As phylink gained generic support for PHYs with rate matching via PAUSE
frames, the phylink_mac_link_up() method will be called with the maximum
speed and with rx_pause=true if rate matching is in use. This means that
setups with 2500base-x as the SERDES protocol between the MAC/PCS and
the PHY now work with no need for the driver to do anything special.
Tested with fsl-ls1028a-qds-7777.dts.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop the custom implementation of phylink_validate() in favor of the
generic one, which requires config->mac_capabilities to be set.
This was used up until now because of the possibility of being paired
with Aquantia PHYs with support for rate matching. The phylink framework
gained generic support for these, and knows to advertise all 10/100/1000
lower speed link modes when our SERDES protocol is 2500base-x
(fixed speed).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are Gen3 Aquantia N-BASET PHYs which support 5GBASE-T,
2.5GBASE-T, 1000BASE-T and 100BASE-TX (not 10G); also EEE, Sync-E,
PTP, PoE.
The 112 is a single PHY package, the 412 is a quad PHY package.
The system-side SERDES interface of these PHYs selects its protocol
depending on the negotiated media side link speed. That protocol can be
1000BASE-X, 2500BASE-X, 10GBASE-R, SGMII, USXGMII.
The configuration of which SERDES protocol to use for which link speed
is made by firmware; even though it could be overwritten over MDIO by
Linux, we assume that the firmware provisioning is ok for the board on
which the driver probes.
For cases when the system side runs at a fixed rate, we want phylib/phylink
to detect the PAUSE rate matching ability of these PHYs, so we need to
use the Aquantia rather than the generic C45 driver. This needs
aqr107_read_status() -> aqr107_read_rate() to set phydev->rate_matching,
as well as the aqr107_get_rate_matching() method.
I am a bit unsure about the naming convention in the driver. Since
AQR107 is a Gen2 PHY, I assume all functions prefixed with "aqr107_"
rather than "aqr_" mean Gen2+ features. So I've reused this naming
convention.
I've tested PHY "SGMII" statistics as well as the .link_change_notify
method, which prints:
Aquantia AQR412 mdio_mux-0.4:00: Link partner is Aquantia PHY, FW 4.3, fast-retrain downshift advertised, fast reframe advertised
Tested SERDES protocols are usxgmii and 2500base-x (the latter with
PAUSE rate matching). Tested link modes are 100/1000/2500 Base-T
(with Aquantia link partner and with other link partners). No notable
events observed.
The placement of these PHY IDs in the driver is right before AQR113C,
a Gen4 PHY.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Fix sparse warning in the new nft_inner expression, reported
by Jakub Kicinski.
2) Incorrect vlan header check in nft_inner, from Peng Wu.
3) Two patches to pass reset boolean to expression dump operation,
in preparation for allowing to reset stateful expressions in rules.
This adds a new NFT_MSG_GETRULE_RESET command. From Phil Sutter.
4) Inconsistent indentation in nft_fib, from Jiapeng Chong.
5) Speed up siphash calculation in conntrack, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: conntrack: use siphash_4u64
netfilter: rpfilter/fib: clean up some inconsistent indenting
netfilter: nf_tables: Introduce NFT_MSG_GETRULE_RESET
netfilter: nf_tables: Extend nft_expr_ops::dump callback parameters
netfilter: nft_inner: fix return value check in nft_inner_parse_l2l3()
netfilter: nft_payload: use __be16 to store gre version
====================
Link: https://lore.kernel.org/r/20221115095922.139954-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The NFP documentation is updated to include information about Corigine,
and the new NFP3800 chips. The 'Acquiring Firmware' section is updated
with new information about where to find firmware.
Two new sections are added to expand the coverage of the documentation.
The new sections include:
- Devlink Info
- Configure Device
Signed-off-by: Walter Heymans <walter.heymans@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221115090834.738645-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Felix Fietkau says:
====================
mtk_eth_soc rx vlan offload improvement + dsa hardware untag support
This series improves rx vlan offloading on mtk_eth_soc and extends it to
support hardware DSA untagging where possible.
This improves performance by avoiding calls into the DSA tag driver receive
function, including mangling of skb->data.
