Currently we don't clear MSDC interrupts when cqe off/disable, which led
to the data complete interrupt will be reserved for the next command.
If the next command with data transfer after cqe off/disable, we process
the CMD ready interrupt and trigger DMA start for data, but the data
complete interrupt is already exists, then SW assume that the data transfer
is complete, SW will trigger DMA stop, but the data may not be transmitted
yet or is transmitting, so we may encounter the following error:
mtk-msdc 11230000.mmc: CMD bus busy detected.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220728080048.21336-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Add support for the asynchronous SDIO wakeup interrupts
- Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
- Add support to store error stats from host drivers
- Extend debugfs to show error stats from host drivers
- Add single I/O read support in the recovery path for 4k sector cards
MMC host:
- dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
- dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
- mmc_spi: Convert corresponding DT bindings to the dtschema
- mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
- mtk-sd: Add support for SDIO wake irqs
- mtk-sd: Add support for the Mediatek MT8188 variant
- renesas_sdhi: Drop redundant manual tap correction for newer SoCs
- renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
- sdhci/cqhci: Add support to capture stats from host errors
- sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
- sdhci-msm: Add support for the MSM8998 and SM8450 variant
- sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
- sdhci-pci-gli: Improve I/O read/write performance for GL9763E
- sdhci-s3c: Convert corresponding DT bindings to the dtschema
- tmio: Avoid glitches when resetting
MEMSTICK core:
- A couple of minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=Rmw5
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for the asynchronous SDIO wakeup interrupts
- Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
- Add support to store error stats from host drivers
- Extend debugfs to show error stats from host drivers
- Add single I/O read support in the recovery path for 4k sector cards
MMC host:
- dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
- dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
- mmc_spi: Convert corresponding DT bindings to the dtschema
- mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
- mtk-sd: Add support for SDIO wake irqs
- mtk-sd: Add support for the Mediatek MT8188 variant
- renesas_sdhi: Drop redundant manual tap correction for newer SoCs
- renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
- sdhci/cqhci: Add support to capture stats from host errors
- sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
- sdhci-msm: Add support for the MSM8998 and SM8450 variant
- sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
- sdhci-pci-gli: Improve I/O read/write performance for GL9763E
- sdhci-s3c: Convert corresponding DT bindings to the dtschema
- tmio: Avoid glitches when resetting
MEMSTICK core:
- A couple of minor fixes and cleanups"
* tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (61 commits)
mmc: mediatek: add support for SDIO eint wakup IRQ
mmc: core: Add support for SDIO wakeup interrupt
dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
dt-bindings: mmc: rockchip-dw-mshc: Document Rockchip RV1126
mmc: renesas_sdhi: newer SoCs don't need manual tap correction
mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
mmc: cavium-octeon: Add of_node_put() when breaking out of loop
mmc: core: quirks: Add of_node_put() when breaking out of loop
mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
dt-bindings: mmc: sdhci-msm: Document the SM8450 compatible
mmc: sdhci-msm: drop redundant of_device_id entries
dt-bindings: mmc: sdhci-msm: add MSM8998
mmc: block: Add single read for 4k sector cards
mmc: mxcmmc: Use mmc_card_sdio macro
mmc: core: Use mmc_card_* macro and add a new for the sd_combo type
dt-bindings: mmc: sdhci-msm: constrain reg-names per variants
dt-bindings: mmc: sdhci-msm: fix reg-names entries
dt-bindings: mmc: Add compatible for MediaTek MT8188
dt-bindings: mmc: sdhci-msm: document resets
mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
This KUnit update for Linux 5.20-rc1 consists of several fixes and an
important feature to discourage running KUnit tests on production
systems. Running tests on a production system could leave the system
in a bad state. This new feature adds:
- adds a new taint type, TAINT_TEST to signal that a test has been run.
This should discourage people from running these tests on production
systems, and to make it easier to tell if tests have been run
accidentally (by loading the wrong configuration, etc.)
- several documentation and tool enhancements and fixes.
-----BEGIN PGP SIGNATURE-----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=WzBX
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit updates from Shuah Khan:
"This consists of several fixes and an important feature to discourage
running KUnit tests on production systems. Running tests on a
production system could leave the system in a bad state.
Summary:
- Add a new taint type, TAINT_TEST to signal that a test has been
run.
This should discourage people from running these tests on
production systems, and to make it easier to tell if tests have
been run accidentally (by loading the wrong configuration, etc)
- Several documentation and tool enhancements and fixes"
* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
Documentation: KUnit: Fix example with compilation error
Documentation: kunit: Add CLI args for kunit_tool
kcsan: test: Add a .kunitconfig to run KCSAN tests
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
nitro_enclaves: test: Use kunit_test_suite() macro
thunderbolt: test: Use kunit_test_suite() macro
kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
kunit: unify module and builtin suite definitions
selftest: Taint kernel when test module loaded
module: panic: Taint the kernel when selftest modules load
Documentation: kunit: fix example run_kunit func to allow spaces in args
Documentation: kunit: Cleanup run_wrapper, fix x-ref
kunit: test.h: fix a kernel-doc markup
kunit: tool: Enable virtio/PCI by default on UML
kunit: tool: make --kunitconfig repeatable, blindly concat
kunit: add coverage_uml.config to enable GCOV on UML
kunit: tool: refactor internal kconfig handling, allow overriding
kunit: tool: introduce --qemu_args
...
-----BEGIN PGP SIGNATURE-----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=celk
-----END PGP SIGNATURE-----
Merge tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Improve the type checking of request flags (Bart)
- Ensure queue mapping for a single queues always picks the right queue
(Bart)
- Sanitize the io priority handling (Jan)
- rq-qos race fix (Jinke)
- Reserved tags handling improvements (John)
- Separate memory alignment from file/disk offset aligment for O_DIRECT
(Keith)
- Add new ublk driver, userspace block driver using io_uring for
communication with the userspace backend (Ming)
- Use try_cmpxchg() to cleanup the code in various spots (Uros)
- Finally remove bdevname() (Christoph)
- Clean up the zoned device handling (Christoph)
- Clean up independent access range support (Christoph)
- Clean up and improve block sysfs handling (Christoph)
- Clean up and improve teardown of block devices.
This turns the usual two step process into something that is simpler
to implement and handle in block drivers (Christoph)
- Clean up chunk size handling (Christoph)
- Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
Ming, Sebastian, Yang, Ying)
* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
ublk_drv: fix double shift bug
ublk_drv: make sure that correct flags(features) returned to userspace
ublk_drv: fix error handling of ublk_add_dev
ublk_drv: fix lockdep warning
block: remove __blk_get_queue
block: call blk_mq_exit_queue from disk_release for never added disks
blk-mq: fix error handling in __blk_mq_alloc_disk
ublk: defer disk allocation
ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
ublk: cleanup ublk_ctrl_uring_cmd
ublk: simplify ublk_ch_open and ublk_ch_release
ublk: remove the empty open and release block device operations
ublk: remove UBLK_IO_F_PREFLUSH
ublk: add a MAINTAINERS entry
block: don't allow the same type rq_qos add more than once
mmc: fix disk/queue leak in case of adding disk failure
ublk_drv: fix an IS_ERR() vs NULL check
ublk: remove UBLK_IO_F_INTEGRITY
ublk_drv: remove unneeded semicolon
...
Merge ACPI device object management changes for v5.20-rc1.
- Use the facilities provided by the driver core and some additional
helpers to handle the children of a given ACPI device object in
multiple places instead of using the children and node list heads in
struct acpi_device which is error prone (Rafael Wysocki).
- Fix ACPI-related device reference counting issue in the hisi_lpc bus
driver (Yang Yingliang).
- Drop the children and node list heads that are not needed any more
from struct acpi_device (Rafael Wysocki).
- Drop driver member from struct acpi_device (Uwe Kleine-König).
- Drop redundant check from acpi_device_remove() (Uwe Kleine-König).
* acpi-bus:
ACPI: bus: Drop unused list heads from struct acpi_device
hisi_lpc: Use acpi_dev_for_each_child()
bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
ACPI: bus: Drop driver member of struct acpi_device
ACPI: bus: Drop redundant check in acpi_device_remove()
mfd: core: Use acpi_dev_for_each_child()
ACPI / MMC: PM: Unify fixing up device power
soundwire: Use acpi_dev_for_each_child()
platform/x86/thinkpad_acpi: Use acpi_dev_for_each_child()
ACPI: scan: Walk ACPI device's children using driver core
ACPI: bus: Introduce acpi_dev_for_each_child_reverse()
ACPI: video: Use acpi_dev_for_each_child()
ACPI: bus: Export acpi_dev_for_each_child() to modules
ACPI: property: Use acpi_dev_for_each_child() for child lookup
ACPI: container: Use acpi_dev_for_each_child()
USB: ACPI: Replace usb_acpi_find_port() with acpi_find_child_by_adr()
thunderbolt: ACPI: Replace tb_acpi_find_port() with acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_dev_has_children()
ACPI: glue: Use acpi_dev_for_each_child()
Add support for eint IRQ when MSDC is used as an SDIO host. This
feature requires SDIO device support async IRQ function. With this
feature, SDIO host can be awakened by SDIO card in suspend state,
without additional pin.
MSDC driver will time-share the SDIO DAT1 pin. During suspend, MSDC
turn off clock and switch SDIO DAT1 pin to GPIO mode. And during
resume, switch GPIO function back to DAT1 mode then turn on clock.
Some device tree property should be added or modified in MSDC node
to support SDIO eint IRQ. Pinctrls "state_eint" is mandatory. Since
this feature depends on asynchronous interrupts, "wakeup-source",
"keep-power-in-suspend" and "cap-sdio-irq" flags are necessary, and
the interrupts list should be extended(the interrupt named with
sdio_wakeup):
&mmcX {
...
interrupt-names = "msdc", "sdio_wakeup";
interrupts-extended = <...>,
<&pio xxx IRQ_TYPE_LEVEL_LOW>;
...
pinctrl-names = "default", "state_uhs", "state_eint";
...
pinctrl-2 = <&mmc2_pins_eint>;
...
cap-sdio-irq;
keep-power-in-suspend;
wakeup-source;
...
};
Co-developed-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-4-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If wakeup-source flag is set in host dts node, parse EAI information
from SDIO CCCR interrupt externsion segment for in-band wakeup. If
async interrupt is supported by SDIO card then enable it and set
enable_async_irq flag in sdio_cccr structure to 1. The parse flow is
implemented in sdio_read_cccr().
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-3-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newest Gen3 SoCs and Gen4 SoCs do not need manual tap correction
with HS400 anymore. So, instead of checking the SDHI version, add a
quirk flag and set manual tap correction only for affected SoCs.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased, renamed the quirk variable, removed stale comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220720072901.1266-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In thunder_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 166bac38c3 ("mmc: cavium: Add MMC PCI driver for ThunderX SOCs")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-2-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In octeon_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 01d9584333 ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_fixup_of_compatible_match(), we should call of_node_put()
when breaking out of for_each_child_of_node() which will increase
and decrease the refcount during one iteration.
Fixes: b360b11026 ("mmc: core: allow to match the device tree to apply quirks")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220719091051.1210806-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use clk_get_rate for base_clk on resume before setting new rate.
This change ensures that the clock api returns current rate
and sets the clock to the desired rate and honors CLK_GET_NO_CACHE
attribute used by clock api.
