There is no need to call platform_get_irq() when the driver's probe()
method calls usb_add_hcd() -- the platform_get_irq()'s result will have
been stored already in the 'irq' local variable...
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/3e4ad969-f2ae-32f7-53fd-ea369f140703@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mv_ehci_enable() did not disable and unprepare clocks in case of
failures of phy_init(). Besides, it did not take into account failures
of ehci_clock_enable() (in effect, failures of clk_prepare_enable()).
The patch fixes both issues and gets rid of redundant wrappers around
clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit.
Found by Linux Driver Verification project (linuxtesting.org).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20210708083056.21543-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-6-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since they're only used if there's an skb.
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-5-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the current logic is:
struct sk_buff *skb2 = NULL;
...
if (!skb && !ncm->skb_tx_data)
return NULL;
if (skb) {
...
} else if (ncm->skb_tx_data)
...
}
return skb2;
Which means that first if statement is simply not needed.
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-4-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This condition is already checked for in ncm_wrap_ntb(),
except that that check is done with eth_dev->lock held
(it is grabbed by eth_start_xmit).
It's best to not be reaching into ncm struct without locks held.
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-3-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is simply not needed. This field is equivalent to skb being NULL.
Currently with the boolean set to true we call:
ncm->netdev->netdev_ops->ndo_start_xmit(NULL, ncm->netdev);
which calls u_ether's:
eth_start_xmit(NULL, ...)
which then calls:
skb = dev->wrap(dev->port_usb, NULL);
which calls back into f_ncm's:
ncm_wrap_ntb(..., NULL)
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should acquire the actual_length of an iso packet
from the iTD directly using FOTG210_ITD_LENGTH() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-4-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we should make use of the
usb_endpoint_* helpers instead and remove the unnecessary
max_packet()/hb_mult() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-3-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cb6a0db8fd for the
same reason as commit 43b78f1155 in the
ehci-hcd driver.
Alan writes:
What you can't see just from reading the patch is that in both
cases (ehci->itd_pool and ehci->sitd_pool) there are two
allocation paths -- the two branches of an "if" statement -- and
only one of the paths calls dma_pool_[z]alloc. However, the
memset is needed for both paths, and so it can't be eliminated.
Given that it must be present, there's no advantage to calling
dma_pool_zalloc rather than dma_pool_alloc.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-2-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sending zero length packet in DDMA mode perform by DMA descriptor
by setting SP (short packet) flag.
For DDMA in function dwc2_hsotg_complete_in() does not need to send
zlp.
Tested by USBCV MSC tests.
Fixes: f71b5e2533 ("usb: dwc2: gadget: fix zero length packet transfers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/967bad78c55dd2db1c19714eee3d0a17cf99d74a.1626777738.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr
function.") changed the way the driver handles power down modes in a such
way that it uses clock gating when no other power down mode is available.
This however doesn't work well on the DWC2 implementation used on the
Samsung SoCs. When a clock gating is enabled, system hangs. It looks that
the proper clock gating requires some additional glue code in the shared
USB2 PHY and/or Samsung glue code for the DWC2. To restore driver
operation on the Samsung SoCs simply skip enabling clock gating mode
until one finds what is really needed to make it working reliably.
Fixes: 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Cc: stable <stable@vger.kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210716050127.4406-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af3260528 ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -22
To fix the issue, disable the tx or rx interrupt in usb_pkt_pop().
Fixes: 2743e7f90d ("usb: renesas_usbhs: fix the usb_pkt_pop()")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624122039.596528-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of dwc2_hsotg_ep_stop_xfr() function uses poll
mode, first need to mask GINTSTS_GOUTNAKEFF interrupt.
In Slave mode GINTSTS_GOUTNAKEFF interrupt will be
aserted only after pop OUT NAK status packet from RxFIFO.
In dwc2_hsotg_ep_sethalt() function before setting
DCTL_SGOUTNAK need to unmask GOUTNAKEFF interrupt.
Tested by USBCV CH9 and MSC tests set in Slave, BDMA and DDMA.
All tests are passed.
Fixes: a4f8277145 ("usb: dwc2: gadget: Disable enabled HW endpoint in dwc2_hsotg_ep_disable")
Fixes: 6070636c49 ("usb: dwc2: Fix Stalling a Non-Isochronous OUT EP")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e17fad802bbcaf879e1ed6745030993abb93baf8.1626152924.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a66d21d7db ("usb: xhci: Add support for Renesas controller with
memory") added renesas_usb_fw.mem firmware reference to xhci-pci. Thus
modinfo indicates xhci-pci.ko has "firmware: renesas_usb_fw.mem". But
the firmware is only actually used with CONFIG_USB_XHCI_PCI_RENESAS. An
unusable firmware reference can trigger safety checkers which look for
drivers with unmet firmware dependencies.
Avoid referring to renesas_usb_fw.mem in circumstances when it cannot be
loaded (when CONFIG_USB_XHCI_PCI_RENESAS isn't set).
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Thelen <gthelen@google.com>
Link: https://lore.kernel.org/r/20210702071224.3673568-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
we found crash in dwc3_disconnect_gadget(),
it is because dwc->gadget_driver become NULL before async access.
7dc0c55e9f ('USB: UDC core: Add udc_async_callbacks gadget op')
suggest a common way to avoid such kind of issue.
this change implment the callback in dwc3 and
change related functions which have callback to usb gadget driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org>
Link: https://lore.kernel.org/r/20210629015118.7944-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.
To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar as with tcpm this patch lets fw_devlink know not to wait on the
fwnode to be populated as a struct device.
Without this patch, USB functionality can be broken on some previously
supported boards.
Fixes: 28ec344bb8 ("usb: typec: tcpm: Don't block probing of consumers of "connector" nodes")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210716120718.20398-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During interrupt registration, attach state is checked. If attached,
then the Type-C state is updated with typec_set_xxx functions and role
switch is set with usb_role_switch_set_role().
If the usb_role_switch parameter is error or null, the function simply
returns 0.
So, to update usb_role_switch role if a device is attached before the
irq is registered, usb_role_switch must be registered before irq
registration.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210716120718.20398-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MSI is used by the ehci-hcd driver, it can cause lost interrupts which
results in EHCI only continuing to work due to a polling fallback. But the
reliance of polling drastically reduces performance of any I/O through EHCI.
Interrupts are lost as the EHCI interrupt handler does not safely handle
edge-triggered interrupts. It fails to ensure all interrupt status bits are
cleared, which works with level-triggered interrupts but not the
edge-triggered interrupts typical from using MSI.
To fix this problem, check if the driver may have raced with the hardware
setting additional interrupt status bits and clear status until it is in a
stable state.
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Link: https://lore.kernel.org/r/20210715213744.GA44506@redhat
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar as with tcpm this patch lets fw_devlink know not to wait on the
fwnode to be populated as a struct device.
Without this patch, USB functionality can be broken on some previously
supported boards.
Fixes: 28ec344bb8 ("usb: typec: tcpm: Don't block probing of consumers of "connector" nodes")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Link: https://lore.kernel.org/r/20210714061807.5737-1-martin.kepplinger@puri.sm
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.
When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.
To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.
checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.
If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.
CPU0 CPU1
(hub thread) (xhci event handler)
xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()
Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d143825baf.
Justin reports some of his systems now fail as result of this commit:
xhci_hcd 0000:04:00.0: Direct firmware load for renesas_usb_fw.mem failed with error -2
xhci_hcd 0000:04:00.0: request_firmware failed: -2
xhci_hcd: probe of 0000:04:00.0 failed with error -2
The revert brings back the original issue the commit tried to solve but
at least unbreaks existing systems relying on previous behavior.
Cc: stable@vger.kernel.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Justin Forbes <jmforbes@linuxtx.org>
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Fixes: d143825baf ("usb: renesas-xhci: Fix handling of unknown ROM state")
Link: https://lore.kernel.org/r/20210719070519.41114-1-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix comments for GE CS1000 CP210x USB ID assignments.
Fixes: 42213a0190 ("USB: serial: cp210x: add some more GE USB IDs")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix the following fallthrough warning (powerpc-randconfig):
drivers/usb/gadget/udc/fsl_qe_udc.c:589:4: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/60ef0750.I8J+C6KAtb0xVOAa%25lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
When the user submits a control URB via usbfs, the user supplies the
bRequestType value and the kernel uses it to compute the pipe value.
However, do_proc_control() performs this computation incorrectly in
the case where the bRequestType direction bit is set to USB_DIR_IN and
the URB's transfer length is 0: The pipe's direction is also set to IN
but it should be OUT, which is the direction the actual transfer will
use regardless of bRequestType.
Commit 5cc59c418f ("USB: core: WARN if pipe direction != setup
packet direction") added a check to compare the direction bit in the
pipe value to a control URB's actual direction and to WARN if they are
different. This can be triggered by the incorrect computation
mentioned above, as found by syzbot.
This patch fixes the computation, thus avoiding the WARNing.
Reported-and-tested-by: syzbot+72af3105289dcb4c055b@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210712185436.GB326369@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch is meant to support LARA-R6 Cat 1 module family.
Module USB ID:
Vendor ID: 0x05c6
Product ID: 0x90fA
Interface layout:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: QMI wwan (not available in all versions)
Signed-off-by: Marco De Marco <marco.demarco@posteo.net>
Link: https://lore.kernel.org/r/49260184.kfMIbaSn9k@mars
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
In order to take advantage of the TX fifo resizing logic, manually add
these properties to the DWC3 child node by default. This will allow
the DWC3 gadget to resize the TX fifos for the IN endpoints, which
help with performance.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1625908395-5498-6-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have USB compositions which may require multiple endpoints
that support EP bursting. HW defined TX FIFO sizes may not always be
sufficient for these compositions. By utilizing flexible TX FIFO
allocation, this allows for endpoints to request the required FIFO depth to
achieve higher bandwidth. With some higher bMaxBurst configurations, using
a larger TX FIFO size results in better TX throughput.
By introducing the check_config() callback, the resizing logic can fetch
the maximum number of endpoints used in the USB composition (can contain
multiple configurations), which helps ensure that the resizing logic can
fulfill the configuration(s), or return an error to the gadget layer
otherwise during bind time.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1625908395-5498-4-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the USB gadget is able to support the configuration being
added based on the number of endpoints required from all interfaces. This
is for accounting for any bandwidth or space limitations.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1625908395-5498-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UDCs may have constraints on how many high bandwidth endpoints it can
support in a certain configuration. This API allows for the composite
driver to pass down the total number of endpoints to the UDC so it can verify
it has the required resources to support the configuration.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1625908395-5498-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
- Added option for per CPU threads to the hwlat tracer
- Have hwlat tracer handle hotplug CPUs
- New tracer: osnoise, that detects latency caused by interrupts, softirqs
and scheduling of other tasks.
- Added timerlat tracer that creates a thread and measures in detail what
sources of latency it has for wake ups.
- Removed the "success" field of the sched_wakeup trace event.
