commit 0d5e2a8223 upstream
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dbe5f1936 upstream
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f9634762 ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85cf67a33 upstream
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d2 ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 696450c051 upstream
Clear the RGMII_LINK bit upon detecting link down to be consistent with
setting the bit upon link up. We also move the clearing of the
out-of-band disable to the runtime initialization rather than for each
link up/down transition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221118213754.1383364-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cf3506587 upstream.
If kobject_add() is fail in bind_rdev_to_array(), 'rdev->serial' will be
alloc not be freed, and kmemleak occurs.
unreferenced object 0xffff88815a350000 (size 49152):
comm "mdadm", pid 789, jiffies 4294716910
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc f773277a):
[<0000000058b0a453>] kmemleak_alloc+0x61/0xe0
[<00000000366adf14>] __kmalloc_large_node+0x15e/0x270
[<000000002e82961b>] __kmalloc_node.cold+0x11/0x7f
[<00000000f206d60a>] kvmalloc_node+0x74/0x150
[<0000000034bf3363>] rdev_init_serial+0x67/0x170
[<0000000010e08fe9>] mddev_create_serial_pool+0x62/0x220
[<00000000c3837bf0>] bind_rdev_to_array+0x2af/0x630
[<0000000073c28560>] md_add_new_disk+0x400/0x9f0
[<00000000770e30ff>] md_ioctl+0x15bf/0x1c10
[<000000006cfab718>] blkdev_ioctl+0x191/0x3f0
[<0000000085086a11>] vfs_ioctl+0x22/0x60
[<0000000018b656fe>] __x64_sys_ioctl+0xba/0xe0
[<00000000e54e675e>] do_syscall_64+0x71/0x150
[<000000008b0ad622>] entry_SYSCALL_64_after_hwframe+0x6c/0x74
Fixes: 963c555e75 ("md: introduce mddev_create/destroy_wb_pool for the change of member device")
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240208085556.2412922-1-linan666@huaweicloud.com
[ mddev_destroy_serial_pool third parameter was removed in mainline,
where there is no need to suspend within this function anymore. ]
Signed-off-by: Jeremy Bongio <jbongio@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07a57a338a upstream.
Tony reported that the Machine check recovery was broken in v6.9-rc1, as
he was hitting a VM_BUG_ON when injecting uncorrectable memory errors to
DRAM.
After some more digging and debugging on his side, he realized that this
went back to v6.1, with the introduction of 'commit 0d206b5d2e
("mm/swap: add swp_offset_pfn() to fetch PFN from swap entry")'. That
commit, among other things, introduced swp_offset_pfn(), replacing
hwpoison_entry_to_pfn() in its favour.
The patch also introduced a VM_BUG_ON() check for is_pfn_swap_entry(), but
is_pfn_swap_entry() never got updated to cover hwpoison entries, which
means that we would hit the VM_BUG_ON whenever we would call
swp_offset_pfn() for such entries on environments with CONFIG_DEBUG_VM
set. Fix this by updating the check to cover hwpoison entries as well,
and update the comment while we are it.
Link: https://lkml.kernel.org/r/20240407130537.16977-1-osalvador@suse.de
Fixes: 0d206b5d2e ("mm/swap: add swp_offset_pfn() to fetch PFN from swap entry")
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Reported-by: Tony Luck <tony.luck@intel.com>
Closes: https://lore.kernel.org/all/Zg8kLSl2yAlA3o5D@agluck-desk3/
Tested-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: <stable@vger.kernel.org> [6.1.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1db7959aac upstream.
[BUG]
There is a recent report that when memory pressure is high (including
cached pages), btrfs can spend most of its time on memory allocation in
btrfs_alloc_page_array() for compressed read/write.
[CAUSE]
For btrfs_alloc_page_array() we always go alloc_pages_bulk_array(), and
even if the bulk allocation failed (fell back to single page
allocation) we still retry but with extra memalloc_retry_wait().
If the bulk alloc only returned one page a time, we would spend a lot of
time on the retry wait.
The behavior was introduced in commit 395cb57e85 ("btrfs: wait between
incomplete batch memory allocations").
[FIX]
Although the commit mentioned that other filesystems do the wait, it's
not the case at least nowadays.
All the mainlined filesystems only call memalloc_retry_wait() if they
failed to allocate any page (not only for bulk allocation).
