When the binding was converted it appeared necessary to set
'unevaluatedProperties: true' because of the switch devices on the
turris-mox board. Actually the error was because of the reg property
being incorrect causing the rest of the properties to be unevaluated.
After the reg properties are fixed for turris-mox we can set
'unevaluatedProperties: false' as is generally expected.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO devices have #address-cells = <1>, #size-cells = <0>. Now that we
have a schema enforcing this for marvell,orion-mdio we can see that the
turris-mox has a unnecessary 2nd cell for the switch nodes reg property
of it's switch devices. Remove the unnecessary 2nd cell from the
switches reg property.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Ramadoss says:
====================
net: dsa: microchip: refactor the ksz switch init function
During the ksz_switch_register function, it calls the individual switches init
functions (ksz8795.c and ksz9477.c). Both these functions have few things in
common like, copying the chip specific data to struct ksz_dev, allocating
ksz_port memory and mib_names memory & cnt. And to add the new LAN937x series
switch, these allocations has to be replicated.
Based on the review feedback of LAN937x part support patch, refactored the
switch init function to move allocations to switch register.
Link:https://patchwork.kernel.org/project/netdevbpf/patch/20220504151755.11737-8-arun.ramadoss@microchip.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The name, regs_size and overrides members in struct ksz_device are
unused. Hence remove it.
And host_mask is used in only place of ksz8795.c file, which can be
replaced by dev->info->cpu_ports
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for phylink_get_caps for ksz8795 and ksz9477
series switch. It updates the struct ksz_switch_chip with the details of
the internal phys and xmii interface. Then during the get_caps based on
the bits set in the structure, corresponding phy mode is set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mib->cnt_ptr resetting is handled in multiple places as part of
port_init_cnt(). Hence moved mib->cnt_ptr code to ksz common layer
and removed from individual product files.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 uses the same algorithm for copying the ethtool
strings. Hence moved to ksz_common to remove the redundant code.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 init function initializes the memory to dev->ports,
mib counters and assigns the ds real number of ports. Since both the
routines are same, moved the allocation of port memory to
ksz_switch_register after init.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz88xx family has one set of mib_names. The ksz87xx, ksz9477,
LAN937x based switches has one set of mib_names. In order to remove
redundant declaration, moved the struct mib_names to ksz_chip_data
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch perform the compatibility check for the device after the chip
detect is done. It is to prevent the mismatch between the device
compatible specified in the device tree and actual device found during
the detect. The ksz9477 device doesn't use any .data in the
of_device_id. But the ksz8795_spi uses .data for assigning the regmap
between 8830 family and 87xx family switch. Changed the regmap
assignment based on the chip_id from the .data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz_chip_data in ksz8795 and ksz9477 to ksz_common.
At present, the dev->chip_id is iterated with the ksz_chip_data and then
copy its value to the ksz_dev structure. These values are declared as
constant.
Instead of copying the values and referencing it, this patch update the
dev->info to the ksz_chip_data based on the chip_id in the init
function. And also update the ksz_chip_data values for the LAN937x based
switches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port_cnt value in the structure is not used in the switch_init.
Instead it uses the fls(chip->cpu_port), this is due to one of port in
the ksz8794 unavailable. The cpu_port for the 8794 is 0x10, fls(0x10) =
5, hence updating it directly in the ksz_chip_data structure in order to
same with all the other switches in ksz8795.c and ksz9477.c files.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MISC updates to mlx5 dirver
1) Aya Levin allows relaxed ordering over VFs
2) Gal Pressman Adds support XDP SQs for uplink representors in switchdev mode
3) Add debugfs TC stats and command failure syndrome for debuggability
4) Tariq uses variants of vzalloc where it could help
5) Multiport eswitch support from Elic Cohen:
Eli Cohen Says:
===============
The multiport eswitch feature allows to forward traffic from a
representor net device to the uplink port of an associated eswitch's
uplink port.
This feature requires creating a LAG object. Since LAG can be created
only once for a function, the feature is mutual exclusive with either
bonding or multipath.