This has been hardcoded as "1" since 2015, no tooling should be looking
at it now. If one exists, we can revert this commit, fix that tool and
try to remove it again in the future.
- tgid mapping fixed to handle more than PID_MAX_DEFAULT pids/tgids.
- New boot command line option "tp_printk_stop", as tp_printk causes trace
events to write to console. When user space starts, this can easily live
lock the system. Having a boot option to stop just after boot up is
useful to prevent that from happening.
- Have ftrace_dump_on_oops boot command line option take numbers that match
the numbers shown in /proc/sys/kernel/ftrace_dump_on_oops.
- Bootconfig clean ups, fixes and enhancements.
- New ktest script that tests bootconfig options.
- Add tracepoint_probe_register_may_exist() to register a tracepoint
without triggering a WARN*() if it already exists. BPF has a path from
user space that can do this. All other paths are considered a bug.
- Small clean ups and fixes
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYN8YPhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhxLAP9Mo5hHv7Hg6W7Ddv77rThm+qclsMR/
yW0P+eJpMm4+xAD8Cq03oE1DimPK+9WZBKU5rSqAkqG6CjgDRw6NlIszzQQ=
=WEPR
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Added option for per CPU threads to the hwlat tracer
- Have hwlat tracer handle hotplug CPUs
- New tracer: osnoise, that detects latency caused by interrupts,
softirqs and scheduling of other tasks.
- Added timerlat tracer that creates a thread and measures in detail
what sources of latency it has for wake ups.
- Removed the "success" field of the sched_wakeup trace event. This has
been hardcoded as "1" since 2015, no tooling should be looking at it
now. If one exists, we can revert this commit, fix that tool and try
to remove it again in the future.
- tgid mapping fixed to handle more than PID_MAX_DEFAULT pids/tgids.
- New boot command line option "tp_printk_stop", as tp_printk causes
trace events to write to console. When user space starts, this can
easily live lock the system. Having a boot option to stop just after
boot up is useful to prevent that from happening.
- Have ftrace_dump_on_oops boot command line option take numbers that
match the numbers shown in /proc/sys/kernel/ftrace_dump_on_oops.
- Bootconfig clean ups, fixes and enhancements.
- New ktest script that tests bootconfig options.
- Add tracepoint_probe_register_may_exist() to register a tracepoint
without triggering a WARN*() if it already exists. BPF has a path
from user space that can do this. All other paths are considered a
bug.
- Small clean ups and fixes
* tag 'trace-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (49 commits)
tracing: Resize tgid_map to pid_max, not PID_MAX_DEFAULT
tracing: Simplify & fix saved_tgids logic
treewide: Add missing semicolons to __assign_str uses
tracing: Change variable type as bool for clean-up
trace/timerlat: Fix indentation on timerlat_main()
trace/osnoise: Make 'noise' variable s64 in run_osnoise()
tracepoint: Add tracepoint_probe_register_may_exist() for BPF tracing
tracing: Fix spelling in osnoise tracer "interferences" -> "interference"
Documentation: Fix a typo on trace/osnoise-tracer
trace/osnoise: Fix return value on osnoise_init_hotplug_support
trace/osnoise: Make interval u64 on osnoise_main
trace/osnoise: Fix 'no previous prototype' warnings
tracing: Have osnoise_main() add a quiescent state for task rcu
seq_buf: Make trace_seq_putmem_hex() support data longer than 8
seq_buf: Fix overflow in seq_buf_putmem_hex()
trace/osnoise: Support hotplug operations
trace/hwlat: Support hotplug operations
trace/hwlat: Protect kdata->kthread with get/put_online_cpus
trace: Add timerlat tracer
trace: Add osnoise tracer
...
This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers. The major core change is a rework
to drop the status byte handling macros and the old bit shifted
definitions and the rest of the updates are minor fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYN7I6iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXpRAQCkngYZ
35yQrqOxgOk2pfrysE95tHrV1MfJm2U49NFTwAEAuZutEvBUTfBF+sbcJ06r6q7i
H0hkJN/Io7enFs5v3WA=
=zwIa
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers.
The major core change is a rework to drop the status byte handling
macros and the old bit shifted definitions and the rest of the updates
are minor fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (287 commits)
scsi: aha1740: Avoid over-read of sense buffer
scsi: arcmsr: Avoid over-read of sense buffer
scsi: ips: Avoid over-read of sense buffer
scsi: ufs: ufs-mediatek: Add missing of_node_put() in ufs_mtk_probe()
scsi: elx: libefc: Fix IRQ restore in efc_domain_dispatch_frame()
scsi: elx: libefc: Fix less than zero comparison of a unsigned int
scsi: elx: efct: Fix pointer error checking in debugfs init
scsi: elx: efct: Fix is_originator return code type
scsi: elx: efct: Fix link error for _bad_cmpxchg
scsi: elx: efct: Eliminate unnecessary boolean check in efct_hw_command_cancel()
scsi: elx: efct: Do not use id uninitialized in efct_lio_setup_session()
scsi: elx: efct: Fix error handling in efct_hw_init()
scsi: elx: efct: Remove redundant initialization of variable lun
scsi: elx: efct: Fix spelling mistake "Unexected" -> "Unexpected"
scsi: lpfc: Fix build error in lpfc_scsi.c
scsi: target: iscsi: Remove redundant continue statement
scsi: qla4xxx: Remove redundant continue statement
scsi: ppa: Switch to use module_parport_driver()
scsi: imm: Switch to use module_parport_driver()
scsi: mpt3sas: Fix error return value in _scsih_expander_add()
...
Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener
to another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance
(for pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require
jump labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast address
allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks
in NAPI context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and NXP
(our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm 60GHz WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LvtX
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener to
another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance (for
pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require jump
labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast
address allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks in NAPI
context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and
NXP (our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support"
* tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2168 commits)
tcp: change ICSK_CA_PRIV_SIZE definition
tcp_yeah: check struct yeah size at compile time
gve: DQO: Fix off by one in gve_rx_dqo()
stmmac: intel: set PCI_D3hot in suspend
stmmac: intel: Enable PHY WOL option in EHL
net: stmmac: option to enable PHY WOL with PMT enabled
net: say "local" instead of "static" addresses in ndo_dflt_fdb_{add,del}
net: use netdev_info in ndo_dflt_fdb_{add,del}
ptp: Set lookup cookie when creating a PTP PPS source.
net: sock: add trace for socket errors
net: sock: introduce sk_error_report
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
net: dsa: include fdb entries pointing to bridge in the host fdb list
net: dsa: include bridge addresses which are local in the host fdb list
net: dsa: sync static FDB entries on foreign interfaces to hardware
net: dsa: install the host MDB and FDB entries in the master's RX filter
net: dsa: reference count the FDB addresses at the cross-chip notifier level
net: dsa: introduce a separate cross-chip notifier type for host FDBs
net: dsa: reference count the MDB entries at the cross-chip notifier level
...
The __assign_str macro has an unusual ending semicolon but the vast
majority of uses of the macro already have semicolon termination.
$ git grep -P '\b__assign_str\b' | wc -l
551
$ git grep -P '\b__assign_str\b.*;' | wc -l
480
Add semicolons to the __assign_str() uses without semicolon termination
and all the other uses without semicolon termination via additional defines
that are equivalent to __assign_str() with the eventual goal of removing
the semicolon from the __assign_str() macro definition.
Link: https://lore.kernel.org/lkml/1e068d21106bb6db05b735b4916bb420e6c9842a.camel@perches.com/
Link: https://lkml.kernel.org/r/48a056adabd8f70444475352f617914cef504a45.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-----BEGIN PGP SIGNATURE-----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=Oa1c
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Add %pt[RT]s modifier to vsprintf(). It overrides ISO 8601 separator
by using ' ' (space). It produces "YYYY-mm-dd HH:MM:SS" instead of
"YYYY-mm-ddTHH:MM:SS".
- Correctly parse long row of numbers by sscanf() when using the field
width. Add extensive sscanf() selftest.
- Generalize re-entrant CPU lock that has already been used to
serialize dump_stack() output. It is part of the ongoing printk
rework. It will allow to remove the obsoleted printk_safe buffers and
introduce atomic consoles.
- Some code clean up and sparse warning fixes.
* tag 'printk-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: fix cpu lock ordering
lib/dump_stack: move cpu lock to printk.c
printk: Remove trailing semicolon in macros
random32: Fix implicit truncation warning in prandom_seed_state()
lib: test_scanf: Remove pointless use of type_min() with unsigned types
selftests: lib: Add wrapper script for test_scanf
lib: test_scanf: Add tests for sscanf number conversion
lib: vsprintf: Fix handling of number field widths in vsscanf
lib: vsprintf: scanf: Negative number must have field width > 1
usb: host: xhci-tegra: Switch to use %ptTs
nilfs2: Switch to use %ptTs
kdb: Switch to use %ptTs
lib/vsprintf: Allow to override ISO 8601 date and time separator
- Changes to core scheduling facilities:
- Add "Core Scheduling" via CONFIG_SCHED_CORE=y, which enables
coordinated scheduling across SMT siblings. This is a much
requested feature for cloud computing platforms, to allow
the flexible utilization of SMT siblings, without exposing
untrusted domains to information leaks & side channels, plus
to ensure more deterministic computing performance on SMT
systems used by heterogenous workloads.
There's new prctls to set core scheduling groups, which
allows more flexible management of workloads that can share
siblings.
- Fix task->state access anti-patterns that may result in missed
wakeups and rename it to ->__state in the process to catch new
abuses.
- Load-balancing changes:
- Tweak newidle_balance for fair-sched, to improve
'memcache'-like workloads.
- "Age" (decay) average idle time, to better track & improve workloads
such as 'tbench'.
- Fix & improve energy-aware (EAS) balancing logic & metrics.
- Fix & improve the uclamp metrics.
- Fix task migration (taskset) corner case on !CONFIG_CPUSET.
- Fix RT and deadline utilization tracking across policy changes
- Introduce a "burstable" CFS controller via cgroups, which allows
bursty CPU-bound workloads to borrow a bit against their future
quota to improve overall latencies & batching. Can be tweaked
via /sys/fs/cgroup/cpu/<X>/cpu.cfs_burst_us.
- Rework assymetric topology/capacity detection & handling.
- Scheduler statistics & tooling:
- Disable delayacct by default, but add a sysctl to enable
it at runtime if tooling needs it. Use static keys and
other optimizations to make it more palatable.
- Use sched_clock() in delayacct, instead of ktime_get_ns().
- Misc cleanups and fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=3VDr
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2021-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler udpates from Ingo Molnar:
- Changes to core scheduling facilities:
- Add "Core Scheduling" via CONFIG_SCHED_CORE=y, which enables
coordinated scheduling across SMT siblings. This is a much
requested feature for cloud computing platforms, to allow the
flexible utilization of SMT siblings, without exposing untrusted
domains to information leaks & side channels, plus to ensure more
deterministic computing performance on SMT systems used by
heterogenous workloads.
