NAND
* Cleanup for Denali driver
* Atmel: add support for new page sizes
* Atmel: fix up 'raw' mode support
* Atmel: miscellaneous cleanups
* New timing mode helpers for non-ONFI NAND
* OMAP: allow driver to be (properly) built as a module
* bcm47xx: RESET support and other cleanups
SPI NOR
* Miscellaneous cleanups, to prepare framework for wider use (some further
work still pending)
* Compile-time configuration to select 4K vs. 64K support for flash that
support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/jCH
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others,
as well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Smzi
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others, as
well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: update Shawn's email address
MAINTAINERS: condense some Tegra related entries
MAINTAINERS: add Alexandre Courbot for Tegra
MAINTAINERS: CNS3xxx and IXP4xx update.
MAINTAINERS: Add maintainers entry for Mediatek SoCs
arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500
MAINTAINERS: add a third maintainer to mach-bcm
CNS3xxx: Fix PCIe read size limit.
CNS3xxx: Fix logical PCIe topology.
CNS3xxx: Fix debug UART.
MAINTAINERS: Add entry for the Amlogic MesonX SoCs
MAINTAINERS: update ARM pxa maintainers
ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks
ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings
ARM: mvebu: Netgear RN102: Use Hardware BCH ECC
ARM: Kirkwood: Fix DT based DSA.
ARM: OMAP2+: make of_device_ids const
ARM: omap2: make arrays containing machine compatible strings const
ARM: LPC32xx: Fix reset function
ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
...
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.
If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.
As explained by Brian Norris the reasons for using a BBT are:
""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.
This has been acknowledged by several developers over the last several
years.
Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const function parameters and structs for OMAP2+ as const, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, child nodes of the gpmc node are iterated and probed
regardless of their 'status' property. This means adding 'status =
"disabled";' has no effect.
This patch changes the iteration to only probe nodes marked as
available.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- refactor m25p80.c driver for use as a general SPI NOR framework for other
drivers which may speak to SPI NOR flash without providing full SPI support
(i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6UIq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- refactor m25p80.c driver for use as a general SPI NOR framework for
other drivers which may speak to SPI NOR flash without providing full
SPI support (i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
mtd: gpmi: add gpmi support for imx6sx
mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
mtd: bf5xx_nand: use the managed version of kzalloc
mtd: pxa3xx_nand: make the driver work on big-endian systems
mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
mtd: nand: r852: correct write_buf loop bounds
mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
mtd: nand_bbt: remove unused variable
mtd: maps: sc520cdp: fix warnings
mtd: slram: fix unused variable warning
mtd: pfow: remove unused variable
mtd: lpddr: fix Kconfig dependency, for I/O accessors
mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
mtd: nand: Warn the user if the selected ECC strength is too weak
mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
...
This patch add support for BCH16_ECC in GPMC (controller) driver:
- extends configuration space to include BCH16 registers
- extends parsing of DT binding for selecting BCH16 ecc-scheme
Signed-off-by: Pekon Gupta <pekon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least the smc91x driver expects the device to be at 0x300
offset from bus base address. This does not work currently
for GPMC when booted in device tree mode as it attempts to
remap the the allocated GPMC partition to the address
configured by the device tree plus the device offset.
Note that this works just fine when booted with legacy mode.
Let's fix the issue by just ignoring any device specific
offset while remapping. And let's make sure the remap
address confirms to the GPMC 16MB minimum granularity
as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits.
Otherwise we can get something like this:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If gpmc_cs_remap() fails we will get an error because we are calling
release_resource() on an uninitialized resource. Let's fix that by
checking the resource flags. And while at it, let's also make
gpmc_cs_delete_mem() use the res pointer that we already have to
avoid confusion.
