[ Upstream commit 84d94e16ef ]
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.
This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.
Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103205827.14559-1-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1040b0d42 ]
Don't set Accessed/Dirty bits for a struct page with PG_reserved set,
i.e. don't set A/D bits for the ZERO_PAGE. The ZERO_PAGE (or pages
depending on the architecture) should obviously never be written, and
similarly there's no point in marking it accessed as the page will never
be swapped out or reclaimed. The comment in page-flags.h is quite clear
that PG_reserved pages should be managed only by their owner, and
strictly following that mandate also simplifies KVM's logic.
Fixes: 7df003c852 ("KVM: fix overflow of zero page refcount with ksm running")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220429010416.2788472-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e57ffb6e3 ]
Think about the below scene:
CPU1 CPU2
memunmap_pages
percpu_ref_exit
__percpu_ref_exit
free_percpu(percpu_count);
/* percpu_count is freed here! */
get_dev_pagemap
xa_load(&pgmap_array, PHYS_PFN(phys))
/* pgmap still in the pgmap_array */
percpu_ref_tryget_live(&pgmap->ref)
if __ref_is_percpu
/* __PERCPU_REF_ATOMIC_DEAD not set yet */
this_cpu_inc(*percpu_count)
/* access freed percpu_count here! */
ref->percpu_count_ptr = __PERCPU_REF_ATOMIC_DEAD;
/* too late... */
pageunmap_range
To fix the issue, do percpu_ref_exit() after pgmap_array is emptied. So
we won't do percpu_ref_tryget_live() against a being freed percpu_ref.
Link: https://lkml.kernel.org/r/20220609121305.2508-1-linmiaohe@huawei.com
Fixes: b7b3c01b19 ("mm/memremap_pages: support multiple ranges per invocation")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b80892ca02 ]
No driver is left using the external pgmap refcount, so remove the
code to support it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211028151017.50234-1-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed913b055a ]
If make_device_exclusive_range() fails or returns pages marked for
exclusive access less than required, remaining fields of pages will left
uninitialized. So dmirror_atomic_map() will access those yet
uninitialized fields of pages. To fix it, do dmirror_atomic_map() iff all
pages are marked for exclusive access (we will break if mapped is less
than required anyway) so we won't access those uninitialized fields of
pages.
Link: https://lkml.kernel.org/r/20220609130835.35110-1-linmiaohe@huawei.com
Fixes: b659baea75 ("mm: selftests for exclusive device memory")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edabcf71d1 ]
Original assert/deassert bit is BIT(0), but it's more resonable to modify
them to BIT(id % 32) which is based on id.
This patch will not influence any previous driver because the reset is
only used for thermal. The id (MT8183_INFRACFG_AO_THERM_SW_RST) is 0.
Fixes: 64ebb57a3d ("clk: reset: Modify reset-controller driver")
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220523093346.28493-3-rex-bc.chen@mediatek.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bd2dc6ea8 ]
Reordering of header files and removing the iio/sysfs.h since
custom attributes are not being used in the driver.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-3-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74bb746407 ]
The last resume result exposing logic in cros_ec_sleep_event()
incorrectly requires S0ix support, which doesn't work on ARM based
systems where S0ix doesn't exist. That's because cros_ec_sleep_event()
only reports the last resume result when the EC indicates the last sleep
event was an S0ix resume. On ARM systems, the last sleep event is always
S3 resume, but the EC can still detect sleep hang events in case some
other part of the AP is blocking sleep.
Always expose the last resume result if the EC supports it so that this
works on all devices regardless of S0ix support. This fixes sleep hang
detection on ARM based chromebooks like Trogdor.
Cc: Rajat Jain <rajatja@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Fixes: 7235560ac7 ("platform/chrome: Add support for v1 of host sleep event")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220614075726.2729987-1-swboyd@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 747c7cf159 ]
Changing the scale macro values to match the bma400 sensitivity
for 1 LSB of all the available ranges.