There are new prctls to set core scheduling groups, which allows
more flexible management of workloads that can share siblings.
- Fix task->state access anti-patterns that may result in missed
wakeups and rename it to ->__state in the process to catch new
abuses.
- Load-balancing changes:
- Tweak newidle_balance for fair-sched, to improve 'memcache'-like
workloads.
- "Age" (decay) average idle time, to better track & improve
workloads such as 'tbench'.
- Fix & improve energy-aware (EAS) balancing logic & metrics.
- Fix & improve the uclamp metrics.
- Fix task migration (taskset) corner case on !CONFIG_CPUSET.
- Fix RT and deadline utilization tracking across policy changes
- Introduce a "burstable" CFS controller via cgroups, which allows
bursty CPU-bound workloads to borrow a bit against their future
quota to improve overall latencies & batching. Can be tweaked via
/sys/fs/cgroup/cpu/<X>/cpu.cfs_burst_us.
- Rework assymetric topology/capacity detection & handling.
- Scheduler statistics & tooling:
- Disable delayacct by default, but add a sysctl to enable it at
runtime if tooling needs it. Use static keys and other
optimizations to make it more palatable.
- Use sched_clock() in delayacct, instead of ktime_get_ns().
- Misc cleanups and fixes.
* tag 'sched-core-2021-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/doc: Update the CPU capacity asymmetry bits
sched/topology: Rework CPU capacity asymmetry detection
sched/core: Introduce SD_ASYM_CPUCAPACITY_FULL sched_domain flag
psi: Fix race between psi_trigger_create/destroy
sched/fair: Introduce the burstable CFS controller
sched/uclamp: Fix uclamp_tg_restrict()
sched/rt: Fix Deadline utilization tracking during policy change
sched/rt: Fix RT utilization tracking during policy change
sched: Change task_struct::state
sched,arch: Remove unused TASK_STATE offsets
sched,timer: Use __set_current_state()
sched: Add get_current_state()
sched,perf,kvm: Fix preemption condition
sched: Introduce task_is_running()
sched: Unbreak wakeups
sched/fair: Age the average idle time
sched/cpufreq: Consider reduced CPU capacity in energy calculation
sched/fair: Take thermal pressure into account while estimating energy
thermal/cpufreq_cooling: Update offline CPUs per-cpu thermal_pressure
sched/fair: Return early from update_tg_cfs_load() if delta == 0
...
The device (32a7:0000 Heimann Sensor GmbH USB appset demo) claims to be
a CDC-ACM device in its descriptors but in fact is not. If it is run
with echo disabled it returns garbled data, probably due to something
that happens in the TTY layer. And when run with echo enabled (the
default), it will mess up the calibration data of the sensor the first
time any data is sent to the device.
In short, I had a bad time after connecting the sensor and trying to get
it to work. I hope blacklisting it in the cdc-acm driver will save
someone else a bit of trouble.
Signed-off-by: Hannu Hartikainen <hannu@hrtk.in>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210622141454.337948-1-hannu@hrtk.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is used to relax bandwidth schedule by allowing multiple
Start-Split in the same microframe.
Reviewed-and-Tested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623995165-25759-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The continue statement at the end of the while-loop is redundant,
remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Continue has no effect")
Link: https://lore.kernel.org/r/20210621095545.9659-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "rv" is initialized to "-ENOMEM", because "rv" is re-assigned to
"-EINVAL", when kmalloc & usb_alloc_urb failed, the return value should
return "-ENOMEM" rather than "-EINVAL",so the "rv" assignment is placed
in the position where usb_endpoint_is_int_in is false.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210621132415.2341-1-angkery@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.14-rc1, including:
- gpio support for CP2108
- chars_in_buffer and write_room return-value updates
- chars_in_buffer and write_room clean ups
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYNRHtQAKCRALxc3C7H1l
CD96AQDYFm0ssrdV61bejQLX+9LrIfNuISXNJy9cLhCxi3ZYJwD/ZLJhz0K/Xby1
+Xm4J5UVbPuIKMkNKMc0ezH0XZfURwU=
=61V6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.14-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.14-rc1
Here are the USB-serial updates for 5.14-rc1, including:
- gpio support for CP2108
- chars_in_buffer and write_room return-value updates
- chars_in_buffer and write_room clean ups
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.14-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add support for GPIOs on CP2108
USB: serial: drop irq-flags initialisations
USB: serial: mos7840: drop buffer-callback return-value comments
USB: serial: mos7720: drop buffer-callback sanity checks
USB: serial: io_edgeport: drop buffer-callback sanity checks
USB: serial: digi_acceleport: add chars_in_buffer locking
USB: serial: digi_acceleport: reduce chars_in_buffer over-reporting
USB: serial: make usb_serial_driver::chars_in_buffer return uint
USB: serial: make usb_serial_driver::write_room return uint
The continue statement at the end of a for-loop has no effect,
remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Continue has no effect")
Cc: Mathias Nyman <mathias.nyman@intel.com>
Link: https://lore.kernel.org/r/20210618090447.99114-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creation EP's debugfs called earlier than debugfs folder for dwc3
device created. As result EP's debugfs are created in '/sys/kernel/debug'
instead of '/sys/kernel/debug/usb/dwc3.1.auto'.
Moved dwc3_debugfs_init() function call before calling
dwc3_core_init_mode() to allow create dwc3 debugfs parent before
creating EP's debugfs's.
Fixes: 8d396bb0a5 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/01fafb5b2d8335e98e6eadbac61fc796bdf3ec1a.1623948457.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the error handling
case instead of 0.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210618043835.2641360-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when receive eem echo command, it will send a response,
but queue this response to the usb request which allocate
from gadget device endpoint zero,
and transmit the request to IN endpoint of eem interface.
on dwc3 gadget, it will trigger following warning in function
__dwc3_gadget_ep_queue(),
if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
&req->request, req->dep->name))
return -EINVAL;
fix it by allocating a usb request from IN endpoint of eem interface,
and transmit the usb request to same IN endpoint of eem interface.
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210616115142.34075-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running sparse checker it shows warning message about
incorrect endianness used for descriptor initialization:
| f_hid.c:91:43: warning: incorrect type in initializer (different base types)
| f_hid.c:91:43: expected restricted __le16 [usertype] bcdHID
| f_hid.c:91:43: got int
Fixing issue with cpu_to_le16() macro, however this is not a real issue
as the value is the same both endians.
Cc: Fabien Chouteau <fabien.chouteau@barco.com>
Cc: Segiy Stetsyuk <serg_stetsuk@ukr.net>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/20210617162755.29676-1-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmDNsqYACgkQSFkpgVDW
cbt6Gwf/YfxvGlKDS97UV9Iy4N24h451CbBsWuRKcHD+RFngaeF9uJuTZ+ki/AFR
CQOdXKbxpnnahGH7+yalmJ3Du49xMGaXkkaABT5HisY0QNtJeuXa6Dg10+yE5O0M
hPzl+zRpYIwYL2b9DG5RlK27y70lrsNfYoD0eddspOSMJo2ol6q4N2bOnfdWLCmE
xq5WsbOG+a+43O23QgtW6Jk8GpmlBNvVkU4x2WALKZG/Z6oCgDqxFrUJJjHk0li5
nCVPV3n9hpNpKU462uHo+frlG3WTjjeL6qyqQEc/WE+Bzh+FaTXQg+rnlg1e8M0K
AYGM9mq7Dkl7Cc+TjFqIeSWPTO5zOw==
=Ljxm
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Some tiny improvements for cdns USB3 drivers, no important things.
* tag 'usb-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdns3: cdns3-gadget: Use list_move_tail instead of list_del/list_add_tail
doc: dt-binding: cdns,usb3: Add interrupt-names property under required
usb: cdnsp: Useless condition has been removed
usb: cdns3: Corrected comment to align with kernel-doc comment
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDPuyMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvxgH/RKvSuRPwkJ2Jcp9
VLi5kCbqtJlYLq6tB6peSJ8otKgxkcRwC0pIY4LlYIAWYboktLQ5RKp/9nB2h2FN
aMZUMu6AI/lVJyFMI5MnKnJIUiUq+WXR3lSSlw68vwFLFdzqUZFNq+bqeiVvnIy1
yqA6naj24Tu/RbYffQoPvdSJcU2SLXRMxwD8HRGiU2d51RaFsOvsZvF+P5TVcsEV
ZmttJeER21CaI/A809eqaFmyGrUOcZZK9roZEbMwanTZOMw18biEsLu/UH4kBX01
JC4+RlGxcWjQ5YNZgChsgoOK/CHzc6ITztTntdeDWAvwZjQFzV7pCy4/3BWne3O+
5178yHM=
=o8cN
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc7' into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove broken task->state references and let wake_up_process() DTRT.
The anti-pattern in these patches breaks the ordering of ->state vs
COND as described in the comment near set_current_state() and can lead
to missed wakeups:
(OoO load, observes RUNNING)<-.
for (;;) { |
t->state = UNINTERRUPTIBLE; |
smp_mb(); ,-----> | (observes !COND)
| /
if (COND) ---------' | COND = 1;
break; `- if (t->state != RUNNING)
wake_up_process(t); // not done
schedule(); // forever waiting
}
t->state = TASK_RUNNING;
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210611082838.160855222@infradead.org
This reverts commit b4e326165e as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c950686b38 as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.
We got following bug when system resumes from s4:
kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S W 5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c
Call trace:
__slab_free+0x5c/0x424
kfree+0x30c/0x32c
xhci_mem_cleanup+0x394/0x3cc
xhci_mem_init+0x9ac/0x1070
xhci_init+0x8c/0x1d0
xhci_resume+0x1cc/0x5fc
xhci_plat_resume+0x64/0x70
platform_pm_thaw+0x28/0x60
dpm_run_callback+0x54/0x24c
device_resume+0xd0/0x200
async_resume+0x24/0x60
async_run_entry_fn+0x44/0x110
process_one_work+0x1f0/0x490
worker_thread+0x5c/0x450
kthread+0x158/0x160
ret_from_fork+0x10/0x24
Original patch that caused this issue was backported to 4.4 stable,
so this should be backported to 4.4 stabe as well.
Fixes: cf0ee7c60c ("xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Tao Xue <xuetao09@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the urb->actual_length to bytes successfully copied in case all bytes
weren't copied from a temporary buffer to the URB sg list.
Also print a debug message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save a bit of power by not interrupting so often by default if
XHCI_AVOID_BEI quirk is set.
In normal cases the xhci driver will only generate an interrupt on the last
isochronous TRB of an URB. In a common UVC webcam usecase there are 32 TRBs
per URB.
if AVOID_BEI flag is set then xhci driver will force an interrupt every 8th
isoc TRB to make sure the event ring doesn't get too full.
This is however way too frequent in common single webcam use cases, causing
1000 interrupts/sec and thus poor powermanagement performance.
Instead start with interrupting every 32 isoc TRB, and halve it in case
event ring becomes half-full. Stop halving when reaching a rate of every
8th trb.
