Restarting the transmitter even if the circ buffer is empty may be
necessary to push out remaining data when the port is restarted after
being stopped.
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of disabling the IRQ, use the spin lock to serialize accesses to
the HW. This protects the driver from interference of non-IRQ callbacks
with each other and makes the driver more consistent in its
serialization method.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Early console functions are only used during the early boot stage.
This change just saves a small amount of memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_console_setup() checks port->mapbase != 0, but the port may
not be initialized yet even if this condition is met [e.g., ioremap()
may have failed]. Check port->membase != NULL instead, similar to
cdns_early_console_setup().
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of cdns_uart_readl() and cdns_uart_writel() and just call
readl() and writel() directly.
Most of the patch was created by search-and-replace (I had to convert a
few lines manually, and break some lines longer than 80 columns):
* s/cdns_uart_readl(/readl(port->membase + /g
* s/cdns_uart_writel(\([^,]*\),/writel(\1, port->membase +/g
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_get_port() sets port->iobase = 1 to "mark port in use", but
this "in use" condition is not checked anywhere else in the code. So
remove the line, keeping port->iobase = 0 (which also makes more sense).
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code assumes that the array cdns_uart_port[] has dimension
CDNS_UART_NR_PORTS, so let us define it this way.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register space size is 0x1000, and this value [not 0xfff] should be
provided to request_mem_region(), ioremap(), etc.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All instances of "ttyPS" use this macro except for this one. Convert
it.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of flushing the RX FIFO breaks in a number of cases,
it is impossible to ensure an complete flush of the RX FIFO due to the
hardware not allowing the use of the FIFOs when the receiver is disabled
(Reading from the FIFO register does not remove it from the FIFO when
the RX_EN=0 or RX_DIS=1). Additionally during an initial set_termios
call where RX_DIS=1 causes a hang waiting forever for the RX FIFO to
empty. On top of this the FIFO will be cleared by the use of the RXRST
bits on the Control Register, making the RX flush pointless (as it does
not preserve the data read anyway).
Due to the TXRST the TX FIFO and transmitter can be interrupted during
frame trasmission, causing corruption and additionally data lost in the
FIFO. Most other serial drivers do not flush or clear the FIFOs during
a termios configuration change and as such do not have issues with
corruption. For this UART controller is it required that the TXRST/RXRST
bit be flagged during the change, this means that the data in the FIFO
will be dropped when changing configuration. In order to prevent data
loss and corruption of the transmitted data, wait until the TX FIFO is
empty before changing the configuration. The performance of this may
cause the set_termios call to take a longer amount of time especially
on lower baud rates, however it is comparable to the same performance
hit that a console_write call costs.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Acked-by: Anirudha Sarangi <anirudh@xilinx.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for setting the state of the DTR and RTS signals.
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add earlycon support for the cadence serial port.
This is based on recent patches:
"tty/serial: pl011: add generic earlycon support"
(sha1: 0d3c673e78)
"tty/serial: add arm/arm64 semihosting earlycon"
(sha1: d50d7269eb)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_empty() callback currently checks the TXEMPTY bit in the interrupt
status register to decided whether the FIFO should be reported as empty or
not. The bit in this register gets set when the FIFO state transitions from
non-empty to empty but is cleared again in the interrupt handler. This means
it is not suitable to be used to decided whether the FIFO is currently empty
or not. Instead use the TXEMPTY bit from the status register which will be
set as long as the FIFO is empty.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zynq's UART is Cadence IP. Make this visible in the prompt in kconfig
and additional comments in the driver.
This also renames functions and symbols, as far as possible without
breaking user space API, to reflect the Cadence origin. This is achieved
through simple search and replace:
- s/XUARTPS/CDNS_UART/g
- s/xuartps/cdns_uart/g
The only exceptions are PORT_XUARTPS and the driver name, which stay as is,
due to their exposure to user space. As well as the - no legacy -
compatibility string 'xlnx,xuartps'
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A comment states, that, according to the data sheet, to enable
interrupts the disable register should be written, but the enable
register could be left untouched. And it suspsects a HW bug requiring
to write both.
Reviewing the data sheet, these statements seem wrong. Just as one would
expect. Writing to the enable/disable register enables/disables
interrupts.