If there is any progress, they won't call memalloc_retry_wait() at all.
For example, xfs_buf_alloc_pages() would only call memalloc_retry_wait()
if there is no allocation progress at all, and the call is not for
metadata readahead.
So I don't believe we should call memalloc_retry_wait() unconditionally
for short allocation.
Call memalloc_retry_wait() if it fails to allocate any page for tree
block allocation (which goes with __GFP_NOFAIL and may not need the
special handling anyway), and reduce the latency for
btrfs_alloc_page_array().
Reported-by: Julian Taylor <julian.taylor@1und1.de>
Tested-by: Julian Taylor <julian.taylor@1und1.de>
Link: https://lore.kernel.org/all/8966c095-cbe7-4d22-9784-a647d1bf27c3@1und1.de/
Fixes: 395cb57e85 ("btrfs: wait between incomplete batch memory allocations")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9da27fb65a upstream.
The expiry time of a key is unconditionally overwritten during
instantiation, defaulting to turn it permanent. This causes a problem
for DNS resolution as the expiration set by user-space is overwritten to
TIME64_MAX, disabling further DNS updates. Fix this by restoring the
condition that key_set_expiry is only called when the pre-parser sets a
specific expiry.
Fixes: 39299bdd25 ("keys, dns: Allow key types (eg. DNS) to be reclaimed immediately on expiry")
Signed-off-by: Silvio Gissi <sifonsec@amazon.com>
cc: David Howells <dhowells@redhat.com>
cc: Hazem Mohamed Abuelfotoh <abuehaze@amazon.com>
cc: linux-afs@lists.infradead.org
cc: linux-cifs@vger.kernel.org
cc: keyrings@vger.kernel.org
cc: netdev@vger.kernel.org
cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6827738dc6 upstream.
After the patch to restrict the use of mmap() to CAP_SYS_RAWIO for
the currently existing devices, most applications can no longer make
use of the accelerators as in production "you don't run things as root".
To keep the DSA and IAA accelerators usable, hook up a write() method
so that applications can still submit work. In the write method,
sufficient input validation is performed to avoid the security issue
that required the mmap CAP_SYS_RAWIO check.
One complication is that the DSA device allows for indirect ("batched")
descriptors. There is no reasonable way to do the input validation
on these indirect descriptors so the write() method will not allow these
to be submitted to the hardware on affected hardware, and the sysfs
enumeration of support for the opcode is also removed.
Early performance data shows that the performance delta for most common
cases is within the noise.
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e11452eb07 upstream.
On Sapphire Rapids and related platforms, the DSA and IAA devices have an
erratum that causes direct access (for example, by using the ENQCMD or
MOVDIR64 instructions) from untrusted applications to be a security problem.
To solve this, add a flag to the PCI device enumeration and device structures
to indicate the presence/absence of this security exposure. In the mmap()
method of the device, this flag is then used to enforce that the user
has the CAP_SYS_RAWIO capability.
In a future patch, a write() based method will be added that allows untrusted
applications submit work to the accelerator, where the kernel can do
sanity checking on the user input to ensure secure operation of the accelerator.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95feb3160e upstream.
Due to an erratum with the SPR_DSA and SPR_IAX devices, it is not secure to assign
these devices to virtual machines. Add the PCI IDs of these devices to the VFIO
denylist to ensure that this is handled appropriately by the VFIO subsystem.
The SPR_DSA and SPR_IAX devices are on-SOC devices for the Sapphire Rapids
(and related) family of products that perform data movement and compression.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40d442f969 upstream.
A recent commit fixed the code that parses the firmware files before
downloading them to the controller but introduced a memory leak in case
the sanity checks ever fail.
Make sure to free the firmware buffer before returning on errors.
Fixes: f905ae0be4b7 ("Bluetooth: qca: add missing firmware sanity checks")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda0d6a198 upstream.
Add the missing sanity checks and move the 255-byte build-id buffer off
the stack to avoid leaking stack data through debugfs in case the
build-info reply is malformed.
Fixes: c0187b0bd3 ("Bluetooth: btqca: Add support to read FW build version for WCN3991 BTSoC")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0adcf6be14 upstream.
Add the missing sanity check when fetching the board id to avoid leaking
slab data when later requesting the firmware.