Without this patch we can get the following error:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
(gpmc_cs_free+0x94/0xc8)
(gpmc_probe_generic_child+0x178/0x1ec)
(gpmc_probe_dt+0x1bc/0x2cc)
(gpmc_probe+0x250/0x44c)
(platform_drv_probe+0x3c/0x6c)
(really_probe+0x74/0x208)
(driver_probe_device+0x34/0x50)
(bus_for_each_drv+0x60/0x8c)
(device_attach+0x80/0xa4)
(bus_probe_device+0x88/0xb0)
(device_add+0x320/0x450)
(of_platform_device_create_pdata+0x80/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)
(pdata_quirks_init+0x30/0x48)
(customize_machine+0x20/0x48)
(do_one_initcall+0x2c/0x14c)
(do_basic_setup+0x98/0xd8)
(kernel_init_freeable+0x12c/0x1e0)
(kernel_init+0x8/0xf0)
(ret_from_fork+0x14/0x2c)
Code: e1a04000 e59f0070 eb195136 e5942010 (e5923018)
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: tony Lindgren <tony@atomide.com>
Fixes: commit 75d3625e0e
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for ONENAND driver to probe later. However this does
not happen if generic MTD_ONENAND framework is built as module (CONFIG_MTD_ONENAND=m).
Therefore, when MTD/ONENAND and MTD/ONENAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
ONENAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_ONENAND=y || CONFIG_MTD_ONENAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: commit bc6b1e7b86
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for NAND driver to probe later. However this does
not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m).
Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
NAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Commit f2bf0e72d0 (ARM: OMAP2+: Add minimal 8250 support
for GPMC) added support for using bootloader timings for some
devices. Turns out we can do the same by looking at the compatible
flags of the child without adding a new function as smc91x has
a similar issue as 8250 with the bootloader timings.
And let's fix the 8250 naming, we should use the device type as
the name like uart instead of 8250 for zoom dts file.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
* Other general cleanups (removing unused functions, options, variables,
fields; use correct interfaces)
* Fix BUG() for new odd-sized NAND, which report non-power-of-2 dimensions via
ONFI
* Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
* Improve differentiation between SLC and MLC NAND -- this clarifies an ABI
issue regarding the MTD "type" (in sysfs and in ioctl(MEMGETINFO)), where
the MTD_MLCNANDFLASH type was present but inconsistently used
* Extend GPMI NAND to support multi-chip-select NAND for some platforms
* Many improvements to the OMAP2/3 NAND driver, including an expanded DT
binding to bring us closer to mainline support for some OMAP systems
* Fix a deadlock in the error path of the Atmel NAND driver probe
* Correct the error codes from MTD mmap() to conform to POSIX and the Linux
Programmer's Manual. This is an acknowledged change in the MTD ABI, but I
can't imagine somebody relying on the non-standard -ENOSYS error code
specifically. Am I just being unimaginative? :)
* Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
* More? Read the log!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=z5qO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
OMAP NAND driver support multiple ECC scheme, which can used in different
flavours, depending on in-build Hardware engines present on SoC.
This patch updates following in DT bindings related to sectionion of ecc-schemes
- ti,elm-id: replaces elm_id (maintains backward compatibility)
- ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme
depends on ti,elm-id. (supported values ham1, bch4, and bch8)
- maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode)
Below table shows different flavours of ecc-schemes supported by OMAP devices
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
|(requires CONFIG_MTD_NAND_ECC_BCH) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
|(requires CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id in DT) | | |
+---------------------------------------+---------------+---------------+
To optimize footprint of omap2-nand driver, selection of some ECC schemes
also require enabling following Kconfigs, in addition to setting appropriate
DT bindings
- Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software
- Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Just initialize things using the bootloader timings like
we've been doing for the legacy booting too. It should be
possible to patch in the GPMC timings for the based on the
TL16CP743C/TL16C754C manual at:
http://www.ti.com/lit/ds/slls644g/slls644g.pdf
Signed-off-by: Tony Lindgren <tony@atomide.com>
When CONFIG_ARM_LPAE=y the following build warning is generated:
arch/arm/mach-omap2/gpmc.c:1495:4: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
'gpmc_irq_start' is mostly used as 'int', and for a variable, do not
suggest to only use 'unsigned' as its type, so use 'int' instead of
'unsigned' for variable 'gpmc_irq_start'.
Also it will fix the related issue (dummy the real world failure):
arch/arm/mach-omap2/gpmc.c:728:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cocci spatch "ptr_ret.spatch"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPMC is hardware controller for external memory interfaces.
This patch adds suspend/resume support for GPMC driver.
It also preserves GPMC register configurations across device low-power states
in which GPMC hardware can be powered-off.
gpmc_suspend()/gpmc_resume() are called by default by core PM framework as part
of driver's runtime PM callbacks.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support for pm_runtime add to GPMC driver.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables usage of DT property 'gpmc,num-cs' as already documented in
Documentation/devicetree/bindings/bus/ti-gpmc.txt
Though GPMC hardware supports upto 8 chip-selects, but all chip-selects may
not be available for use because:
- chip-select pin may not be bonded out at SoC device boundary.