This is split out of a previous series, which added other fixes and
multiqueue support
====================
Link: https://lore.kernel.org/r/20221114124214.58199-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
x25_lapb_receive_frame() using skb_copy() to get a private copy of
skb, the new skb should be freed in the undersized/fragmented skb
error handling path. Otherwise there is a memory leak.
Fixes: cb101ed2c3 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20221114110519.514538-1-weiyongjun@huaweicloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If ag71xx_hw_enable() fails, call phylink_disconnect_phy() to clean up.
And if phylink_of_phy_connect() fails, nothing needs to be done.
Compile tested only.
Fixes: 892e09153f ("net: ag71xx: port to phylink")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221114095549.40342-1-liujian56@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- pass the tag to DSA via metadata dst
- disabled on 7986 for now, since it's not working yet
- disabled if a MAC is enabled that does not use DSA
This improves performance by bypassing the DSA tag driver and avoiding extra
skb data mangling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Keep the vlan rx offload feature in sync across all netdevs belonging to the
device, since the feature is global and can't be turned off per MAC
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the id from the DMA descriptor instead of hardcoding 802.1q
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a metadata dst is present with the type METADATA_HW_PORT_MUX on a dsa cpu
port netdev, assume that it carries the port number and that there is no DSA
tag present in the skb data.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=VxQ6
-----END PGP SIGNATURE-----
AMerge tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfx fixes from David Howells:
"Two fixes, affecting the functions that iterates over the pagecache
unmarking or unlocking pages after an op is complete:
- xas_for_each() loops must call xas_retry() first thing and
immediately do a "continue" in the case that the extracted value is
a special value that indicates that the walk raced with a
modification. Fix the unlock and unmark loops to do this.
- The maths in the unlock loop is dodgy as it could, theoretically,
at some point in the future end up with a starting file pointer
that is in the middle of a folio. This will cause a subtraction to
go negative - but the number is unsigned. Fix the maths to use
absolute file positions instead of relative page indices"
* tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Fix dodgy maths
netfs: Fix missing xas_retry() calls in xarray iteration
- Fix packed_inode invalid access when reading fragments on crafted
images;
- Add a missing erofs_put_metabuf() in an error path in fscache mode;
- Fix incorrect `count' for unmapped extents in fscache mode;
- Fix use-after-free of fsid and domain_id string when remounting;
- Fix missing xas_retry() in fscache mode.
-----BEGIN PGP SIGNATURE-----
iIcEABYIAC8WIQThPAmQN9sSA0DVxtI5NzHcH7XmBAUCY3OcchEceGlhbmdAa2Vy
bmVsLm9yZwAKCRA5NzHcH7XmBCzgAP92t7Lfu7gBuyhXfCJwJVFK0Iku8j9mhOiT
+C/RVB+9zQEAk/2vy3ULcGN5k6k2q7OgEzNxQ/jM3hVQnoK+sQzwVwA=
=XHmr
-----END PGP SIGNATURE-----
Merge tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"Most patches randomly fix error paths or corner cases in fscache mode
reported recently. One fixes an invalid access relating to fragments
on crafted images.
Summary:
- Fix packed_inode invalid access when reading fragments on crafted
images
- Add a missing erofs_put_metabuf() in an error path in fscache mode
- Fix incorrect `count' for unmapped extents in fscache mode
- Fix use-after-free of fsid and domain_id string when remounting
- Fix missing xas_retry() in fscache mode"
* tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix missing xas_retry() in fscache mode
erofs: fix use-after-free of fsid and domain_id string
erofs: get correct count for unmapped range in fscache mode
erofs: put metabuf in error path in fscache mode
erofs: fix general protection fault when reading fragment
DE_CFG contains the LFENCE serializing bit, restore it on resume too.
This is relevant to older families due to the way how they do S3.
Unify and correct naming while at it.