Fixes: 97904a5985 (mmc: sdhci-brcmstb: Add ability to increase max clock rate for 72116b0)
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220714174132.18541-1-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts three commits:
1. Revert "mmc: sdhci-msm: Add compatible string check for sdx65"
This reverts commit 953706844f.
2. Revert "mmc: sdhci-msm: Add compatible string check for sm8150"
This reverts commit 5acd6adb65.
3. Revert "mmc: sdhci-msm: Add SoC specific compatibles"
This reverts commit 466614a976.
The oldest commit 466614a976 ("mmc: sdhci-msm: Add SoC specific
compatibles") did not specify what benefits such multiple compatibles
bring, therefore assume there is none. On the other hand such approach
brings a lot of churn to driver maintenance by expecting commit for
every new compatible, even though it is already covered by the fallback.
There is really no sense in duplicating of_device_id for each
variant, which is already covered by generic compatible fallback
qcom,sdhci-msm-v4 or qcom,sdhci-msm-v5.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220714091042.22287-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cards with 4k native sector size may only be read 4k-aligned,
accommodate for this in the single read recovery and use it.
Fixes: 81196976ed (mmc: block: Add blk-mq support)
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/cf4f316274c5474586d0d99b17db4a4c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v5.19rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v5.20.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add mmc_card_sd_combo() macro for sd combo type card and use the mmc_card_*
macro to simplify code instead of comparing card->type.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20220713033635.28432-2-sh043.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need runtime PM enabled early in probe before sdhci_setup_host() for
sdhci_omap_set_capabilities(). But on the first runtime resume we must
not call sdhci_runtime_resume_host() as sdhci_setup_host() has not been
called yet. Let's check for an initialized controller like we already do
for context restore to fix a lockdep warning.
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220622051215.34063-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In set_uhs_signaling, the DDR bit is being set by fully writing the MC1R
register.
This can lead to accidental erase of certain bits in this register.
Avoid this by doing a read-modify-write operation.
Fixes: d0918764c1 ("mmc: sdhci-of-at91: fix MMC_DDR_52 timing selection")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Karl Olsen <karl@micro-technic.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220630090926.15061-1-eugen.hristev@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD_ROCR_S18A is already defined and is used to check the rocr value, so
let's replace with already defined values for readability.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220706004840.24812-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we reset because of an error, we need to preserve values for the
clock frequency. Otherwise, glitches may be seen on the bus.
To achieve that, we introduce a 'preserve' parameter to the reset
function and the IP core specific reset callbacks to handle everything
accordingly.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220625131722.1397-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix typo's,
* difference -> different
* alignment -> aligned
While at it updated the comment to make it clear that Renesas SDHI DMAC
needs buffers to be 128-byte aligned.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of devm_reset_control_get_optional_exclusive() failure we returned
directly instead of jumping to the error path to roll back initialization.
This patch moves devm_reset_control_get_optional_exclusive() early in the
probe so that we have the reset handle prior to initialization of the
hardware.
Fixes: b4d86f37ea ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Callers of of_find_compatible_node() should drop the reference count
accordingly, so let's do that.
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220621065259.4079817-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If CONFIG_PM is not set.
make ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-, will be failed, like this:
drivers/mmc/host/sdhci-pci-gli.c:834:13: error: ‘gl9763e_set_low_power_negotiation’ defined but not used [-Werror=unused-function]
static void gl9763e_set_low_power_negotiation(struct sdhci_pci_slot *slot, bool enable)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[3]: *** [drivers/mmc/host/sdhci-pci-gli.o] Error 1
To fix building warning, wrap all related code with CONFIG_PM.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220619104712.125364-1-renzhijie2@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to flaws in hardware design, GL9763E takes long time to exit from L1
state. The I/O performance will suffer severe impact if it often enter and
exit L1 state during I/O requests.
To improve I/O read/write performance and take battery life into account,
let's turn on GL9763E L1 negotiation before entering runtime suspend and
turn off GL9763E L1 negotiation while executing runtime resume. That is to
say, GL9763E will not enter L1 state when executing I/O requests and enter
L1 state when PCIe bus idle.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20220613092907.2502-1-jason.lai@genesyslogic.com.tw
[Ulf: Improved the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns a few times along the lines of:
drivers/mmc/host/sdhci-brcmstb.c:302:6: warning: variable 'base_clk' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (res)
^~~
drivers/mmc/host/sdhci-brcmstb.c:376:24: note: uninitialized use occurs here
clk_disable_unprepare(base_clk);
^~~~~~~~
base_clk is used in the error path before it is initialized. Initialize
it to NULL, as clk_disable_unprepare() calls clk_disable() and
clk_unprepare(), which both handle NULL pointers gracefully.
Link: https://github.com/ClangBuiltLinux/linux/issues/1650
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220608152757.82529-1-nathan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220608090152.179395-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-6-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add debug fs entry error state to query eMMC and SD card errors statistics.
If any errors occurred in eMMC and SD card driver level then
err_state value will be set to 1.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-5-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-3-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-2-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/mmc/host/mxcmmc.c:1028:18: warning: cast to smaller integer type 'enum mxcmci_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 8223e885e7 ("mmc: mxc: Convert the driver to DT-only")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20220526010022.1163483-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() checks null pointer.
Fixes: ea35645a3c ("mmc: sdhci-of-esdhc: add support for signal voltage switch")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220523144255.10310-1-linmq006@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 72116B0 has improved SDIO controllers that allow the max clock
rate to be increased from a max of 100MHz to a max of 150MHz. The
driver will need to get the clock and increase it's default rate
and override the caps register, that still indicates a max of 100MHz.
The new clock will be named "sdio_freq" in the DT node's "clock-names"
list. The driver will use a DT property, "clock-frequency", to
enable this functionality and will get the actual rate in MHz
from the property to allow various speeds to be requested.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220520183108.47358-3-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for RK3588's DWCMSHC controller, which is used for
providing the rootfs on the RK3588 evaluation board.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
[port from vendor BSP]
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220504213251.264819-12-sebastian.reichel@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Prepare driver for rk3588 support by renaming the internal data
structures.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220504213251.264819-11-sebastian.reichel@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The reset function build in the SDHCI will not reset the logic
circuit related to the tuning function, which may cause data
reading errors. Resetting the complete SDHCI controller through
the reset controller fixes the issue.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
[rebase, use optional variant of reset getter]
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220504213251.264819-10-sebastian.reichel@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The kunit_test_suite() macro is no-longer incompatible with module_add,
so its use can be reinstated.
Since this fixes parsing with builtins and kunit_tool, also enable the
test by default when KUNIT_ALL_TESTS is enabled.
The test can now be run via kunit_tool with:
./tools/testing/kunit/kunit.py run --arch=x86_64 \
--kconfig_add CONFIG_OF=y --kconfig_add CONFIG_OF_ADDRESS=y \
--kconfig_add CONFIG_MMC=y --kconfig_add CONFIG_MMC_SDHCI=y \
--kconfig_add CONFIG_MMC_SDHCI_PLTFM=y \
--kconfig_add CONFIG_MMC_SDHCI_OF_ASPEED=y \
'sdhci-of-aspeed'
(It may be worth adding a .kunitconfig at some point, as there are
enough dependencies to make that command scarily long.)
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
With new API blk_mq_is_reserved_rq() we can tell if a request is from
the reserved pool, so stop passing 'reserved' arg. There is actually
only a single user of that arg for all the callback implementations, which
can use blk_mq_is_reserved_rq() instead.
This will also allow us to stop passing the same 'reserved' around the
blk-mq iter functions next.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/1657109034-206040-4-git-send-email-john.garry@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set the queue dying flag and call blk_mq_exit_queue from del_gendisk for
all disks that do not have separately allocated queues, and thus remove
the need to call blk_cleanup_queue for them.
Rename blk_cleanup_disk to blk_mq_destroy_queue to make it clear that
this function is intended only for separately allocated blk-mq queues.
This saves an extra queue freeze for devices without a separately
allocated queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20220619060552.1850436-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce acpi_device_fix_up_power_extended() for fixing up power of
a device having an ACPI companion in a manner that takes the device's
children into account and make the MMC code use it in two places
instead of walking the list of the device ACPI companion's children
directly.
This will help to eliminate the children list head from struct
acpi_device as it is redundant and it is used in questionable ways
in some places (in particular, locking is needed for walking the
list pointed to it safely, but it is often missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
MediaTek IP requires that after dma stop, it need to wait this dma stop
bit auto-reset to 0. When bus is in high loading state, it will take a
while for the dma stop complete. If there is no waiting operation here,
when program runs to clear fifo and reset, bus will hang.
In addition, there should be no return in msdc_data_xfer_next() if
there is data need be transferred, because no matter what error occurs
here, it should continue to excute to the following mmc_request_done.
Otherwise the core layer may wait complete forever.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220609112239.18911-1-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The result from ->get_cd() may be incorrect as the card detect debouncing
isn't managed correctly. Let's fix it.
Signed-off-by: Chevron Li<chevron.li@bayhubtech.com>
Fixes: 7d44061704 ("mmc: sdhci-pci-o2micro: Fix O2 Host data read/write DLL Lock phase shift issue")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220602132543.596-1-chevron.li@bayhubtech.com
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
The intention of the use of mmc_blk_reset_success() in
mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and
getting the same error. However, that may not be the case - any amount
of time and I/O may pass before another recovery is needed, in which
case there would be no reason to deny it the opportunity to recover via
a reset if necessary. CQE recovery is expected seldom and failure to
recover (if the clear tasks command fails), even more seldom, so it is
better to allow the reset always, which can be done by calling
mmc_blk_reset_success() always.
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220531171922.76080-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the system resumes from suspend (S3 or S4), the power mode is
MMC_POWER_OFF. In this status, gl9763e_runtime_resume() should not enable
PLL. Add a condition to this function to enable PLL only when the power
mode is MMC_POWER_ON.
Fixes: d607667bb8 (mmc: sdhci-pci-gli: Add runtime PM for GL9763E)
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220520114242.150235-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
. correctly set up ZERO_PAGE pointer
. drop ISA_DMA_API support
. fix comment typos
. fixes for undefined symbols
. remove unused code and variables
. elf-fdpic loader support for m68k
-----BEGIN PGP SIGNATURE-----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=O3zh
-----END PGP SIGNATURE-----
Merge tag 'm68knommu-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"A collection of changes to add elf-fdpic loader support for m68k.
Also a collection of various fixes. They include typo corrections,
undefined symbol compilation fixes, removal of the ISA_DMA_API support
and removal of unused code.
Summary:
- correctly set up ZERO_PAGE pointer
- drop ISA_DMA_API support
- fix comment typos
- fixes for undefined symbols
- remove unused code and variables
- elf-fdpic loader support for m68k"
* tag 'm68knommu-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 68000 CPU link with no platform selected
m68k: removed unused "mach_get_ss"
m68knommu: fix undefined reference to `mach_get_rtc_pll'
m68knommu: fix undefined reference to `_init_sp'
m68knommu: allow elf_fdpic loader to be selected
m68knommu: add definitions to support elf_fdpic program loader
m68knommu: implement minimal regset support
m68knommu: use asm-generic/mmu.h for nommu setups
m68k: fix typos in comments
m68k: coldfire: drop ISA_DMA_API support
m68knommu: set ZERO_PAGE() to the allocated zeroed page
Not much dramatic changes at this time, but we've received quite
a lot of changes for ASoC, while there are still a few fixes and
quirks for usual HD- and USB-auido. Here are some highlights.
* ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
* Others
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmKOEiAOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE96FxAAnoVCecFK955fWInCULe15xYpi9kqngDSLAQk
k6TkbP8AFyX+3PbIb9YVK9u+fLBaZzdK/ZIRqZNfb5T4q8tVTHphg2P+SNB36qaD
nTTaEQ6dr6VUJO3fwwVBa3NJ+rGPr8KMKLlQGCg/I8HKdFeW2t/mV1YZI/ZxM7Or
MXu3F5dt3yVXXMgUb33if+atYCXOwJ9YIqe1WHE4oPTtfOhbwiIdFeHgg88Kq7vJ
ep7PCbyJ0rqfA9BIAnBfQuD9ZoaS7mKlo9xgyauNBzWnbRVd7dYyUnaxH++XLPPS
GS0MEgftJfmUay6o++I7qrhoTyMKMHN/CU+6RlR1GD6WBpBhQ6T+poLkFDvKqbL8
kvFEBFrEf0soeAKkUinzl1wCJnzWvpq2PF0EewQp03A3vOL5MOzGdId1wLKLmbCw
Z0e0HAKTP4/AQeBluLo/SjiNoeSEU76xYYv8tFGv531ybIhvsF0nm/Suv4VZcy0V
9tr2gLSORDLTBqSJqCf1JgN8oJht0QLirzgSekk8HUvx1JnIwwAaH1Dvy1DMrjyu
TQ6oRyDS2giHKh7FItv3+U+HE1CkA89dzDvGrIbKrT6xkodHGzLNr0DxaDGuR11w
H9f9oFEnGBpBxWmfLkGTa8+oBenTz8YRm4Ti8xhZkJkD1ys/4fjasAYoIKJqdnxH
iG1DWic=
=5qBk
-----END PGP SIGNATURE-----
Merge tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Not much dramatic changes at this time, but we've received quite a lot
of changes for ASoC, while there are still a few fixes and quirks for
usual HD- and USB-auido. Here are some highlights.
ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Others:
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver"
* tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (504 commits)
ALSA: hda/realtek - Add new type for ALC245
ALSA: usb-audio: Configure sync endpoints before data
ALSA: ctxfi: fix typo in comment
ALSA: cs5535audio: fix typo in comment
ALSA: ctxfi: Add SB046x PCI ID
ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
ALSA: usb-audio: Workaround for clock setup on TEAC devices
ALSA: lola: Bounds check loop iterator against streams array size
ASoC: max98090: Move check for invalid values before casting in max98090_put_enab_tlv()
ASoC: rt1308-sdw: add the default value of register 0xc320
ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic
ASoC: rt9120: Fix 3byte read, valule offset typo
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver.
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver
ASoC: wm2000: fix missing clk_disable_unprepare() on error in wm2000_anc_transition()
ASoC: codecs: lpass: Fix passing zero to 'PTR_ERR'
ASoC: SOF: sof-client-ipc-flood-test: use pm_runtime_resume_and_get()
ASoC: SOF: mediatek: remove duplicate include in mt8195.c
ASoC: SOF: mediatek: Add mt8195 debug dump
ASoC: SOF: mediatek: Add mediatek common debug dump
...
- Support zero-out using TRIM for eMMC
- Allow to override the busy-timeout for the ioctl-cmds
MMC host:
- Continued the conversion of DT bindings into the JSON schema
- jz4740: Apply DMA engine limits to maximum segment size
- mmci_stm32: Use a buffer for unaligned DMA requests
- mmc_spi: Enabled high-speed modes via parsing of DT
- omap: Make clock management to be compliant with CCF
- renesas_sdhi: Support eMMC HS400 mode for R-Car V3H ES2.0
- renesas_sdhi: Don't allow support for eMMC HS400 for R-Car V3M/D3
- sdhci_am654: Fix problem when SD card slot lacks the card detect line
- sdhci-esdhc-imx: Add support for the imx8dxl variant
- sdhci-brcmstb: Enable support for clock gating to save power
- sdhci-msm: Add support for the sdx65 variant
- sdhci-msm: Add support for the sm8150 variant
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-pci-gli: Add workaround to allow GL9755 to enter ASPM L1.2
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAmKLelkXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCk+Lg/8Ck1m60yrij05TD4qmLTdodBi
8qR4bfxHyfQrtz2k6+Uy7nJFtYqr4+YVgiyUUSfiptofIBciT8gn3lrWXmt5+ZKU
ATpz2n40DmPHF54ngBCplIUc22+4toTEoHbwpQmHivUWeLQQPHfTsl3dIBkP0ElV
DCL/JMMnRxaCRxzu+DSF8zg10QJJ53K6MQki0O8RQPsDiV39Tz2+nt1R7PKpTufe
FFn8pSuBtj3rbDFIMczFjw5HZqCvl3a+9Bp/YDs2IF4Wv+YRYSLVb0nwfh+ehBrz
4sKzMGANQr35QPupbKc1BJUGy8/+QHsY/iq10xh36cbix/Qn7KIpRfsybhgLILh/
VJmT8M2fA7i2jEuQfnMUlQ7BOmtsGd+b1LFZqZ2UrXUyfcwLKOdIh2B6D4SDLBvQ
9CohhhTsIlxN2bGjUb25QEu0ipa8DNZYWkVZB1DEoWhC3f5WQjkoe6+D3L+Jz7rE
Apfk6D5lj/sCUIZd+JyTghMRp1ZWzeDHV8umzDlTUl+YKkqtQ5udsGal288lAJen
T3+0Kvm9rpbIZckoQQ/we2rtvNH7UiOZh5ldgVJ11tHNdRoCo2qanpQYB5QDCTPD
gFpD+KHxZqcjRKVkZWMNfo1tdTJu81y6w2WiQ+W7QXnfo0OdYFTqBIDjTF9uDumA
sLTpaaMrYaCrEcbTrAw=
=eAYF
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Support zero-out using TRIM for eMMC
- Allow to override the busy-timeout for the ioctl-cmds
MMC host:
- Continued the conversion of DT bindings into the JSON schema
- jz4740: Apply DMA engine limits to maximum segment size
- mmci_stm32: Use a buffer for unaligned DMA requests
- mmc_spi: Enabled high-speed modes via parsing of DT
- omap: Make clock management to be compliant with CCF
- renesas_sdhi:
- Support eMMC HS400 mode for R-Car V3H ES2.0
- Don't allow support for eMMC HS400 for R-Car V3M/D3
- sdhci_am654: Fix problem when SD card slot lacks the card detect
line
- sdhci-esdhc-imx: Add support for the imx8dxl variant
- sdhci-brcmstb: Enable support for clock gating to save power
- sdhci-msm:
- Add support for the sdx65 variant
- Add support for the sm8150 variant
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-pci-gli: Add workaround to allow GL9755 to enter ASPM L1.2"
* tag 'mmc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci-of-arasan: Add NULL check for data field
mmc: core: Support zeroout using TRIM for eMMC
mmc: sdhci-brcmstb: Fix compiler warning
mmc: sdhci-msm: Add compatible string check for sdx65
dt-bindings: mmc: sdhci-msm: Document the SDX65 compatible
mmc: sdhci-msm: Add compatible string check for sm8150
dt-bindings: mmc: sdhci-msm: Add compatible string for sm8150
mmc: sdhci-msm: Add SoC specific compatibles
dt-bindings: mmc: sdhci-msm: Convert bindings to yaml
dt-bindings: mmc: brcm,sdhci-brcmstb: cleanup example
dt-bindings: mmc: brcm,sdhci-brcmstb: correct number of reg entries
mmc: sdhci-brcmstb: Enable Clock Gating to save power
mmc: sdhci-brcmstb: Re-organize flags
mmc: mmci: Remove custom ios handler
mmc: atmel-mci: Simplify if(chan) and if(!chan)
mmc: core: use kobj_to_dev()
dt-bindings: mmc: sdhci-of-dwcmhsc: Add rk3588
mmc: core: Add CIDs for cards to the entropy pool
mmc: core: Allows to override the timeout value for ioctl() path
mmc: sdhci-omap: Use of_device_get_match_data() helper
...
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmKKrUsQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpgDjD/44hY9h0JsOLoRH1IvFtuaH6n718JXuqG17
hHCfmnAUVqj2jT00IUbVlUTd905bCGpfrodBL3PAmPev1zZHOUd/MnJKrSynJ+/s
NJEMZQaHxLmocNDpJ1sZo7UbAFErsZXB0gVYUO8cH2bFYNu84H1mhRCOReYyqmvQ
aIAASX5qRB/ciBQCivzAJl2jTdn4WOn5hWi9RLidQB7kSbaXGPmgKAuN88WI4H7A
zQgAkEl2EEquyMI5tV1uquS7engJaC/4PsenF0S9iTyrhJLjneczJBJZKMLeMR8d
sOm6sKJdpkrfYDyaA4PIkgmLoEGTtwGpqGHl4iXTyinUAxJoca5tmPvBb3wp66GE
2Mr7pumxc1yJID2VHbsERXlOAX3aZNCowx2gum2MTRIO8g11Eu3aaVn2kv37MBJ2
4R2a/cJFl5zj9M8536cG+Yqpy0DDVCCQKUIqEupgEu1dyfpznyWH5BTAHXi1E8td
nxUin7uXdD0AJkaR0m04McjS/Bcmc1dc6I8xvkdUFYBqYCZWpKOTiEpIBlHg0XJA
sxdngyz5lSYTGVA4o4QCrdR0Tx1n36A1IYFuQj0wzxBJYZ02jEZuII/A3dd+8hiv
EY+VeUQeVIXFFuOcY+e0ScPpn7Nr17hAd1en/j2Hcoe4ZE8plqG2QTcnwgflcbis
iomvJ4yk0Q==
=0Rw1
-----END PGP SIGNATURE-----
Merge tag 'for-5.19/block-2022-05-22' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Here are the core block changes for 5.19. This contains:
- blk-throttle accounting fix (Laibin)
- Series removing redundant assignments (Michal)
- Expose bio cache via the bio_set, so that DM can use it (Mike)
- Finish off the bio allocation interface cleanups by dealing with
the weirdest member of the family. bio_kmalloc combines a kmalloc
for the bio and bio_vecs with a hidden bio_init call and magic
cleanup semantics (Christoph)
- Clean up the block layer API so that APIs consumed by file systems
are (almost) only struct block_device based, so that file systems
don't have to poke into block layer internals like the
request_queue (Christoph)
- Clean up the blk_execute_rq* API (Christoph)
- Clean up various lose end in the blk-cgroup code to make it easier
to follow in preparation of reworking the blkcg assignment for bios
(Christoph)
- Fix use-after-free issues in BFQ when processes with merged queues
get moved to different cgroups (Jan)
- BFQ fixes (Jan)
- Various fixes and cleanups (Bart, Chengming, Fanjun, Julia, Ming,
Wolfgang, me)"
* tag 'for-5.19/block-2022-05-22' of git://git.kernel.dk/linux-block: (83 commits)
blk-mq: fix typo in comment
bfq: Remove bfq_requeue_request_body()
bfq: Remove superfluous conversion from RQ_BIC()
bfq: Allow current waker to defend against a tentative one
bfq: Relax waker detection for shared queues
blk-cgroup: delete rcu_read_lock_held() WARN_ON_ONCE()
blk-throttle: Set BIO_THROTTLED when bio has been throttled
blk-cgroup: Remove unnecessary rcu_read_lock/unlock()
blk-cgroup: always terminate io.stat lines
block, bfq: make bfq_has_work() more accurate
block, bfq: protect 'bfqd->queued' by 'bfqd->lock'
block: cleanup the VM accounting in submit_bio
block: Fix the bio.bi_opf comment
block: reorder the REQ_ flags
blk-iocost: combine local_stat and desc_stat to stat
block: improve the error message from bio_check_eod
block: allow passing a NULL bdev to bio_alloc_clone/bio_init_clone
block: remove superfluous calls to blkcg_bio_issue_init
kthread: unexport kthread_blkcg
blk-cgroup: cleanup blkcg_maybe_throttle_current
...