- chip-select pin-mux may conflict with other pins usage.
- board level constrains.
gpmc,num-cs allows user to configure maximum number of GPMC chip-selects
available for use on any given platform. This ensures:
- GPMC child nodes having chip-selects within allowed range are only probed.
- And un-used GPMC chip-selects remain blocked.(may be for security reasons).
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8c8a777 (ARM: OMAP2+: Add function to read GPMC settings from
device-tree) added a device-tree property "gpmc,device-nand" to indicate
is the GPMC child device is NAND. This commit should have updated the
GPMC NAND documentation (Documentation/devicetree/bindings/mtd/gpmc-nand.txt)
to list the property "gpmc,device-nand" as a required property and also
updated the example. However, this property is redundant and not needed
because the GPMC child device node for NAND is called "nand". Therefore,
remove this property.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP devices support various NAND transfer modes.
Currently all device-tree definitions will use the default "prefetch
polled" mode, so this patch enables the transfer mode to be specified
in the device-tree.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If any of the GPMC child nodes fails, this shouldn't make the
whole gpmc_probe_dt() function to fail. It is better to just
WARN and allow other devices probe function to succeed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The GPMC DT probe function use for_each_node_by_name() to search
child device nodes of the GPMC controller. But this function does
not use the GPMC device node as the root of the search and instead
search across the complete Device Tree.
This means that any device node on the DT that is using any of the
GPMC child nodes names searched for will be returned even if they
are not connected to the GPMC, making the gpmc_probe_xxx_child()
function to fail.
Fix this by using the GPMC device node as the search root so the
search will be restricted to its children.
Reported-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Besides being used to interface with external memory devices,
the General-Purpose Memory Controller can be used to connect
Pseudo-SRAM devices such as ethernet controllers to OMAP2+
processors using the TI GPMC as a data bus.
This patch allows an ethernet chip to be defined as an GPMC
child device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The gpmc_probe_nor_child() function is used in the GPMC driver to
configure the GPMC for a NOR child device node.
But this function is quite generic and all the NOR specific configuration
is made by the driver of the actual NOR flash memory used.
Other Pseudo-SRAM devices such as ethernet controllers need a similar
setup so by making this function generic it can be used for those too.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
gpmc_probe_nor_child() calls of_platform_device_create() to create a
platform device for the NOR child. If this function fails the value
of ret is returned to the caller but this value is zero since it was
assigned the return of a previous call to gpmc_cs_program_settings()
that had to succeed or otherwise gpmc_probe_nor_child() would have
returned before.
This means that if of_platform_device_create() fails, 0 will be returned
to the caller instead of an appropriate error code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
When the GPMC driver is probed, we call gpmc_mem_init() to see which
chip-selects have already been configured and enabled by the boot-loader
and allocate space for them. If we fail to allocate space for one
chip-select, then we return failure from the probe and the GPMC driver
will not be available.
Rather than render the GPMC useless for all GPMC devices, if we fail to
allocate space for one chip-select print a warning and disable the
chip-select. This way other GPMC clients can still be used.
There is no downside to this approach, because all GPMC clients need to
request a chip-select before they can use the GPMC and on requesting a
chip-select, if memory has not already been reserved for the chip-select
then it will be.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
With commit 21cc2bd (ARM: OMAP2+: Remove apollon board support) the
variable "boot_rom_space" is now not needed and the code surrounding
this variable can be cleaned up and simplified. Remove unnecessary
definitions and clean-up the comment as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Each GPMC chip-select can be configured to map 16MB, 32MB, 64MB or 128MB
of address space. The physical base address where a chip-select starts
is also configurable and must be aligned on a boundary that is equal to
or greater than the size of the address space mapped bt the chip-select.
When enabling a GPMC chip-select, ensure that the base address is aligned
to the appropriate boundary.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
NOR flash is not currently supported when booting with device-tree
on OMAP2+ devices. Add support to detect and configure NOR devices
when booting with device-tree.
Add documentation for the TI GPMC NOR binding.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Some of the GPMC timings parameters are currently missing from the GPMC
device-tree binding. Add these parameters to the binding documentation
as well as code to read them. Also add either "-ps" or "-ns" suffix to
the GPMC timing properties to indicate whether the timing is in
picoseconds or nanoseconds.