Fixes: 465c811f1f ("iio: accel: Add driver for the BMA400")
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-2-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec538eb838 ]
The driver failed to send implicit logout on session delete. For edif, this
failed to flush any lingering SA index in FW.
Set a flag to turn on implicit logout early in the session recovery to make
sure the logout will go out in case of error.
Link: https://lore.kernel.org/r/20220608115849.16693-8-njavali@marvell.com
Fixes: 4de067e5df ("scsi: qla2xxx: edif: Add N2N support for EDIF")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8fdfb0b39 ]
Current code prematurely sends out PRLI before authentication application
has given the OK to do so. This causes PRLI failure and session teardown.
Prevents PRLI from going out before authentication app gives the OK.
Link: https://lore.kernel.org/r/20220608115849.16693-7-njavali@marvell.com
Fixes: 91f6f5fbe8 ("scsi: qla2xxx: edif: Reduce connection thrash")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24c796098f ]
The scenario is this: User loaded driver but has not started authentication
app. All sessions to secure device will exhaust all login attempts, fail,
and in stay in deleted state. Then some time later the app is started. The
driver will replenish the login retry count, trigger delete to prepare for
secure login. After deletion, relogin is triggered.
For the session that is already deleted, the delete trigger is a no-op. If
none of the sessions trigger a relogin, no progress is made.
Add a relogin trigger.
Link: https://lore.kernel.org/r/20220608115849.16693-5-njavali@marvell.com
Fixes: 7ebb336e45 ("scsi: qla2xxx: edif: Add start + stop bsgs")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b659ed67a ]
If the session is down and the local port continues to receive AUTH ELS
messages, the driver needs to send back LOGO so that the remote device
knows to tear down its session. Terminate and clean up the AUTH ELS
exchange followed by a passthrough LOGO.
Link: https://lore.kernel.org/r/20220608115849.16693-3-njavali@marvell.com
Fixes: 225479296c ("scsi: qla2xxx: edif: Reject AUTH ELS on session down")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20646f5b1e ]
Commit e2be04c7f9 ("License cleanup: add SPDX license identifier to
uapi header files with a license") added the correct SPDX identifier to
include/uapi/linux/netfilter/xt_IDLETIMER.h.
A subsequent commit removed it for no reason and reintroduced the UAPI
license incorrectness as the file is now missing the UAPI exception
again.
Add it back and remove the GPLv2 boilerplate while at it.
Fixes: 68983a354a ("netfilter: xtables: Add snapshot of hardidletimer target")
Cc: Manoj Basapathi <manojbm@codeaurora.org>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: netfilter-devel@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fc7c435b ]
In the function tegra_xusb_powerdomain_init(),
dev_pm_domain_attach_by_name() may return NULL in some cases,
so IS_ERR() doesn't meet the requirements. Thus fix it.
Fixes: 6494a9ad86 ("usb: xhci: tegra: Add genpd support")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20220524121404.18376-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 302970b4ca ]
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 73108aa90c ("USB: ohci-nxp: Use isp1301 driver")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220603141231.979-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5c5b13cb4 ]
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 796bcae736 ("USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220602110849.58549-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df84a757d ]
Fix the "comparison with less than zero" warning reported by
cppcheck for the unsigned (size_t) parameter count of the
alt_pr_fpga_write() function.
Fixes: d201cc17a8 ("fpga pr ip: Core driver support for Altera Partial Reconfiguration IP")
Reviewed-by: Tom Rix <trix@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Link: https://lore.kernel.org/r/20220609140520.42662-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf038503d5 ]
of_get_child_by_name() returns a node pointer with refcount incremented, so
we should use of_node_put() on it when we don't need it anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 814cceebba ("PCI: mediatek-gen3: Add INTx support")
Link: https://lore.kernel.org/r/20220601041259.56185-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28607b426c ]
For all but one error path clk_disable_unprepare() is already there. Add
it to the one location where it's missing.
