The discov_update work queue is no longer used as a result
of the hci_sync rework.
The __hci_req_hci_power_on() function is no longer referenced in the
code as a result of the hci_sync rework.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add a preliminary version which will be updated later
to loop over vif's and sta's active links.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers using software encryption for multicast TX, such
as mac80211_hwsim, mac80211 needs to duplicate the multicast
frames on each link, if MLO is enabled. Do this, but don't
just make it dependent on the key but provide a separate flag
for drivers to opt out of this.
This is not very efficient, I expect that drivers will do it
in firmware/hardware or at least with DMA engine assistence,
so this is mostly for hwsim.
To make this work, also implement the SNS11 sequence number
space that an AP MLD shall have, and modify the API to the
__ieee80211_subif_start_xmit() function to always require the
link ID bits to be set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a couple of new things that should be possible
with MLO:
* selecting the link to transmit to a station by link ID,
which a previous patch added to the nl80211 API
* selecting the link by frequency, similarly
* allowing transmittion to an MLD without specifying any
channel or link ID, with MLD addresses
Enable these use cases. Also fix the address comparison
in client mode to use the AP (MLD) address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow optionally specifying the link ID to transmit on,
which can be done instead of the link frequency, on an
MLD addressed frame. Both can also be omitted in which
case the frame must be MLD addressed and link selection
(and address translation) will be done on lower layers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the low level driver reports hardware timestamps for frame
TX status or frame RX, pass the timestamps to cfg80211.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add hardware timestamps to management frame RX info.
This shall be used by drivers that support hardware timestamping for
Timing measurement and Fine timing measurement action frames RX.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The functions for reporting rx management take many arguments.
Collect all the arguments into a struct, which also make it easier
to add more arguments if needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a function for reporting TX status with hardware timestamps. This
function shall be used for reporting the TX status of Timing
measurement and Fine timing measurement action frames by devices that
support reporting hardware timestamps.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds missing includes to headers under include/net.
All these problems are currently masked by the existing users
including the missing dependency before the broken header.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_adv_win_scale, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce bpf_ct_set_status and bpf_ct_change_status kfunc helpers in
order to set nf_conn field of allocated entry or update nf_conn status
field of existing inserted entry. Use nf_ct_change_status_common to
share the permitted status field changes between netlink and BPF side
by refactoring ctnetlink_change_status.
It is required to introduce two kfuncs taking nf_conn___init and nf_conn
instead of sharing one because KF_TRUSTED_ARGS flag causes strict type
checking. This would disallow passing nf_conn___init to kfunc taking
nf_conn, and vice versa. We cannot remove the KF_TRUSTED_ARGS flag as we
only want to accept refcounted pointers and not e.g. ct->master.
Hence, bpf_ct_set_* kfuncs are meant to be used on allocated CT, and
bpf_ct_change_* kfuncs are meant to be used on inserted or looked up
CT entry.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-10-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introduce bpf_ct_set_timeout and bpf_ct_change_timeout kfunc helpers in
order to change nf_conn timeout. This is same as ctnetlink_change_timeout,
hence code is shared between both by extracting it out to
__nf_ct_change_timeout. It is also updated to return an error when it
sees IPS_FIXED_TIMEOUT_BIT bit in ct->status, as that check was missing.
It is required to introduce two kfuncs taking nf_conn___init and nf_conn
instead of sharing one because KF_TRUSTED_ARGS flag causes strict type
checking. This would disallow passing nf_conn___init to kfunc taking
nf_conn, and vice versa. We cannot remove the KF_TRUSTED_ARGS flag as we
only want to accept refcounted pointers and not e.g. ct->master.
Apart from this, bpf_ct_set_timeout is only called for newly allocated
CT so it doesn't need to inspect the status field just yet. Sharing the
helpers even if it was possible would make timeout setting helper
sensitive to order of setting status and timeout after allocation.