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLf5EACgkQJNaLcl1U
h9ASqAf/YnwbFP919ree/DEKUDCNc4klUH5M4JOexXbZlZDqxKYRGZjoLuiwX/PQ
Au/xOjGEvm3Yg5/g5c8YFVNcIkv1O8VclRkV59oIxlBwKmQeTKvq+lOmlel2l1wZ
XOmvHjE46wxH1N1cLwL6KkX0YDn59orSZGYZRpfLjL61y6LQWsLNU0tY6AWCRATB
Llnrbu+DYgCsYNTEOOOY5s4V+4LkQm8TLdft91Va7mBdkPPRFoXRO0HGcVBqbkoN
7pf2mrjrLAWL9yuA8FlrgJbHq58DF9WGe5uEU7qlVL1zw46ClgIM0ABxPOdNdjV2
Wzb1jI7GmztgQNxlR9BcJB0kxAj9vA==
=oD5l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.19
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
It turned out that polling period for MMC_SEND_OP_COND, that currently is
set to 1ms, still isn't sufficient. In particular a Micron eMMC on a
Beaglebone platform, is reported to sometimes fail to initialize.
Additional test, shows that extending the period to 4ms is working fine, so
let's make that change.
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Tested-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Fixes: 1760fdb6fe (mmc: core: Restore (almost) the busy polling for MMC_SEND_OP_COND")
Fixes: 76bfc7ccc2 ("mmc: core: adjust polling interval for CMD1")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220517101046.27512-1-ulf.hansson@linaro.org
Add NULL check for data field retrieved from of_device_get_match_data()
before dereferencing the data.
Addresses-coverity: CID 305057:Dereference null return value (NULL_RETURNS)
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1652339993-27280-1-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After a build regression report, I took a look at possible users of
CONFIG_ISA_DMA_API on m68k and found none, which Greg confirmed. The
CONFIG_GENERIC_ISA_DMA option in turn is only needed to implement
ISA_DMA_API, and is clearly not used on the platforms with ISA support.
The CONFIG_ISA support for AMIGA_PCMCIA is probably also unneeded,
but this is less clear. Unlike other PCMCIA implementations, this one
does not use the drivers/pcmcia subsystem at all and just supports
the "apne" network driver. When it was first added, one could use
ISA drivers on it as well, but this probably broke at some point.
With no reason to keep this, let's just drop the corresponding files
and prevent the remaining ISA drivers that use this from getting built.
The remaining definitions in asm/dma.h are used for PCI support.
Link: https://lore.kernel.org/lkml/9e5ee1c3-ca80-f343-a1f5-66f3dd1c0727@linux-m68k.org/
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
If an eMMC card supports TRIM and indicates that it erases to zeros, we can
use it to support hardware offloading of REQ_OP_WRITE_ZEROES, so let's add
support for this.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Link: https://lore.kernel.org/r/20220429152118.3617303-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since Qualcomm device-trees already use SoC specific compatibles for
describing the 'sdhci-msm' nodes, it makes sense to add the support for the
same in the driver as well.
Keep the old deprecated compatible strings still in the driver, to ensure
backward compatibility with older device-trees.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20220429220833.873672-3-bhupesh.sharma@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enabling this feature will allow the controller to stop the bus
clock when the bus is idle. The feature is not part of the standard
and is unique to newer Arasan cores and is enabled with a bit in a
vendor specific register. This feature will only be enabled for
non-removable devices because they don't switch the voltage and
clock gating breaks SD Card volatge switching.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220427180853.35970-3-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-organize the flags by basing the bit names on the flag that they
apply to. Also change the "flags" member in the "brcmstb_match_priv"
struct to const.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220427180853.35970-2-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer variants of the MMC controller support a 34-bit physical address
space by using word addresses instead of byte addresses. However, the
code truncates the DMA descriptor address to 32 bits before applying the
shift. This breaks DMA for descriptors allocated above the 32-bit limit.
Fixes: 3536b82e58 ("mmc: sunxi: add support for A100 mmc controller")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220424231751.32053-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make the entropy pool a bit better we can toss in the
CID for eMMC and SD cards into it, usually the serial
number portion is at least unique.
This does not count as improvement of the entropy but
in practice it makes it a bit more random to mix in these
numbers.
Cc: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220425205442.1347837-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Occasionally, user-land applications initiate longer timeout values for certain commands
through ioctl() system call. But so far we are still using a fixed timeout of 10 seconds
in mmc_poll_for_busy() on the ioctl() path, even if a custom timeout is specified in the
userspace application. This patch allows custom timeout values to override this default
timeout values on the ioctl path.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220423221623.1074556-3-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only the device data is needed, not the entire struct of_device_id.
Use of_device_get_match_data() instead of open coding of_match_device().
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20220423221623.1074556-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning. Similar to the issue pointed
out in sdhci-of-arasan.c driver, commit 3794c54264 ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220425063120.10135-3-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We iterate an extra time through the IRQ status handling
loop despite nothing had fired. Enabling the debug prints:
mmci-pl18x 80005000.mmc: op 01 arg 00000000 flags 000000e1
mmci-pl18x 80005000.mmc: irq0 (data+cmd) 00000001
mmci-pl18x 80005000.mmc: irq0 (data+cmd) 00000000
mmci-pl18x 80005000.mmc: op 01 arg 40ff8080 flags 000000e1
mmci-pl18x 80005000.mmc: irq0 (data+cmd) 00000001
mmci-pl18x 80005000.mmc: irq0 (data+cmd) 00000000
It is pointless to loop through the function when status
is zero. Just break the loop if the status is zero.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220416224549.627623-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When GL9755 enters ASPM L1 sub-states, it will stay at L1.1 and will not
enter L1.2. The workaround is to toggle PM state to allow GL9755 to enter
ASPM L1.2.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220414094945.457500-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have a dedicated directory for platform_data meanwhile, don't spoil
the MMC directory with it.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220412093102.3428-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make it unambiguous that the hw_reset callback is for cards and not
for controllers, we add 'card' to the callback name and convert all
users in one go. We keep the argument as mmc_host, though, because the
callback is used very early when mmc_card is not yet populated.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220408080045.6497-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make it unambiguous that mmc_sw_reset() is for cards and not for
controllers, we make the function argument mmc_card instead of mmc_host.
There are no users to convert currently.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220408080045.6497-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need to specify the Gen3 compatible entry for M3W because it
will be provided by the generic Gen3 fallback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220404130551.20209-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware evolved, so we only need to disable HS400 support on ES1.*
revisions. Update the code.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: refactored to top-of-tree]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220404123404.16289-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver, OMAP specific, now omits clk_prepare/unprepare() steps, not
supported by OMAP custom implementation of clock API. However, non-CCF
stubs of those functions exist for use on such platforms until converted
to CCF.
Update the driver to be compatible with CCF implementation of clock API.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Link: https://lore.kernel.org/r/20220402112004.129886-1-jmkrzyszt@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since SD and MMC Highspeed modes are also valid for SPI let's parse
them too.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20c6efa9a4c7423bbfb9352705c4a53a@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Despite mmc_ioc_multi_cmd::num_of_cmds is a 64-bit field, its maximum
value is limited to MMC_IOC_MAX_CMDS (only 255); using a 64-bit local
variable to hold a copy of that field leads to gcc generating ineffective
loop code: despite the source code using an *int* variable for the loop
counters, the 32-bit object code uses 64-bit unsigned counters. Also,
gcc has to drop the most significant word of that 64-bit variable when
calling kcalloc() and assigning to mmc_queue_req::ioc_count anyway.
Using the *unsigned int* variable instead results in a better code.
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/eea3b0bd-6091-f005-7189-b5b7868abdb6@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Further digging in the datasheets revealed that R-Car V3M also has no
HS400 support.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220404105831.5096-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running on an system without any quirks (e.g. R-Car V3U), the
kernel crashes with a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002
...
Hardware name: Renesas Falcon CPU and Breakout boards based on r8a779a0 (DT)
Workqueue: events_freezable mmc_rescan
...
Call trace:
renesas_sdhi_internal_dmac_start_dma+0x54/0x12c
tmio_process_mrq+0x124/0x274
Fix this by adding the missing checks for the validatity of the
priv->quirks pointer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/cc3178c2ff60f640f4d5a071d51f6b0b1db37656.1648822020.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In SDIO mode, the sg list for requests can be unaligned with what the
STM32 SDMMC internal DMA can support. In that case, instead of failing,
use a temporary bounce buffer to copy from/to the sg list.
This buffer is limited to 1MB. But for that we need to also limit
max_req_size to 1MB. It has not shown any throughput penalties for
SD-cards or eMMC.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20220328145114.334577-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After Shimoda-san's much appreciated refactoring of the quirk handling,
we can convert now 'dmac_only_one_rx' from an ugly global flag to a
regular quirk. This makes quirk handling more consistent and easier to
maintain. After this patch, soc_dma_quirks is completely gone, hooray!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220320123016.57991-7-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After Shimoda-san's much appreciated refactoring of the quirk handling,
we can convert now the 'fixed_addr_mode' from an ugly global flag to a
regular quirk. This makes quirk handling more consistent and easier to
maintain.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220320123016.57991-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The whitelist has been refactored away with a0fb3fc8af ("mmc:
renesas_sdhi: remove whitelist for internal DMAC") so the comment
doesn't make any sense anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220320123016.57991-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When I read 'no_fallback', I forgot what fallback even though I was the
author of this change. Name it better to make the code easier to
understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220320123016.57991-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not explicitly expressed in the docs, but the needed data strobe
pin is indeed missing for D3. The BSP disables HS400 as well. This means
a little refactoring to reuse an already existing setup.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220320123016.57991-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We moved quirk handling out of the SDHI core to the individual drivers.
So, no need to include headers needed for soc_device_match et al.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220320123016.57991-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Way back in commit 4f25580fb8 ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands
It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.
The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:
08573eaf1a ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")
53e60650f7 ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")
In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.
Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:
[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card
Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.
Fixes: 08573eaf1a ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f7 ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb8 ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The i.MX DMA drivers are device tree only, nothing in
include/linux/platform_data/dma-imx.h has platform_data in it, so move
the file to include/linux/dma/imx-dma.h.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220414162249.3934543-10-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Secure erase is a very different operation from discard in that it is
a data integrity operation vs hint. Fully split the limits and helper
infrastructure to make the separation more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> [drbd]
Acked-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> [nifs2]
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org> [f2fs]
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Chao Yu <chao@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220415045258.199825-27-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just use a non-zero max_discard_sectors as an indicator for discard
support, similar to what is done for write zeroes.
The only places where needs special attention is the RAID5 driver,
which must clear discard support for security reasons by default,
even if the default stacking rules would allow for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> [drbd]
Acked-by: Jan Höppner <hoeppner@linux.ibm.com> [s390]
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220415045258.199825-25-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To make it unambiguous that mmc_hw_reset() is for cards and not for
controllers, we make the function argument mmc_card instead of mmc_host.
