We need the staging fixes in here too, and this resolves a merge issue
with the vt6656 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
-----BEGIN PGP SIGNATURE-----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=DyTF
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
-----BEGIN PGP SIGNATURE-----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=SmJy
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fe ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.
Issues seen prior to this were:
When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.
Fixes: 4599cac846 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d24517267 ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)
Fixes: 801a6e0af0 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fd ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Vitor Soares <vitor.soares@synopsys.com>
Tested-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.
Fixes: b852822474 ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's not uncommon that voltage regulator becomes available later during
kernel's boot process. This patch adds info message about unavailable
regulators in a case of the deferred-probe error and also amends the
error message with a error code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an object can be considered close to the sensor is hardware
dependent. Allowing to configure the property via device tree
allows to configure this device specific value.
This is useful for e.g. iio-sensor-proxy to indicate to userspace
if an object is close to the sensor.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to https://www.analog.com/, the company name is spelled
"Analog Devices".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
This change reworks the predisable/postenable hooks so that the pollfunc is
attached/detached in the correct position.
It also balances the calls a bit, by grouping the preenable and the
iio_triggered_buffer_postenable() into a single
isl29125_buffer_postenable() function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together. Reduces boilerplate and suggested
by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This only occurs once in the driver and isn't needed in this case either,
so drop it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Given the parameter is void *, casting to u8 * is unnecessary.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Casts to u8 * for the val parameter which is void * and so needs no cast.
* Explicit sizes when we can use sizeof on the destination / source variable.
Not broken in anyway, I'm just trying to tidy up the is in the subsystem to
avoid it getting cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Unnecessary casts of val parameter to u8 * which makes little sense as
the function take a void *.
* Explicit sizes where we can use the destination type to define that.
Note that's not true in all cases as we do read 3 bytes into 4 byte
destinations.
Note that noting was broken here, I'm just trying to ensure this doesn't
get cut and paste into more drivers so cleaning these out subsystem wide.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
st_lsm6dsx is a standalone driver for STM IMU sensors and does not rely
on st_sensor common framework, so it does not include st_sensor common
definitions.
In st_lsm6dsx_shub driver st_sensors.h is used just to introduce the
default wai address for LIS3MDL sensor.
Drop this largely unconnected include file and introduce the default wai
address for LIS3MDL in st_lsm6dsx_ext_dev_settings register map
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
This is the last user of 'devm_iio_device_match()', so it can be removed as
well in this patch.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Moves this to be the first check, as it's very simple and fails the
registration earlier, instead of potentially initializing the
'indio_dev->label' and checking for duplicate indexes, and then failing
with this simple-check.
This is a minor optimization, since '__iio_device_register()' will waste
fewer validation cycles in case 'indio_dev->info' is NULL.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This field doesn't seem used. It seems that only 'buffer->attrs' was ever
used to extend sysfs attributes for an IIO buffer.
Moving forward, it may not make sense to keep it. This patch removes the
field and it's initialization code.
Since we want to rework IIO buffer, to be able to add more buffers per IIO
device, we will merge [somehow] the 'buffer' & 'scan_elements' groups, and
we will continue to add the attributes to the 'buffer' group.
Removing it here, will also make the rework here a bit smaller, since
this code will not be present.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 1fd4567026 ("iio: imu: adis: add support product ID check in adis_initial_startup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a typo. 'at the a time' -> 'at a time'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO DMA buffer is a DMA buffer implementation. As such it should
include buffer_impl.h rather than buffer.h.
The include to buffer.h in buffer-dma.h should be buffer_impl.h so it has
access to the struct iio_buffer definition. The code currently only works
because all places that use buffer-dma.h include buffer_impl.h before it.
The include to buffer.h in industrialio-buffer-dma.c can be removed since
those file does not reference any of buffer consumer functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add driver for the Maxim MAX1241 12-bit, single-channel ADC.
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX1240-MAX1241.pdf
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Lazar <alazar@startmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STMicroelectronics LISHH12 accelerometer in st_accel
framework.
https://www.st.com/resource/en/datasheet/lis2hh12.pdf
Signed-off-by: Gaëtan André <rvlander@gaetanandre.eu>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add LIS3MDL register map to sensor hub device table.
Tested with LSM6DSM.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for sensor with up to 8 different ODR settings.
Required for supporting LIS3MDL as sensor hub slave device.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
debugfs_create_file_unsafe does not protect the fops handed to it
against file removal. DEFINE_DEBUGFS_ATTRIBUTE makes the fops aware of
the file lifetime and thus protects it against removal.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Tested-by Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
debugfs_create_file_unsafe does not protect the fops handed to it
against file removal. DEFINE_DEBUGFS_ATTRIBUTE makes the fops aware of
the file lifetime and thus protects it against removal.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Tested-by Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce st_lsm6dsx_shub_set_full_scale routine in order to configure
the i2c slave device sensitivity
Tested-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD9467 is a 16-bit, monolithic, IF sampling analog-to-digital converter
(ADC). It is optimized for high performanceover wide bandwidths and ease of
use. The product operates at a 250 MSPS conversion rate and is designed for
wireless receivers, instrumentation, and test equipment that require a high
dynamic range. The ADC requires 1.8 V and 3.3 V power supplies and a low
voltage differential input clock for full performance operation. No
external reference or driver components are required for many applications.
Data outputs are LVDS compatible (ANSI-644 compatible) and include the
means to reduce the overall current needed for short trace distances.
Since the chip can operate at such high sample-rates (much higher than
classical interfaces), it requires that a DMA controller be used to
interface directly to the chip and push data into memory.
Typically, the AXI ADC IP core is used to interface with it.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/AD9467.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).
Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.
Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.
There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.
DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