Hence, bpf_ct_set_* kfuncs are meant to be used on allocated CT, and
bpf_ct_change_* kfuncs are meant to be used on inserted or looked up
CT entry.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-9-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introduce bpf_xdp_ct_alloc, bpf_skb_ct_alloc and bpf_ct_insert_entry
kfuncs in order to insert a new entry from XDP and TC programs.
Introduce bpf_nf_ct_tuple_parse utility routine to consolidate common
code.
We extract out a helper __nf_ct_set_timeout, used by the ctnetlink and
nf_conntrack_bpf code, extract it out to nf_conntrack_core, so that
nf_conntrack_bpf doesn't need a dependency on CONFIG_NF_CT_NETLINK.
Later this helper will be reused as a helper to set timeout of allocated
but not yet inserted CT entry.
The allocation functions return struct nf_conn___init instead of
nf_conn, to distinguish allocated CT from an already inserted or looked
up CT. This is later used to enforce restrictions on what kfuncs
allocated CT can be used with.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220721134245.2450-8-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make use of hci_cmd_sync_queue for removing an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of hci_cmd_sync_queue for adding an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT core driver should addtionally check LMP feature bit
"Erroneous Data Reporting" instead of quirk
HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if
HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken.
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587
This feature indicates whether the device is able to support the
Packet_Status_Flag and the HCI commands HCI_Write_Default_-
Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_-
Data_Reporting.
the quirk was introduced by 'commit cde1a8a992 ("Bluetooth: btusb: Fix
and detect most of the Chinese Bluetooth controllers")' to mark HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT
device driver, but the reason why these two HCI commands are broken is
that feature "Erroneous Data Reporting" is not enabled by firmware, this
scenario is illustrated by below log of QCA controllers with USB I/F:
@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 288 entries
......
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
Status: Success (0x00)
Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The bt_skb_sendmsg() function can't return NULL so there is no need to
check for that. Several of these checks were removed previously but
this one was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The scan response and advertising data needs to be tracked on a per
instance (adv_info) since when these instaces are removed so are their
data, to fix that new flags are introduced which is used to mark when
the data changes and then checked to confirm when the data needs to be
synced with the controller.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When HCI_USERCHANNEL is used, unregister the suspend notifier when
binding and register when releasing. The userchannel socket should be
left alone after open is completed.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Simplify nf_ct_get_tuple(), from Jackie Liu.
2) Add format to request_module() call, from Bill Wendling.
3) Add /proc/net/stats/nf_flowtable to monitor in-flight pending
hardware offload objects to be processed, from Vlad Buslov.
4) Missing rcu annotation and accessors in the netfilter tree,
from Florian Westphal.
5) Merge h323 conntrack helper nat hooks into single object,
also from Florian.
6) A batch of update to fix sparse warnings treewide,
from Florian Westphal.
7) Move nft_cmp_fast_mask() where it used, from Florian.
8) Missing const in nf_nat_initialized(), from James Yonan.
9) Use bitmap API for Maglev IPVS scheduler, from Christophe Jaillet.
10) Use refcount_inc instead of _inc_not_zero in flowtable,
from Florian Westphal.
11) Remove pr_debug in xt_TPROXY, from Nathan Cancellor.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: xt_TPROXY: remove pr_debug invocations
netfilter: flowtable: prefer refcount_inc
netfilter: ipvs: Use the bitmap API to allocate bitmaps
netfilter: nf_nat: in nf_nat_initialized(), use const struct nf_conn *
netfilter: nf_tables: move nft_cmp_fast_mask to where its used
netfilter: nf_tables: use correct integer types
netfilter: nf_tables: add and use BE register load-store helpers
netfilter: nf_tables: use the correct get/put helpers
netfilter: x_tables: use correct integer types
netfilter: nfnetlink: add missing __be16 cast
netfilter: nft_set_bitmap: Fix spelling mistake
netfilter: h323: merge nat hook pointers into one
netfilter: nf_conntrack: use rcu accessors where needed
netfilter: nf_conntrack: add missing __rcu annotations
netfilter: nf_flow_table: count pending offload workqueue tasks
net/sched: act_ct: set 'net' pointer when creating new nf_flow_table
netfilter: conntrack: use correct format characters
netfilter: conntrack: use fallthrough to cleanup
====================
Link: https://lore.kernel.org/r/20220720230754.209053-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reading sysctl_tcp_slow_start_after_idle, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 35089bb203 ("[TCP]: Add tcp_slow_start_after_idle sysctl.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_udp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 63a6fff353 ("net: Avoid receiving packets with an l3mdev on unbound UDP sockets")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_ip_prot_sock is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
Fixes: 4548b683b7 ("Introduce a sysctl that modifies the value of PROT_SOCK.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some synchronization issues(amt->status, amt->req_cnt, etc)
if the interface is in gateway mode because gateway message handlers
are processed concurrently.