Fixes: e4d0e84e49 ("x86/cpu/AMD: Make LFENCE a serializing instruction")
Reported-by: Andrew Cooper <Andrew.Cooper3@citrix.com>
Reported-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the dodgy maths in netfs_rreq_unlock_folios(). start_page could be
inside the folio, in which case the calculation of pgpos will be come up
with a negative number (though for the moment rreq->start is rounded down
earlier and folios would have to get merged whilst locked)
Alter how this works to just frame the tracking in terms of absolute file
positions, rather than offsets from the start of the I/O request. This
simplifies the maths and makes it easier to follow.
Fix the issue by using folio_pos() and folio_size() to calculate the end
position of the page.
Fixes: 3d3c950467 ("netfs: Provide readahead and readpage netfs helpers")
Reported-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
cc: linux-cachefs@redhat.com
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/Y2SJw7w1IsIik3nb@casper.infradead.org/
Link: https://lore.kernel.org/r/166757988611.950645.7626959069846893164.stgit@warthog.procyon.org.uk/ # v2
netfslib has a number of places in which it performs iteration of an xarray
whilst being under the RCU read lock. It *should* call xas_retry() as the
first thing inside of the loop and do "continue" if it returns true in case
the xarray walker passed out a special value indicating that the walk needs
to be redone from the root[*].
Fix this by adding the missing retry checks.
[*] I wonder if this should be done inside xas_find(), xas_next_node() and
suchlike, but I'm told that's not an simple change to effect.
This can cause an oops like that below. Note the faulting address - this
is an internal value (|0x2) returned from xarray.
BUG: kernel NULL pointer dereference, address: 0000000000000402
...
RIP: 0010:netfs_rreq_unlock+0xef/0x380 [netfs]
...
Call Trace:
netfs_rreq_assess+0xa6/0x240 [netfs]
netfs_readpage+0x173/0x3b0 [netfs]
? init_wait_var_entry+0x50/0x50
filemap_read_page+0x33/0xf0
filemap_get_pages+0x2f2/0x3f0
filemap_read+0xaa/0x320
? do_filp_open+0xb2/0x150
? rmqueue+0x3be/0xe10
ceph_read_iter+0x1fe/0x680 [ceph]
? new_sync_read+0x115/0x1a0
new_sync_read+0x115/0x1a0
vfs_read+0xf3/0x180
ksys_read+0x5f/0xe0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Changes:
========
ver #2)
- Changed an unsigned int to a size_t to reduce the likelihood of an
overflow as per Willy's suggestion.
- Added an additional patch to fix the maths.
Fixes: 3d3c950467 ("netfs: Provide readahead and readpage netfs helpers")
Reported-by: George Law <glaw@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-cachefs@redhat.com
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/166749229733.107206.17482609105741691452.stgit@warthog.procyon.org.uk/ # v1
Link: https://lore.kernel.org/r/166757987929.950645.12595273010425381286.stgit@warthog.procyon.org.uk/ # v2
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal and type-cover HID devices
(including sensors, touchpad, keyboard, and other miscellaneous devices)
on the Surface Pro 9.
This does not include support for a tablet-mode switch yet, as that is
now handled via the POS subsystem (unlike the Surface Pro 8, where it is
handled via the KIP subsystem) and therefore needs further changes.
While we're at it, also add the missing comment for the Surface Pro 8.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently, we check any received packet whether we have already seen it
previously, regardless of the packet type (sequenced / unsequenced). We
do this by checking the sequence number. This assumes that sequence
numbers are valid for both sequenced and unsequenced packets. However,
this assumption appears to be incorrect.
On some devices, the sequence number field of unsequenced packets (in
particular HID input events on the Surface Pro 9) is always zero. As a
result, the current retransmission check kicks in and discards all but
the first unsequenced packet, breaking (among other things) keyboard and
touchpad input.
Note that we have, so far, only seen packets being retransmitted in
sequenced communication. In particular, this happens when there is an
ACK timeout, causing the EC (or us) to re-send the packet waiting for an
ACK. Arguably, retransmission / duplication of unsequenced packets
should not be an issue as there is no logical condition (such as an ACK
timeout) to determine when a packet should be sent again.
Therefore, remove the retransmission check for unsequenced packets
entirely to resolve the issue.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Like the Acer Switch 10 (SW5-012) and Acer Switch 10 (S1003) models
the Acer Switch V 10 (SW5-017) supports reporting SW_TABLET_MODE
through acer-wmi.