Fixes: 481815a619 ("mtd: st_spi_fsm: Handle clk_prepare_enable/clk_disable_unprepare.")
Fixes: 69d5af8d01 ("mtd: st_spi_fsm: Obtain and use EMI clock")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e607879b0d ]
of_find_node_by_path() returns a node pointer with refcount incremented,
we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bb17230c61 ("mtd: parsers: ofpart: support BCM4908 fixed partitions")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220605070726.5979-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f7e62815c ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 2379608809 ("mtd: partitions: redboot: seek fis-index-block in the right node")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220526110652.64849-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a61528d997 ]
There is a deadlock between sm_release and sm_cache_flush_work
which is a work item. The cancel_work_sync in sm_release will
not return until sm_cache_flush_work is finished. If we hold
mutex_lock and use cancel_work_sync to wait the work item to
finish, the work item also requires mutex_lock. As a result,
the sm_release will be blocked forever. The race condition is
shown below:
(Thread 1) | (Thread 2)
sm_release |
mutex_lock(&ftl->mutex) | sm_cache_flush_work
| mutex_lock(&ftl->mutex)
cancel_work_sync | ...
This patch moves del_timer_sync and cancel_work_sync out of
mutex_lock in order to mitigate deadlock.
Fixes: 7d17c02a01 ("mtd: Add new SmartMedia/xD FTL")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220524044841.10517-1-duoming@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 381583845d ]
Smatch warnings:
drivers/hid/hid-cp2112.c:793 cp2112_xfer() error: __memcpy()
'data->block[1]' too small (33 vs 255)
drivers/hid/hid-cp2112.c:793 cp2112_xfer() error: __memcpy() 'buf' too
small (64 vs 255)
The 'read_length' variable is provided by 'data->block[0]' which comes
from user and it(read_length) can take a value between 0-255. Add an
upper bound to 'read_length' variable to prevent a buffer overflow in
memcpy().
Fixes: 542134c037 ("HID: cp2112: Fix I2C_BLOCK_DATA transactions")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8fbd344a5 ]
pm_runtime_enable() will increase power disable depth. If
dw_pcie_ep_init() fails, we should use pm_runtime_disable() to balance it
with pm_runtime_enable().
Add missing pm_runtime_disable() for tegra_pcie_config_ep().
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/r/20220602031910.55859-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f030304fde ]
of_get_next_child() returns a node pointer with refcount incremented, so we
should use of_node_put() on it when we don't need it anymore.
mc_pcie_init_irq_domains() only calls of_node_put() in the normal path,
missing it in some error paths. Add missing of_node_put() to avoid
refcount leak.
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Link: https://lore.kernel.org/r/20220605055123.59127-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7fdc4db07 ]
For exynos auto v9's UFS MPHY, We should use 0x50 offset of TSRV register
configurations. So, it must be
s/PHY_TRSV_REG_CFG/PHY_TRSV_REG_CFG_AUTOV9/g
Fixes: d64519249e ("phy: samsung-ufs: support exynosauto ufs phy driver")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220603050536.61957-1-chanho61.park@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3741aec4c3 ]
If NRIPS is supported in hardware but disabled in KVM, set next_rip to
the next RIP when advancing RIP as part of emulating INT3 injection.
There is no flag to tell the CPU that KVM isn't using next_rip, and so
leaving next_rip is left as is will result in the CPU pushing garbage
onto the stack when vectoring the injected event.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Fixes: 66b7138f91 ("KVM: SVM: Emulate nRIP feature when reinjecting INT3")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <cd328309a3b88604daa2359ad56f36cb565ce2d4.1651440202.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd9e6da804 ]
Unwind the RIP advancement done by svm_queue_exception() when injecting
an INT3 ultimately "fails" due to the CPU encountering a VM-Exit while
vectoring the injected event, even if the exception reported by the CPU
isn't the same event that was injected. If vectoring INT3 encounters an
exception, e.g. #NP, and vectoring the #NP encounters an intercepted
exception, e.g. #PF when KVM is using shadow paging, then the #NP will
be reported as the event that was in-progress.