This applies a work queue for processing these messages instead of
expanding the locking context.
So, the purposes of this patch are to fix exist race conditions and to make
gateway to be able to validate a gateway status more correctly.
When the AMT gateway interface is created, it tries to establish to relay.
The establishment step looks stateless, but it should be managed well.
In order to handle messages in the gateway, it saves the current
status(i.e. AMT_STATUS_XXX).
This patch makes gateway code to be worked with a single thread.
Now, all messages except the multicast are triggered(received or
delay expired), and these messages will be stored in the event
queue(amt->events).
Then, the single worker processes stored messages asynchronously one
by one.
The multicast data message type will be still processed immediately.
Now, amt->lock is only needed to access the event queue(amt->events)
if an interface is the gateway mode.
Fixes: cbc21dc1cf ("amt: add data plane of amt interface")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove locked versions of functions that are no longer used by anyone.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prepare for devlink reload being called with devlink->lock held and
convert the netdevsim driver to use unlocked devlink API during init and
fini flows. Take devl_lock() in reload_down() and reload_up() ops in the
meantime before reload cmd is converted to take the lock itself.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_region_create/destroy() functions
to be used in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_dpipe*() functions to be used
in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_sb*() functions to be used
in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devlink_resource*() functions to be used
in drivers called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add unlocked variants of devl_trap*() functions to be used in drivers
called-in with devlink->lock held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reading sysctl_tcp_notsent_lowat, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: c9bee3b7fd ("tcp: TCP_NOTSENT_LOWAT socket option")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading these sysctl knobs, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- tcp_retries1
- tcp_retries2
- tcp_orphan_retries
- tcp_fin_timeout
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_keepalive_(time|probes|intvl), they can be changed
concurrently. Thus, we need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Async crypto currently benefits from the fact that we decrypt
in place. When we allow input and output to be different skbs
we will have to hang onto the input while we move to the next
record. Clone the inputs and keep them on a list.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer allow a decrypted skb to remain linked to ctx->recv_pkt.
Anything on the list is decrypted, anything on ctx->recv_pkt needs
to be decrypted.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
recvmsg() in TLS gets data from the skb list (rx_list) or fresh
skbs we read from TCP via strparser. The former holds skbs which were
already decrypted for peek or decrypted and partially consumed.
tls_wait_data() only notices appearance of fresh skbs coming out
of TCP (or psock). It is possible, if there is a concurrent call
to peek() and recv() that the peek() will move the data from input
to rx_list without recv() noticing. recv() will then read data out
of order or never wake up.
This is not a practical use case/concern, but it makes the self
tests less reliable. This patch solves the problem by allowing
only one reader in.
Because having multiple processes calling read()/peek() is not
normal avoid adding a lock and try to fast-path the single reader
case.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the sysctl smcr_buf_type for setting
the type of SMC-R sndbufs and RMBs.
Valid values includes:
- SMCR_PHYS_CONT_BUFS, which means use physically contiguous
buffers for better performance and is the default value.
- SMCR_VIRT_CONT_BUFS, which means use virtually contiguous
buffers in case of physically contiguous memory is scarce.