Multipath eswitch mode is entered automatically these conditions are
met:
1. No other LAG related mode is active.
2. A rule that explicitly forwards to an uplink port is inserted.
The implementation maintains a reference count on such rules. When the
reference count reaches zero, the LAG is released and other modes may be
used.
When an explicit rule that explicitly forwards to an uplink port is
inserted while another LAG mode is active, that rule will not be
offloaded by the hardware since the hardware cannot guarantee that the
rule will actually be forwarded to that port.
Example rules that forwards to an uplink port is:
$ tc filter add dev rep0 root flower action mirred egress \
redirect dev uplinkrep0
$ tc filter add dev rep0 root flower action mirred egress \
redirect dev uplinkrep1
This feature is supported only if LAG_RESOURCE_ALLOCATION firmware
configuration parameter is set to true.
The series consists of three patches:
1. Lag state machine refactor
This patch does not add new functionality but rather changes the way
the state of the LAG is maintained.
2. Small fix to remove unused argument.
3. The actual implementation of the feature.
===============
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmKElS8ACgkQSD+KveBX
+j6uKAf9GJrtngu198xdnood2qfxsiZ6x+wYsBVW/uOb36xp13XkbM78pr37Vp08
y/IvK07u+VrsgnoQLVqNyCosKaja5rdaHW/E8qa4mGnYo2j1DIjTNDPJVPiazL6+
FfHUBRmVjiPaEoF5FS7ezu7AMNqxfqSqcojsrk/j+5Ic/1AbNidZD015uIxmqg95
rnS3V7UFV7LlMMVGPWidF2QBBQAbddsqGSpYBOowBu8MuPExuJfqH7nxxem0ATLH
RLoU5MghM+Ny1s6ZfccKtl/TIrFBcxu0IATmacmUlp/0Hmv7apuBFredbxJ0D4bF
cHgaOU+80UBEEFs31K0a3+neisL+ug==
=0VhX
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2022-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2022-05-17
MISC updates to mlx5 dirver
1) Aya Levin allows relaxed ordering over VFs
2) Gal Pressman Adds support XDP SQs for uplink representors in switchdev mode
3) Add debugfs TC stats and command failure syndrome for debuggability
4) Tariq uses variants of vzalloc where it could help
5) Multiport eswitch support from Elic Cohen:
Eli Cohen Says:
===============
The multiport eswitch feature allows to forward traffic from a
representor net device to the uplink port of an associated eswitch's
uplink port.
This feature requires creating a LAG object. Since LAG can be created
only once for a function, the feature is mutual exclusive with either
bonding or multipath.
Multipath eswitch mode is entered automatically these conditions are
met:
1. No other LAG related mode is active.
2. A rule that explicitly forwards to an uplink port is inserted.
The implementation maintains a reference count on such rules. When the
reference count reaches zero, the LAG is released and other modes may be
used.
When an explicit rule that explicitly forwards to an uplink port is
inserted while another LAG mode is active, that rule will not be
offloaded by the hardware since the hardware cannot guarantee that the
rule will actually be forwarded to that port.
Example rules that forwards to an uplink port is:
$ tc filter add dev rep0 root flower action mirred egress \
redirect dev uplinkrep0
$ tc filter add dev rep0 root flower action mirred egress \
redirect dev uplinkrep1
This feature is supported only if LAG_RESOURCE_ALLOCATION firmware
configuration parameter is set to true.
The series consists of three patches:
1. Lag state machine refactor
This patch does not add new functionality but rather changes the way
the state of the LAG is maintained.
2. Small fix to remove unused argument.
3. The actual implementation of the feature.
===============
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiport eswitch mode is a LAG mode that allows to add rules that
forward traffic to a specific physical port without being affected by LAG
affinity configuration.
This mode of operation is mutual exclusive with the other LAG modes used
by multipath and bonding.
To make the transition between the modes, we maintain a counter on the
number of rules specifying one of the uplink representors as the target
of mirred egress redirect action.