Fixes: a7f8dedb4b ("Bluetooth: qca: add support for QCA2066")
Cc: stable@vger.kernel.org # 6.7
Cc: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a112d3c72a upstream.
The NVM configuration files used by WCN3988 and WCN3990/1/8 have two
sets of configuration tags that are enclosed by a type-length header of
type four which the current parser fails to account for.
Instead the driver happily parses random data as if it were valid tags,
something which can lead to the configuration data being corrupted if it
ever encounters the words 0x0011 or 0x001b.
As is clear from commit b63882549b ("Bluetooth: btqca: Fix the NVM
baudrate tag offcet for wcn3991") the intention has always been to
process the configuration data also for WCN3991 and WCN3998 which
encodes the baud rate at a different offset.
Fix the parser so that it can handle the WCN3xxx configuration files,
which has an enclosing type-length header of type four and two sets of
TLV tags enclosed by a type-length header of type two and three,
respectively.
Note that only the first set, which contains the tags the driver is
currently looking for, will be parsed for now.
With the parser fixed, the software in-band sleep bit will now be set
for WCN3991 and WCN3998 (as it is for later controllers) and the default
baud rate 3200000 may be updated by the driver also for WCN3xxx
controllers.
Notably the deep-sleep feature bit is already set by default in all
configuration files in linux-firmware.
Fixes: 4219d46868 ("Bluetooth: btqca: Add wcn3990 firmware download support.")
Cc: stable@vger.kernel.org # 4.19
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4edfa1e2 upstream.
Add the missing sanity checks when parsing the firmware files before
downloading them to avoid accessing and corrupting memory beyond the
vmalloced buffer.
Fixes: 83e81961ff ("Bluetooth: btqca: Introduce generic QCA ROME support")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 691aae4f36 upstream.
This patch fix xfstests generic/070 test with smb2 leases = yes.
cifs.ko doesn't set parent lease key and epoch in create context v2 lease.
ksmbd suppose that parent lease and epoch are vaild if data length is
v2 lease context size and handle directory lease using this values.
ksmbd should hanle it as v1 lease not v2 lease if parent lease key and
epoch are not set in create context v2 lease.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97c2ec6466 upstream.
This patch fixes generic/011 when enable smb2 leases.
if ksmbd sends multiple notifications for a file, cifs increments
the reference count of the file but it does not decrement the count by
the failure of queue_work.
So even if the file is closed, cifs does not send a SMB2_CLOSE request.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc00bc83f2 upstream.
ΕΛΕΝΗ reported that ksmbd binds to the IPV6 wildcard (::) by default for
ipv4 and ipv6 binding. So IPV4 connections are successful only when
the Linux system parameter bindv6only is set to 0 [default value].
If this parameter is set to 1, then the ipv6 wildcard only represents
any IPV6 address. Samba creates different sockets for ipv4 and ipv6
by default. This patch off sk_ipv6only to support IPV4/IPV6 connections
without creating two sockets.
Cc: stable@vger.kernel.org
Reported-by: ΕΛΕΝΗ ΤΖΑΒΕΛΛΑ <helentzavellas@yahoo.gr>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef13561d2b upstream.
Before ORing the new clock rate with the control register value read
from the hardware, the existing clock rate needs to be masked off as
otherwise the existing value will interfere with the new one.
CC: stable@vger.kernel.org
Fixes: 8596124c4c ("spi: microchip-core-qspi: Add support for microchip fpga qspi controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240508-fox-unpiloted-b97e1535627b@spud
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a4b49bb58 upstream.
regulator_get() may sometimes be called more than once for the same
consumer device, something which before commit dbe954d8f1 ("regulator:
core: Avoid debugfs: Directory ... already present! error") resulted in
errors being logged.
A couple of recent commits broke the handling of such cases so that
attributes are now erroneously created in the debugfs root directory the
second time a regulator is requested and the log is filled with errors
like:
debugfs: File 'uA_load' in directory '/' already present!
debugfs: File 'min_uV' in directory '/' already present!
debugfs: File 'max_uV' in directory '/' already present!
debugfs: File 'constraint_flags' in directory '/' already present!
on any further calls.
Fixes: 2715bb11cf ("regulator: core: Fix more error checking for debugfs_create_dir()")
Fixes: 08880713ce ("regulator: core: Streamline debugfs operations")
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240509133304.8883-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26e8383b11 upstream.