- SMCR_MIXED_BUFS, which means first try to use physically
contiguous buffers. If not available, then use virtually
contiguous buffers.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e21145a987 ("ipv4: namespacify ip_early_demux sysctl knob") made
it possible to enable/disable early_demux on a per-netns basis. Then, we
introduced two knobs, tcp_early_demux and udp_early_demux, to switch it for
TCP/UDP in commit dddb64bcb3 ("net: Add sysctl to toggle early demux for
tcp and udp"). However, the .proc_handler() was wrong and actually
disabled us from changing the behaviour in each netns.
We can execute early_demux if net.ipv4.ip_early_demux is on and each proto
.early_demux() handler is not NULL. When we toggle (tcp|udp)_early_demux,
the change itself is saved in each netns variable, but the .early_demux()
handler is a global variable, so the handler is switched based on the
init_net's sysctl variable. Thus, netns (tcp|udp)_early_demux knobs have
nothing to do with the logic. Whether we CAN execute proto .early_demux()
is always decided by init_net's sysctl knob, and whether we DO it or not is
by each netns ip_early_demux knob.
This patch namespacifies (tcp|udp)_early_demux again. For now, the users
of the .early_demux() handler are TCP and UDP only, and they are called
directly to avoid retpoline. So, we can remove the .early_demux() handler
from inet6?_protos and need not dereference them in ip6?_rcv_finish_core().
If another proto needs .early_demux(), we can restore it at that time.
Fixes: dddb64bcb3 ("net: Add sysctl to toggle early demux for tcp and udp")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20220713175207.7727-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reading sysctl_tcp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 6dd9a14e92 ("net: Allow accepted sockets to be bound to l3mdev domain")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_fwmark_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 84f39b08d7 ("net: support marking accepting TCP sockets")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fwmark_reflect, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: e110861f86 ("net: add a sysctl to reflect the fwmark on replies")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_nonlocal_bind, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_fwd_use_pmtu, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: f87c10a8aa ("ipv4: introduce ip_dst_mtu_maybe_forward and protect forwarding path against pmtu spoofing")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_default_ttl, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MLO AP is transmitting to a non-MLO station, addr2 should be set
to a link address. This should be done before the frame is encrypted as
otherwise aad verification would fail. In case of software encryption
this can't be left for the device to handle, and should be done by
mac80211 when building the frame hdr.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a helper function cfg80211_get_iftype_ext_capa() to
look up interface type-specific (extended) capabilities.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since struct ieee80211_bss_conf already contains link_id,
passing link_id is not necessary.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of authentication with a legacy station, link addressed EAPOL
frames should be sent. Support it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have the per-interface type capabilities, currently for
extended capabilities, add the EML/MLD capabilities there
to have this advertised by the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the cfg80211_rx_assoc_resp() to cover multiple
BSSes, the AP MLD address and local link addresses
for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO we'll need a lot more arguments, including all the
BSS pointers and link addresses, so move the data to a struct
to be able to extend it more easily later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We only report the BSSID to userspace, so change the
argument from BSS struct pointer to AP address, which
we'll use to carry either the BSSID or AP MLD address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO, we need the ability to report back multiple BSS
structures to release, as well as the AP MLD address (if
attempting to make an MLO connection).
Unify cfg80211_assoc_timeout() and cfg80211_abandon_assoc()
into a new cfg80211_assoc_failure() that gets a structure
parameter with the necessary data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The race described by the comment in mac80211 hasn't existed
since the locking rework to use the same lock and for MLO we
need to pass the AP MLD address, so just pass the BSSID or
AP MLD address instead of the BSS struct pointer, and adjust
all the code accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To prepare a bit more for MLO in the client code,
track the AP's address (for now only the BSSID, but
will track the AP MLD's address later) separately
from the per-link BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It might be useful to drivers to be able to pass only the
link_conf pointer, rather than both the pointer and the
link_id; add the link_id to the link_conf to facility that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We might assign -1 to it in some cases when key is NULL,
which means the key_idx isn't used but can lead to a
warning from static checkers such as smatch.
