[ Upstream commit c4d57c22ac ]
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for new device: the TI bq34z100-G1, a Wide Range Fuel Gauge
for Li-Ion, PbA, NiMH, and NiCd batteries. The device shares a lot with
other models, although it has its own differences requiring new quirks.
This patch was tested on a system equipped with NiMH batteries.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In commit 830ae44220 ("extcon: Remove the deprecated extcon functions")
the function extcon_register_interest became a no-op returning an error,
leading to non-functional behaviour in charger-manager.
Additionally, a translation table is needed between the text representation
of the extcon cable names and their IDs is needed. In order to retain DT
compatibility, TA and CHARGE-DOWNSTREAM are added as they were present up
until commit 11eecf910b ("extcon: Modify the id and name of external
connector")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
cm_monitor(), where charging management starts, checks various charging
condition sequentially to decide next charging operation. However, as it
follows sequential process, cascaded if statements, it does some
jobs which have already done in the previous stage. This results in a
delay in decision making. Moreover, starting point of charging is spread
all around which makes maintain code and debugging difficult.
Both of the problems mentioned above become clean if it manages battery
charging focusing on battery status not following sequential condition
checking. Now, cm_monitor() moves battery state diagram and does the
optimal operation for current state. As a result, it reduces whole
monitoring time almost in half.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
cm_notify_event() was introduced to get an event associated with the
battery status externally (ie in board files), but no one ever used it.
Moreover it makes charger manager driver more complicated. Drop the
function and all data related to it to simplify the driver.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are no platforms using the pdata support, so let's
drop it to simplify the driver.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This converts the GPIO charger to use exclusively GPIO
descriptors, moving the two remaining platforms passing
global GPIO numbers over to using a GPIO descriptor table.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the Texas Instruments BQ28z610 battery monitor.
The register address map is laid out the same as compared to other
devices within the file.
The battery status register bits are similar to the bq27z561 but they
are different compared to other fuel gauge devices within this file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the Texas Instruments BQ27Z561 battery monitor. The register address
map is laid out the same as compared to other devices within the file.
The battery status register has differing bits to determine if the
battery is full, discharging or dead.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the doubled word "for".
Change "It it" to "If it".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-pm@vger.kernel.org
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
For security reasons I stopped using gmail account and kernel address is
now up-to-date alias to my personal address.
People periodically send me emails to address which they found in source
code of drivers, so this change reflects state where people can contact
me.
[ Added .mailmap entry as per Joe Perches - Linus ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200307104237.8199-1-pali@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow charger manager can be built as a module like other charger
drivers.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The MAX17055 is very similar to the MAX17042 so extend the driver.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The omap_sr_pdata is not declared but is exported, so add a
define for it to fix the following warning:
arch/arm/mach-omap2/pdata-quirks.c:609:36: warning: symbol 'omap_sr_pdata' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 37 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.724130665@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This migrates isp1704 driver from old GPIO API to new descriptor
based GPIO API and drops useless platform data as a side-effect.
Migration is simple, since all mainline users are DT based and
DT API does not change. Out of tree users of the platform data
need to migrate to gpiod_lookup_table as described here:
Documentation/driver-api/gpio/board.rst
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
* New core support
- battery internal resistance
- battery OCV capacity lookup table
- support for custom sysfs attributes
* Convert all drivers to use power-supply core support for custom sysfs attributes
* bq24190-charger: bq24196 support
* axp20x-charger: AXP813 support
* sc27xx-battery: new fuel gauge driver
* gpio-poweroff: support for specific active and inactive delays
* Misc fixes
-----BEGIN PGP SIGNATURE-----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=59iw
-----END PGP SIGNATURE-----
Merge tag 'for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- New core support:
- battery internal resistance
- battery OCV capacity lookup table
- support for custom sysfs attributes
- Convert all drivers to use power-supply core support for custom sysfs
attributes
- bq24190-charger: bq24196 support
- axp20x-charger: AXP813 support
- sc27xx-battery: new fuel gauge driver
- gpio-poweroff: support for specific active and inactive delays
- Misc fixes
* tag 'for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (53 commits)
power: supply: bq25890: fix BAT_COMP field definition
power: supply: gpio-charger: Do not use deprecated POWER_SUPPLY_TYPE_USB_*
power: supply: ds2781: switch to devm_power_supply_register
power: supply: ds2780: switch to devm_power_supply_register
power: supply: ds2781: fix race-condition in bin attribute registration
power: supply: ds2780: fix race-condition in bin attribute registration
power: supply: pcf50633: fix race-condition in sysfs registration
power: supply: charger-manager: fix race-condition in sysfs registration
power: supply: charger-manager: simplify generation of sysfs attribute group name
power: supply: bq24257: fix race-condition in sysfs registration
power: supply: bq24190_charger: fix race-condition in sysfs registration
power: supply: lp8788: fix race-condition in sysfs registration
power: supply: ds2781: fix race-condition in sysfs registration
power: supply: ds2780: fix race-condition in sysfs registration
power: supply: bq2415x: fix race-condition in sysfs registration
power: supply: core: add support for custom sysfs attributes
power: supply: sc27xx: Save last battery capacity
power: reset: at91-poweroff: move shdwc related data to one structure
power: supply: sc27xx: Add suspend/resume interfaces
power: supply: sc27xx: Add fuel gauge low voltage alarm
...