Add a DMI quirk for the SW5-017 setting force_caps to ACER_CAP_KBD_DOCK
(these devices have no other acer-wmi based functionality).
Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221111111639.35730-1-hdegoede@redhat.com
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before asus_wmi_set_xusb2pr() returns.
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221111100752.134311-1-wangxiongfeng2@huawei.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The current logic in the Intel PMC driver will forcefully attach it
when detecting any CPU on the intel_pmc_core_platform_ids array,
even if the matching ACPI device is not present.
There's no checking in pmc_core_probe() to assert that the PMC device
is present, and hence on virtualized environments the PMC device
probes successfully, even if the underlying registers are not present.
Before commit 21ae435709 ("platform/x86: intel_pmc_core: Substitute PCI
with CPUID enumeration") the driver would check for the presence of a
specific PCI device, and that prevented the driver from attaching when
running virtualized.
Fix by only forcefully attaching the PMC device when not running
virtualized. Note that virtualized platforms can still get the device
to load if the appropriate ACPI device is present on the tables
provided to the VM.
Make an exception for the Xen initial domain, which does have full
hardware access, and hence can attach to the PMC if present.
Fixes: 21ae435709 ("platform/x86: intel_pmc_core: Substitute PCI with CPUID enumeration")
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221110163145.80374-1-roger.pau@citrix.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Previously, the s2idle quirk was only active for the 21A0 machine type
of the P14s Gen2a product. This also enables it for the second 21A1 type,
thus reducing wake-up times from s2idle.
Signed-off-by: Lennard Gäher <gaeher@mpi-sws.org>
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2181
Link: https://lore.kernel.org/r/20221108072023.17069-1-gaeher@mpi-sws.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add new a new ACPI ID AMDI0009 used by upcoming AMD platform to the pmc
supported list of devices.
Cc: stable@vger.kernel.org # 6.0
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20221109083346.361603-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch fixes a frame size warning, reported by kernel test robot.
>> net/dcb/dcbnl.c:1230:1: warning: the frame size of 1244 bytes is
>> larger than 1024 bytes [-Wframe-larger-than=]
The getapptrust part of dcbnl_ieee_fill is moved to a separate function,
and the selector array is now dynamically allocated, instead of stack
allocated.
Tested on microchip sparx5 driver.
Fixes: 6182d5875c ("net: dcb: add new apptrust attribute")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20221114092950.2490451-1-daniel.machon@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The bridge driver can offload VLANs to the underlying hardware either
via switchdev or the 8021q driver. When the former is used, the VLAN is
marked in the bridge driver with the 'BR_VLFLAG_ADDED_BY_SWITCHDEV'
private flag.
To avoid the memory leaks mentioned in the cited commit, the bridge
driver will try to delete a VLAN via the 8021q driver if the VLAN is not
marked with the previously mentioned flag.
When the VLAN protocol of the bridge changes, switchdev drivers are
notified via the 'SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL' attribute, but
the 8021q driver is also called to add the existing VLANs with the new
protocol and delete them with the old protocol.
In case the VLANs were offloaded via switchdev, the above behavior is
both redundant and buggy. Redundant because the VLANs are already
programmed in hardware and drivers that support VLAN protocol change
(currently only mlx5) change the protocol upon the switchdev attribute
notification. Buggy because the 8021q driver is called despite these
VLANs being marked with 'BR_VLFLAG_ADDED_BY_SWITCHDEV'. This leads to
memory leaks [1] when the VLANs are deleted.
Fix by not calling the 8021q driver for VLANs that were already
programmed via switchdev.