Make the struct member signed simply to avoid that, we
only need a range of -1..3 anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an API for adding/modifying/removing a link of a station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return value is not used, so change the return value type to void.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When application runs in busy poll mode and does not receive a single
packet but only sends them, it is currently impossible to get into
napi_busy_loop() as napi_id is only marked on Rx side in xsk_rcv_check().
In there, napi_id is being taken from xdp_rxq_info carried by xdp_buff.
From Tx perspective, we do not have access to it. What we have handy is
the xsk pool.
Xsk pool works on a pool of internal xdp_buff wrappers called xdp_buff_xsk.
AF_XDP ZC enabled drivers call xp_set_rxq_info() so each of xdp_buff_xsk
has a valid pointer to xdp_rxq_info of underlying queue. Therefore, on Tx
side, napi_id can be pulled from xs->pool->heads[0].xdp.rxq->napi_id. Hide
this pointer chase under helper function, xsk_pool_get_napi_id().
Do this only for sockets working in ZC mode as otherwise rxq pointers would
not be initialized.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20220707130842.49408-1-maciej.fijalkowski@intel.com
nf_nat_initialized() doesn't modify passed struct nf_conn,
so declare as const.
This is helpful for code readability and makes it possible
to call nf_nat_initialized() with a const struct nf_conn *.
Signed-off-by: James Yonan <james@openvpn.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Return value of unregister_tcf_proto_ops is unused, remove it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath10k
* ethernet frame format support
rtw89
* TDLS support
cfg80211/mac80211
* airtime fairness fixes
* EHT support continued, especially in AP mode
* initial (and still major) rework for multi-link
operation (MLO) from 802.11be/wifi 7
As usual, also many small updates/cleanups/fixes/etc.
-----BEGIN PGP SIGNATURE-----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=smwk
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
A fairly large set of updates for next, highlights:
ath10k
* ethernet frame format support
rtw89
* TDLS support
cfg80211/mac80211
* airtime fairness fixes
* EHT support continued, especially in AP mode
* initial (and still major) rework for multi-link
operation (MLO) from 802.11be/wifi 7
As usual, also many small updates/cleanups/fixes/etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* queue selection in mesh/ocb
* queue handling on interface stop
* hwsim virtio device vs. some other virtio changes
* dt-bindings email addresses
* color collision memory allocation
* a const variable in rtw88
* shared SKB transmit in the ethernet format path
* P2P client port authorization
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAmLOcFIACgkQB8qZga/f
l8TK6g//dM2kjGZhyDJUnUicUplN6m4sHLeVqqWCJiUaZepg0Zb3zwEhfEjXnYgn
nWfFCqyRYN2JgESKFG2LNliAUW954ccu5mAHNoR41SXjwPxPLZblYqdirdtMsbv3
VM6Ar7WKVWqIer103lUOmiH+tSMObuUhfESbFVByutJfRAcWOolEIJdoAQEmqoKt
BgU0frkZLGpX9PTzJaT5KmgOnXstrWqdTY1JzLPR93k+fN0kwsOcBtwipqYTombI
gcnIMb5eY16EHQES9Rf02PIGDe9Oka2+xr9gfOAwFE5JWgh6j6TwHnXBi6UM5mby
/i6owhSS9km1rwTzsqJnpC89zZ1E26e5W7i6tDdQ+70OorSgPjMOGiyPNP+1KX0x
P9CfFGV6c2CICCfylva7lQXoBkAUn9uQsimGBOzYY3eWt5gYZKrwNistLKlrZQca
qRMRCXApfPvcyPvkX4DEuiJDgi+74nUqm0okIHLVHN4QfAuoq22DzTlTlFiF6OCJ
Fj5URCCfwyuwNtaF0W6IH8PnhkD8VQjYHH0RqclQAUaS5yJxj4x///GTGPwYDCxe
JcbASQfDOK1QmN4C3vOweym9J5jUdJR4fbvuj2iJhL0qQLrQZrKHoPfu8J5G4EyC
rtHAVmz8eI+IQtYsppRpQbRpNtmcj773FXhQ2wNqkZ6Y7i/GtFE=
=GrDi
-----END PGP SIGNATURE-----
Merge tag 'wireless-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
A small set of fixes for
* queue selection in mesh/ocb
* queue handling on interface stop
* hwsim virtio device vs. some other virtio changes
* dt-bindings email addresses
* color collision memory allocation
* a const variable in rtw88
* shared SKB transmit in the ethernet format path
* P2P client port authorization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain the same order as it is in devlink.c for function prototypes.