Note, this is still imperfect, as it will get a false positive if the
INT3 is cleanly injected, no VM-Exit occurs before the IRET from the INT3
handler in the guest, the instruction following the INT3 generates an
exception (directly or indirectly), _and_ vectoring that exception
encounters an exception that is intercepted by KVM. The false positives
could theoretically be solved by further analyzing the vectoring event,
e.g. by comparing the error code against the expected error code were an
exception to occur when vectoring the original injected exception, but
SVM without NRIPS is a complete disaster, trying to make it 100% correct
is a waste of time.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Fixes: 66b7138f91 ("KVM: SVM: Emulate nRIP feature when reinjecting INT3")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <450133cf0a026cb9825a2ff55d02cb136a1cb111.1651440202.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aec55325dd ]
After initiator has burned up all login retries, target authentication
application begins to run. This triggers a link bounce on target side.
Initiator will attempt another login. Due to N2N, the PRLI [nvme | fcp] can
fail because of the mode mismatch with target. This patch add a few more
login retries to revive the connection.
Link: https://lore.kernel.org/r/20220607044627.19563-11-njavali@marvell.com
Fixes: 4de067e5df ("scsi: qla2xxx: edif: Add N2N support for EDIF")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 789d54a417 ]
User failed to see disk via n2n topology. Driver used up all login retries
before authentication application started. When authentication application
started, driver did not have enough login retries to connect securely. On
app_start, driver will reset the login retry attempt count.
Link: https://lore.kernel.org/r/20220607044627.19563-10-njavali@marvell.com
Fixes: 4de067e5df ("scsi: qla2xxx: edif: Add N2N support for EDIF")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36f468bfe9 ]
db_flags field is a bit field. Replace value check with bit flag check.
Link: https://lore.kernel.org/r/20211026115412.27691-12-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91f6f5fbe8 ]
On ipsec start by remote port, target port may use RSCN to trigger
initiator to relogin. If driver is already in the process of a relogin,
then ignore the RSCN and allow the current relogin to continue. This
reduces thrashing of the connection.
Link: https://lore.kernel.org/r/20211026115412.27691-10-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0fb8ce2bb ]
When a thread is in the process of reestablish a session, a flag is set to
prevent multiple threads/triggers from doing the same task. This flag was
left on, and any attempt to relogin was locked out. Clear this flag if the
attempt has failed.
Link: https://lore.kernel.org/r/20220607044627.19563-6-njavali@marvell.com
Fixes: dd30706e73 ("scsi: qla2xxx: edif: Add key update")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c40c36e75 ]
This patch uses GFFID switch command to scan whether remote device is
Target or Initiator mode. Based on that info, driver will not pass up
Initiator info to authentication application. This helps reduce unnecessary
stress for authentication application to deal with unused connections.
Link: https://lore.kernel.org/r/20220607044627.19563-2-njavali@marvell.com
Fixes: 7ebb336e45 ("scsi: qla2xxx: edif: Add start + stop bsgs")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf9c4b961 ]
Presently ima_get_kexec_buffer() doesn't check if the previous kernel's
ima-kexec-buffer lies outside the addressable memory range. This can result
in a kernel panic if the new kernel is booted with 'mem=X' arg and the
ima-kexec-buffer was allocated beyond that range by the previous kernel.