Following the failure observed with a delay of 250us, experiments were
conducted with various delays. It was found that a delay of 350us
effectively mitigated the issue.
To provide a more optimal solution while still allowing a margin for
stability, the delay is being adjusted to 500us.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Link: https://lore.kernel.org/r/20240507194603.1305750-1-lakshmiy@us.ibm.com
Fixes: 8d655e6523 ("hwmon: (ucd90320) Add minimum delay between bus accesses")
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26ff37e62 upstream.
net_alloc_generic is called by net_alloc, which is called without any
locking. It reads max_gen_ptrs, which is changed under pernet_ops_rwsem. It
is read twice, first to allocate an array, then to set s.len, which is
later used to limit the bounds of the array access.
It is possible that the array is allocated and another thread is
registering a new pernet ops, increments max_gen_ptrs, which is then used
to set s.len with a larger than allocated length for the variable array.
Fix it by reading max_gen_ptrs only once in net_alloc_generic. If
max_gen_ptrs is later incremented, it will be caught in net_assign_generic.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Fixes: 073862ba5d ("netns: fix net_alloc_generic()")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240502132006.3430840-1-cascardo@igalia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 719564737a upstream.
Theoretically rare corner case where ceil(Y) results in rounding up to
an integer. If this happens, the 1 should be carried over to the X
value.
CC: stable@vger.kernel.org
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b26bdd2e upstream.
Starting BDB version 239, hdr_dpcd_refresh_timeout is introduced to
backlight BDB data. Commit 700034566d ("drm/i915/bios: Define more BDB
contents") updated the backlight BDB data accordingly. This broke the
parsing of backlight BDB data in VBT for versions 236 - 238 (both
inclusive) and hence the backlight controls are not responding on units
with the concerned BDB version.
backlight_control information has been present in backlight BDB data
from at least BDB version 191 onwards, if not before. Hence this patch
extracts the backlight_control information for BDB version 191 or newer.
Tested on Chromebooks using Jasperlake SoC (reports bdb->version = 236).
Tested on Chromebooks using Raptorlake SoC (reports bdb->version = 251).
v2: removed checking the block size of the backlight BDB data
[vsyrjala: this is completely safe thanks to commit e163cfb4c9
("drm/i915/bios: Make copies of VBT data blocks")]
Fixes: 700034566d ("drm/i915/bios: Define more BDB contents")
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240221180622.v2.1.I0690aa3e96a83a43b3fc33f50395d334b2981826@changeid
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit c286f6a973)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a37ef7613c upstream.
Correctly set the length of the drm_event to the size of the structure
that's actually used.
The length of the drm_event was set to the parent structure instead of
to the drm_vmw_event_fence which is supposed to be read. drm_read
uses the length parameter to copy the event to the user space thus
resuling in oob reads.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 8b7de6aa84 ("vmwgfx: Rework fence event action")
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-23566
Cc: David Airlie <airlied@gmail.com>
CC: Daniel Vetter <daniel@ffwll.ch>
Cc: Zack Rusin <zack.rusin@broadcom.com>
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v3.4+
Reviewed-by: Maaz Mombasawala <maaz.mombasawala@broadcom.com>
Reviewed-by: Martin Krastev <martin.krastev@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240425192748.1761522-1-zack.rusin@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be4a2a81b6 upstream.
We don't get the right offset in that case. The GPU has
an unused 4K area of the register BAR space into which you can
remap registers. We remap the HDP flush registers into this
space to allow userspace (CPU or GPU) to flush the HDP when it
updates VRAM. However, on systems with >4K pages, we end up
exposing PAGE_SIZE of MMIO space.
Fixes: d8e408a827 ("drm/amdkfd: Expose HDP registers to user space")
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98241a774d upstream.
In current driver qcom_slim_ngd_up_worker() indefinitely
waiting for ctrl->qmi_up completion object. This is
resulting in workqueue lockup on Kthread.
Added wait_for_completion_interruptible_timeout to
allow the thread to wait for specific timeout period and
bail out instead waiting infinitely.
Fixes: a899d32486 ("slimbus: qcom-ngd-ctrl: add Sub System Restart support")
Cc: stable@vger.kernel.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240430091238.35209-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00e7d3bea2 upstream.
Fix a BUG_ON from 2009. Even if it looks "unreachable" (I didn't
really look), lets make sure by removing it, doing pr_err and return
-EINVAL instead.