This is a one way solution. If interrupt rate is increased it will stay
high until driver is reloaded. The highest rate is the same as the old
default rate.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want those around confusing people.
ERST_NUM_SEGS is used both when allocating event ring segments, and when
allocating entries in the event ring segment table (erst).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
typec_register_altmode() misses to call altmode_id_remove() in an error
path. Add the missed function call to fix it.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Link: https://lore.kernel.org/r/20210617073226.47599-1-jingxiangfeng@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the voltage is being decreased in power negotiation, the Source will
set the power supply to operate at the new voltage level before sending
PS_RDY. Relax the threshold before sending Request Message so that it
will not race with Source which begins to adjust the voltage right after
it sends Accept Message (PPS) or tSrcTransition (25~35ms) after it sends
Accept Message (non-PPS).
The real threshold will be set after Sink receives PS_RDY Message.
Fixes: f321a02cae ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Cc: stable <stable@vger.kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210616090102.1897674-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In PR_SWAP_SNK_SRC_SOURCE_ON state, Vsafe0v is expected as well so do
nothing here to avoid state machine going into SNK_UNATTACHED.
Fixes: 28b43d3d74 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210615173206.1646477-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Table 4-3 VBUS Sink Characteristics" of "Type-C Cable and Connector
Specification" defines the disconnect voltage thresholds of various
configurations. This change fixes the disconnect threshold voltage
calculation based on vSinkPD_min and vSinkDisconnectPD as defined
by the table.
Fixes: e1a97bf80a ("usb: typec: tcpci: Implement Auto discharge disconnect callbacks")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210615174323.1160132-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The continue statement at the end of a for-loop has no effect,
remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Continue has no effect")
Link: https://lore.kernel.org/r/20210617112638.9072-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are continue statements at the end of loops that have
no effect and are redundant. Remove them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Continue has no effect")
Link: https://lore.kernel.org/r/20210617123826.13764-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. of_node_put() on it before exitting
this function.
Fixes: 971ee24706 ("usb: xhci: tegra: Enable ELPG for runtime/system PM")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210616044519.2183826-2-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto put_padctl to put refcount of device on error in tegra_xusb_probe()
Fixes: 971ee24706 ("usb: xhci: tegra: Enable ELPG for runtime/system PM")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210616044519.2183826-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ROM load sometimes seems to return an unknown status
(RENESAS_ROM_STATUS_NO_RESULT) instead of success / fail.
If the ROM load indeed failed this leads to failures when trying to
communicate with the controller later on.
Attempt to load firmware using RAM load in those cases.
Fixes: 2478be82de ("usb: renesas-xhci: Add ROM loader for uPD720201")
Cc: stable@vger.kernel.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Link: https://lore.kernel.org/r/20210615153758.253572-1-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to some other CP210x device types, CP2108 has a number of GPIO
pins that can be exposed through gpiolib.
CP2108 has four serial interfaces but only one set of GPIO pins, which
is modelled as a single gpio chip and registered as a child of the first
interface.
CP2108 has 16 GPIOs so the width of the state variables needs to be
extended to 16 bits and this is also reflected in the control requests.
Like CP2104, CP2108 have GPIO pins with configurable alternate
functions and pins unavailable for GPIO use are determined and reported
to gpiolib at probe.
Signed-off-by: Pho Tran <pho.tran@silabs.com>
Co-developed-by: Tung Pham <tung.pham@silabs.com>
Signed-off-by: Tung Pham <tung.pham@silabs.com>
[ johan: rewrite gpio get() and set(); misc cleanups; amend commit
message ]
Link: https://lore.kernel.org/r/20210610132844.25495-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmDJT3gACgkQSFkpgVDW
cbvh6QgAucjmka2WfiFraPRij4SyveqgTUQtmjLWhNcVugla6eHJTmsRlTvqj3YT
zBRv418FRQZmbwojOM/Vai49qcG+/nJGJDAupQ5v+tUmtzb0BIyNSxLnBpgrspFK
8qBUA3lF7JLz4xsXwICNLNvvvcCPjYOVfk3430FpkythJIK5UCFidkrUB2S/p6/1
OpzWMICZxv4kdSxf7EkfOhjbfzqJZcJZR+sDjYNnOA4gLGClkE0OQC9k+qIpIEDs
UHxtL0fmToW0EOv/14SBRVTlfqKH5WgEUDlodNw7wVYSfMx1NoU2UgwcytD2SZX8
7dcDhvuT2YZv/HuV83vYAgN5hJRCmQ==
=Drqs
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One bug fix for USB charger detection at imx7d and imx8m series SoCs
* tag 'usb-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: Fix Battery Charger 1.2 CDP detection
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org>
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Call onboard_hub_create/destroy_pdevs() from _probe()/_remove()
to create/destroy platform devices for onboard USB hubs that may
be connected to the root hub of the controller. These functions
are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct xhci_hcd to keep track of the onboard hub
platform devices that are owned by the xHCI.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.4.I7a3a7d9d2126c34079b1cab87aa0b2ec3030f9b7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub (through xhci-plat), support for other configurations
could be added if needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use common helper ssusb_set_mode() to do role switch instead
of manual switch helper;
Remove unnecessary local variable when get role status
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-14-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now we mainly use usb-role-switch to set dual role mode, and all
three ways supported use the same function to switch mode, use
usb_role enum will make code clear
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When power down device IP, we can also power down device port,
then power on the port again when power on device ip, it's helpful
to make device ip enter ip sleep mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove attribution to retval before check, which make it completely
meaningless, and does't check what it was supposed: the return
value of the timed function to set up configuration flag.
Fixes: 60d789f3bf ("usb: isp1760: add support for isp1763")
Tested-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Tong Tiangen <tongtiangen@huawei.com>
Link: https://lore.kernel.org/r/20210611014055.68551-1-tongtiangen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous
commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use.
The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN
needs to be in place of it. We don't utilize B-sensors in the driver,
so it never was a problem, nevertheless let's correct the definition of
the bits.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices need an extra delay after losing VBUS, otherwise VBUS may
be detected as active at suspend time, preventing the PHY's suspension
by the VBUS detection sensor. This problem was found on Asus Transformer
TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately
from suspend because VBUS sensor continues to detect VBUS as active after
disconnection. We need to poll the PHY's VBUS wakeup status until it's
deasserted before suspending PHY in order to fix this minor trouble.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Reported-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the previous patch, we introduced tty_get_char_size() and
tty_get_frame_size() for computing character and frame sizes,
respectively. Here, we make use of them in various tty drivers where
applicable.
The stats look nice: 12 insertions, 169 deletions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alex Elder <elder@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make data_bits what it really is. Assign proper bit counts to data_bits
instead of magic 0..3. There are two reasons:
1) it's clear what we store there, and
2) it will make the transition to tty_tty_get_char_size() in the next
patch easier.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a390bef7db ("usb: gadget: fsl_mxc_udc: Remove the driver")
didn't remove all the MXC related stuff which can cause build problem
for LS1021 when enabled again in Kconfig. This patch remove all the
remnants.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20210612003128.372238-1-leoyang.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devctl register on musb is the only way to get state information
on musb. The hardware can easily get confused because it tries to do
things on it's own automagically, and things like slow VBUS rise can
make things fail.
Let's make it easier to debug the ongoing state change issues that
keep popping up on regular basis and add tracing support.
With these changes we can easily trace musb state change events with:
echo 1 > /sys/kernel/debug/tracing/events/musb/musb_state/enable
cat /sys/kernel/debug/tracing/trace_pipe
echo 0 > /sys/kernel/debug/tracing/events/musb/musb_state/enable
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Bhushan Shah <bshah@kde.org>
Cc: Drew Fustini <drew@beagleboard.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210604080536.12185-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify cable state handling a bit to leave out duplicated code.
We are just scheduling work and showing state info if a recheck is
needed. No intended functional changes.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Bhushan Shah <bshah@kde.org>
Cc: Drew Fustini <drew@beagleboard.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210604080536.12185-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into usb-next
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit implements the complete programming sequence for ELPG
entry and exit.
1. At ELPG entry, invokes tegra_xusb_padctl_enable_phy_sleepwalk()
and tegra_xusb_padctl_enable_phy_wake() to configure XUSB PADCTL
sleepwalk and wake detection circuits to maintain USB lines level
and respond to wake events (wake-on-connect, wake-on-disconnect,
device-initiated-wake).
2. At ELPG exit, invokes tegra_xusb_padctl_disable_phy_sleepwalk()
and tegra_xusb_padctl_disable_phy_wake() to disarm sleepwalk and
wake detection circuits.
At runtime suspend, XUSB host controller can enter ELPG to reduce
power consumption. When XUSB PADCTL wake detection circuit detects
a wake event, an interrupt will be raised. xhci-tegra driver then
will invoke pm_runtime_resume() for xhci-tegra.
Runtime resume could also be triggered by protocol drivers, this is
the host-initiated-wake event. At runtime resume, xhci-tegra driver
brings XUSB host controller out of ELPG to handle the wake events.
The same ELPG enter/exit procedure will be performed for system
suspend/resume path so USB devices can remain connected across SC7.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit unlinks xhci-tegra platform device with SS/host power
domain devices. Reasons for this change is - at ELPG entry, PHY
sleepwalk and wake configuration need to be done before powering
down SS/host partitions, and PHY need be powered off after powering
down SS/host partitions. Sequence looks like roughly below:
tegra_xusb_enter_elpg() -> xhci_suspend()
-> enable PHY sleepwalk and wake if needed
-> power down SS/host partitions
-> power down PHY
If SS/host power domains are linked to xhci-tegra platform device, we
are not able to perform the sequence like above.
This commit introduces:
1. tegra_xusb_unpowergate_partitions() to power up SS and host
partitions together. If SS/host power domain devices are
available, it invokes pm_runtime_get_sync() to request power
driver to power up partitions; If power domain devices are not
available, tegra_powergate_sequence_power_up() will be used to
power up partitions.
2. tegra_xusb_powergate_partitions() to power down SS and host
partitions together. If SS/host power domain devices are
available, it invokes pm_runtime_put_sync() to request power
driver to power down partitions; If power domain devices are not
available, tegra_powergate_power_off() will be used to power down
partitions.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Here are two fixes for the cp210x driver. The first fixes a regression
with early revisions of the CP2102N which specifically broke some ESP32
development boards. The second makes sure that the pin configuration is
detected properly also for the CP2102N QFN20 package.
Both have been in linux-next over night and with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYMM1XQAKCRALxc3C7H1l
CH1DAQDlY9HI8ujDidiFHqBw/UduU7jmncuiGR/sAVzEAstPigD/VOJH+cD/yn7Z
35gSi1DvdrBRjs8qTlzZvoiSN81nTgM=
=yLzP
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.13-rc6
Here are two fixes for the cp210x driver. The first fixes a regression
with early revisions of the CP2102N which specifically broke some ESP32
development boards. The second makes sure that the pin configuration is
detected properly also for the CP2102N QFN20 package.
Both have been in linux-next over night and with no reported issues.
* tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: fix CP2102N-A01 modem control
USB: serial: cp210x: fix alternate function for CP2102N QFN20
This reverts commit e0e8b6abe8.
Turns out this breaks the build. We had numerous reports of problems
from linux-next and 0-day about this not working properly, so revert it
for now until it can be figured out properly.
The build errors are:
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x29d4): undefined reference to `fsl_udc_clk_finalize'
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x2ba8): undefined reference to `fsl_udc_clk_release'
fsl_udc_core.c:(.text+0x2848): undefined reference to `fsl_udc_clk_init'
fsl_udc_core.c:(.text+0xe88): undefined reference to `fsl_udc_clk_release'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e0e8b6abe8 ("usb: gadget: fsl: Re-enable driver for ARM SoCs")
Cc: stable <stable@vger.kernel.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Leo Li <leoyang.li@nxp.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the copy-paste mistake in the return path of typec_mux_match(),
where dev is considered a member of struct typec_switch rather than
struct typec_mux.
The two structs are identical in regards to having the struct device as
the first entry, so this provides no functional change.
Fixes: 3370db3519 ("usb: typec: Registering real device entries for the muxes")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210610002132.3088083-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful. Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.
Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a390bef7db ("usb: gadget: fsl_mxc_udc: Remove the driver")
dropped the ARCH_MXC dependency from USB_FSL_USB2, leaving it depending
solely on FSL_SOC.
FSL_SOC is powerpc only; it was briefly available on ARM in 2014 but was
removed by commit cfd074ad86 ("ARM: imx: temporarily remove
CONFIG_SOC_FSL from LS1021A"). Therefore the driver can no longer be
enabled on ARM platforms.
This appears to be a mistake as arm64's ARCH_LAYERSCAPE and arm32
SOC_LS1021A SoCs use this symbol. It's enabled in these defconfigs:
arch/arm/configs/imx_v6_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/arm/configs/multi_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mgcoge_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mpc512x_defconfig:CONFIG_USB_FSL_USB2=y
To fix, expand the dependencies so USB_FSL_USB2 can be enabled on the
ARM platforms, and with COMPILE_TEST.
Fixes: a390bef7db ("usb: gadget: fsl_mxc_udc: Remove the driver")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210610034957.93376-1-joel@jms.id.au
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As LKP noticed the Sparse is not happy about strict type handling:
.../typec/tcpm/wcove.c:380:50: sparse: expected unsigned short [usertype] header
.../typec/tcpm/wcove.c:380:50: sparse: got restricted __le16 const [usertype] header
Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt()
in the affected code.
Fixes: ae8a2ca8a2 ("usb: typec: Group all TCPCI/TCPM code together")
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210609172202.83377-1-andriy.shevchenko@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep around the debugfs "root" directory for the
dwc3 device. Instead, look it up anytime we need to find it. This will
help when callers get out-of-order and we had the potential to have a
"stale" pointer around for the root dentry, as has happened in the past.
Tested-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20210609093924.3293230-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).
A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.
Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.
Link: https://lore.kernel.org/r/20210609161509.9459-1-johan@kernel.org
Reported-by: David Frey <dpfrey@gmail.com>
Reported-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Tested-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Fixes: f61309d9c9 ("USB: serial: cp210x: set IXOFF thresholds")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
The QFN20 part has a different GPIO/port function assignment. The
configuration struct bit field ordered as TX/RX/RS485/WAKEUP/CLK
which exactly matches GPIO0-3 for QFN24/28. However, QFN20 has a
different GPIO to primary function assignment.
Special case QFN20 to follow to properly detect which GPIOs are
available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/r/51830b2b24118eb0f77c5c9ac64ffb2f519dbb1d.1622218300.git.stefan@agner.ch
Fixes: c8acfe0aad ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds interface between userspace and feedback endpoint to report real
feedback frequency to the Host.
Current implementation adds new userspace interface ALSA mixer control
"Capture Pitch 1000000" (similar to aloop driver's "PCM Rate Shift 100000"
mixer control)
Value in PPM is chosen to have correction value agnostic of the actual HW
rate, which the application is not necessarily dealing with, while still
retaining a good enough precision to allow smooth clock correction on the
playback side, if necessary.
Similar to sound/usb/endpoint.c, a slow down is allowed up to 25%. This
has no impact on the required bandwidth. Speedup correction has an impact
on the bandwidth reserved for the isochronous endpoint. The default
allowed speedup is 500ppm. This seems to be more than enough but, if
necessary, this is configurable through a module parameter. The reserved
bandwidth is rounded up to the next packet size.
Usage of this new control is easy to implement in existing userspace tools
like alsaloop from alsa-utils.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210603220104.1216001-4-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current f_uac2 USB OUT (aka 'capture') synchronization
implements 'ASYNC' scenario which means USB Gadget has
it's own freerunning clock and can update Host about
real clock frequency through feedback endpoint so Host
can align number of samples sent to the USB gadget to
prevent overruns/underruns
In case if Gadget can has no it's internal clock and
can consume audio samples at any rate (for example,
on the Gadget side someone records audio directly to
a file, or audio samples are played through an
external DAC as soon as they arrive), UAC2 spec
suggests 'ADAPTIVE' synchronization type.
Change UAC2 driver to make it configurable through
additional 'c_sync' configfs file.
Default remains 'asynchronous' with possibility to
switch it to 'adaptive'
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210603220104.1216001-3-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per USB and UAC2 specs, asynchronous audio sink endpoint
requires explicit synchronization mechanism (Isochronous
Feedback Endpoint)
Implement feedback companion endpoint for ISO OUT endpoint
This patch adds all required infrastructure and USB requests
handling for feedback endpoint. Syncrhonization itself is
still dummy (feedback ep always reports 'nomimal frequency'
e.g. no adjustement is needed). This satisfies hosts that
require feedback endpoint (like Win10) and poll it periodically
Actual synchronization mechanism should be implemented
separately
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210603220104.1216001-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every time the hub signals a reset while we (device) are hsotg->connected,
dwc2_hsotg_core_init_disconnected() is called, which in turn calls
dwc2_hs_phy_init().
GUSBCFG.USBTrdTim is cleared upon Core Soft Reset, so if
hsotg->params.phy_utmi_width is 8-bit, the value of GUSBCFG.USBTrdTim (the
default one: 0x5, corresponding to 16-bit) is always different from
hsotg->params.phy_utmi_width, thus dwc2_core_reset() is called every
time (usbcfg != usbcfg_old), which causes 2 issues:
1) The call to dwc2_core_reset() does another reset 300us after the initial
Chirp K of the first reset (which should last at least Tuch = 1ms), and
messes up the High-speed Detection Handshake: both hub and device drive
current into the D+ and D- lines at the same time.
2) GUSBCFG.USBTrdTim is cleared by the second reset, so its value is always
the default one (0x5).
Setting GUSBCFG.USBTrdTim after the potential call to dwc2_core_reset()
fixes both issues. It is now set even when select_phy is false because the
cost of the Core Soft Reset is removed.
Fixes: 1e868545f2 ("usb: dwc2: gadget: Move gadget phy init into core phy init")
Signed-off-by: Clément Lassieur <clement@lassieur.org>
Link: https://lore.kernel.org/r/20210603155921.940651-1-clement@lassieur.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the dwc3 platform driver does not explicitly ask for
a DMA mask. This makes it fall back to the default 32-bit mask which
breaks the driver on systems that only have RAM starting above the
first 4G like the Apple M1 SoC.
Fix this by calling dma_set_mask_and_coherent with a 64bit mask.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20210607061751.89752-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core has utility routines to retrieve various types of
descriptors. These routines will now provoke a WARN if they are asked
to retrieve 0 bytes (USB "receive" requests must not have zero
length), so avert this by checking the size argument at the start.
CC: Johan Hovold <johan@kernel.org>
Reported-and-tested-by: syzbot+7dbcd9ff34dc4ed45240@syzkaller.appspotmail.com
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210607152307.GD1768031@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Fixes: 517c4c44b3 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210605080914.2057758-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no validation of the index from dwc3_wIndex_to_dep() and we might
be referring a non-existing ep and trigger a NULL pointer exception. In
certain configurations we might use fewer eps and the index might wrongly
indicate a larger ep index than existing.
By adding this validation from the patch we can actually report a wrong
index back to the caller.
In our usecase we are using a composite device on an older kernel, but
upstream might use this fix also. Unfortunately, I cannot describe the
hardware for others to reproduce the issue as it is a proprietary
implementation.
[ 82.958261] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a4
[ 82.966891] Mem abort info:
[ 82.969663] ESR = 0x96000006
[ 82.972703] Exception class = DABT (current EL), IL = 32 bits
[ 82.978603] SET = 0, FnV = 0
[ 82.981642] EA = 0, S1PTW = 0
[ 82.984765] Data abort info:
[ 82.987631] ISV = 0, ISS = 0x00000006
[ 82.991449] CM = 0, WnR = 0
[ 82.994409] user pgtable: 4k pages, 39-bit VAs, pgdp = 00000000c6210ccc
[ 83.000999] [00000000000000a4] pgd=0000000053aa5003, pud=0000000053aa5003, pmd=0000000000000000
[ 83.009685] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[ 83.026433] Process irq/62-dwc3 (pid: 303, stack limit = 0x000000003985154c)
[ 83.033470] CPU: 0 PID: 303 Comm: irq/62-dwc3 Not tainted 4.19.124 #1
[ 83.044836] pstate: 60000085 (nZCv daIf -PAN -UAO)
[ 83.049628] pc : dwc3_ep0_handle_feature+0x414/0x43c
[ 83.054558] lr : dwc3_ep0_interrupt+0x3b4/0xc94
...
[ 83.141788] Call trace:
[ 83.144227] dwc3_ep0_handle_feature+0x414/0x43c
[ 83.148823] dwc3_ep0_interrupt+0x3b4/0xc94
[ 83.181546] ---[ end trace aac6b5267d84c32f ]---
Signed-off-by: Marian-Cristian Rotariu <marian.c.rotariu@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210608162650.58426-1-marian.c.rotariu@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when skb_clone() or skb_copy_expand() fail,
it should pull skb with lengh indicated by header,
or not it will read network data and check it as header.
Cc: <stable@vger.kernel.org>
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.com>
Link: https://lore.kernel.org/r/20210608233547.3767-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ACPI devices we have a symmetric API to put them, so use it in the driver.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210607205007.71458-3-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource() can return an error, add missed check for it.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210607205007.71458-2-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210607205007.71458-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the VDM responses couldn't be sent successfully, it doesn't need to
finish the AMS until the retry count reaches the limit.
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210606081452.764032-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_assign_descriptors() is called with 5 parameters,
the last 4 of which are the usb_descriptor_header for:
full-speed (USB1.1 - 12Mbps [including USB1.0 low-speed @ 1.5Mbps),
high-speed (USB2.0 - 480Mbps),
super-speed (USB3.0 - 5Gbps),
super-speed-plus (USB3.1 - 10Gbps).
