This increases the maxmium supported frequency on 32-bit systems from
2^31 (signed long as used by clk_ops.round_rate, maximum value:
approx. 2.14GHz) to 2^32 (unsigned long as used by
clk_ops.determine_rate, maximum value: approx. 4.29GHz).
On Meson8/8b/8m2 the HDMI PLL and it's OD (post-dividers) are
capable of running at up to 2.97GHz. So switch the divider
implementation in clk-regmap to clk_ops.determine_rate to support these
higher frequencies on 32-bit systems.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210627223959.188139-4-martin.blumenstingl@googlemail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds the Neural Network Accelerator source clocks for g12b.
Initial support for sm1 already exist in
commit 2f1efa5340
("clk: meson: g12a: Add support for NNA CLK source clocks")
The sm1 and g12b share the same NNA source clocks.
This patch add missing NNA clocks for A311D (g12b).
Signed-off-by: Nick Xie <nick@khadas.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210604032957.224496-1-xieqinick@gmail.com
Use dev_err_probe() for clock and reset resources to indicate the deferral
reason through sysfs when waiting for the resource to come up.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210520073136.272925-1-jbrunet@baylibre.com
While some SoC samples are able to lock with a PLL factor of 55, others
samples can't. ATM, a minimum of 60 appears to work on all the samples
I have tried.
Even with 60, it sometimes takes a long time for the PLL to eventually
lock. The documentation says that the minimum rate of these PLLs DCO
should be 3GHz, a factor of 125. Let's use that to be on the safe side.
With factor range changed, the PLL seems to lock quickly (enough) so far.
It is still unclear if the range was the only reason for the delay.
Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429090325.60970-1-jbrunet@baylibre.com
This increases the maxmium supported frequency on 32-bit systems from
2^31 (signed long as used by clk_ops.round_rate, maximum value:
approx. 2.14GHz) to 2^32 (unsigned long as used by
clk_ops.determine_rate, maximum value: approx. 4.29GHz).
On Meson8/8b/8m2 the HDMI PLL and it's OD (post-dividers) are
capable of running at up to 2.97GHz. So switch the divider
implementation in clk-regmap to clk_ops.determine_rate to support these
higher frequencies on 32-bit systems.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210517203724.1006254-4-martin.blumenstingl@googlemail.com
On AXG platforms HHI_MIPI_CNTL0 is part of the MIPI/PCIe analog PHY
region and is not related to clock one and can be removed from it.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The XTAL clock is provided via .dts since Linux 5.6. Remove
compatibility code for .dtbs which are older than that.
The switch to the HHI syscon has been done with Linux 5.1. Also remove
any code needed to support .dtbs that have not switched to the HHI
syscon yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201221183624.932649-2-martin.blumenstingl@googlemail.com
Popagate the error code from meson_clk_pll_set_rate() when the PLL does
not lock with the new settings.
Fixes: 722825dcd5 ("clk: meson: migrate plls clocks to clk_regmap")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201226121556.975418-4-martin.blumenstingl@googlemail.com
The error codes returned by meson_clk_get_pll_settings() are all
negative. Make "ret" a signed integer in meson_clk_pll_set_rate() to
make it match with the clk_ops.set_rate API as well as the data type
returned by meson_clk_get_pll_settings().
Fixes: 8eed1db1ad ("clk: meson: pll: update driver for the g12a")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201226121556.975418-3-martin.blumenstingl@googlemail.com
The "rate" parameter in meson_clk_pll_set_rate() contains the new rate.
Retrieve the old rate with clk_hw_get_rate() so we don't inifinitely try
to switch from the new rate to the same rate again.
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201226121556.975418-2-martin.blumenstingl@googlemail.com
ability to get struct clk pointers from a struct clk_hw so that clk providers
can consume the clks they provide, if they need to do something like that. This
has been a long missing part of the clk provider API that will help us move
away from exposing a struct clk pointer in the struct clk_hw. Tracepoints are
added for the clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to help
developers understand the hardware enable state of clks in case firmware or
bootloader state is different than what is expected. Overall the core changes
are mostly improving the clk driver writing experience.
At the driver level, we have the usual collection of driver updates and new
drivers for new SoCs. This time around the Qualcomm folks introduced a good
handful of clk drivers for various parts of three or four SoCs. The SiFive
folks added a new clk driver for their FU740 SoCs, coming in second on the
diffstat and then Atmel AT91 and Amlogic SoCs had lots of work done after that
for various new features. One last thing to note in the driver area is that the
i.MX driver has gained a new binding to support SCU clks after being on the
list for many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and tweaks that
come from more testing and finding out that some configuration was wrong or
that a driver could support being built as a module.