This registers custom sysfs properties using the native functionality
of the power-supply framework, which cleans up the code a bit and
fixes a race-condition. Before this patch the sysfs attributes were
not properly registered to udev.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix up licensing to be inline with Linux conventions.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
omap_sr_register_pmic() was introduced in 2010 in commit
984aa6dbf4 ("OMAP3: PM: Adding smartreflex driver support.")
. There was never any caller of this function in mainline resulting in a
warning
sr_init: No PMIC hook to init smartreflex
for each machine where this driver is enabled. So remove the unused
function and the pr_warn.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to the datasheet, bq27411 is similar to bq27421.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This device is software similar to the BQ27426 except it has
different data memory offsets. Add support here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We are still initializing smartreflex with platform data using
omap_device_build(). We can instead pass the platform data in
with auxdata in pdata-quirks.c and make the driver use that
in later patches.
Note that we cannot enable the auxdata use yet, this is done
in the last patch of the series.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds basic support for BQ27521 battery monitor, used in Nokia N9
and N950. In particular, battery voltage is important to be able to
tell when the battery is almost empty. Emptying battery on N950 is
pretty painful, as flasher needs to be used to recover phone in such case.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register the 5V boost converter as a regulator named "usb_otg_vbus".
This commit also adds support for bq24190_platform_data, through which
non device-tree platforms can pass the regulator_init_data (containing
mappings for the consumer amongst other things).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Support data memory update on BQ27425. Parameters from TI datasheets are also
provided for BQ27500, 545, 421, 441, 621; however these are commented out,
as they are not tested.
Add BQ27XXX_O_CFGUP & _O_RAM for use in bq27xxx_chip_data[n].opts
and by data memory update functions.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
For the existing features, these chips act like others already ID'd,
so they had false but functional IDs. We will be adding features
which require correct IDs, so the following IDs are added:
BQ2752X, 531, 542, 546, 742, 425, 441, 621
Chip-specific features are now tracked by BQ27XXX_O_* flags in di->opts.
No functional changes to the driver.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When the BQ27xxx driver was originally written the w1 subsystem only
allowed device drivers for w1 attached devices to live in the w1
subsystem. Kernel driver subsystems expect that the driver for a device
live in the directory of the subsystem for which it implements
functionality, not in the directory of the bus that it is attached. To
work around this, the BQ27xxx driver was implemented as a platform device
driver and the interface driver would instantiate this device from within
the w1 directory, then pass a w1 read callback as platform data.
As we can now have the w1 interface driver in the power/supply directory
(like we do already with the i2c interface driver) we can remove this
middle-layer platform driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Previously there was no way to configure these chips in the event that the
defaults didn't match the battery in question.
For chips with RAM data memory (and also those with flash/NVM data memory
if CONFIG_BATTERY_BQ27XXX_DT_UPDATES_NVM is defined and the user has not
set module param dt_monitored_battery_updates_nvm=0) we now call
power_supply_get_battery_info(), check its values, and write battery
properties to chip data memory if there is a dm_regs table for the chip.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add these to enable read/write of chip data memory RAM/NVM/flash:
bq27xxx_battery_seal()
bq27xxx_battery_unseal()
bq27xxx_battery_set_cfgupdate()
bq27xxx_battery_soft_reset()
bq27xxx_battery_read_dm_block()
bq27xxx_battery_write_dm_block()
bq27xxx_battery_checksum_dm_block()
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Declare bus.write/read_bulk/write_bulk().
Add I2C write/read_bulk/write_bulk() to implement the above.
Add bq27xxx_write/read_block/write_block() helpers to call the above.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: "Andrew F. Davis" <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Userspace prefers the driver having a status property over having to guess
itself. Specifically this will properly make the GNOME3 UI (and likely
others) properly show discharging / charging / full status, instead
of always showing discharging as status.
Note that in the case there is no charger driver supplying the max17042,
then a status of unknown will get returned. At least upower treats
this the same as not having a status attribute, so in this case nothing
changes from a userspace pov.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some x86 machines use a max17047 fuel-gauge and x86 might be missing
platform_data if not provided by SFI.
This commit adds default platform_data as fallback option so that the
driver can work on boards where no platform_data is provided.
Since not all boards have a thermistor hooked up, set temp_min to 0 and
change the health checks from temp <= temp_min to temp < temp_min to
not trigger on such boards (where temp reads 0).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The i2c-core already maps of irqs before calling the driver's probe
function and there are no in tree users of
bq24190_platform_data->gpio_int.
Remove the redundant custom irq-mapping code and just use client->irq.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G4 chip definition to specifically match the
bq27520-G4 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G3 chip definition to specifically match the
bq27520-G3 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G2 chip definition to specifically match the
bq27520-G2 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G1 chip definition to specifically match the
bq27520-G1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G3 chip definition to specifically match the
bq27510-G3 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Tested-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G2 chip definition to specifically match the
bq27510-G2 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G1 chip definition to specifically match the
bq27510-G1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27500 chip definition to specifically match the
bq27500/1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The BQ2751X definition exists only to satisfy backwards compatibility.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>