The differences between full/high/super-speed descriptors are usually
substantial (due to changes in the maximum usb block size from 64 to 512
to 1024 bytes and other differences in the specs), while the difference
between 5 and 10Gbps descriptors may be as little as nothing
(in many cases the same tuning is simply good enough).
However if a gadget driver calls usb_assign_descriptors() with
a NULL descriptor for super-speed-plus and is then used on a max 10gbps
configuration, the kernel will crash with a null pointer dereference,
when a 10gbps capable device port + cable + host port combination shows up.
(This wouldn't happen if the gadget max-speed was set to 5gbps, but
it of course defaults to the maximum, and there's no real reason to
artificially limit it)
The fix is to simply use the 5gbps descriptor as the 10gbps descriptor,
if a 10gbps descriptor wasn't provided.
Obviously this won't fix the problem if the 5gbps descriptor is also
NULL, but such cases can't be so trivially solved (and any such gadgets
are unlikely to be used with USB3 ports any way).
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210609024459.1126080-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids a null pointer dereference in
f_{ecm,eem,hid,loopback,printer,rndis,serial,sourcesink,subset,tcm}
by simply reusing the 5gbps config for 10gbps.
Fixes: eaef50c760 ("usb: gadget: Update usb_assign_descriptors for SuperSpeedPlus")
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Michael R Sweet <msweet@msweet.org>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Cc: Wei Ming Chen <jj251510319013@gmail.com>
Cc: Will McVicker <willmcvicker@google.com>
Cc: Zqiang <qiang.zhang@windriver.com>
Reviewed-By: Lorenzo Colitti <lorenzo@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210608044141.3898496-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller is required to enter D3hot rather than D3cold for AMD
s2idle on this hardware generation.
Otherwise, the 'Controller Not Ready' (CNR) bit is not being cleared by
host in resume and eventually this results in xhci resume failures during
the s2idle wakeup.
Link: https://lore.kernel.org/linux-usb/1612527609-7053-1-git-send-email-Prike.Liang@amd.com/
Suggested-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable <stable@vger.kernel.org> # 5.11+
Link: https://lore.kernel.org/r/20210527154534.8900-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reasoning for this change is that if we already had
a packet pending, then we also already had a pending timer,
and as such there is no need to reschedule it.
This also prevents packets getting delayed 60 ms worst case
under a tiny packet every 290us transmit load, by keeping the
timeout always relative to the first queued up packet.
(300us delay * 16KB max aggregation / 80 byte packet =~ 60 ms)
As such the first packet is now at most delayed by 300us.
Under low transmit load, this will simply result in us sending
a shorter aggregate, as originally intended.
This patch has the benefit of greatly reducing (by ~10 factor
with 1500 byte frames aggregated into 16 kiB) the number of
(potentially pretty costly) updates to the hrtimer.
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210608085438.813960-1-zenczykowski@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmC9dVwACgkQSFkpgVDW
cbs+oAf/b4mVmJpYIMTBM5tU086YpsZ80StjH3MVx2Hx/F8bM2ewovOUxOWPAY2o
A6ROuLUlU/0TT8U3LL5PEbQDHhuPsf1n3erv6iz63a72uzOouLeHOBYFP+E6aM5z
1mkr2yHXpwFe+aHpstXvOgeR4ano0kzMkx/I3SPH6P8/pXiBSrpvTiBwnxqvZxbb
VQuP9VfEF5e8vXuDiMF1V5qjea/BYnvjt2Yj34An3JHte13oTNRdFM/6aQiIEvt2
r6g0nBJizmhIHwtNYq30KfgFsNjiC9+dPtOCOVyv80c+Qu+F71EwEyqZSrOVLunh
hfxC/U6H8vy73Zo3gJP3xrXE+xvztw==
=OpDk
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Two bug fixes for cdns3 and cdnsp
* tag 'usb-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fix deadlock issue in cdnsp_thread_irq_handler
usb: cdns3: Enable TDL_CHK only for OUT ep
Here's a fix for some pipe-direction mismatches in the quatech2 driver,
and a couple of new device ids for ftdi_sio and omninet (and a related
trivial cleanup).
All but the ftdi_sio commit have been in linux-next, and with no
reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYLtSqwAKCRALxc3C7H1l
CPj2AQDSM/GeQ658vxYKPIA+8ZDBWubaYhq8KAUDqxL7hBMevAEAkbFhjgtyQt4h
32lqF2YsahxCHckvLXSnxxj1cTJxGAk=
=NKr6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Jonah writes:
USB-serial fixes for 5.13-rc5
Here's a fix for some pipe-direction mismatches in the quatech2 driver,
and a couple of new device ids for ftdi_sio and omninet (and a related
trivial cleanup).
All but the ftdi_sio commit have been in linux-next, and with no
reported issues.
* tag 'usb-serial-5.13-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add NovaTech OrionMX product ID
USB: serial: omninet: update driver description
USB: serial: omninet: add device id for Zyxel Omni 56K Plus
USB: serial: quatech2: fix control-request directions
Add PID for the NovaTech OrionMX so it can be automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds a udc_async_callbacks handler to the net2272 UDC
driver, which will prevent a theoretical race during gadget unbinding.
The net2272 driver is sufficiently complicated that I didn't want to
mess around with IRQ settings. Instead, the patch simply adds a new
flag to control async callbacks, and checks the flag before issuing
any of them.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202206.GF1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a udc_async_callbacks handler to the net2280 UDC
driver, which will prevent a theoretical race during gadget unbinding.
The net2280 driver is sufficiently complicated that I didn't want to
mess around with IRQ settings. Instead, the patch simply adds a new
flag to control async callbacks, and checks the flag before issuing
any of them.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202200.GE1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a udc_async_callbacks handler to the dummy-hcd UDC
driver, which will prevent a theoretical race during gadget unbinding.
The implementation is simple, since dummy-hcd already has a flag to
keep track of whether emulated IRQs are enabled. All the handler has
to do is store the enable value in the flag, and avoid setting the
flag prematurely.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202152.GD1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Gadget API has a theoretical race when a gadget driver is unbound.
Although the pull-up is turned off before the driver's ->unbind
callback runs, if the USB cable were to be unplugged at just the wrong
moment there would be nothing to prevent the UDC driver from invoking
the ->disconnect callback after the unbind has finished. In theory,
other asynchronous callbacks could also happen during the time before
the UDC driver's udc_stop routine is called, and the gadget driver
would not be prepared to handle any of them.
We need a way to tell UDC drivers to stop issuing asynchronous (that is,
->suspend, ->resume, ->disconnect, ->reset, or ->setup) callbacks at
some point after the pull-up has been turned off and before the
->unbind callback runs. This patch adds a new ->udc_async_callbacks
callback to the usb_gadget_ops structure for precisely this purpose,
and it adds the corresponding support to the UDC core.
Later patches in this series add support for udc_async_callbacks to
several UDC drivers.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202144.GC1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During unbind, ffs_func_eps_disable() will be executed, resulting in
completion callbacks for any pending USB requests. When using AIO,
irrespective of the completion status, io_data work is queued to
io_completion_wq to evaluate and handle the completed requests. Since
work runs asynchronously to the unbind() routine, there can be a
scenario where the work runs after the USB gadget has been fully
removed, resulting in accessing of a resource which has been already
freed. (i.e. usb_ep_free_request() accessing the USB ep structure)
Explicitly drain the io_completion_wq, instead of relying on the
destroy_workqueue() (in ffs_data_put()) to make sure no pending
completion work items are running.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621644261-1236-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
send discover identity hrtimer when unregister tcpm port.
Fixes: c34e85fa69 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-3-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the state_machine_timer, we should also cancel possible pending
frs hrtimer when unregister tcpm port.
Fixes: 8dc4bd0736 ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1622627829-11070-2-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving Alert Message, if it is not unexpected but is
unsupported for some reason, the port should return Not_Supported
Message response.
Also, according to PD3.0 Spec 6.5.2.1.4 Event Flags Field, the
OTP/OVP/OCP flags in the Event Flags field in Status Message no longer
require Get_PPS_Status Message to clear them. Thus remove it when
receiving Status Message with those flags being set.
In addition, add the missing AMS operations for Status Message.
Fixes: 64f7c494a3 ("typec: tcpm: Add support for sink PPS related messages")
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210531164928.2368606-1-kyletso@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When only PHY1 is used (for example on Odroid-HC4), the regmap init code
uses the usb2 ports when doesn't initialize the PHY1 regmap entry.
This fixes:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
pc : regmap_update_bits_base+0x40/0xa0
lr : dwc3_meson_g12a_usb2_init_phy+0x4c/0xf8
...
Call trace:
regmap_update_bits_base+0x40/0xa0
dwc3_meson_g12a_usb2_init_phy+0x4c/0xf8
dwc3_meson_g12a_usb2_init+0x7c/0xc8
dwc3_meson_g12a_usb_init+0x28/0x48
dwc3_meson_g12a_probe+0x298/0x540
platform_probe+0x70/0xe0
really_probe+0xf0/0x4d8
driver_probe_device+0xfc/0x168
...
Fixes: 013af227f5 ("usb: dwc3: meson-g12a: handle the phy and glue registers separately")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210601084830.260196-1-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
The remove function doesn't need to be fixed, because the
'regulator_disable()' call is already hidden in 'dwc3_meson_g12a_suspend()'
which is called via 'pm_runtime_set_suspended()' in the remove function.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/79df054046224bbb0716a8c5c2082650290eec86.1621616013.git.christophe.jaillet@wanadoo.fr
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_ams_start is used to initiate an AMS as well as checking Collision
Avoidance conditions but not for flagging passive AMS (initiated by the
port partner). Fix the misuses of tcpm_ams_start in tcpm_pd_svdm.
ATTENTION doesn't need responses so the AMS flag is not needed here.
Fixes: 0bc3ee9288 ("usb: typec: tcpm: Properly interrupt VDM AMS")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-5-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ID Header VDO and Product VDOs defined in USB PD Spec rev 2.0 and
rev 3.1 are quite different. Add an additional array snk_vdo_v1 and
send it as the response to the port partner if it only supports SVDM
version 1.0.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In USB PD Spec Rev 3.1 Ver 1.0, section "6.12.5 Applicability of
Structured VDM Commands", DFP is allowed and recommended to respond to
Discovery Identity with ACK. And in section "6.4.4.2.5.1 Commands other
than Attention", NAK should be returned only when receiving Messages
with invalid fields, Messages in wrong situation, or unrecognize
Messages.
Still keep the original design for SVDM Version 1.0 for backward
compatibilities.
Fixes: 193a68011f ("staging: typec: tcpm: Respond to Discover Identity commands")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210601123151.3441914-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel AlderLake(ADL) IOM has a different IOM port status offset than
Intel TigerLake.