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl/f/ycRHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSXjxg/7BJMFphpZmQb3iy/lZMYfgPh2yxZvrrBj
zJ2i1mMru/C3BkXTx29HCJvj6/VC2HgGLL6fzfwe7oY3XVRT1Vxlsvka9vNZSNc2
UYNa8GUwR0mSXDzp5KnzoAQfLwvSqWUIeT8WB+Z+CJ7WIAGWnXgBlqsf/d/mr9hg
JoAh+ROpbksL6hs61WJSm+7/Yu6efS0Yj0zzLZOINFWvDIOJ+Rp4g1u+qGH9tZyO
I2Bik75Sc8hqvLUP5SVzI/1H4yLB0On+ADgVRwjvrKPVX56alYquOUMsU+sy4SeY
ONQBki3vV5gtJHG1qvkwTC5/Yw20eUsrmrc7PNECvb1zo5Tp4QuOAR5nHCb4fg8u
n7RRd1MktTAUAQxTzBaNYtix3Q19fjSR44C/1B6lKk6xkN+w4uYLi2GHrADy9rXa
SwQVTKTGc8LjGywDaAOXdAyx2FMAtt1OvkTxZ238+aoHw5nQDHWKxu5TwYK6b5jG
aEFzTCIEYlzRLqcZyGONSD0WXmQWyoNiPwJ3B7RDRfpg7dPESyKIB4MzGWiX9eDy
lri/SoVH08c1sRf8AzIoi+CUNi8geTNAHHlJfiGznrv81ttVf3FioWyWLjr+SmBV
rNxn35WxeDWoCZqtrLJlg5skVgmD8BRXLZTI9udPG8u6D7OdWdJBuMZ6EelO+OZg
/n4w8tdo3cE=
=Wt9O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
This adds the MIPI DSI Host Pixel Clock, unlike AXG, the pixel clock can be different
from the VPU ENCL output clock to feed the DSI Host controller with a different clock rate.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201126141600.2084586-3-narmstrong@baylibre.com
Make it possible to build all clk drivers as modules, but default
remains built-in.
No functional changes.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201118191405.36798-1-khilman@baylibre.com
This adds the MIPI DSI Host clock, used to measure the signal timings
(ENC VSYNC or DW-MIPI-DSI eDPI timings).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200915124553.8056-5-narmstrong@baylibre.com
Add the clocks entries used in the video clock path, the clock path is
doubled to permit having different synchronized clocks for different parts
of the video pipeline.
The AXG only has a single ENCL CTS clock and even if VCLK exist along
VCLK2, only VCLK2 is used since it clocks the MIPI DSI IP directly.
All dividers are flagged with CLK_GET_RATE_NOCACHE, and all gates are
flagged with CLK_IGNORE_UNUSED since they are currently directly handled by
the Meson DRM Driver. Once the DRM Driver is fully migrated to using the
Common Clock Framework to handle the video clock tree, the
CLK_GET_RATE_NOCACHE and CLK_IGNORE_UNUSED will be dropped.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200915124553.8056-4-narmstrong@baylibre.com
Until now, nothing was done to unregister the dvfs clock notifiers of the
Amlogic g12 SoC family. This is not great but this driver was not really
expected to be unloaded. With the ongoing effort to build everything as
module for this platform, this needs to be cleanly handled.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021163847.595189-3-jbrunet@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
g12 clock controller used __clk_lookup() to get struct clk from a
struct clk_hw. This type of hack is no longer required as CCF now provides
the necessary functions to get this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021162147.563655-4-jbrunet@baylibre.com
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Nesting container_of() causes warnings with W=2, which is
annoying if it happens in headers and fills the build log
like:
In file included from drivers/clk/qcom/clk-alpha-pll.c:6:
drivers/clk/qcom/clk-alpha-pll.c: In function 'clk_alpha_pll_hwfsm_enable':
include/linux/kernel.h:852:8: warning: declaration of '__mptr' shadows a previous local [-Wshadow]
852 | void *__mptr = (void *)(ptr); \
| ^~~~~~
drivers/clk/qcom/clk-alpha-pll.c:155:31: note: in expansion of macro 'container_of'
155 | #define to_clk_alpha_pll(_hw) container_of(to_clk_regmap(_hw), \
| ^~~~~~~~~~~~
drivers/clk/qcom/clk-regmap.h:27:28: note: in expansion of macro 'container_of'
27 | #define to_clk_regmap(_hw) container_of(_hw, struct clk_regmap, hw)
| ^~~~~~~~~~~~
drivers/clk/qcom/clk-alpha-pll.c:155:44: note: in expansion of macro 'to_clk_regmap'
155 | #define to_clk_alpha_pll(_hw) container_of(to_clk_regmap(_hw), \
| ^~~~~~~~~~~~~
drivers/clk/qcom/clk-alpha-pll.c:254:30: note: in expansion of macro 'to_clk_alpha_pll'
254 | struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
| ^~~~~~~~~~~~~~~~
include/linux/kernel.h:852:8: note: shadowed declaration is here
852 | void *__mptr = (void *)(ptr); \
| ^~~~~~
Redefine two copies of the to_clk_regmap() macro as inline functions
to avoid a lot of these.