Also, all users are converted.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408080045.6497-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When HS400 tuning is complete and HS400 is going to be activated, we
have to keep the current number of TAPs and should not overwrite them
with a hardcoded value. This was probably a copy&paste mistake when
upporting HS400 support from the BSP.
Fixes: 26eb2607fa ("mmc: renesas_sdhi: add eMMC HS400 mode support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220404114902.12175-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previous documentation was vague, so we included SDR104 for slow SDnH
clock settings. It turns out now, that it is only needed for HS400.
Fixes: bb6d3fa98a ("clk: renesas: rcar-gen3: Switch to new SD clock handling")
Cc: stable@vger.kernel.org
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220404100508.3209-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During the card initialization process, the mmc core checks whether the
eMMC/SD card supports an internal writeback-cache and then enables it
inside the card.
Unfortunately, this isn't according to what the mmc core reports to the
upper block layer. Instead, the writeback-cache support with REQ_FLUSH and
REQ_FUA, are being enabled depending on whether the host supports the CMD23
(MMC_CAP_CMD23) and whether an eMMC supports the reliable-write command.
This is wrong and it may also sound awkward. In fact, it's a remnant
from when both eMMC/SD cards didn't have dedicated commands/support to
control the internal writeback-cache. In other words, it was the best we
could do at that point in time.
To fix the problem, but also without breaking backwards compatibility,
let's align the REQ_FLUSH support with whether the writeback-cache became
successfully enabled - for both eMMC and SD cards.
Cc: stable@kernel.org
Fixes: 881d1c25f7 ("mmc: core: Add cache control for eMMC4.5 device")
Fixes: 130206a615 ("mmc: core: Add support for cache ctrl for SD cards")
Depends-on: 97fce126e2 ("mmc: block: Issue a cache flush only when it's enabled")
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Michael Wu <michael@allwinnertech.com>
Link: https://lore.kernel.org/r/20220331073223.106415-1-michael@allwinnertech.com
[Ulf: Re-wrote the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce a SEND_STATUS check for writes through SPI to not mark
an unsuccessful write as successful.
Since SPI SD/MMC does not have states, after a write, the card will
just hold the line LOW until it is ready again. The driver marks the
write therefore as completed as soon as it reads something other than
all zeroes.
The driver does not distinguish from a card no longer signalling busy
and it being disconnected (and the line being pulled-up by the host).
This lead to writes being marked as successful when disconnecting
a busy card.
Now the card is ensured to be still connected by an additional CMD13,
just like non-SPI is ensured to go back to TRAN state.
While at it and since we already poll for the post-write status anyway,
we might as well check for SPIs error bits (any of them).
The disconnecting card problem is reproducable for me after continuous
write activity and randomly disconnecting, around every 20-50 tries
on SPI DS for some card.
Fixes: 7213d175e3 ("MMC/SD card driver learns SPI")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/76f6f5d2b35543bab3dfe438f268609c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sg and not data->sg when checking sg list elements. Else only the
first element alignment is checked.
The last element should be checked the same way, for_each_sg already set
sg to sg_next(sg).
Fixes: 46b723dd86 ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20220317111944.116148-2-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are
still creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkGznQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnFwCgwGD/syV+BH2krgY6cRixZz72vPsAn2RSnicd
2YUwSNCHoL+B7hvQMtDG
=A3X9
-----END PGP SIGNATURE-----
Merge tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are still
creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (104 commits)
vt_ioctl: fix potential spectre v1 in VT_DISALLOCATE
serial: 8250: fix XOFF/XON sending when DMA is used
tty: serial: samsung: Add ARTPEC-8 support
dt-bindings: serial: samsung: Add ARTPEC-8 UART
serial: sc16is7xx: Clear RS485 bits in the shutdown
tty: serial: samsung: simplify getting OF match data
tty: serial: samsung: constify variables and pointers
tty: serial: samsung: constify s3c24xx_serial_drv_data members
tty: serial: samsung: constify UART name
tty: serial: samsung: constify s3c24xx_serial_drv_data
tty: serial: samsung: reduce number of casts
tty: serial: samsung: embed s3c2410_uartcfg in parent structure
tty: serial: samsung: embed s3c24xx_uart_info in parent structure
serial: 8250_tegra: mark acpi_device_id as unused with !ACPI
tty: serial: bcm63xx: use more precise Kconfig symbol
serial: SERIAL_SUNPLUS should depend on ARCH_SUNPLUS
tty: serial: jsm: fix two assignments in if conditions
tty: serial: jsm: remove redundant assignments to variable linestatus
serial: 8250_mtk: make two read-only arrays static const
serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
...
Here is the big set of staging driver updates for 5.18-rc1.
Loads of tiny cleanups for almost all staging drivers in here, nothing
major at all. Highlights include:
- remove the ashmem Android driver. It is long-dead and if
there are any legacy userspace applications still using it,
the Android kernel images will maintain it, the community
shouldn't care about it anymore
- wfx wifi driver major cleanups. Should be ready to merge out
of staging soon, and will coordinate with the wifi maintainers
after -rc1 is out
- major cleanups and unwinding of the layers of the r8188eu
driver. It's amazing just how many unneeded layers of
abstraction is in there, just when we think it's done, another
is found...
- lots of tiny coding style cleanups in many other staging
drivers.
There will be merge conflict with a fbtft change and the spi driver
changes in your tree, but it's pretty obvious what to do (the function
shouldn't return anything.)
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG1cA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylndwCfVhxKnbTYKtOs6UEr5pgPCoQCioUAn0Y2i0TG
4aFeeKUyL8VGdAitL+tp
=E6v7
-----END PGP SIGNATURE-----
Merge tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates for 5.18-rc1.
Loads of tiny cleanups for almost all staging drivers in here, nothing
major at all. Highlights include:
- remove the ashmem Android driver. It is long-dead and if there are
any legacy userspace applications still using it, the Android
kernel images will maintain it, the community shouldn't care about
it anymore
- wfx wifi driver major cleanups. Should be ready to merge out of
staging soon, and will coordinate with the wifi maintainers after
-rc1 is out
- major cleanups and unwinding of the layers of the r8188eu driver.
It's amazing just how many unneeded layers of abstraction is in
there, just when we think it's done, another is found...
- lots of tiny coding style cleanups in many other staging drivers.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (455 commits)
staging: r8188eu: remove unnecessary memset in r8188eu
staging: greybus: introduce pwm_ops::apply
staging: rts5208: Resolve checkpatch.pl issues.
staging: sm750fb: fix naming style
staging: fbtft: Consider type of init sequence values in fbtft_init_display()
staging: fbtft: Constify buf parameter in fbtft_dbg_hex()
staging: mmal-vchiq: clear redundant item named bulk_scratch
mips: dts: ralink: add MT7621 SoC
staging: r8188eu: remove some unused local ieee80211 macros
staging: r8188eu: make rtl8188e_process_phy_info static
staging: r8188eu: remove unused function prototype
staging: r8188eu: remove three unused receive defines
staging: r8188eu: remove unnecessary initializations
staging: rtl8192e: Fix spelling mistake "RESQUEST" -> "REQUEST"
MAINTAINERS: remove the obsolete file entry for staging in ANDROID DRIVERS
staging: r8188eu: proper error handling in rtw_init_drv_sw
staging: r8188eu: call _cancel_timer_ex from _rtw_free_recv_priv
staging: vt6656: Removed unused variable vt3342_vnt_threshold
staging: vt6656: Removed unused variable bb_vga_0
staging: remove ashmem
...
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
- Convert to sysfs_emit() in favor of sprintf()
- Improve fallback to speed modes if eMMC HS200 fails
MMC host:
- dw_mmc: Allow variants to set minimal supported clock rate
- dw-mmc-rockchip: Fix problems with invalid clock rates
- litex_mmc: Add new DT based driver for the LiteX's LiteSDCard interface
- litex_mmc: Add Gabriel Somlo and Joel Stanley as co-maintainers for LiteX
- mtk-sd: Add support for the Mediatek MT8186 variant
- renesas_sdhi: Add support for RZ/G2UL variant
- renesas_sdhi: Add support for RZ/V2L variant
- rtsx_pci: Adjust power-on sequence to conform to the SD spec
- sdhci-am654: Add support for TI's AM62 variant
- sdhci_am654: Fixup support for TI's AM64 variant
- sdhci-esdhc-imx: Add support for the imx93 variant
- sdhci-msm: Add support for the msm8953 variant
- sdhci-pci-gli: Add support for runtime PM for the GL9763E variant
- sdhci-pci-gli: Adjustments of the SSC function for the GL975x variants
- sdhci-tegra: Add support for wake on SD card event
- sunxi-mmc: Add support for Allwinner's F1c100s variant
- sunxi-mmc: Add support for D1 MMC variant
-----BEGIN PGP SIGNATURE-----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=1Iot
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Convert to sysfs_emit() in favor of sprintf()
- Improve fallback to speed modes if eMMC HS200 fails
MMC host:
- dw_mmc: Allow variants to set minimal supported clock rate
- dw-mmc-rockchip: Fix problems with invalid clock rates
- litex_mmc: Add new DT based driver for the LiteX's LiteSDCard
interface
- litex_mmc: Add Gabriel Somlo and Joel Stanley as co-maintainers for
LiteX
- mtk-sd: Add support for the Mediatek MT8186 variant
- renesas_sdhi: Add support for RZ/G2UL variant
- renesas_sdhi: Add support for RZ/V2L variant
- rtsx_pci: Adjust power-on sequence to conform to the SD spec
- sdhci-am654: Add support for TI's AM62 variant
- sdhci_am654: Fixup support for TI's AM64 variant
- sdhci-esdhc-imx: Add support for the imx93 variant
- sdhci-msm: Add support for the msm8953 variant
- sdhci-pci-gli: Add support for runtime PM for the GL9763E variant
- sdhci-pci-gli: Adjustments of the SSC function for the GL975x
variants
- sdhci-tegra: Add support for wake on SD card event
- sunxi-mmc: Add support for Allwinner's F1c100s variant
- sunxi-mmc: Add support for D1 MMC variant"
* tag 'mmc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (37 commits)
dt-bindings: mmc: renesas,sdhi: Document RZ/G2UL SoC
mmc: tmio: remove outdated members from host struct
mmc: mtk-sd: Silence delay phase calculation debug log
mmc: davinci_mmc: Handle error for clk_enable
mmc: sdhci-pci-gli: Add runtime PM for GL9763E
mmc: core: Drop HS400 caps unless 8-bit bus is supported too
mmc: host: Return an error when ->enable_sdio_irq() ops is missing
mmc: core: Improve fallback to speed modes if eMMC HS200 fails
dt-bindings: mmc: sunxi: add Allwinner F1c100s compatible
mmc: dw-mmc-rockchip: Fix handling invalid clock rates
mmc: dw_mmc: Support setting f_min from host drivers
mmc: host: Drop commas after SoC match table sentinels
mmc: rtsx: add 74 Clocks in power on flow
dt-bindings: mmc: renesas,sdhi: Document RZ/V2L SoC
mmc: sh_mmcif: Simplify division/shift logic
mmc: sdhci_am654: Add Support for TI's AM62 SoC
dt-bindings: mmc: imx-esdhc: Add imx93 compatible string
dt-bindings: mmc: sdhci-am654: Add compatible string for AM62 SoC
mmc: sdhci_am654: Fix the driver data of AM64 SoC
mmc: core: use sysfs_emit() instead of sprintf()
...