An example of such rule would be:
$ tc filter add dev enp8s0f0_0 prot all root flower dst_mac \
00:11:22:33:44:55 action mirred egress redirect dev enp8s0f0
If the reference count just grows to one and LAG is not in use, we
create the LAG in multiport eswitch mode. Other mode changes are not
allowed while in this mode. When the reference count reaches zero, we
destroy the LAG and let other modes be used if needed.
logic also changed such that if forwarding to some uplink destination
cannot be guaranteed, we fail the operation so the rule will eventually
be in software and not in hardware.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Argument ndev is not used in mlx5_handle_changeupper_event()
Remove it.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
LAG state machine is implemented using bit flags. However, all these bit
flags, except for MLX5_LAG_FLAG_HASH_BASED, are really mutual exclusive.
In addition, MLX5_LAG_FLAG_READY is used by bonding to mark if we have
our netdevices successfully added to lag and does not really belong in
the same flags variable as the other flags.
Rename MLX5_LAG_FLAG_READY to MLX5_LAG_FLAG_NDEVS_READY to better
reflect its purpose and put it in a new flags variable.
For the rest of the flags, we introduce a mode enum to hold the state
of the LAG.
Remove the shared fdb boolean flag from struct mlx5_lag and store this
configuration as a mode flag.
Change all flag related operations to use standard Linux APIs.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This patch adds the XDP SQs to the uplink representors steering tables
in swichdev mode and enables XDP usage on them.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Correct the calculation of maximum channels of rep to better utilize
the hardware resources and allow a larger scale of reps.
This will allow creation of all virtual ports configured.
Fixes: 473baf2e9e ("net/mlx5e: Allow profile-specific limitation on max num of channels")
Signed-off-by: Moshe Tal <moshet@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Connection offload is translated to multiple rules over several
hardware flow tables. Unhandled end-cases may cause a hardware
resource leak causing multiple system symptoms such as a host
memory leak, decreased performance and other scale related issues.
Export the current number of firmware FTEs related to the CT table
as a debugfs counter. Also add a dropped packets counter to help
debug packets dropped on restore failure.
To show the offloaded count:
cat /sys/kernel/debug/mlx5/<PCI>/ct_nic/offloaded
To show the dropped count:
cat /sys/kernel/debug/mlx5/<PCI>/ct_nic/rx_dropped
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Roi Dayan <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
By PCI spec, the config space of the VF always report relaxed ordering
not supported while it inherits this property from its PF. Hence using
pcie_relaxed_ordering_enable(), always disables the relaxed ordering on
all VFs. Remove this check and rely on the firmware which queries the
config space of the PF and set the capability bit accordingly.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Marina Varshaver <marinav@nvidia.com>
Reviewed-by: Gal Shalom <galshalom@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Offloading outer checksum on tunnels requires GSO partial, add it to
'vlan_features' to allow offloading tunnels over vlans.
For example, running GENEVE over vlan & ipv6 (mandatory UDP checksum)
now allows for hardware TSO instead of software segmentation in GSO
only.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Followup commit
79ce39be1d ("net/mlx5e: Improve ethtool rxnfc callback structure")
and handle CONFIG_MLX5_EN_RXNFC enabled/disabled inside the fs layer so
the ethtool callbacks are always available. The fs layer will provide
stubs when CONFIG_MLX5_EN_RXNFC is compiled out.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Physical continuity is not necessary, and requested allocation size might
be larger than PAGE_SIZE.
Hence, use v-alloc/free API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Physical continuity is not necessary, and requested allocation size might
be larger than PAGE_SIZE.
Hence, use v-alloc/free API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Physical continuity is not necessary, and requested allocation size might
be larger than PAGE_SIZE.
Hence, use v-alloc/free API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Physical continuity is not necessary, and requested allocation size might
be larger than PAGE_SIZE.
Hence, use v-alloc/free API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Take the wrapper version which picks default node into a header file.