Fixes: ea11dda9e0 ("clk: meson: add regmap clocks")
Fixes: 085d7a4554 ("clk: qcom: Add a regmap type clock struct")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161411.3708639-1-arnd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-semicolon:
clk: meson: use semicolons rather than commas to separate statements
clk: mvebu: ap80x-cpu: use semicolons rather than commas to separate statements
clk: uniphier: use semicolons rather than commas to separate statements
* clk-axi-clkgen:
clk: axi-clkgen: Set power bits for fractional mode
clk: axi-clkgen: Add support for fractional dividers
* clk-qoriq:
clk: qoriq: modify MAX_PLL_DIV to 32
* clk-baikal:
clk: baikal-t1: Mark Ethernet PLL as critical
* clk-const:
clk: pxa: Constify static struct clk_ops
* clk-mmp2:
clk: mmp2: Fix the display clock divider base
Add the necessary bits so unnecessary amlogic clock controllers can be
compiled out. This allows to save a few kB when necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200828154735.435374-1-jbrunet@baylibre.com
On Amlogic Meson G12b platform, similar to fclk_div3, the fclk_div2
seems to be necessary for the system to operate correctly as well.
Typically, the clock also gets chosen by the eMMC peripheral. This
probably masked the problem so far. However, when booting from a SD
card the clock seems to get disabled which leads to a system freeze.
Let's mark this clock as critical, fixing boot from SD card on G12b
platforms.
Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/577e0129e8ee93972d92f13187ff4e4286182f67.1598629915.git.stefan@agner.ch
Fix the tdmout inverter of the g12a and following SoC families.
This inverter is special and needs two bits to be the inverse of each other
for the inverter to operate properly.
Fixes: 075001385c ("clk: meson: axg-audio: add g12a support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200729154359.1983085-4-jbrunet@baylibre.com
There are more differences than what we initially thought.
Let's keeps things clear and separate the axg and g12a regmap tables of the
audio clock controller.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200729154359.1983085-3-jbrunet@baylibre.com
This is yet another simple but odd driver for the audio block of the g12a
and sm1 SoC families.
For TDMOUT's sclk to be properly inverted, bit 29 of
AUDIO_CLK_TDMOUT_x_CTRL should be the inverse of bit 28.
IOW bit28 == !bit29 at all times
This setting is automatically applied on axg and the manual setting was
added on g12a.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200729154359.1983085-2-jbrunet@baylibre.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200703175114.15027-1-grandmaster@al2klimov.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
HHI_VIID_CLK_CNTL[19] is not part of the public S805 datasheet. However,
the GXBB driver defines this bit as a gate called "vclk2" and in the
3.10 kernel GPL code dump the following line can found:
WRITE_LCD_CBUS_REG_BITS(HHI_VIID_CLK_CNTL, 0, 19, 1); //disable vclk2_en
Add this gate clock to the Meson8/Meson8b/Meson8m2 clock controller to
complete the VCLK2 clock tree.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200629203904.2989007-3-martin.blumenstingl@googlemail.com
HHI_VID_CLK_CNTL[19] is documented as CLK_EN0. This description is the
same in the public S912 datasheet and the GXBB driver calls this gate
"vclk". Add this gate clock to the Meson8/Meson8b/Meson8m2 clock
controller because it's needed to make the video output work.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200629203904.2989007-2-martin.blumenstingl@googlemail.com
Drop CLK_IS_CRITICAL from fclk_div2. This was added because we didn't
know the relation between this clock and RGMII Ethernet. It turns out
that fclk_div2 is used as "timing adjustment clock" to generate the RX
delay on the MAC side - which was enabled by u-boot on Odriod-C1. When
using the RX delay on the PHY side or not using a RX delay at all then
this clock can be disabled.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200620161422.24114-1-martin.blumenstingl@googlemail.com
This adds the Neural Network Accelerator source clocks hierarchy, it's
2 simple composite clocks to feed the AXI interface and the Core of
the Neural Network Accelerator IP.