The most of the locked variants would very likely soon be removed
and the unlocked version would be the only one.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_raw_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 6897445fb1 ("net: provide a sysctl raw_l3mdev_accept for raw socket lookup with VRFs")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it can be used for port range filter offloading.
Co-developed-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu>
Signed-off-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch removed the last usage of the functions
devlink_rate_leaf_create() and devlink_rate_nodes_destroy(). Thus,
remove these function from devlink API.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The previous patch removed the last usage of the function
devlink_rate_nodes_destroy(). Thus, remove this function from devlink
API.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
... and cast result to u32 so sparse won't complain anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Same as the existing ones, no conversions. This is just for sparse sake
only so that we no longer mix be16/u16 and be32/u32 types.
Alternative is to add __force __beX in various places, but this
seems nicer.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Access to the hook pointers use correct helpers but the pointers lack
the needed __rcu annotation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
To improve hardware offload debuggability count pending 'add', 'del' and
'stats' flow_table offload workqueue tasks. Counters are incremented before
scheduling new task and decremented when workqueue handler finishes
executing. These counters allow user to diagnose congestion on hardware
offload workqueues that can happen when either CPU is starved and workqueue
jobs are executed at lower rate than new ones are added or when
hardware/driver can't keep up with the rate.
Implement the described counters as percpu counters inside new struct
netns_ft which is stored inside struct net. Expose them via new procfs file
'/proc/net/stats/nf_flowtable' that is similar to existing 'nf_conntrack'
file.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If we set XFRM security policy by calling setsockopt with option
IPV6_XFRM_POLICY, the policy will be stored in 'sock_policy' in 'sock'
struct. However tcp_v6_send_response doesn't look up dst_entry with the
actual socket but looks up with tcp control socket. This may cause a
problem that a RST packet is sent without ESP encryption & peer's TCP
socket can't receive it.
This patch will make the function look up dest_entry with actual socket,
if the socket has XFRM policy(sock_policy), so that the TCP response
packet via this function can be encrypted, & aligned on the encrypted
TCP socket.
Tested: We encountered this problem when a TCP socket which is encrypted
in ESP transport mode encryption, receives challenge ACK at SYN_SENT
state. After receiving challenge ACK, TCP needs to send RST to
establish the socket at next SYN try. But the RST was not encrypted &
peer TCP socket still remains on ESTABLISHED state.
So we verified this with test step as below.
[Test step]
1. Making a TCP state mismatch between client(IDLE) & server(ESTABLISHED).
2. Client tries a new connection on the same TCP ports(src & dst).
3. Server will return challenge ACK instead of SYN,ACK.
4. Client will send RST to server to clear the SOCKET.
5. Client will retransmit SYN to server on the same TCP ports.
[Expected result]
The TCP connection should be established.
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Sehee Lee <seheele@google.com>
Signed-off-by: Sewook Seo <sewookseo@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) refcount_inc_not_zero() is not semantically equivalent to
atomic_int_not_zero(), from Florian Westphal. My understanding was
that refcount_*() API provides a wrapper to easier debugging of
reference count leaks, however, there are semantic differences
between these two APIs, where refcount_inc_not_zero() needs a barrier.
Reason for this subtle difference to me is unknown.
2) packet logging is not correct for ARP and IP packets, from the
ARP family and netdev/egress respectively. Use skb_network_offset()
to reach the headers accordingly.
3) set element extension length have been growing over time, replace
a BUG_ON by EINVAL which might be triggerable from userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-07-09
We've added 94 non-merge commits during the last 19 day(s) which contain
a total of 125 files changed, 5141 insertions(+), 6701 deletions(-).