The panic is usually of the form below:
$ sudo kexec --initrd initrd vmlinux --append='mem=16G'
<snip>
BUG: Unable to handle kernel data access on read at 0xc000c01fff7f0000
Faulting instruction address: 0xc000000000837974
Oops: Kernel access of bad area, sig: 11 [#1]
<snip>
NIP [c000000000837974] ima_restore_measurement_list+0x94/0x6c0
LR [c00000000083b55c] ima_load_kexec_buffer+0xac/0x160
Call Trace:
[c00000000371fa80] [c00000000083b55c] ima_load_kexec_buffer+0xac/0x160
[c00000000371fb00] [c0000000020512c4] ima_init+0x80/0x108
[c00000000371fb70] [c0000000020514dc] init_ima+0x4c/0x120
[c00000000371fbf0] [c000000000012240] do_one_initcall+0x60/0x2c0
[c00000000371fcc0] [c000000002004ad0] kernel_init_freeable+0x344/0x3ec
[c00000000371fda0] [c0000000000128a4] kernel_init+0x34/0x1b0
[c00000000371fe10] [c00000000000ce64] ret_from_kernel_thread+0x5c/0x64
Instruction dump:
f92100b8 f92100c0 90e10090 910100a0 4182050c 282a0017 3bc00000 40810330
7c0802a6 fb610198 7c9b2378 f80101d0 <a1240000> 2c090001 40820614 e9240010
---[ end trace 0000000000000000 ]---
Fix this issue by checking returned PFN range of previous kernel's
ima-kexec-buffer with page_is_ram() to ensure correct memory bounds.
Fixes: 467d278249 ("powerpc: ima: get the kexec buffer passed by the previous kernel")
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Prakhar Srivastava <prsriva@linux.microsoft.com>
Cc: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Cc: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Ritesh Harjani <ritesh.list@gmail.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220531041446.3334259-1-vaibhav@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec0da06337 ]
When meson_nfc_nand_chip_cleanup() is called, it will call:
meson_nfc_free_buffer(&meson_chip->nand);
nand_cleanup(&meson_chip->nand);
nand_cleanup() in turn will call nand_detach() which calls the
.detach_chip() which is here meson_nand_detach_chip().
meson_nand_detach_chip() already calls meson_nfc_free_buffer(), so we
could double free some memory.
Fix it by removing the unneeded explicit call to meson_nfc_free_buffer().
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/ec15c358b8063f7c50ff4cd628cf0d2e14e43f49.1653064877.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77087a04c8 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc1 ("mtd: physmap_of: add a hook for Versatile write protection")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220523143255.4376-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33ec82a6d2 ]
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc1 ("mtd: physmap_of: add a hook for Versatile write protection")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220523140205.48625-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2dee50ab9e ]
There are two UART clock groups, each having a mux to select its
upstream clock source. The register/bit definitions for accessing these
two muxes appear to have been reversed since introduction. Correct them
so as to match the hardware manual.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220518182527.1693156-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e51d8d3ea3 ]
When sensor discovery fails, this means that the system doesn't have
any sensors connected and a user should only be notified at most one time.
A message is already displayed at WARN level of "failed to discover,
sensors not enabled". It's pointless to show that the client init failed
at ERR level for the same condition.
Check the return code and don't display this message in those conditions.
Fixes: b5d7f43e97 ("HID: amd_sfh: Add support for sensor discovery")
Reported-by: David Chang <David.Chang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c31b14d86d ]
In case push_rcu() and related functions are buggy, there's a
WARN_ON(len >= 128), which the selftest tries to hit by being tricky. In
case it is hit, we shouldn't corrupt the kernel's stack, though;
otherwise it may be hard to even receive the report that it's buggy. So
conditionalize the stack write based on that WARN_ON()'s return value.
Note that this never *actually* happens anyway. The WARN_ON() in the
first place is bounded by IS_ENABLED(DEBUG), and isn't expected to ever
actually hit. This is just a debugging sanity check.
Additionally, hoist the constant 128 into a named enum,
MAX_ALLOWEDIPS_BITS, so that it's clear why this value is chosen.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/all/CAHk-=wjJZGA6w_DxA+k7Ejbqsq+uGK==koPai3sqdsfJqemvag@mail.gmail.com/
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151c8e499f ]
Using msleep() is problematic because it's compared against
ratelimiter.c's ktime_get_coarse_boottime_ns(), which means on systems
with slow jiffies (such as UML's forced HZ=100), the result is
inaccurate. So switch to using schedule_hrtimeout().