This reduces the number of exported functions.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add syndrome of last command failure per command type to debugfs to ease
debugging of such failure.
last_failed_syndrome - last command failed syndrome returned by FW.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Added support for adaptive IRQ coalescing. It uses net_dim
algorithm to find the suitable delay/IRQ count based on the
current packet rate.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20220517044055.876158-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use TOD_READ_SECONDARY for extts to keep TOD_READ_PRIMARY
for gettime and settime exclusively. Before this change,
TOD_READ_PRIMARY was used for both extts and gettime/settime,
which would result in changing TOD read/write triggers between
operations. Using TOD_READ_SECONDARY would make extts
independent of gettime/settime operation
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/1652712427-14703-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following coccicheck warning:
drivers/net/ethernet/smsc/smc911x.c:483:20-22: WARNING opportunity for min()
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Link: https://lore.kernel.org/r/20220516115627.66363-1-guozhengkui@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guangguan Wang says:
====================
net/smc: send and write inline optimization for smc
Send cdc msgs and write data inline if qp has sufficent inline
space, helps latency reducing.
In my test environment, which are 2 VMs running on the same
physical host and whose NICs(ConnectX-4Lx) are working on
SR-IOV mode, qperf shows 0.4us-1.3us improvement in latency.
Test command:
server: smc_run taskset -c 1 qperf
client: smc_run taskset -c 1 qperf <server ip> -oo \
msg_size:1:2K:*2 -t 30 -vu tcp_lat
The results shown below:
msgsize before after
1B 11.9 us 10.6 us (-1.3 us)
2B 11.7 us 10.7 us (-1.0 us)
4B 11.7 us 10.7 us (-1.0 us)
8B 11.6 us 10.6 us (-1.0 us)
16B 11.7 us 10.7 us (-1.0 us)
32B 11.7 us 10.6 us (-1.1 us)
64B 11.7 us 11.2 us (-0.5 us)
128B 11.6 us 11.2 us (-0.4 us)
256B 11.8 us 11.2 us (-0.6 us)
512B 11.8 us 11.3 us (-0.5 us)
1KB 11.9 us 11.5 us (-0.4 us)
2KB 12.1 us 11.5 us (-0.6 us)
====================
Link: https://lore.kernel.org/r/20220516055137.51873-1-guangguan.wang@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rdma write with inline flag when sending small packages,
whose length is shorter than the qp's max_inline_data, can
help reducing latency.
In my test environment, which are 2 VMs running on the same
physical host and whose NICs(ConnectX-4Lx) are working on
SR-IOV mode, qperf shows 0.5us-0.7us improvement in latency.
Test command:
server: smc_run taskset -c 1 qperf
client: smc_run taskset -c 1 qperf <server ip> -oo \
msg_size:1:2K:*2 -t 30 -vu tcp_lat
The results shown below:
msgsize before after
1B 11.2 us 10.6 us (-0.6 us)
2B 11.2 us 10.7 us (-0.5 us)
4B 11.3 us 10.7 us (-0.6 us)
8B 11.2 us 10.6 us (-0.6 us)
16B 11.3 us 10.7 us (-0.6 us)
32B 11.3 us 10.6 us (-0.7 us)
64B 11.2 us 11.2 us (0 us)
128B 11.2 us 11.2 us (0 us)
256B 11.2 us 11.2 us (0 us)
512B 11.4 us 11.3 us (-0.1 us)
1KB 11.4 us 11.5 us (0.1 us)
2KB 11.5 us 11.5 us (0 us)
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: kernel test robot <lkp@intel.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As cdc msg's length is 44B, cdc msgs can be sent inline in
most rdma devices, which can help reducing sending latency.
In my test environment, which are 2 VMs running on the same
physical host and whose NICs(ConnectX-4Lx) are working on
SR-IOV mode, qperf shows 0.4us-0.7us improvement in latency.
