keep the gpio lines used as
SEL_{A,B,C} registered while simultaneously registering the pushbuttons as a
tca6416-keypad instance.
Some experimentation with the polling interval was performed; we were searching
for the largest polling interval that did not affect the feel of the
responsiveness of the buttons. It is very subjective but 200ms seems to be a
good value that accepts firm pushes but rejects very light ones. The key values
assigned to the buttons were arbitrarily chosen to be F1-F8.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Commit fcf173e451 (usb: musb: add names for IRQs
in structure resource) forgot to assign name to the DA8xx MUSB IRQ resource.
Because of that MUSB driver fails to load on DA8xx machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Ensure that the at24 eeprom driver is selected for certain boards that
need boot data (e.g. MAC address) from EEPROM.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There was a single case of 'da850evm' prefix in the board-da850-evm.c file
where the reset of the prefixes were 'da850_evm'; change it to 'da850_evm' for
consistency.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Change the mach-davinci Kconfig file so that GPIO_PCA953X is default when
MACH_DAVINCI_DA850_EVM is set instead of always selecting. This allows users
to compile pca953x as a module.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sergei Shtylyov <sshtylyov@mvista.com>
CC: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the RMII PHY on the UI board is enabled with CONFIG_DA850_UI_RMII
then then following will be printed to the console when warnings are
also enabled:
WARNING: at drivers/gpio/gpiolib.c:1567 __gpio_set_value+0x4c/0x5c()
Modules linked in:
[<c002c6ac>] (unwind_backtrace+0x0/0xf8) from [<c003b48c>] (warn_slowpath_common+0x4c/0x64)
[<c003b48c>] (warn_slowpath_common+0x4c/0x64) from [<c003b4c0>] (warn_slowpath_null+0x1c/0x24)
[<c003b4c0>] (warn_slowpath_null+0x1c/0x24) from [<c01aed60>] (__gpio_set_value+0x4c/0x5c)
[<c01aed60>] (__gpio_set_value+0x4c/0x5c) from [<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x2
44)
[<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x244) from [<c02e2e1c>] (pca953x_probe+0x1f8/0x29
0)
<snip>
Traced the WARN_ON to the gpio_set_value(rmii_sel,0) call in
da850_evm_setup_emac_rmii. Replacing the call with the _cansleep variant
results in no more warning. Also replacing the gpio_set_value calls in the
teardown function.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
aemif_calc_rate() can return a negative error value, so all the
variables that get tested for this value need to be signed.
The maximum bit width of WSETUP(WSETUP_MAX) appears to be 30 bits
(0xf << 26). Using a signed instead of an unsigned integer
shouldn't make a difference here.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A common do-while loop can be factored out from the end of
the branches.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch applies the following modifications to the tnetv107x clock tree:
- reparent tnetv107x usb clocks to usbss
- mark timer1 as always enabled
- enable set_rate on pll divider output clocks
- adjust tnetv107x tsc sysclk rate lower to fix invalid reset defaults
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the sysclk rate setting code to use the divider mask
specified in pll_data. Without this, devices with different divider ranges
(e.g. tnetv107x) fail.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Overwrite the default implementation of sched_clock that is based on
jiffies by something more precise. This improves timestamps in ftrace.
Implementation is copied from OMAP platform code.
Signed-off-by: Andreas Gaeer <Andreas.Gaer@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
