The ADC of the S3C2416/2450 SoC is 10 or 12 bit wide, has its
source selection in the register base+0x18 and its width
selection in bit 03 of the ADCCON register.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C2443-adc is 10 bit wide and has its mux-select
in an extra register at base+0x18
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of S3C2443 and S3C2416 contain quirks not present
in the stock S3C24xx adc. Therefore allow them to alter the
device name via s3c_adc_setname.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mux bits in the adccon register should be cleared only
if muxing is really done in ADCCON and not another register.
This patch introduces a conditional for this.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of the S3C2443 and S3C2416 define some
additional registers and bits.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In drivers/gpio/gpio-samsung.c, there are certain structures
and functions which are not getting used if the particular
CPU is not selected. These code segments are moved under CPU
specific macros to remove compilation warnings.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some of the gpio chips of exynos4 are assigned a default gpio config without
the exynos4 specific pull up/down callbacks which resulted in incorrect
setting of pull up/down configuration.
Fix this by adding two new exynos4 specific entries in the array of default
configs with set_pull and get_pull callbacks set to exynos4 specific callbacks
The new default gpio configs can then be used for exynos4 gpio chips.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C64xx CPUs have TCMs so enable the kernel support for it
on these systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Only register gpio banks provided by SoC instead of the maximum possible
to lessen confusion, get rid of a warning from gpiolib and stop it from
eating into the extra gpios for configs with S3C24XX_GPIO_EXTRA != 0.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch registers all the available power domains on ORIGEN board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since the DC5V line is connected directly to the HDMI connector,
"hdmi-en" regulator would become a dummy regulator on origen board
(by defining REGULATOR_DUMMY in the kernel config file).
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sleep code for S5PV210 and EXYNOS4 are identical; moreover
S5p64X0 and S5PC100 for which support will be added soon can
use the same procedure. Create a common sleep code in the plat-s5p
directory so that it can be re-used.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pave the way for adding PM support on S5P64X0, which is more similar
to the S3C64XX series than the S5P series. Hence, the common pm code
(containing dummy functions) should not be used for S5P64X0.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves header files from plat-s5p to plat-samsung to
remove plat-s5p directory to make one plat-samsung directory
for Samsung SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves header files from plat-s3c24xx to plat-samsung to
remove plat-s3c24xx directory to make one plat-samsung directory for
Samsung SoCs. And this patch includes fixing coding style, too.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves SoC header files for supporting each SoCs to
plat-samsung directory. This is required to make one plat-
directory for Samsung SoCs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commit a3831cf ("ARM: Consolidate the
clkdev header files"), current mach/clkdev.h is no
needed in Samsung stuff.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sdhci platform helper function that sets up the default controller
configuration is removed for all Samsung platforms since such default
controller configuration can be handled by the driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definitions to enable support for s5p-fimc driver on
SMDKV310 board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support usb ehci device to the SMDKV310 board.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2416/S3C2450 use the same clocks for their i2s blocks
and can therefore reuse the existing ones.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch:
-- Adds platform device support for LCD-LTE480.
-- Adds platform data for FB with win_mode and default_bpp.
-- Enables FB device support and platform-lcd support.
-- Adds SPCON settings for LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch:
-- Adds platform device support for LCD-LTE480.
-- Adds platform data for FB with win_mode and default_bpp.
-- Enables FB device support and platform-lcd support.
-- Adds SPCON settings for LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds GPIO lines settings(HSYNC, VSYNC, VCLK and VD) for LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Set s3c_device_fb name as "s5p64x0-fb" for S5P6440 and S5P6450.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds:
-- Framebuffer related register mappings and bit fields.
-- IRQ number being used.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ever since it was written the Samsung DMA driver has had a TODO in the
hw_free() function wondering if we need to flush the DMA buffers. Up until
now the answer has been no but with the recent improvements Boojin has
done to the DMA infrastructure for the Samsung port the answer has changed
to yes for at least S3C6410 systems.
If we don't then when we next prepare() the channel the API will get
confused trying to run callbacks on the transfers hanging around from the
previous time the stream was open and oops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modifies PMU register setting function
to support the other EXYNOS4 SoCs.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add voltage regulator definitions for M-5MOLS camera, platform data
definition for the sensor and MIPI-CSI receiver drivers.
Add CAM power domain dependencies for FIMC and CSIS devices.
Define required I2C0 bus timings. Setup camera port A GPIO.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add platform data for CIF camera sensor and FIMC platform data
entries for it. Add platform device for s5p-fimc media device
driver and the camera port A I/O pins initialization.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform devices and regulators for TV devices on
Samsung Goni board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform devices and regulators for TV devices on
Samsung Universal C210 board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds all the resources for TV drivers and devices for Samsung
Exynos4 and S5PV210 platforms.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[m.szyprowski: squashed Exynos4 and S5PV210 patches and rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