Test command:
server: smc_run taskset -c 1 qperf
client: smc_run taskset -c 1 qperf <server ip> -oo \
msg_size:1:2K:*2 -t 30 -vu tcp_lat
The results shown below:
msgsize before after
1B 11.9 us 11.2 us (-0.7 us)
2B 11.7 us 11.2 us (-0.5 us)
4B 11.7 us 11.3 us (-0.4 us)
8B 11.6 us 11.2 us (-0.4 us)
16B 11.7 us 11.3 us (-0.4 us)
32B 11.7 us 11.3 us (-0.4 us)
64B 11.7 us 11.2 us (-0.5 us)
128B 11.6 us 11.2 us (-0.4 us)
256B 11.8 us 11.2 us (-0.6 us)
512B 11.8 us 11.4 us (-0.4 us)
1KB 11.9 us 11.4 us (-0.5 us)
2KB 12.1 us 11.5 us (-0.6 us)
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: kernel test robot <lkp@intel.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As per Errata Section 5.1, if EEE is intended to be used, some register
writes must be done once after every hardware reset. This patch now adds
the necessary register writes as listed in the Marvell errata.
Without this fix we experience ethernet problems on some of our boards
equipped with a new version of this ethernet PHY (different supplier).
The fix applies to Marvell Alaska 88E1510/88E1518/88E1512/88E1514
Rev. A0.
Signed-off-by: Leszek Polak <lpolak@arri.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220516070859.549170-1-sr@denx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220516082251.1651350-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220516081914.1651281-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220516072646.1651109-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_kfree check the pointer, there is no need to check before
devm_kfree call.
This change is to cleanup the code a bit.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Link: https://lore.kernel.org/r/20220516015208.6526-1-bernard@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmKCr/0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXbVWCAClh9ywNEPiSxXsB2k9EdVoijz0hv6I
y6YLFPfHxc8w0ewOnBxJOBeLhVjIE2K3n81NaEudheBBImWV8CGlFPHu5sI4S01b
aFcAuLT6SOat52xzkh44WGGjW517+EZM1Of1xzPhKdnR0nLvva52SpJlYwgLrkCN
O6r30cDuU558H4g2BNxavbbNFPzL7HhkBpHmgWQg4q2p7LvLuTE6sN2CvNEgUWYM
nIyK6P/FIyy3l7M7E873WhIEGNGRnAXRBEPXivRmKTlw0wizcvPxlWKm4YxTA0WL
30fw58Hy4x6SZD+7+sP0QhdjiYOofgMtZFZn/LaJYE+rfaYLsFUH3A/2
=tUrE
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.19-20220516' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-05-16
the first 2 patches are by me and target the CAN raw protocol. The 1st
removes an unneeded assignment, the other one adds support for
SO_TXTIME/SCM_TXTIME.
Oliver Hartkopp contributes 2 patches for the ISOTP protocol. The 1st
adds support for transmission without flow control, the other let's
bind() return an error on incorrect CAN ID formatting.
Geert Uytterhoeven contributes a patch to clean up ctucanfd's Kconfig
file.
Vincent Mailhol's patch for the slcan driver uses the proper function
to check for invalid CAN frames in the xmit callback.
The next patch is by Geert Uytterhoeven and makes the interrupt-names
of the renesas,rcar-canfd dt bindings mandatory.
A patch by my update the ctucanfd dt bindings to include the common
CAN controller bindings.
The last patch is by Akira Yokosawa and fixes a breakage the
ctucanfd's documentation.
* tag 'linux-can-next-for-5.19-20220516' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
docs: ctucanfd: Use 'kernel-figure' directive instead of 'figure'
dt-bindings: can: ctucanfd: include common CAN controller bindings
dt-bindings: can: renesas,rcar-canfd: Make interrupt-names required
can: slcan: slc_xmit(): use can_dropped_invalid_skb() instead of manual check
can: ctucanfd: Let users select instead of depend on CAN_CTUCANFD
can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting
can: isotp: add support for transmission without flow control
can: raw: add support for SO_TXTIME/SCM_TXTIME
can: raw: raw_sendmsg(): remove not needed setting of skb->sk
====================
Link: https://lore.kernel.org/r/20220516202625.1129281-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skb_data_area_size() is not needed. As Jakub pointed out [1]:
For Rx, drivers can use the size passed during skb allocation or
use skb_tailroom().
For Tx, drivers should use skb_headlen().
[1] https://lore.kernel.org/netdev/CAHNKnsTmH-rGgWi3jtyC=ktM1DW2W1VJkYoTMJV2Z_Bt498bsg@mail.gmail.com/
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