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
The wrappers are gone for two years now but they have still pointers
reserved in the tmio_mmc_host struct. Remove them.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: f22084b662 ("mmc: tmio: remove superfluous callback wrappers")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220311140542.5407-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver prints the following log everytime data is written to RPMB:
mtk-msdc 11230000.mmc: phase: [map:ffffffff] [maxlen:32] [final:10]
dev_info is used to print that log but it seems that log is only
useful for debbuging. Use dev_dbg instead of dev_info.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220311103320.3072171-1-abailon@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: bbce5802af ("davinci: mmc: updates to suspend/resume implementation")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220308071415.1093393-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add runtime PM for GL9763E and disable PLL in runtime suspend. So power
gated of upstream port can be enabled. GL9763E has an auxiliary power
so it keep states in runtime suspend. In runtime resume, PLL is enabled
and waits for it to stabilize.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Kevin Chang <kevin.chang@lcfuturecenter.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220307090009.1386876-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc_select_hs400es() tries to switch to the HS400 ES mode, it may bail
out early if the host doesn't support an 8-bit buswidth, as it's required
for the HS400 mode.
To improve the situation, let's instead drop the HS400 bits from the
capability field if the 8-bit bus isn't supported. In this way, we allow
the mmc initialization to continue by trying a lower speed mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220303165151.129806-1-ulf.hansson@linaro.org
Even if the current WARN() notifies the user that something is severely
wrong, we can still end up in a PANIC() when trying to invoke the missing
->enable_sdio_irq() ops. Therefore, let's also return an error code and
prevent the host from being added.
While at it, move the code into a separate function to prepare for
subsequent changes and for further host caps validations.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220303165142.129745-1-ulf.hansson@linaro.org
In the error path of mmc_select_hs200() we are trying our best to restore
the card/host into a valid state. This makes sense, especially if we
encounter a simple switch error (-EBADMSG). However, rather than then
continue with using the legacy speed mode, let's try the other better speed
modes first. Additionally, let's update the card->mmc_avail_type to avoid
us from trying a broken HS200 mode again.
In an Amlogic S905W based TV box where the switch to HS200 mode fails for
the eMMC, this allows us to use the eMMC in DDR mode in favor of the legacy
mode, which greatly improves the performance.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20220303164522.129583-1-ulf.hansson@linaro.org
The Rockchip rk356x ciu clock cannot be set as low as the dw-mmc
hardware supports. This leads to a situation during card initialization
where the clock is set lower than the clock driver can support. The
dw-mmc-rockchip driver spews errors when this happens.
For normal operation this only happens a few times during boot, but when
cd-broken is enabled (in cases such as the SoQuartz module) this fires
multiple times each poll cycle.
Fix this by testing the lowest possible frequency that the clock driver
can support which is within the mmc specification. Divide that rate by
the internal divider and set f_min to this.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220305215835.2210388-3-pgwipeout@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host drivers may not be able to support frequencies as low as dw-mmc
supports. Unfortunately f_min isn't available when the drv_data->init
function is called, as the mmc_host struct hasn't been set up yet.
Support the host drivers saving the requested minimum frequency, so we
can later set f_min when it is available.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220305215835.2210388-2-pgwipeout@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It does not make sense to have a comma after a sentinel, as any new
elements must be added before the sentinel.
Add comments to clarify the purpose of the empty elements.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/9050fa278eaaa9e6ec719a3b158a2fad285560d0.1646311673.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 76bfc7ccc2 ("mmc: core: adjust polling interval for CMD1"),
significantly decreased the polling period from ~10-12ms into just a couple
of us. The purpose was to decrease the total time spent in the busy polling
loop, but unfortunate it has lead to problems, that causes eMMC cards to
never gets out busy and thus fails to be initialized.
To fix the problem, but also to try to keep some of the new improved
behaviour, let's start by using a polling period of 1-2ms, which then
increases for each loop, according to common polling loop in
__mmc_poll_for_busy().
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Huijin Park <huijin.park@samsung.com>
Fixes: 76bfc7ccc2 ("mmc: core: adjust polling interval for CMD1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/20220304105656.149281-1-ulf.hansson@linaro.org
SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct device *dev, is no longer needed at various functions, let's
therefore drop it to fix the build errors/warnings.
Fixes: 7570fb41e4 ("mmc: rtsx: Let MMC core handle runtime PM")
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220301115300.64332-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the controller present on the AM62x SoC.
There are instances:
sdhci0: 8bit bus width, max 200 MBps
sdhci1: 4bit bus width, max 100 MBps
sdhci2: 4bit bus width, max 100 MBps
The PHY used for 8 bit instance is same as the PHY for the 4 bit instance.
Therefore, introduce a new bus width independent compatible for AM62 SoC
that uses the driver data required for 4 bit instance.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220218072840.5629-1-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently meson_mmc_post_req() is called in meson_mmc_request() right
after meson_mmc_start_cmd(). This could lead to DMA unmapping before the request
is actually finished.
To fix, don't call meson_mmc_post_req() until meson_mmc_request_done().
Signed-off-by: Rong Chen <rong.chen@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220216124239.4007667-1-rong.chen@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMCSD IPs used in AM64 are the same as the ones used in J721E.
Therefore, fix this by using the driver data from J721E for AM64 too, for
both 8 and 4 bit instances.
Fixes: 754b7f2f7d ("mmc: sdhci_am654: Add Support for TI's AM64 SoC")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220211075056.26179-1-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sprintf() (still used in the MMC core for the sysfs output) is vulnerable
to the buffer overflow. Use the new-fangled sysfs_emit() instead.
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/717729b2-d65b-c72e-9fac-471d28d00b5a@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
D1's MMC controllers are unique in that they have the DMA address shift
(like A100) with a 13-bit descriptor size field (like sun4i). Add the
compatible and parameters for this new variant.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220203015112.12008-2-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only the device data is needed, not the entire struct of_device_id.
Use of_device_get_match_data() instead of of_match_device().
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20220202180648.1252154-6-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only the device data is needed, not the entire struct of_device_id.
Use of_device_get_match_data() instead of open coding of_match_device().
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20220202180648.1252154-5-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only the device data is needed,not the whole struct of_device_id.
Use of_device_get_match_data() instead of open coding of of_match_device().
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20220202180648.1252154-3-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only the device data is needed, not the whole struct of_device_id.
Use of_device_get_match_data() instead of open coding of of_match_device().
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20220202180648.1252154-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a vendor-specific bit at the bit26 of GL9750's register 878h and
GL9755's register 78h to decide whether to disable SSC function. If
this bit is set, the SSC function will be disabled.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20220119075406.36321-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SSC value is 0xFFE7 at 205MHz and may be saturated. Reduce the SSC
value to 0x5A1D at 205MHz to reduce this situation for GL9750 and GL9755.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20220119075306.36262-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
LiteX (https://github.com/enjoy-digital/litex) is a SoC framework
that targets FPGAs. LiteSDCard is a small footprint, configurable
SDCard core commonly used in LiteX designs.
The driver was first written in May 2020 and has been maintained
cooperatively by the LiteX community. Thanks to all contributors!
Co-developed-by: Kamil Rakoczy <krakoczy@antmicro.com>
Signed-off-by: Kamil Rakoczy <krakoczy@antmicro.com>
Co-developed-by: Maciej Dudek <mdudek@internships.antmicro.com>
Signed-off-by: Maciej Dudek <mdudek@internships.antmicro.com>
Co-developed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220113170300.3555651-4-gsomlo@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable GPIO wake source on SD card detect line. Physical card
insertion/removal event should wake the system from suspend.
Signed-off-by: Aniruddha Rao <anrao@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1642050969-21152-1-git-send-email-anrao@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since MMC core handles runtime PM reference counting, we can avoid doing
redundant runtime PM work in the driver. That means the only thing
commit 5b4258f672 ("misc: rtsx: rts5249 support runtime PM") misses is
to always enable runtime PM, to let its parent driver enable ASPM in the
runtime idle routine.
Fixes: 7499b529d9 ("mmc: rtsx: Use pm_runtime_{get,put}() to handle runtime PM")
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220216055435.2335297-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, the SDIO quirks are applied directly from the driver.
However, it is better to apply the quirks before driver probing. So,
this patch relocate the quirks in the MMC framework.
Note that the WF200 has no valid SDIO VID/PID. Therefore, we match DT
rather than on the SDIO VID/PID.
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20220216093112.92469-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge 5.17-rc4 into char-misc-next
We need the char/misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was reported that the mmc host structure could be accessed after it
was freed in moxart_remove(), so fix this by saving the base register of
the device and using it instead of the pointer dereference.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: Xin Xiong <xiongx18@fudan.edu.cn>
Cc: Xin Tan <tanxin.ctf@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Cc: linux-mmc@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Reported-by: whitehat002 <hackyzh002@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 5b4258f672 ("misc: rtsx: rts5249 support runtime PM") doesn't
use pm_runtime_{get,put}() helpers when it should, so the RPM refcount
keeps at zero, hence its parent driver, rtsx_pci, has to do lots of
weird tricks to keep it from runtime suspending.
So use those helpers at right places to properly manage runtime PM.
Fixes: 5b4258f672 ("misc: rtsx: rts5249 support runtime PM")
Cc: Ricky WU <ricky_wu@realtek.com>
Tested-by: Ricky WU <ricky_wu@realtek.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220125055010.1866563-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SD card is allowed to signal busy on DAT0 up to 1s after the
CMD49. According to SD spec (version 6.0 section 5.8.1.3) first host
waits until busy of CMD49 is released and only then polls Power
Management Status register up to 1s until the card indicates ready to
power off.
Without waiting for busy before polling status register sometimes card
becomes unresponsive and system fails to suspend:
[ 205.907459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 206.421274] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[ 206.421321] sunxi-mmc 1c0f000.mmc: send stop command failed
[ 206.421347] mmc0: error -110 reading status reg of PM func
[ 206.421366] PM: dpm_run_callback(): mmc_bus_suspend+0x0/0x74 returns -110
[ 206.421402] mmcblk mmc0:aaaa: PM: failed to suspend async: error -110
[ 206.437064] PM: Some devices failed to suspend, or early wake event detected
Tested with Sandisk Extreme PRO A2 64GB on Allwinner A64 system.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Fixes: 2c5d427690 ("mmc: core: Add support for Power Off Notification for SD cards")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220115121447.641524-1-andrej.skvortzov@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is no suitable resource, platform_get_resource() will return
NULL.
Therefore in order to avoid the dereference of the NULL pointer, it
should be better to check the 'res'.
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: stable@vger.kernel.org # v5.16+
Link: https://lore.kernel.org/r/20220119120006.1426964-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
And since the sdhci_setup_host() has already checked the return value of
the enable_dma, we need not check it in sdhci_resume_host() again.
Fixes: 5552d7ad59 ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220112083156.1124782-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
This is a continuation of the rework of device power management
macros used for declaring device power management callbacks (Paul
Cercueil).