Add a new ACPI ID for ADL and use the IOM port status offset as per
the platform.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Link: https://lore.kernel.org/r/20210601035843.71150-1-azhar.shaikh@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB charger type and status was already propagated to userspace
through kobject_uevent_env during charger notify work. Nevertheless the
uevent could be lost e.g. because it could be fired at an early kernel
boot stage, way before udev daemon or any other user-space app was able
to catch it. Registering uevent hook for introduced usb_phy_dev_type
will allow to query sysfs 'uevent' file to restore that information at
any time.
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Link: https://lore.kernel.org/r/20210531122222.453628-1-grzegorz.jaszczyk@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 92af4fc6ec ("usb: musb: Fix suspend with devices
connected for a64"), the logic to support the
MUSB_QUIRK_B_DISCONNECT_99 quirk was modified to only conditionally
schedule the musb->irq_work delayed work.
This commit badly breaks ECM Gadget on AM335X. Indeed, with this
commit, one can observe massive packet loss:
$ ping 192.168.0.100
...
15 packets transmitted, 3 received, 80% packet loss, time 14316ms
Reverting this commit brings back a properly functioning ECM
Gadget. An analysis of the commit seems to indicate that a mistake was
made: the previous code was not falling through into the
MUSB_QUIRK_B_INVALID_VBUS_91, but now it is, unless the condition is
taken.
Changing the logic to be as it was before the problematic commit *and*
only conditionally scheduling musb->irq_work resolves the regression:
$ ping 192.168.0.100
...
64 packets transmitted, 64 received, 0% packet loss, time 64475ms
Fixes: 92af4fc6ec ("usb: musb: Fix suspend with devices connected for a64")
Cc: stable@vger.kernel.org
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lore.kernel.org/r/20210528140446.278076-1-thomas.petazzoni@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There exists a possible scenario in which dwc3_gadget_init() can fail:
during during host -> peripheral mode switch in dwc3_set_mode(), and
a pending gadget driver fails to bind. Then, if the DRD undergoes
another mode switch from peripheral->host the resulting
dwc3_gadget_exit() will attempt to reference an invalid and dangling
dwc->gadget pointer as well as call dma_free_coherent() on unmapped
DMA pointers.
The exact scenario can be reproduced as follows:
- Start DWC3 in peripheral mode
- Configure ConfigFS gadget with FunctionFS instance (or use g_ffs)
- Run FunctionFS userspace application (open EPs, write descriptors, etc)
- Bind gadget driver to DWC3's UDC
- Switch DWC3 to host mode
=> dwc3_gadget_exit() is called. usb_del_gadget() will put the
ConfigFS driver instance on the gadget_driver_pending_list
- Stop FunctionFS application (closes the ep files)
- Switch DWC3 to peripheral mode
=> dwc3_gadget_init() fails as usb_add_gadget() calls
check_pending_gadget_drivers() and attempts to rebind the UDC
to the ConfigFS gadget but fails with -19 (-ENODEV) because the
FFS instance is not in FFS_ACTIVE state (userspace has not
re-opened and written the descriptors yet, i.e. desc_ready!=0).
- Switch DWC3 back to host mode
=> dwc3_gadget_exit() is called again, but this time dwc->gadget
is invalid.
Although it can be argued that userspace should take responsibility
for ensuring that the FunctionFS application be ready prior to
allowing the composite driver bind to the UDC, failure to do so
should not result in a panic from the kernel driver.
Fix this by setting dwc->gadget to NULL in the failure path of
dwc3_gadget_init() and add a check to dwc3_gadget_exit() to bail out
unless the gadget pointer is valid.
Fixes: e81a7018d9 ("usb: dwc3: allocate gadget structure dynamically")
Cc: <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210528160405.17550-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current sequence utilizes dwc3_gadget_disable_irq() alongside
synchronize_irq() to ensure that no further DWC3 events are generated.
However, the dwc3_gadget_disable_irq() API only disables device
specific events. Endpoint events can still be generated. Briefly
disable the interrupt line, so that the cleanup code can run to
prevent device and endpoint events. (i.e. __dwc3_gadget_stop() and
dwc3_stop_active_transfers() respectively)
Without doing so, it can lead to both the interrupt handler and the
pullup disable routine both writing to the GEVNTCOUNT register, which
will cause an incorrect count being read from future interrupts.
Fixes: ae7e86108b ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1621571037-1424-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the dentry pointer for a debugfs file that we
only use to remove it when the device goes away. debugfs can do the
lookup for us instead, saving us some trouble, and making things smaller
overall.
Cc: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20210527101426.3283214-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit acad3e9c72.
The device property that can be used to identify the device
class/type of the remote port parent when device graph is
used is always needed after all. Without it there is no real
way to know is the requested connection actually described
in the device graph or not.
If the connection is described in the device graph but the
device instance is still missing for what ever reason, the
code defers probe for now.
Adding a comment to the code to explain this.
Reviewed-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210602112253.70200-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the check for DRIVER_SENSE with a check for
scsi_status_is_check_condition().
Audit all callsites to ensure the SAM status is set correctly. For
backwards compability move the DRIVER_SENSE definition to sg.h, and update
sg, bsg, and scsi_ioctl to set the DRIVER_SENSE driver_status whenever
SAM_STAT_CHECK_CONDITION is present.
[mkp: fix zeroday srp warning]
Link: https://lore.kernel.org/r/20210427083046.31620-10-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix
A type of inconsistency that can show up in control URBs is when the
setup packet's wLength value does not match the URB's
transfer_buffer_length field. The two should always be equal;
differences could lead to information leaks or undefined behavior for
OUT transfers or overruns for IN transfers.
This patch adds a test for such mismatches during URB submission. If
the test fails, the submission is rejected with a -EBADR error code
(which is not used elsewhere in the USB core), and a debugging message
is logged for people interested in tracking down these errors.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210526153244.GA1400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/gadget/udc/udc-xilinx.c:802: warning: expecting prototype for xudc_ep_enable(). Prototype was for __xudc_ep_enable() instead
drivers/usb/gadget/udc/udc-xilinx.c:997: warning: expecting prototype for xudc_ep0_queue(). Prototype was for __xudc_ep0_queue() instead
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-20-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/typec/ucsi/ucsi.c:1287: warning: expecting prototype for ucsi_get_drvdata(). Prototype was for ucsi_set_drvdata() instead
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-25-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/isp1760/isp1760-udc.c:150: warning: Function parameter or member 'udc' not described in 'isp1760_udc_select_ep'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-7-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/common/ulpi.c:151: warning: expecting prototype for ulpi_register_driver(). Prototype was for __ulpi_register_driver() instead
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-4-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/cdns3/cdnsp-gadget.c:59: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-24-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/udc.c:247: warning: expecting prototype for hw_is_port_high_speed(). Prototype was for hw_port_is_high_speed() instead
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-17-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/otg.c:25: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/chipidea/otg.c:78: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/chipidea/otg.c:143: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-15-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/core.c:343: warning: expecting prototype for _ci_usb_phy_exit(). Prototype was for ci_usb_phy_exit() instead
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-14-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/cdns3/cdns3-ep0.c:680: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-ep0.c:775: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-ep0.c:868: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Aswath Govindraju <a-govindraju@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Pawel Jez <pjez@cadence.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-10-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/cdns3/cdns3-gadget.c:163: warning: expecting prototype for select_ep(). Prototype was for cdns3_select_ep() instead
drivers/usb/cdns3/cdns3-gadget.c:2025: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2224: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2247: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2264: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2399: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2489: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2589: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2656: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2677: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2722: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2768: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2877: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2923: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/usb/cdns3/cdns3-gadget.c:2986: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Aswath Govindraju <a-govindraju@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Pawel Jez <pjez@cadence.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-8-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/cdns3/core.c:342: warning: expecting prototype for cdsn3_role_get(). Prototype was for cdns_role_get() instead
drivers/usb/cdns3/core.c:428: warning: expecting prototype for cdns_probe(). Prototype was for cdns_init() instead
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Aswath Govindraju <a-govindraju@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the "removable" attribute from USB to core in order to allow it to be
supported by other subsystem / buses. Individual buses that want to support
this attribute can populate the removable property of the device while
enumerating it with the 3 possible values -
- "unknown"
- "fixed"
- "removable"
Leaving the field unchanged (i.e. "not supported") would mean that the
attribute would not show up in sysfs for that device. The UAPI (location,
symantics etc) for the attribute remains unchanged.
Move the "removable" attribute from USB to the device core so it can be
used by other subsystems / buses.
By default, devices do not have a "removable" attribute in sysfs.
If a subsystem or bus driver wants to support a "removable" attribute, it
should call device_set_removable() before calling device_register() or
device_add(), e.g.:
device_set_removable(dev, DEVICE_REMOVABLE);
device_register(dev);
The possible values and the resulting sysfs attribute contents are:
DEVICE_REMOVABLE_UNKNOWN -> "unknown"
DEVICE_REMOVABLE -> "removable"
DEVICE_FIXED -> "fixed"
Convert the USB "removable" attribute to use this new device core
functionality. There should be no user-visible change in the location or
semantics of attribute for USB devices.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-1-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the dentry pointer for a debugfs file that we
only use to remove it when the device goes away. debugfs can do the
lookup for us instead, saving us some trouble, and making things smaller
overall.
Link: https://lore.kernel.org/r/20210525172534.848775-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the dentry pointer for a debugfs file that we
only use to remove it when the device goes away. debugfs can do the
lookup for us instead, saving us some trouble, and making things smaller
overall.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20210525171636.758758-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the dentry pointer for a debugfs file that we
only use to remove it when the device goes away. debugfs can do the
lookup for us instead, saving us some trouble, and making things smaller
overall.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: bcm-kernel-feedback-list@broadcom.com
Link: https://lore.kernel.org/r/20210525171508.758365-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the dentry pointer for a debugfs file that we
only use to remove it when the device goes away. debugfs can do the
lookup for us instead, saving us some trouble, and making things smaller
overall.
Cc: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20210525171419.758146-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0bd0f6d201 ("usb: dwc3: gadget: remove allocated/queued request
tracking") removed the allocated & queued fields from struct dwc3_ep
but neglected to also remove them from the dwc3_log_trb event class's
TP_STRUCT definition which are now unused. Remove them to save eight
bytes per trace event entry.
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210527012924.3596-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The additional boolean device property "orientation-switch"
is not needed when the connection is described with device
graph, so removing the check and the requirement for it.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210526153548.61276-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the USB Type-C switch and mux have already a device
type defined for them. We can use those types instead of the
device name to differentiate the two.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210526153548.61276-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduces usb_role_string() function, which returns a
human-readable name of provided usb role, it's useful to
make the log readable.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1621932786-9335-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If endpoints halts due to a stall then the dequeue pointer read from
hardware may already be set ahead of the stalled TRB.
After commit 674f8438c1 ("xhci: split handling halted endpoints into two
steps") in 5.12 xhci driver won't issue a Set TR Dequeue if hardware
dequeue pointer is already in the right place.
Turns out the "Set TR Dequeue pointer" command is anyway needed as it in
addition to moving the dequeue pointer also clears endpoint state and
cache.