The existing code in gpmc_read_timings_dt() is checking the value of
of_property_read_u32() and only is successful storing the value read
in the gpmc_timings structure. Checking the return value in this case
is not necessary and we can simply read the value, if present, and
store directly in the gpmc_timings structure. Therefore, simplify the
code by removing these checks.
The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
is also incorrect as it is applicable to all OMAP3+ devices. So correct
this too.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Adds a function to read the various GPMC chip-select settings from
device-tree and store them in the gpmc_settings structure.
Update the GPMC device-tree binding documentation to describe these
options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
With the addition of the gpmc_cs_program_settings(), we no longer need
or use gpmc_cs_configure() to configure some of the GPMC chip-select
options. So rename the function to gpmc_configure() and remove code that
modifies options in the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no common function for configuring these options and
various devices set these options by either programming the GPMC CONFIG1
register directly or by calling gpmc_cs_configure() to set some of the
options.
Add a new function for configuring all of the GPMC options. Having a common
function for configuring this options will simplify code and ease the
migration to device-tree.
Also add a new capability flag to detect devices that support the
address-address-data multiplexing mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no central structure for storing all these options
when configuring the GPMC for a given device. Some of the options are
stored in the GPMC timing structure and some are directly programmed
into the GPMC configuration register. Add a new structure to store
these options and convert code to use this structure. Adding this
structure will allow us to create a common function for configuring
these options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The GPMC has wait-pin signals that can be assigned to a chip-select
to monitor the ready signal of an external device. Add a variable to
indicate the total number of wait-pins for a given device. This will
allow us to detect if the wait-pin being selected is valid or not.
When booting with device-tree read the number of wait-pins from the
device-tree blob. When device-tree is not used set the number of
wait-pins to 4 which is valid for OMAP2-5 devices. Newer devices
that have less wait-pins (such as AM335x) only support booting with
device-tree and so hard-coding the wait-pin number when not using
device-tree is fine.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
This check is done before the call to gpmc_cs_reserved() and
gpmc_cs_set_reserved() and it's redundant to do it again in each
function. This simplifies the code a bit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Currently gpmc_cs_reserved() return value is somewhat inconsistent,
returning a negative value on an error condition, a positive value
if the chip select is reserved and zero if it's available.
Fix this by returning a boolean value as the function name suggests:
* true if the chip select is reserved,
* false if it's available
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
This function is not used anywhere, so it's safe to remove it.
This means less code to maintain.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
This patch marks a bunch of functions that are local
to gpmc.c file only as static.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
When setting the GPMC device type, make sure any previous
bits are cleared down, before applying the new setting.
For OMAP4+ devices MUXADDDATA is a 2-bit field (bits 9:8)
where as for OMAP2/3 devices it was only a one bit field
(bit 9). For OMAP2/3 devices bit 8 is reserved and the
OMAP documentation says to write a 0 to this bit. So
clearing bit 8 on OMAP2/3 devices should not be a problem.
Hence update the code to handle both bits 8 and 9 for all
devices.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
[jon-hunter@ti.com: updated changelog]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Consistently check errors using the usual method used in the kernel
for much of its history. For instance:
int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t)
{
int div;
div = gpmc_calc_divider(t->sync_clk);
if (div < 0)
return div;
static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
{
...
return gpmc_cs_set_timings(cs, t);
.....
ret = gpmc_set_async_mode(gpmc_onenand_data->cs, &t);
if (IS_ERR_VALUE(ret))
return ret;
So, gpmc_cs_set_timings() thinks any negative return value is an error,
but where we check that in higher levels, only a limited range are
errors...
There is only _one_ use of IS_ERR_VALUE() in arch/arm which is really
appropriate, and that is in arch/arm/include/asm/syscall.h:
static inline long syscall_get_error(struct task_struct *task,
struct pt_regs *regs)
{
unsigned long error = regs->ARM_r0;
return IS_ERR_VALUE(error) ? error : 0;
}
because this function really does have to differentiate between error
return values and addresses which look like negative numbers (eg, from
mmap()).
So, here's a patch to remove them from OMAP, except for the above.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Philip Avinash <avinashphilip@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <tony@atomide.com>