[1]
unreferenced object 0xffff8881f6771200 (size 256):
comm "ip", pid 446855, jiffies 4298238841 (age 55.240s)
hex dump (first 32 bytes):
00 00 7f 0e 83 88 ff ff 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000012819ac>] vlan_vid_add+0x437/0x750
[<00000000f2281fad>] __br_vlan_set_proto+0x289/0x920
[<000000000632b56f>] br_changelink+0x3d6/0x13f0
[<0000000089d25f04>] __rtnl_newlink+0x8ae/0x14c0
[<00000000f6276baf>] rtnl_newlink+0x5f/0x90
[<00000000746dc902>] rtnetlink_rcv_msg+0x336/0xa00
[<000000001c2241c0>] netlink_rcv_skb+0x11d/0x340
[<0000000010588814>] netlink_unicast+0x438/0x710
[<00000000e1a4cd5c>] netlink_sendmsg+0x788/0xc40
[<00000000e8992d4e>] sock_sendmsg+0xb0/0xe0
[<00000000621b8f91>] ____sys_sendmsg+0x4ff/0x6d0
[<000000000ea26996>] ___sys_sendmsg+0x12e/0x1b0
[<00000000684f7e25>] __sys_sendmsg+0xab/0x130
[<000000004538b104>] do_syscall_64+0x3d/0x90
[<0000000091ed9678>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 279737939a ("net: bridge: Fix VLANs memory leak")
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20221114084509.860831-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Hao Lan says:
====================
net: hns3: This series bugfix for the HNS3 ethernet driver.
This series includes some bugfix for the HNS3 ethernet driver.
Patch 1# fix incorrect hw rss hash type of rx packet.
Fixes: 796640778c ("net: hns3: support RXD advanced layout")
Fixes: 232fc64b6e ("net: hns3: Add HW RSS hash information to RX skb")
Fixes: ea48586707 ("net: hns3: handle the BD info on the last BD of the packet")
Patch 2# fix return value check bug of rx copybreak.
Fixes: e74a726da2 ("net: hns3: refactor hns3_nic_reuse_page()")
Fixes: 99f6b5fb5f ("net: hns3: use bounce buffer when rx page can not be reused")
Patch 3# net: hns3: fix setting incorrect phy link ksettings
for firmware in resetting process
Fixes: f5f2b3e4dc ("net: hns3: add support for imp-controlled PHYs")
Fixes: c5ef83cbb1 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config")
Fixes: 2312e050f4 ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo")
====================
Link: https://lore.kernel.org/r/20221114082048.49450-1-lanhao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, if driver is in phy-imp(phy controlled by imp firmware) mode, as
driver did not update phy link ksettings after initialization process or
not update advertising when getting phy link ksettings from firmware, it
may set incorrect phy link ksettings for firmware in resetting process.
So fix it.
Fixes: f5f2b3e4dc ("net: hns3: add support for imp-controlled PHYs")
Fixes: c5ef83cbb1 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config")
Fixes: 2312e050f4 ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The refactoring of rx copybreak modifies the original return logic, which
will make this feature unavailable. So this patch fixes the return logic of
rx copybreak.
Fixes: e74a726da2 ("net: hns3: refactor hns3_nic_reuse_page()")
Fixes: 99f6b5fb5f ("net: hns3: use bounce buffer when rx page can not be reused")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the HNS3 driver reports the rss hash type
of each packet based on the rss hash tuples set. It
always reports PKT_HASH_TYPE_L4, without checking the
type of current packet. It's incorrect.
Fixes it by reporting it base on the packet type.
Fixes: 796640778c ("net: hns3: support RXD advanced layout")
Fixes: 232fc64b6e ("net: hns3: Add HW RSS hash information to RX skb")
Fixes: ea48586707 ("net: hns3: handle the BD info on the last BD of the packet")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sleep time is added to ensure the phy to be ready after loopback
bit was set. This to prevent the phy loopback test from failing.
Fixes: 020a45aff1 ("net: phy: marvell: add Marvell specific PHY loopback")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Aminuddin Jamaluddin <aminuddin.jamaluddin@intel.com>
Link: https://lore.kernel.org/r/20221114065302.10625-1-aminuddin.jamaluddin@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ena_init() won't destroy workqueue created by
create_singlethread_workqueue() when pci_register_driver() failed.
Call destroy_workqueue() when pci_register_driver() failed to prevent the
resource leak.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20221114025659.124726-1-yuancan@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
sk->sk_receive_queue is protected by skb queue lock, but for KCM
sockets its RX path takes mux->rx_lock to protect more than just
skb queue. However, kcm_recvmsg() still only grabs the skb queue
lock, so race conditions still exist.