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: <stable@vger.kernel.org> # 5.12
Reported-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Tested-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210525074100.1154090-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
5.12 kernel changes how xhci handles cancelled URBs and halted
endpoints. Among these changes cancelled and stalled URBs are no longer
given back before they are cleared from xHC hardware cache.
These changes unfortunately cleared the -EPIPE status of a stalled
transfer in one case before giving bak the URB, causing a USB card reader
to fail from working.
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: <stable@vger.kernel.org> # 5.12
Reported-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Tested-by: Peter Ganzhorn <peter.ganzhorn@googlemail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210525074100.1154090-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the inclusion of Omni 56K Plus, this driver seem to be more common
among the family of Zyxel omni modem. Update the driver and module
descriptions.
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for Zyxel Omni 56K Plus modem, this modem include:
USB chip:
NetChip
NET2888
Main chip:
901041A
F721501APGF
Another modem using the same chips is the Zyxel Omni 56K DUO/NEO,
could be added with the right USB ID.
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the three requests which erroneously used usb_rcvctrlpipe().
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
ZLP gets stuck if TDL_CHK bit is set and TDL_FROM_TRB is used
as TDL source for IN endpoints. To fix it, TDL_CHK is only
enabled for OUT endpoints.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Link: https://lore.kernel.org/r/1621263912-13175-1-git-send-email-sparmar@cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The sparse tool complains as follows:
drivers/usb/typec/tcpm/tcpci.c:118:5: warning:
symbol 'tcpci_apply_rc' was not declared. Should it be static?
This symbol is not used outside of tcpci.c, so marks it static.
Fixes: 7257fbc7c5 ("usb: typec: tcpci: Implement callback for apply_rc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210524133704.2432555-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is using open-coded variant of of_find_i2c_device_by_node().
Replace it by the actual call to the above mentioned API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210521145243.87911-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_sndctrlpipe() is evaluated in do_proc_control(), saved in a
variable, then evaluated again. Use the saved variable instead, to
match the use of usb_rcvctrlpipe().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210521174027.GA116484@m.b4.vu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/gadget/udc/trace files follows this syntax, but
the content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc.
For e.g., running scripts/kernel-doc -none drivers/usb/gadget/udc/trace.h
emits:
warning: expecting prototype for udc.c(). Prototype was for TRACE_SYSTEM() instead
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210522115227.9977-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb3_start_pipen() is called by renesas_usb3_ep_queue() and
usb3_request_done_pipen() so that usb3_start_pipen() is possible
to cause a race when getting usb3_first_req like below:
renesas_usb3_ep_queue()
spin_lock_irqsave()
list_add_tail()
spin_unlock_irqrestore()
usb3_start_pipen()
usb3_first_req = usb3_get_request() --- [1]
--- interrupt ---
usb3_irq_dma_int()
usb3_request_done_pipen()
usb3_get_request()
usb3_start_pipen()
usb3_first_req = usb3_get_request()
...
(the req is possible to be finished in the interrupt)
The usb3_first_req [1] above may have been finished after the interrupt
ended so that this driver caused to start a transfer wrongly. To fix this
issue, getting/checking the usb3_first_req are under spin_lock_irqsave()
in the same section.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210524060155.1178724-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If snk_vdo is not populated from fwnode, it implies the port does not
support responding to SVDM commands. Not_Supported Message shall be sent
if the contract is in PD3. And for PD2, the port shall ignore the
commands.
Fixes: 193a68011f ("staging: typec: tcpm: Respond to Discover Identity commands")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210523015855.1785484-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a VDM AMS is interrupted by Messages other than VDM, the AMS needs
to be finished properly. Also start a VDM AMS if receiving SVDM Commands
from the port partner to complement the functionality of tcpm_vdm_ams().
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210523015855.1785484-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmCo29gACgkQSFkpgVDW
cbtPrwf/ddqvOp96mZ0PUjCSibVm/9KpB3IxMVv8DAAYnMnHm+KBXrSjK2Zg9bm/
OegHdP0NQLghb42pesiBDoGEkmiQ8siF6LGjifT9posUu2ZJBQJDcHPdl1aIZh+j
D2i4DQLqlw3rNFktpubuUJq7ZIAacF9Henbr1zt7Ns9fPrnzt6dT/dH+YuFe6uXT
g/ZXpa4ari/ctqqKeglplMQDL6h3a0QCxTsoU0UVC76/cw1UCOOMcr8QEUH5kngK
bxVH0yAr51Hz1oUMQBWQS2nMzAy023X9CXgSymGGksHMs7rL1TfKis/i1wnqaFzH
V0YHSWIHZlGAyLvSl8Mivr9MUTNaAw==
=LBnr
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Some small bug fixes for both chipidea and cdns USB
* tag 'usb-v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: udc: assign interrupt number to USB gadget structure
usb: cdnsp: Fix lack of removing request from pending list.
usb: cdns3: Fix runtime PM imbalance on error
When a control URB is submitted, the direction indicated by URB's pipe
member is supposed to match the direction indicated by the setup
packet's bRequestType member. A mismatch could lead to trouble,
depending on which field the host controller drivers use for
determining the actual direction.
This shouldn't ever happen; it would represent a careless bug in a
kernel driver somewhere. This patch adds a dev_WARN_ONCE to let
people know about the potential problem.
Suggested-by: "Geoffrey D. Bennett" <g@b4.vu>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210522021623.GB1260282@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the set-speed request which erroneously used USB_DIR_IN and update
the default timeout argument to match (same value).
Fixes: 5638e4d92e ("USB: add PlayStation 2 Trance Vibrator driver")
Cc: stable@vger.kernel.org # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133109.17396-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids for various drivers.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYKe8NgAKCRALxc3C7H1l
CFGYAP9v0yxAMEfk13arbCe0rX4ADkVQWf1SfJen1O7Dk12Z4wD5AQ8vslptBywY
aflwx2tep6oclJ56D+WmKz/P058mOAA=
=LFmI
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.13-rc3
Here are some new device ids for various drivers.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.13-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add device id for ADLINK ND-6530 GC
USB: serial: ti_usb_3410_5052: add startech.com device id
USB: serial: option: add Telit LE910-S1 compositions 0x7010, 0x7011
USB: serial: ftdi_sio: add IDs for IDS GmbH Products
APPLY RC is defined as ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. When ROLE_CONTROL.CC1 ==
ROLE_CONTROL.CC2, set the other CC to OPEN.
Fixes: f321a02cae ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When vbus auto discharge is enabled, TCPCI based TCPC transitions
into Attached.SNK/Attached.SRC state. During PR_SWAP, TCPCI based
TCPC would disconnect when partner changes power roles. TCPC has
to be moved APPLY RC state during PR_SWAP. This is done by
ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. Once the swap sequence
is done, AutoDischargeDisconnect is re-enabled.
Fixes: f321a02cae ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logic to enable vbus auto discharge on disconnect is used in
more than one place. Since this is repetitive code, moving this into
its own method.
Fixes: f321a02cae ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During PR_SWAP, When TCPM is in PR_SWAP_SNK_SRC_SINK_OFF, vbus is
expected to reach VSAFE0V when source turns off vbus. Do not move
to SNK_UNATTACHED state when this happens.
Fixes: 28b43d3d74 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from drivers that got this wrong.
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210519093303.10789-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
While at it drop two redundant return-value initialisations from two of
the functions that got it wrong.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210519093303.10789-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210519093303.10789-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than testing if the error code is -EPROBE_DEFER before printing
an error message, use dev_err_probe() instead to simplify the code.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210519163553.212682-2-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra XUDC driver prints the following error when deferring probe
if the USB PHY is not found ...
ERR KERN tegra-xudc 3550000.usb: failed to get usbphy-0: -517
Deferring probe can be normal and so update to driver to avoid printing
this error if probe is being deferred.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210519163553.212682-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides the already host mode support add peripheral mode support for
the isp1763 IP from the isp1760 family.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-10-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1763 have some differences from the isp1760, 8 bit address for
registers and 16 bit for values, no bulk access to memory addresses,
16 PTD's instead of 32.
Following the regmap work done before add the registers, memory access
and add the functions to support differences in setup sequences.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-8-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is already a binding to describe the dual role mode (dr_mode),
use that instead of defining a new one (port1-otg).
Update driver code and devicetree files that use that port1-otg
binding.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-7-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to support other family member IP, which may have
different memory layout. Drop macros and setup a configuration
struct.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-6-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the removal of the Blackfin port with:
commit 4ba66a9760 ("arch: remove blackfin port")
No one is using or referencing this header and platform data struct.
Remove them.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-5-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use io relaxed access memory primitives to satisfy strict type
checking (__force).
This will fix some existing sparse warnings:
sparse: warning: cast to restricted __le32
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-4-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework access to registers and memory to use regmap framework.
No change in current feature or way of work is intended with this
change.
This will allow to reuse this driver with other IP of this family,
for example isp1763, with little changes and effort.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-3-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a lot of pre-existing typechecking warnings around the
access and assign of elements of ptd structure of __dw type.
sparse: warning: invalid assignment: |=
sparse: left side has type restricted __dw
sparse: right side has type unsigned int
or
warning: restricted __dw degrades to integer
or
sparse: warning: incorrect type in assignment (different base types)
sparse: expected restricted __dw [usertype] dw4
sparse: got unsigned int [assigned] [usertype] usof
To handle this, annotate conversions along the {TO,FROM}_DW* macros
and some assignments and function arguments.
This clean up completely all sparse warnings for this driver.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-2-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from the three drivers that got this
wrong.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were called with a NULL port
driver-data pointer or if some other always-true sanity checks failed.
The bogus sanity checks were later removed by commit ce039bd4b2 ("USB:
serial: mos7840: drop paranoid port checks") and 7b2faede67 ("USB:
serial: mos7840: drop port driver data accessors") but the
function-header comments were never updated to match.
Drop the outdated return-value comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were ever called with a NULL port
driver-data pointer. The return value was later changed to zero by
commit 23198fda71 ("tty: fix chars_in_buffers") but the bogus sanity
checks were left in place as were the outdated function-header comments.
The port driver data isn't cleared until after the port has been
deregistered and all open ttys have been hung up so drop the unnecessary
sanity checks and the outdated comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were called while or after the port
had been closed. The return value was later changed to zero by commit
d76f2f4462 ("io_edgeport: Fix various bogus returns to the tty
layer") but the bogus sanity checks were left in place as were the
outdated function-header comments.
These callbacks will never be called for an uninitialised port so drop
the unnecessary sanity checks and the outdated comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Both the dp_write_urb_in_use flag and dp_out_buf_len counter should be
accessed while holding the driver port lock. Add the missing locking to
chars_in_buffer and clean up the implementation somewhat by using a
common exit path.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Due to an ancient quirk in n_tty poll implementation, the
digi_acceleport driver has been reporting that its queue contains 256
(WAKEUP_CHARS) characters whenever its write URB is in use.
This has not been necessary since 2003 when the line-discipline started
taking the write room into account so let's return the maximum transfer
size again in order to over-report a little less and incidentally fix
the related debug statement.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Sergey Shtylyov