The main changes are:
1) Add new way for performing BTF type queries to BPF, from Daniel Müller.
2) Add inlining of calls to bpf_loop() helper when its function callback is
statically known, from Eduard Zingerman.
3) Implement BPF TCP CC framework usability improvements, from Jörn-Thorben Hinz.
4) Add LSM flavor for attaching per-cgroup BPF programs to existing LSM
hooks, from Stanislav Fomichev.
5) Remove all deprecated libbpf APIs in prep for 1.0 release, from Andrii Nakryiko.
6) Add benchmarks around local_storage to BPF selftests, from Dave Marchevsky.
7) AF_XDP sample removal (given move to libxdp) and various improvements around AF_XDP
selftests, from Magnus Karlsson & Maciej Fijalkowski.
8) Add bpftool improvements for memcg probing and bash completion, from Quentin Monnet.
9) Add arm64 JIT support for BPF-2-BPF coupled with tail calls, from Jakub Sitnicki.
10) Sockmap optimizations around throughput of UDP transmissions which have been
improved by 61%, from Cong Wang.
11) Rework perf's BPF prologue code to remove deprecated functions, from Jiri Olsa.
12) Fix sockmap teardown path to avoid sleepable sk_psock_stop, from John Fastabend.
13) Fix libbpf's cleanup around legacy kprobe/uprobe on error case, from Chuang Wang.
14) Fix libbpf's bpf_helpers.h to work with gcc for the case of its sec/pragma
macro, from James Hilliard.
15) Fix libbpf's pt_regs macros for riscv to use a0 for RC register, from Yixun Lan.
16) Fix bpftool to show the name of type BPF_OBJ_LINK, from Yafang Shao.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (94 commits)
selftests/bpf: Fix xdp_synproxy build failure if CONFIG_NF_CONNTRACK=m/n
bpf: Correctly propagate errors up from bpf_core_composites_match
libbpf: Disable SEC pragma macro on GCC
bpf: Check attach_func_proto more carefully in check_return_code
selftests/bpf: Add test involving restrict type qualifier
bpftool: Add support for KIND_RESTRICT to gen min_core_btf command
MAINTAINERS: Add entry for AF_XDP selftests files
selftests, xsk: Rename AF_XDP testing app
bpf, docs: Remove deprecated xsk libbpf APIs description
selftests/bpf: Add benchmark for local_storage RCU Tasks Trace usage
libbpf, riscv: Use a0 for RC register
libbpf: Remove unnecessary usdt_rel_ip assignments
selftests/bpf: Fix few more compiler warnings
selftests/bpf: Fix bogus uninitialized variable warning
bpftool: Remove zlib feature test from Makefile
libbpf: Cleanup the legacy uprobe_event on failed add/attach_event()
libbpf: Fix wrong variable used in perf_event_uprobe_open_legacy()
libbpf: Cleanup the legacy kprobe_event on failed add/attach_event()
selftests/bpf: Add type match test against kernel's task_struct
selftests/bpf: Add nested type to type based tests
...
====================
Link: https://lore.kernel.org/r/20220708233145.32365-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BUG_ON can be triggered from userspace with an element with a large
userdata area. Replace it by length check and return EINVAL instead.
Over time extensions have been growing in size.
Pick a sufficiently old Fixes: tag to propagate this fix.
Fixes: 7d7402642e ("netfilter: nf_tables: variable sized set element keys / data")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move macro MPTCPOPT_HMAC_LEN definition from net/mptcp/protocol.h to
include/net/mptcp.h.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to aid in adding mempools, in the next patch.
Link: https://lkml.kernel.org/r/20220704014243.153050-2-kent.overstreet@gmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
An upcoming patch is going to require passing the client through
p9_req_put() -> p9_req_free(), but that's awkward with the kref
indirection - so this patch switches to using refcount_t directly.
Link: https://lkml.kernel.org/r/20220704014243.153050-1-kent.overstreet@gmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