-----BEGIN PGP SIGNATURE-----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=psFp
-----END PGP SIGNATURE-----
Merge tag 'pm-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"This is a continuation of the rework of device power management macros
used for declaring device power management callbacks (Paul Cercueil)"
* tag 'pm-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
iio: pressure: bmp280: Use new PM macros
PM: runtime: Add EXPORT[_GPL]_RUNTIME_DEV_PM_OPS macros
PM: runtime: Add DEFINE_RUNTIME_DEV_PM_OPS() macro
PM: core: Add EXPORT[_GPL]_SIMPLE_DEV_PM_OPS macros
PM: core: Remove static qualifier in DEFINE_SIMPLE_DEV_PM_OPS macro
PM: core: Remove DEFINE_UNIVERSAL_DEV_PM_OPS() macro
bitmap_for_each_{set,clear}_region() are similar to for_each_bit()
macros in include/linux/find.h, but interface and implementation
of them are different.
This patch adds for_each_bitrange() macros and drops unused
bitmap_*_region() API in sake of unification.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmHgHvgOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9/JBAAk1qY+2GE7a2j/dRW31rv2JxS3iMnCIdnp/Hn
c0mArt8iEDPXbgmQ2b+tnuqh5GSz073UPCorxkEdAkYisbGSzk22VnfWsNwbSEgC
p8Tqt8ma1blQWUYGzszQEN9u9BCLaMr1cO/ORZmD/f7hSq5W42Q8IYLTb1/9gdax
+pJyBg8Y52PAKURnKWzmDoasJeDoQauxZ9R0g3BgQHj8Hb3QHQonyqKxJlyFac/e
RyV7YycM2ES3Dj4u7TReRd9hdKeuzc2Wg8qYVC3x/9dzhKpvDM3Tg5ONw/58jW4x
G6tuEj5SeEKH2LRQYTOLYScz9lVUalv97PCsq5LkQrDLqrO3hT+vxQpRdBZefRIQ
+cKBd9GReRlQW9XCDrUs9ZuWtl1cyta8T3mk3WhTvjUcTlr1vd+TcyRoQvNhFNVH
LaTjD1526Yra8BxyzSe7tyHhvOIvRWwjzSfwCyYV9097wV82+rOReqHyMDhN7Djc
NbBQvoIh7v1Yo+hOYE3RUUhS5h+CJH8l43J1pWNODjXVYivYTzCOizDdJ8ktRaHE
gpQ1vAM4pW1R5mQsyIwj6G9B1bclYboVBjlE9SXCpT3vmDneIWuLUmNV89gyNW+p
96B3dL4BoCTyBtGYBtow2Es+/rX2dEWtM6pvOSHhRDoWL586Snr2lXDEbAQ9uZF9
zpq1uqs=
=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support. Per usual (or maybe just recent trends), Qualcomm gains a
handful of SoC drivers additions and has the largest diffstat. After
that there are quite a few updates to the Allwinner (sunxi) drivers to
support modular drivers and Renesas is heavily updated to add more
support for various clks. Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2 clock
drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers
-----BEGIN PGP SIGNATURE-----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=jB+l
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a couple patches in the framework core this time around but
they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support.
Per usual (or maybe just recent trends), Qualcomm gains a handful of
SoC drivers additions and has the largest diffstat. After that there
are quite a few updates to the Allwinner (sunxi) drivers to support
modular drivers and Renesas is heavily updated to add more support for
various clks.
Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in
drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2
clock drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (131 commits)
clk: visconti: Remove pointless NULL check in visconti_pll_add_lookup()
clk: mediatek: add mt7986 clock support
clk: mediatek: add mt7986 clock IDs
dt-bindings: clock: mediatek: document clk bindings for mediatek mt7986 SoC
clk: mediatek: clk-gate: Use regmap_{set/clear}_bits helpers
clk: mediatek: clk-gate: Shrink by adding clockgating bit check helper
clk: x86: Fix clk_gate_flags for RV_CLK_GATE
clk: x86: Use dynamic con_id string during clk registration
ACPI: APD: Add a fmw property clk-name
drivers: acpi: acpi_apd: Remove unused device property "is-rv"
x86: clk: clk-fch: Add support for newer family of AMD's SOC
clk: ingenic: Add MDMA and BDMA clocks
dt-bindings: clk/ingenic: Add MDMA and BDMA clocks
clk: bm1880: remove kfrees on static allocations
clk: Drop unused COMMON_CLK_STM32MP157_SCMI config
clk: st: clkgen-mux: search reg within node or parent
clk: st: clkgen-fsyn: search reg within node or parent
clk: Enable/Disable runtime PM for clk_summary
MAINTAINERS: Add entries for Toshiba Visconti PLL and clock controller
clk: visconti: Add support common clock driver and reset driver
...
Keep this macro in line with the other ones. This makes it possible to
use them in the cases where the underlying dev_pm_ops structure is
exported.
Restore the "static" qualifier in the two drivers where the
DEFINE_SIMPLE_DEV_PM_OPS macro was used.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* clk-x86:
clk: x86: Fix clk_gate_flags for RV_CLK_GATE
clk: x86: Use dynamic con_id string during clk registration
ACPI: APD: Add a fmw property clk-name
drivers: acpi: acpi_apd: Remove unused device property "is-rv"
x86: clk: clk-fch: Add support for newer family of AMD's SOC
clk: Introduce clk-tps68470 driver
platform/x86: int3472: Deal with probe ordering issues
platform/x86: int3472: Pass tps68470_regulator_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Pass tps68470_clk_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Add get_sensor_adev_and_name() helper
platform/x86: int3472: Split into 2 drivers
platform_data: Add linux/platform_data/tps68470.h file
i2c: acpi: Add i2c_acpi_new_device_by_fwnode() function
i2c: acpi: Use acpi_dev_ready_for_enumeration() helper
ACPI: delay enumeration of devices with a _DEP pointing to an INT3472 device
* clk-stm:
clk: stm32: Fix ltdc's clock turn off by clk_disable_unused() after system enter shell
* clk-amlogic:
clk: meson: gxbb: Fix the SDM_EN bit for MPLL0 on GXBB
* clk-allwinner:
clk: sunxi-ng: Add support for the D1 SoC clocks
clk: sunxi-ng: gate: Add macros for gates with fixed dividers
clk: sunxi-ng: mux: Add macros using clk_parent_data and clk_hw
clk: sunxi-ng: mp: Add macros using clk_parent_data and clk_hw
clk: sunxi-ng: div: Add macros using clk_parent_data and clk_hw
dt-bindings: clk: Add compatibles for D1 CCUs
clk: sunxi-ng: Allow the CCU core to be built as a module
clk: sunxi-ng: Convert early providers to platform drivers
clk: sunxi-ng: Allow drivers to be built as modules
clk: sunxi-ng: Export symbols used by CCU drivers
- Use common polling loop for CMD1
- Add support for DT compatibles for card quirks and use it for ti,wl1251
- Fixup storing of the OCR mask for MMC_QUIRK_NONSTD_SDIO
MMC host:
- dw_mmc: Add support for MMC_GEN_CMDs
- dw_mmc: Fixup calculation of the data timeout
- dw_mmc-exynos: Add support for the ARTPEC-8 variant
- jz4740: Add support for bi-directional DMA channels
- mmci: Add support for eMMC HS200 mode for the stm32 sdmmc variant
- mmci: Add support for stm32 sdmmc variant revision v2.2
- mtk-sd: A couple of various minor improvements
- omap_hsmmc: Drop redundant initialization for the ti,wl1251 chip
- sdhci-esdhc-imx: Add support for the i.MXRT series variant
- sdhci-esdhc-imx: Add Haibo Chen as maintainer
- sdhci-pci: Add support for the Intel ADL variant
- sdhci-pci-gli: GL975[50]: Add support for the Apple ARM64 variant
- sdhci-pci-o2micro: Improve support for SDR104/HS200
-----BEGIN PGP SIGNATURE-----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=JDAt
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Use common polling loop for CMD1
- Add support for DT compatibles for card quirks and use it for ti,wl1251
- Fixup storing of the OCR mask for MMC_QUIRK_NONSTD_SDIO
MMC host:
- dw_mmc: Add support for MMC_GEN_CMDs
- dw_mmc: Fixup calculation of the data timeout
- dw_mmc-exynos: Add support for the ARTPEC-8 variant
- jz4740: Add support for bi-directional DMA channels
- mmci: Add support for eMMC HS200 mode for the stm32 sdmmc variant
- mmci: Add support for stm32 sdmmc variant revision v2.2
- mtk-sd: A couple of various minor improvements
- omap_hsmmc: Drop redundant initialization for the ti,wl1251 chip
- sdhci-esdhc-imx: Add support for the i.MXRT series variant
- sdhci-esdhc-imx: Add Haibo Chen as maintainer
- sdhci-pci: Add support for the Intel ADL variant
- sdhci-pci-gli: GL975[50]: Add support for the Apple ARM64 variant
- sdhci-pci-o2micro: Improve support for SDR104/HS200"
* tag 'mmc-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (54 commits)
dt-bindings: mmc: synopsys-dw-mshc: integrate Altera and Imagination
mmc: pwrseq: Use bitmap_free() to free bitmap
dt-bindings: mmc: PL18x stop relying on order of dma-names
dt-bindings: mmc: sdhci-msm: Add compatible string for msm8994
mmc: au1xmmc: propagate errors from platform_get_irq()
mmc: sdhci-pci-o2micro: Restore the SD clock's base clock frequency
mmc: sdhci-pci-o2micro: Improve card input timing at SDR104/HS200 mode
mmc: mtk-sd: Assign src_clk parent to src_clk_cg for legacy DTs
mmc: mtk-sd: Fix usage of devm_clk_get_optional()
mmc: mtk-sd: Take action for no-sdio device-tree parameter
mmc: mtk-sd: Use BIT() and GENMASK() macros to describe fields
mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling
MAINTAINERS: Add i.MX sdhci maintainer
mmc: jz4740: Support using a bi-directional DMA channel
dt-bindings: mmc: ingenic: Support using bi-directional DMA channel
mmc: dw_mmc: Do not wait for DTO in case of error
mmc: dw_mmc: Add driver callbacks for data read timeout
mmc: dw_mmc-exynos: Add support for ARTPEC-8
dt-bindings: mmc: exynos-dw-mshc: Add support for ARTPEC-8
mmc: meson-mx-sdio: add IRQ check
...
- Add new P-state driver for AMD processors (Huang Rui).
- Fix initialization of min and max frequency QoS requests in the
cpufreq core (Rafael Wysocki).
- Fix EPP handling on Alder Lake in intel_pstate (Srinivas Pandruvada).
- Make intel_pstate update cpuinfo.max_freq when notified of HWP
capabilities changes and drop a redundant function call from that
driver (Rafael Wysocki).
- Improve IRQ support in the Qcom cpufreq driver (Ard Biesheuvel,
Stephen Boyd, Vladimir Zapolskiy).
- Fix double devm_remap() in the Mediatek cpufreq driver (Hector Yuan).
- Introduce thermal pressure helpers for cpufreq CPU cooling (Lukasz
Luba).
- Make cpufreq use default_groups in kobj_type (Greg Kroah-Hartman).
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Allow model-specific normal EPB value to be used in the intel_epb
sysfs attribute handling code (Srinivas Pandruvada).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
- Update outdated operating performance points (OPP) documentation
(Tang Yizhou).
- Reduce log severity for informative message regarding frequency
transition failures in devfreq (Tzung-Bi Shih).
- Add DRAM frequency controller devfreq driver for Allwinner sunXi
SoCs (Samuel Holland).
- Add missing COMMON_CLK dependency to sun8i devfreq driver (Arnd
Bergmann).
- Add support for new layout of Psys PowerLimit Register on SPR to
the Intel RAPL power capping driver (Zhang Rui).