We can teach kcm_recvmsg() to grab mux->rx_lock too but this would
introduce a potential performance regression as struct kcm_mux can
be shared by multiple KCM sockets.
So we have to enforce skb queue lock in requeue_rx_msgs() and handle
skb peek case carefully in kcm_wait_data(). Fortunately,
skb_recv_datagram() already handles it nicely and is widely used by
other sockets, we can just switch to skb_recv_datagram() after
getting rid of the unnecessary sock lock in kcm_recvmsg() and
kcm_splice_read(). Side note: SOCK_DONE is not used by KCM sockets,
so it is safe to get rid of this check too.
I ran the original syzbot reproducer for 30 min without seeing any
issue.
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+278279efdd2730dd14bf@syzkaller.appspotmail.com
Reported-by: shaozhengchao <shaozhengchao@huawei.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20221114005119.597905-1-xiyou.wangcong@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This function is used for every packet, siphash_4u64 is noticeably faster
than using local buffer + siphash:
Before:
1.23% kpktgend_0 [kernel.vmlinux] [k] __siphash_unaligned
0.14% kpktgend_0 [nf_conntrack] [k] hash_conntrack_raw
After:
0.79% kpktgend_0 [kernel.vmlinux] [k] siphash_4u64
0.15% kpktgend_0 [nf_conntrack] [k] hash_conntrack_raw
In the pktgen test this gives about ~2.4% performance improvement.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Analogous to NFT_MSG_GETOBJ_RESET, but for rules: Reset stateful
expressions like counters or quotas. The latter two are the only
consumers, adjust their 'dump' callbacks to respect the parameter
introduced earlier.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a 'reset' flag just like with nft_object_ops::dump. This will be
useful to reset "anonymous stateful objects", e.g. simple rule counters.
No functional change intended.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The kernel test robot complains that in certain combinations
when building the Mediatek drivers as modules we lack some
debounce table symbols, so export them.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1ff91f9d2 ("pinctrl: mediatek: Fix EINT pins input debounce time configuration")
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of "0x01" use the HVM_PARAM_CALLBACK_TYPE_PCI_INTX define from
the interface header in get_callback_via().
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
The SYN flood message prints the listening port number, but with many
processes bound to the same port on different IPs, it's impossible to
tell which socket is the problem.
Add the listen IP address to the SYN flood message.
For IPv6 use "[IP]:port" as per RFC-5952 and to provide ease of
copy-paste to "ss" filters. For IPv4 use "IP:port" to match.
Each protcol's "any" address and a host address now look like:
Possible SYN flooding on port 0.0.0.0:9001.
Possible SYN flooding on port 127.0.0.1:9001.
Possible SYN flooding on port [::]:9001.
Possible SYN flooding on port [fc00::1]:9001.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/4fedab7ce54a389aeadbdc639f6b4f4988e9d2d7.1668386107.git.jamie.bainbridge@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A problem about ionic create debugfs failed is triggered with the
following log given:
[ 415.799514] debugfs: Directory 'ionic' with parent '/' already present!
The reason is that ionic_init_module() returns ionic_bus_register_driver()
directly without checking its return value, if ionic_bus_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ionic can never be created later.
ionic_init_module()
ionic_debugfs_create() # create debugfs directory
ionic_bus_register_driver()
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when ionic_bus_register_driver() returns error.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20221113092929.19161-1-yuancan@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Thomas Gleixner says:
====================
genirq/msi: Treewide cleanup of pointless linux/msi.h includes
While working on per device MSI domains I noticed that quite some files
include linux/msi.h just because.
The top level comment in the header file clearly says:
Regular device drivers have no business with any of these functions....
and actually none of the drivers needs anything from msi.h.