However, hrtimer gives us access only to the traditional posix timers,
and none of the _COARSE variants. So now, rather than being too
imprecise like jiffies, it's too precise.
One solution would be to give it a large "range" value, but this will
still fire early on a loaded system. A better solution is to align the
timeout to the actual coarse timer, and then round up to the nearest
tick, plus change.
So add the timeout to the current coarse time, and then
schedule_hrtimer() until the absolute computed time.
This should hopefully reduce flakes in CI as well. Note that we keep the
retry loop in case the entire function is running behind, because the
test could still be scheduled out, by either the kernel or by the
hypervisor's kernel, in which case restarting the test and hoping to not
be scheduled out still helps.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f56530dcdb ]
This refixes:
commit 7da17624e7
nt: usb: USB_RTL8153_ECM should not default to y
In general, device drivers should not be enabled by default.
which basically broke the commit it claimed to fix, ie:
commit 657bc1d10b
r8153_ecm: avoid to be prior to r8152 driver
Avoid r8153_ecm is compiled as built-in, if r8152 driver is compiled
as modules. Otherwise, the r8153_ecm would be used, even though the
device is supported by r8152 driver.
this commit amounted to:
drivers/net/usb/Kconfig:
+config USB_RTL8153_ECM
+ tristate "RTL8153 ECM support"
+ depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n)
+ default y
+ help
+ This option supports ECM mode for RTL8153 ethernet adapter, when
+ CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not
+ supported by r8152 driver.
drivers/net/usb/Makefile:
-obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o r8153_ecm.o
+obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o
+obj-$(CONFIG_USB_RTL8153_ECM) += r8153_ecm.o
And as can be seen it pulls a piece of the cdc_ether driver out into
a separate config option to be able to make this piece modular in case
cdc_ether is builtin, while r8152 is modular.
While in general, device drivers should indeed not be enabled by default:
this isn't a device driver per say, but rather this is support code for
the CDCETHER (ECM) driver, and should thus be enabled if it is enabled.
See also email thread at:
https://www.spinics.net/lists/netdev/msg767649.html
In:
https://www.spinics.net/lists/netdev/msg768284.html
Jakub wrote:
And when we say "removed" we can just hide it from what's prompted
to the user (whatever such internal options are called)? I believe
this way we don't bring back Marek's complaint.
Side note: these incorrect defaults will result in Android 13
on 5.15 GKI kernels lacking USB_RTL8153_ECM support while having
USB_NET_CDCETHER (luckily we also have USB_RTL8150 and USB_RTL8152,
so it's probably only an issue for very new RTL815x hardware with
no native 5.15 driver).
Fixes: 7da17624e7 ("nt: usb: USB_RTL8153_ECM should not default to y")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220730230113.4138858-1-zenczykowski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a41b17ff9d ]
In the case of sk->dccps_qpolicy == DCCPQ_POLICY_PRIO, dccp_qpolicy_full
will drop a skb when qpolicy is full. And the lock in dccp_sendmsg is
released before sock_alloc_send_skb and then relocked after
sock_alloc_send_skb. The following conditions may lead dccp_qpolicy_push
to add skb to an already full sk_write_queue:
thread1--->lock
thread1--->dccp_qpolicy_full: queue is full. drop a skb
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_full: queue is not full. no need to drop.
thread2--->unlock
thread1--->lock
thread1--->dccp_qpolicy_push: add a skb. queue is full.
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_push: add a skb!
thread2--->unlock
Fix this by moving dccp_qpolicy_full.
Fixes: b1308dc015 ("[DCCP]: Set TX Queue Length Bounds via Sysctl")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220729110027.40569-1-hbh25y@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