This IP is only present on the Amlogic SM1 SoCs family.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200610083012.5024-3-narmstrong@baylibre.com
Not all u-boot versions initialize the HHI_GP_PLL_CNTL[2-5] registers.
In that case all HHI_GPLL_PLL_CNTL[1-5] registers are 0x0 and when
booting Linux the PLL fails to lock.
The initialization sequence from u-boot is:
- put the PLL into reset
- write 0x59C88000 to HHI_GP_PLL_CNTL2
- write 0xCA463823 to HHI_GP_PLL_CNTL3
- write 0x0286A027 to HHI_GP_PLL_CNTL4
- write 0x00003000 to HHI_GP_PLL_CNTL5
- set M, N, OD and the enable bit
- take the PLL out of reset
- check if it has locked
- disable the PLL
In Linux we already initialize M, N, OD, the enable and the reset bits.
Also the HHI_GP_PLL_CNTL[2-5] registers with these magic values (the
exact meaning is unknown) so the PLL can lock when the vendor u-boot did
not initialize these registers yet.
Fixes: b882964b37 ("clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200501215717.735393-1-martin.blumenstingl@googlemail.com
The "vpu_0" or "vpu_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"vpu_0" and "vpu_1" gates. This makes the CCF switch to the "vpu_1"
tree when "vpu_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the VPU
clock.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200417184127.1319871-5-martin.blumenstingl@googlemail.com
The DIV{1,2,4,6,12}_EN bits are actually located in HHI_VID_CLK_CNTL
register:
- HHI_VID_CLK_CNTL[0] = DIV1_EN
- HHI_VID_CLK_CNTL[1] = DIV2_EN
- HHI_VID_CLK_CNTL[2] = DIV4_EN
- HHI_VID_CLK_CNTL[3] = DIV6_EN
- HHI_VID_CLK_CNTL[4] = DIV12_EN
Update the bits accordingly so we will enable the bits in the correct
register once we switch these clocks to be mutable.
Fixes: 6cb57c678b ("clk: meson: meson8b: add the read-only video clock trees")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200417184127.1319871-4-martin.blumenstingl@googlemail.com
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_POST and
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_PRE are active low. This means:
- asserting them requires setting the register value to 0
- de-asserting them requires setting the register value to 1
Set the register value accordingly for these two reset lines by setting
the inverted the register value compared to all other reset lines.
Fixes: 189621726b ("clk: meson: meson8b: register the built-in reset controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200417184127.1319871-3-martin.blumenstingl@googlemail.com
Use hdmi_pll_lvds_out as parent of the vid_pll_in_sel clock. It's not
easy to see that the vendor kernel does the same, but it actually does.
meson_clk_pll_ops in mainline still cannot fully recalculate all rates
from the HDMI PLL registers because some register bits (at the time of
writing it's unknown which bits are used for this) double the HDMI PLL
output rate (compared to simply considering M, N and FRAC) for some (but
not all) PLL settings.
Update the vid_pll_in_sel parent so our clock calculation works for
simple clock settings like the CVBS output (where no rate doubling is
going on). The PLL ops need to be fixed later on for more complex clock
settings (all HDMI rates).
Fixes: 6cb57c678b ("clk: meson: meson8b: add the read-only video clock trees")
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200417184127.1319871-2-martin.blumenstingl@googlemail.com
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
Also propagate set_rate requests from the gate to the divider and from
the divider to the the mux so the GPU clock frequency can be updated at
runtime (which will be required for GPU DVFS). Don't propagate rate
changes to the mux parents because we don't want to change the MPLL
clocks (these are reserved for audio).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200414195031.224021-3-martin.blumenstingl@googlemail.com
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
Also propagate set_rate requests from the gate to the divider and from
the divider to the the mux so the GPU clock frequency can be updated at
runtime (which will be required for GPU DVFS). Don't propagate rate
changes to the mux parents because we don't want to change the MPLL
clocks (these are reserved for audio).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200414195031.224021-2-martin.blumenstingl@googlemail.com
The HDMI TX controller requires the hdmi_sys clock to be enabled. Allow
changing the whole clock tree now that we know that one of our drivers
requires this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200330234535.3327513-3-martin.blumenstingl@googlemail.com
Export the HDMI system clock (used by the HDMI transmitter) so it can be
used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200330234535.3327513-2-martin.blumenstingl@googlemail.com
The aiu devices peripheral clocks needs the aiu and aiu_glue clocks to
operate. Reflect this hierarchy in the clock tree.