Cc: stable <stable@kernel.org>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20240429193145.66543-2-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d18ca8635d upstream.
When using davinci-mcasp as CPU DAI with simple-card, there are some
conditions that cause simple-card to finish registering a sound card before
davinci-mcasp finishes registering all sound components. This creates a
non-working sound card from userspace with no problem indication apart
from not being able to play/record audio on a PCM stream. The issue
arises during simultaneous probe execution of both drivers. Specifically,
the simple-card driver, awaiting a CPU DAI, proceeds as soon as
davinci-mcasp registers its DAI. However, this process can lead to the
client mutex lock (client_mutex in soc-core.c) being held or davinci-mcasp
being preempted before PCM DMA registration on davinci-mcasp finishes.
This situation occurs when the probes of both drivers run concurrently.
Below is the code path for this condition. To solve the issue, defer
davinci-mcasp CPU DAI registration to the last step in the audio part of
it. This way, simple-card CPU DAI parsing will be deferred until all
audio components are registered.
Fail Code Path:
simple-card.c: probe starts
simple-card.c: simple_dai_link_of: simple_parse_node(..,cpu,..) returns EPROBE_DEFER, no CPU DAI yet
davinci-mcasp.c: probe starts
davinci-mcasp.c: devm_snd_soc_register_component() register CPU DAI
simple-card.c: probes again, finish CPU DAI parsing and call devm_snd_soc_register_card()
simple-card.c: finish probe
davinci-mcasp.c: *dma_pcm_platform_register() register PCM DMA
davinci-mcasp.c: probe finish
Cc: stable@vger.kernel.org
Fixes: 9fbd58cf4a ("ASoC: davinci-mcasp: Choose PCM driver based on configured DMA controller")
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240417184138.1104774-1-jpaulo.silvagoncalves@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e93a29b48 upstream.
DSPK configuration is wrong for 16-bit playback and this happens because
the client config is always fixed at 24-bit in hw_params(). Fix this by
updating the client config to 16-bit for the respective playback.
Fixes: 327ef64702 ("ASoC: tegra: Add Tegra186 based DSPK driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://msgid.link/r/20240405104306.551036-1-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90d1f14cbb upstream.
It turned out that KMSAN instruments READ_ONCE_NOCHECK(), resulting in
false positive reports, because __no_sanitize_or_inline enforced inlining.
Properly declare __no_sanitize_or_inline under __SANITIZE_MEMORY__, so
that it does not __always_inline the annotated function.
Link: https://lkml.kernel.org/r/20240426091622.3846771-1-glider@google.com
Fixes: 5de0ce85f5 ("kmsan: mark noinstr as __no_sanitize_memory")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: syzbot+355c5bb8c1445c871ee8@syzkaller.appspotmail.com
Link: https://lkml.kernel.org/r/000000000000826ac1061675b0e3@google.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57a1592784 upstream.
There are 2 issues with interrupt handling in the mxc4005 driver:
1. mxc4005_set_trigger_state() writes MXC4005_REG_INT_MASK1_BIT_DRDYE
(0x01) to INT_MASK1 to enable the interrupt, but to disable the interrupt
it writes ~MXC4005_REG_INT_MASK1_BIT_DRDYE which is 0xfe, so it enables
all other interrupt sources in the INT_SRC1 register. On the MXC4005 this
is not an issue because only bit 0 of the register is used. On the MXC6655
OTOH this is a problem since bit7 is used as TC (Temperature Compensation)
disable bit and writing 1 to this disables Temperature Compensation which
should only be done when running self-tests on the chip.
Write 0 instead of ~MXC4005_REG_INT_MASK1_BIT_DRDYE to disable
the interrupts to fix this.
2. The datasheets for the MXC4005 / MXC6655 do not state what the reset
value for the INT_MASK0 and INT_MASK1 registers is and since these are
write only we also cannot learn this from the hw. Presumably the reset
value for both is all 0, which means all interrupts disabled.
Explicitly set both registers to 0 from mxc4005_chip_init() to ensure
both masks are actually set to 0.
Fixes: 79846e33aa ("iio: accel: mxc4005: add support for mxc6655")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240326113700.56725-2-hdegoede@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89384a2b65 upstream.
The "maxim,green-led-current-microamp" property is only available for
the max30105 part (it provides an extra green LED), and must be set to
false for the max30102 part.