- Fix typo in a comment in idle_inject.c (Jason Wang).
- Remove unused function definition from the DTPM (Dynamit Thermal
Power Management) power capping framework (Daniel Lezcano).
- Reduce DTPM trace verbosity (Daniel Lezcano).
-----BEGIN PGP SIGNATURE-----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=1egI
-----END PGP SIGNATURE-----
Merge tag 'pm-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The most signigicant change here is the addition of a new cpufreq
'P-state' driver for AMD processors as a better replacement for the
venerable acpi-cpufreq driver.
There are also other cpufreq updates (in the core, intel_pstate, ARM
drivers), PM core updates (mostly related to adding new macros for
declaring PM operations which should make the lives of driver
developers somewhat easier), and a bunch of assorted fixes and
cleanups.
Summary:
- Add new P-state driver for AMD processors (Huang Rui).
- Fix initialization of min and max frequency QoS requests in the
cpufreq core (Rafael Wysocki).
- Fix EPP handling on Alder Lake in intel_pstate (Srinivas
Pandruvada).
- Make intel_pstate update cpuinfo.max_freq when notified of HWP
capabilities changes and drop a redundant function call from that
driver (Rafael Wysocki).
- Improve IRQ support in the Qcom cpufreq driver (Ard Biesheuvel,
Stephen Boyd, Vladimir Zapolskiy).
- Fix double devm_remap() in the Mediatek cpufreq driver (Hector
Yuan).
- Introduce thermal pressure helpers for cpufreq CPU cooling (Lukasz
Luba).
- Make cpufreq use default_groups in kobj_type (Greg Kroah-Hartman).
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Allow model-specific normal EPB value to be used in the intel_epb
sysfs attribute handling code (Srinivas Pandruvada).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
- Update outdated operating performance points (OPP) documentation
(Tang Yizhou).
- Reduce log severity for informative message regarding frequency
transition failures in devfreq (Tzung-Bi Shih).
- Add DRAM frequency controller devfreq driver for Allwinner sunXi
SoCs (Samuel Holland).
- Add missing COMMON_CLK dependency to sun8i devfreq driver (Arnd
Bergmann).
- Add support for new layout of Psys PowerLimit Register on SPR to
the Intel RAPL power capping driver (Zhang Rui).
- Fix typo in a comment in idle_inject.c (Jason Wang).
- Remove unused function definition from the DTPM (Dynamit Thermal
Power Management) power capping framework (Daniel Lezcano).
- Reduce DTPM trace verbosity (Daniel Lezcano)"
* tag 'pm-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (53 commits)
x86, sched: Fix undefined reference to init_freq_invariance_cppc() build error
cpufreq: amd-pstate: Fix Kconfig dependencies for AMD P-State
cpufreq: amd-pstate: Fix struct amd_cpudata kernel-doc comment
cpuidle: use default_groups in kobj_type
x86: intel_epb: Allow model specific normal EPB value
MAINTAINERS: Add AMD P-State driver maintainer entry
Documentation: amd-pstate: Add AMD P-State driver introduction
cpufreq: amd-pstate: Add AMD P-State performance attributes
cpufreq: amd-pstate: Add AMD P-State frequencies attributes
cpufreq: amd-pstate: Add boost mode support for AMD P-State
cpufreq: amd-pstate: Add trace for AMD P-State module
cpufreq: amd-pstate: Introduce the support for the processors with shared memory solution
cpufreq: amd-pstate: Add fast switch function for AMD P-State
cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future processors
ACPI: CPPC: Add CPPC enable register function
ACPI: CPPC: Check present CPUs for determining _CPC is valid
ACPI: CPPC: Implement support for SystemIO registers
x86/msr: Add AMD CPPC MSR definitions
x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature flag
cpufreq: use default_groups in kobj_type
...
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
* iASL/Disassembler: Additional support for NHLT table (Bob Moore).
* Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
* Fix a couple of warnings under MSVC (Bob Moore).
* iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
* iASL/NHLT table: "Specific Data" field support (Bob Moore).
* Use original data_table_region pointer for accesses (Jessica
Clarke).
* Use original pointer for virtual origin tables (Jessica Clarke).
* Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
* Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
* iASL: Add suppport for AGDI table (Ilkka Koskinen).
* Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
* Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
* Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
* Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
* Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
* Fix wrong interpretation of PCC address (Sudeep Holla).
* Add support for PCC Opregion special context data (Sudeep Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
- Rework flushing of EC work while suspended to idle and clean up
the handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used
when the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh).
-----BEGIN PGP SIGNATURE-----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=IGwJ
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are usual ACPICA code updates (although there are more of them
than in the last few releases), a noticeable EC driver update (which
mostly consists of cleanups, though), the device enumeration quirks
handling rework from Hans, some updates eliminating unnecessary CPU
cache flushing in some places (processor idle and system-wide PM code)
and a bunch of assorted cleanups and fixes.
Specifics:
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
- iASL/Disassembler: Additional support for NHLT table (Bob
Moore).
- Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
- Fix a couple of warnings under MSVC (Bob Moore).
- iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
- iASL/NHLT table: "Specific Data" field support (Bob Moore).
- Use original data_table_region pointer for accesses (Jessica
Clarke).
- Use original pointer for virtual origin tables (Jessica Clarke).
- Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
- Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
- iASL: Add suppport for AGDI table (Ilkka Koskinen).
- Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
- Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
- Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
- Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
- Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
- Fix wrong interpretation of PCC address (Sudeep Holla).
- Add support for PCC Opregion special context data (Sudeep
Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system PM
transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang
Li).
- Rework flushing of EC work while suspended to idle and clean up the
handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used when
the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh)"
* tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype
ACPI / x86: Skip AC and battery devices on x86 Android tablets with broken DSDTs
ACPI / x86: Introduce an acpi_quirk_skip_acpi_ac_and_battery() helper
ACPI: processor: thermal: avoid cpufreq_get_policy()
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
ACPI: battery: Add the ThinkPad "Not Charging" quirk
ACPI: sysfs: use default_groups in kobj_type
ACPICA: Update version to 20211217
ACPICA: iASL/NHLT table: "Specific Data" field support
ACPICA: iASL: Add suppport for AGDI table
ACPICA: iASL: Add TDEL table to both compiler/disassembler
ACPICA: Fixed a couple of warnings under MSVC
ACPICA: Change a return_ACPI_STATUS (AE_BAD_PARAMETER)
ACPICA: Hardware: Do not flush CPU cache when entering S4 and S5
ACPICA: Add support for PCC Opregion special context data
ACPICA: Fix wrong interpretation of PCC address
...
Merge cpuidle updates, PM core updates and one hiberation-related
update for 5.17-rc1:
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
* pm-cpuidle:
cpuidle: use default_groups in kobj_type
cpuidle: Fix cpuidle_remove_state_sysfs() kerneldoc comment
cpuidle: menu: Fix typo in a comment
* pm-core:
PM: runtime: Simplify locking in pm_runtime_put_suppliers()
mmc: mxc: Use the new PM macros
mmc: jz4740: Use the new PM macros
PM: runtime: Add safety net to supplier device release
PM: runtime: Capture device status before disabling runtime PM
PM: core: Add new *_PM_OPS macros, deprecate old ones
PM: core: Redefine pm_ptr() macro
r8169: Avoid misuse of pm_ptr() macro
* pm-sleep:
PM: hibernate: Allow ACPI hardware signature to be honoured
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
Merge x86-specific ACPI updates, PMIC driver ACPI updates and a DPTF
driver update for 5.17-rc1:
- Rework the handling of device enumeration quirks in the x86-specific
code and add new quirks for known-broken platforms (Hans de Goede).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
* acpi-x86:
ACPI / x86: Skip AC and battery devices on x86 Android tablets with broken DSDTs
ACPI / x86: Introduce an acpi_quirk_skip_acpi_ac_and_battery() helper
mmc: sdhci-acpi: Use the new soc_intel_is_byt() helper
mmc: sdhci-acpi: Remove special handling for GPD win/pocket devices
ACPI / x86: Add PWM2 on the Xiaomi Mi Pad 2 to the always_present list
ACPI / x86: Add not-present quirk for the PCI0.SDHB.BRC1 device on the GPD win
ACPI / x86: Allow specifying acpi_device_override_status() quirks by path
ACPI: Change acpi_device_always_present() into acpi_device_override_status()
ACPI / x86: Drop PWM2 device on Lenovo Yoga Book from always present table
* acpi-pmic:
ACPI: PMIC: xpower: Fix _TMP ACPI errors
ACPI: PMIC: allow drivers to provide a custom lpat_raw_to_temp() function
ACPI: PMIC: constify all struct intel_pmic_opregion_data declarations
* acpi-dptf:
ACPI: DPTF: Update device ID in a comment
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV. Switch to propagating the error codes upstream.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com
Link: https://lore.kernel.org/r/f642ef4d-6027-eb2e-0257-1c4f13911aed@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drop the SD clock's base clock for an SDR104 card, as frequency is wrong when
inserting and SD2.0/SDR50 card.
Signed-off-by: Fred Ai <fred.ai@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211216060824.357-2-fred.ai@bayhubtech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 3c1a884436 ("mmc: mediatek: add support of source_cg clock")
an independent cg was introduced to avoid a hardware hang issue during
clock mode switches (subsequent commits will set that clock as optional).
When this clock is not present in device-tree, any operation is being
done on src_clk's parent (calling clk_get_parent()): to simplify this
and avoid checking for src_clk_cg presence everytime, just assign the
parent clock to src_clk_cg and remove the now useless checks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we get an error during probe of an optional clock with function
devm_clk_get_optional(), this means that the clock was provided, but
an error occurred: this has to be escalated to the probe function
for the driver probe to fail accordingly, or unexpected hardware
behavior may happen.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver was unconditionally enabling support for SDIO mode,
but we do have a generic "no-sdio" DT parameter that sets caps2
MMC_CAP2_NO_SDIO.
Modify the HW initialization sequence to enable SDIO support only
if it hasn't been explicitly disabled in device-tree.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Register fields are currently represented with open-coded bit
shifting: replace all occurrences of that to make use of kernel
provided macros BIT and GENMASK to increase human readability.
This patch provides no functional change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace all instances of open-coded while loops for polling registers
with calls to readl_poll_timeout() and, while at it, also fix some
possible infinite loop instances.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the MMC/SD controller in Ingenic SoCs work in half-duplex, it is
possible to use one single DMA channel for both TX and RX operations,
instead of using separate channels.
As some older Ingenic SoCs offer only a handful of DMA channels,
supporting bi-directional channels allow more hardware to use the
channels that would otherwise be used for the MMC/SD operation.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211220190840.108061-3-paul@crapouillou.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running the ARTPEC-8 DWMMC IP version, and a data error interrupt
comes during a data read transfer, there is no guarantee for the data
transfer over interrupt (DTO) to come within the specified data timeout.
This case is handled by the dto_timer handler which will complete the
request with the comment:
/*
* If DTO interrupt does NOT come in sending data state,
* we should notify the driver to terminate current transfer
* and report a data timeout to the core.
*/
But since the ARTPEC-8 DWMMC IP version, supports an extended TMOUT
register which allows longer timeouts than the non ARTPEC-8 version
does, waiting for the dto_timer to complete the request in error cases
may cause the request to take significantly longer time than necessary.
This is specifically true for the failing steps during tuning of a
device.
Fix this by completing the request when the error interrupt comes. Since
this fix is specific for the ARTPEC-8, a quirk is added.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20211220113026.21129-5-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