Hence the misleading comment and needless write to the disable register
are removed from the enable sequence.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A lot of read-modify-write sequences used a one-line statement which
nests a readl() within a writel(). Convert this into code sequences that
make the three steps more obvious.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print a warning if the clock notifier rejects a clock frequency change
to facilitate debugging (see:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/304329/focus=304379)
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is all white space and comment clean up. Mostly reformatting
comments.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register port numbers according to order in DT aliases.
If aliases are not defined, order in DT is used.
If aliases are defined, register port id based
on that.
This patch ensures proper ttyPS0/1 assignment.
[soren]: Combined integer declarations in probe(), removed warning message
if no alias is found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock notifiers are only available when CONFIG_COMMON_CLK is enabled.
Hence all notifier related code has to be protected by corresponsing
ifdefs.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is enabled and CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
is not, a forward declaration of the uart_driver struct is not
included, leading to a build error due to an undeclared variable.
Fixing this by moving the definition of the struct uart_driver before
the definition of the suspend/resume callbacks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize varibles for which a 'may be used uninitalized' warning is
issued.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement suspend and resume callbacks in order to support system
suspend/hibernation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a clock notifier to dynamically handle frequency changes of the
input clock by reprogramming the UART in order to keep the baud rate
constant.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original algorithm to find the best baud rate dividers does not necessarily
find the best set of dividers. And in the worst case may even write illegal
values to the hardware.
The new function should make better use of the hardware capabilities and be able
to provide valid settings for a wider range of baud rates and also input clocks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that under certain circumstances xuartps_console_write is entered
while the UART disabled. When this happens the code will busy loop in
xuartps_console_putchar, since the character is never written and the TXEMPTY
flag is never set. The result is a system lockup. This patch force enables the
UART for the duration of xuartps_console_write to avoid this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to use the 64 byte FIFO depth and fix the issue
by clearing the txempty interrupt in isr status for tx
after filling in data in start_tx function
Signed-off-by: Suneel Garapati <suneelg@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cadence UART does not do break detection, even if the
datasheet says it does. This patch adds break detection in
software (tested in 8N1 mode only) and enables SYSRQ,
allowing for Break-g to enter KDB and all the other goodies.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Currently Zynq does not support suspend/resume.
The driver callbacks are never used or tested, broken and using the old
PM interface.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Boot ROM has an issue which will cause the driver to
lock up as pending irqs are not being cleared. With them
cleared it prevents that issue.
This patch is needed for the current (3.9-rc3) mainline kernel. I guess
it went unnoticed, because it was only tested with u-boot up until now.
And u-boot maybe handles this.
[s.trumtrar@pengutronix.de: cherry-picked from linux-xlnx.git]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datesheet clearly states, that writing low bits to the
XUARTPS_IDR register have no effect. Remove the write.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__exit_p() need to be removed after the __devexit
removal from the driver.
Warning log:
drivers/tty/serial/xilinx_uartps.c:996:12:
warning: 'xuartps_remove' defined but not used [-Wunused-function]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for specifying clock information for the uart clk via the
device tree. This eliminates the need to hardcode rates in the device
tree.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Zynq platform requires the use of CONFIG_OF. Remove the #ifdef
conditionals in the uartps driver. Make dependency explicit in Kconfig.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are cleaning up the issue that means module.h is omnipresent.
These tty users are the people who implictly are relying on that.
Fix up the real users to call out the include that they really need.
In the case of jsm_driver.c file, it had moduleparam.h but that
isn't enough and it needs the full module.h
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
linux/tty_flip.h is included in linux/serial_core.h. But this may (and
will) change in the future. Then we would get build errors such as:
.../tty/serial/max3107.c: In function ‘put_data_to_circ_buf’:
.../tty/serial/max3107.c:149:2: error: implicit declaration of function ‘tty_insert_flip_string’
So fix all the drviers which call tty flip buffer helpers to really
include linux/tty_flip.h. And also make sure that those include
linux/tty.h when operating with struct tty_struct.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Xilinx PS Uart is used on the new ARM based SoC. This
UART is not compatible with others such that a seperate
driver is required.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