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the clocks used for the Amlogic G12A and compatible SoCs SPICC
controller to provide a more complete range of frequencies instead of the
SPICC internal divider over Xtal.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The aiu devices peripheral clocks needs the aiu and aiu_glue clocks to
operate. Reflect this hierarchy in the gxbb clock tree.
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the ACODEC clock gate to the gxl clk controller driver
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
- Support dangerous debugfs actions on clks with dead code
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
* clk-debugfs-danger:
clk: Add support for setting clk_rate via debugfs
* clk-basic-hw:
clk: divider: Add support for specifying parents via DT/pointers
clk: gate: Add support for specifying parents via DT/pointers
clk: mux: Add support for specifying parents via DT/pointers
clk: asm9260: Use parent accuracy in fixed rate clk
clk: fixed-rate: Document that accuracy isn't a rate
clk: fixed-rate: Add clk flags for parent accuracy
clk: fixed-rate: Add support for specifying parents via DT/pointers
clk: fixed-rate: Document accuracy member
clk: fixed-rate: Move to_clk_fixed_rate() to C file
clk: fixed-rate: Remove clk_register_fixed_rate_with_accuracy()
clk: fixed-rate: Convert to clk_hw based APIs
clk: gpio: Use DT way of specifying parents
* clk-renesas:
clk: renesas: Prepare for split of R-Car H3 config symbol
dt-bindings: clock: renesas: cpg-mssr: Fix r8a774b1 typo
clk: renesas: r7s9210: Add SPIBSC clock
clk: renesas: rcar-gen3: Allow changing the RPC[D2] clocks
clk: renesas: Remove use of ARCH_R8A7796
clk: renesas: rcar-gen2: Change multipliers and dividers to u8
* clk-amlogic:
clk: clarify that clk_set_rate() does updates from top to bottom
clk: meson: meson8b: make the CCF use the glitch-free mali mux
clk: meson: pll: Fix by 0 division in __pll_params_to_rate()
clk: meson: g12a: fix missing uart2 in regmap table
clk: meson: meson8b: use of_clk_hw_register to register the clocks
clk: meson: meson8b: don't register the XTAL clock when provided via OF
clk: meson: meson8b: change references to the XTAL clock to use [fw_]name
clk: meson: meson8b: use clk_hw_set_parent in the CPU clock notifier
clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller
dt-bindings: clock: meson8b: add the clock inputs
dt-bindings: clock: add the Amlogic Meson8 DDR clock controller binding
* clk-allwinner:
clk: sunxi: a23/a33: Export the MIPI PLL
clk: sunxi: a31: Export the MIPI PLL
clk: sunxi-ng: a64: export CLK_CPUX clock for DVFS
clk: sunxi-ng: add mux and pll notifiers for A64 CPU clock
clk: sunxi-ng: r40: Export MBUS clock
clk: sunxi: use of_device_get_match_data
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
This fixes a potential hang when changing the GPU frequency at runtime.
Fixes: 74e1f2521f ("clk: meson: meson8b: add the GPU clock tree")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
If the init callback is allowed to request resources, it needs a return
value to report the outcome of such a request.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lkml.kernel.org/r/20190924123954.31561-3-jbrunet@baylibre.com
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some meson pll registers can be initialized with 0 as N value, introducing
the following division by 0 when computing rate :
UBSAN: Undefined behaviour in drivers/clk/meson/clk-pll.c:75:9
division by zero
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc3-608075-g86c9af8630e1-dirty #400
Call trace:
dump_backtrace+0x0/0x1c0
show_stack+0x14/0x20
dump_stack+0xc4/0x100
ubsan_epilogue+0x14/0x68
__ubsan_handle_divrem_overflow+0x98/0xb8
__pll_params_to_rate+0xdc/0x140
meson_clk_pll_recalc_rate+0x278/0x3a0
__clk_register+0x7c8/0xbb0
devm_clk_hw_register+0x54/0xc0
meson_eeclkc_probe+0xf4/0x1a0
platform_drv_probe+0x54/0xd8
really_probe+0x16c/0x438
driver_probe_device+0xb0/0xf0
device_driver_attach+0x94/0xa0
__driver_attach+0x70/0x108
bus_for_each_dev+0xd8/0x128
driver_attach+0x30/0x40
bus_add_driver+0x1b0/0x2d8
driver_register+0xbc/0x1d0
__platform_driver_register+0x78/0x88
axg_driver_init+0x18/0x20
do_one_initcall+0xc8/0x24c
kernel_init_freeable+0x2b0/0x344
kernel_init+0x10/0x128
ret_from_fork+0x10/0x18
This checks if N is null before doing the division.
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
[jbrunet@baylibre.com: update the comment in above the fix]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Martin Blumenstingl