Instead, the max30100 part has been used for that, which is not
supported by this binding (it has its own binding).
This error was introduced during the txt to yaml conversion.
Fixes: 5a6a65b11e ("dt-bindings:iio:health:maxim,max30102: txt to yaml conversion")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240316-max30102_binding_fix-v1-1-e8e58f69ef8a@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd7eb8f83f upstream.
Currently, if an automatically freed allocation is an error pointer that
will lead to a crash. An example of this is in wm831x_gpio_dbg_show().
171 char *label __free(kfree) = gpiochip_dup_line_label(chip, i);
172 if (IS_ERR(label)) {
173 dev_err(wm831x->dev, "Failed to duplicate label\n");
174 continue;
175 }
The auto clean up function should check for error pointers as well,
otherwise we're going to keep hitting issues like this.
Fixes: 54da6a0924 ("locking: Introduce __cleanup() based infrastructure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9af503d912 upstream.
The previous patch that replaced BUG_ON by error handling forgot to
unlock the mutex in the error path.
Link: https://lore.kernel.org/all/Zh%2fHpAGFqa7YAFuM@duo.ucw.cz
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 7411055db5 ("btrfs: handle chunk tree lookup error in btrfs_relocate_sys_chunks()")
CC: stable@vger.kernel.org
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae11f04b45 upstream.
typec_register_partner() does not guarantee partner registration
to always succeed. In the event of failure, port->partner is set
to the error value or NULL. Given that port->partner validity is
not checked, this results in the following crash:
Unable to handle kernel NULL pointer dereference at virtual address xx
pc : run_state_machine+0x1bc8/0x1c08
lr : run_state_machine+0x1b90/0x1c08
..
Call trace:
run_state_machine+0x1bc8/0x1c08
tcpm_state_machine_work+0x94/0xe4
kthread_worker_fn+0x118/0x328
kthread+0x1d0/0x23c
ret_from_fork+0x10/0x20
To prevent the crash, check for port->partner validity before
derefencing it in all the call sites.
Cc: stable@vger.kernel.org
Fixes: c97cd0b4b5 ("usb: typec: tcpm: set initial svdm version based on pd revision")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240427202812.3435268-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d73572206 upstream.
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0aea736ddb upstream.
If the USB driver passes a pointer into the TRB buffer for creq, this
buffer can be overwritten with the status response as soon as the event
is queued. This can make the final check return USB_GADGET_DELAYED_STATUS
when it shouldn't. Instead use the stored wLength.
Fixes: 4d644abf25 ("usb: gadget: f_fs: Only return delayed status when len is 0")
Cc: stable <stable@kernel.org>
Signed-off-by: Chris Wulff <chris.wulff@biamp.com>
Link: https://lore.kernel.org/r/CO1PR17MB5419BD664264A558B2395E28E1112@CO1PR17MB5419.namprd17.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec6ce7075e upstream.
The OS descriptors logic had the high/low byte of w_value inverted, causing
the extended properties to not be accessible for interface != 0.
>From the Microsoft documentation:
https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-os-1-0-descriptors-specification
OS_Desc_CompatID.doc (w_index = 0x4):
- wValue:
High Byte = InterfaceNumber. InterfaceNumber is set to the number of the
interface or function that is associated with the descriptor, typically
0x00. Because a device can have only one extended compat ID descriptor,
it should ignore InterfaceNumber, regardless of the value, and simply
return the descriptor.
Low Byte = 0. PageNumber is used to retrieve descriptors that are larger
than 64 KB. The header section is 16 bytes, so PageNumber is set to 0 for
this request.
We currently do not support >64KB compat ID descriptors, so verify that the
low byte is 0.
OS_Desc_Ext_Prop.doc (w_index = 0x5):
- wValue:
High byte = InterfaceNumber. The high byte of wValue is set to the number
of the interface or function that is associated with the descriptor.
Low byte = PageNumber. The low byte of wValue is used to retrieve
descriptors that are larger than 64 KB. The header section is 10 bytes, so
PageNumber is set to 0 for this request.
We also don't support >64KB extended properties, so verify that the low byte
is 0 and use the high byte for the interface number.
Fixes: 37a3a53342 ("usb: gadget: OS Feature Descriptors support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240404100635.3215340-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>