====================
Link: https://lore.kernel.org/r/20221113201935.776707081@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nothing in these files needs anything from linux/msi.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: oss-drivers@corigine.com
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nothing in these file needs anything from linux/msi.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FDB entries that perform VXLAN encapsulation with an IPv6 underlay hold
a reference on a resource - the KVDL entry where the IPv6 underlay
destination IP is stored. For that, the driver maintains two hash tables:
1. Maps IPv6 to KVDL index
2. Maps {MAC, FID index} to IPv6 address
When a FDB entry is removed, the second table is used to find the relevant
IPv6 address and the first table is used to remove the reference count and
free the index if is not used anymore.
In order for a packet to be forwarded to a single remote VTEP, FDB
entries need to be configured at both the bridge and VXLAN devices' FDB
tables. Both entries are squashed into one {MAC, VLAN/VNI} -> IP entry
in the hardware. Therefore, in case one entry is removed, the entry will
be removed from the hardware and the remaining entry will be unmarked
with 'offload' flag since it is not offloaded anymore.
For example, the two FDB entries should be added to allow packets to be
forwarded via vx10:
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff self static dst 2001:db8:5::1
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff master static vlan 10
When one entry will be removed, the second one will not be offloaded
anymore. When the first entry (in VXLAN FDB) will be removed / will not be
offloaded anymore, the two mappings in IPv6 hash tables will be removed.
In case that the second entry is removed before the first one, unexpected
warnings[1][2] will be shown in user space as a result of removing the
first entry. The issue is that not offloaded entry is removed, the driver
tries to search the relevant entries in the hash tables, does not find them
and therefore warns.
Do not handle removing of not offloaded VXLAN FDB entries, as they were
already removed when the offload flag was removed.
[1]:
WARNING: CPU: 1 PID: 239 at drivers/net/ethernet/mellanox/mlxsw/spectrum_nve.c:914 mlxsw_sp_nve_ipv6_addr_map_del+0x6b/0x80 [mlxsw_spectrum]
...
Hardware name: Mellanox Technologies Ltd. Mellanox switch/Mellanox switch, BIOS 4.6.5 05/21/2015
Workqueue: mlxsw_core_ordered mlxsw_sp_switchdev_vxlan_fdb_event_work [mlxsw_spectrum]
RIP: 0010:mlxsw_sp_nve_ipv6_addr_map_del+0x6b/0x80 [mlxsw_spectrum]
...
Call Trace:
<TASK>
mlxsw_sp_port_fdb_tunnel_uc_op+0x6cf/0x7b0 [mlxsw_spectrum]
mlxsw_sp_switchdev_vxlan_fdb_event_work+0x17c/0x420 [mlxsw_spectrum]
? finish_task_switch.isra.0+0x8c/0x290
process_one_work+0x1cd/0x390
worker_thread+0x48/0x3c0
? process_one_work+0x390/0x390
kthread+0xe0/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
[2]:
WARNING: CPU: 0 PID: 239 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3035 mlxsw_sp_ipv6_addr_put+0x142/0x220 [mlxsw_spectrum]
...
Hardware name: Mellanox Technologies Ltd. Mellanox switch/Mellanox switch, BIOS 4.6.5 05/21/2015
Workqueue: mlxsw_core_ordered mlxsw_sp_switchdev_vxlan_fdb_event_work [mlxsw_spectrum]
RIP: 0010:mlxsw_sp_ipv6_addr_put+0x142/0x220 [mlxsw_spectrum]
...
Call Trace:
<TASK>
? mlxsw_sp_port_fdb_tun_uc_op6_sfd_write+0x5c1/0x610 [mlxsw_spectrum]
mlxsw_sp_port_fdb_tunnel_uc_op+0x6ec/0x7b0 [mlxsw_spectrum]
mlxsw_sp_switchdev_vxlan_fdb_event_work+0x17c/0x420 [mlxsw_spectrum]
? finish_task_switch.isra.0+0x8c/0x290
process_one_work+0x1cd/0x390
worker_thread+0x48/0x3c0
? process_one_work+0x390/0x390
kthread+0xe0/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 0860c76416 ("mlxsw: spectrum_nve: Keep track of IPv6 addresses used by FDB entries")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/c186de8cbd28e3eb661e06f31f7f2f2dff30020f.1668184350.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If CONFIG_PTP_1588_CLOCK_OPTIONAL=m and CONFIG_RENESAS_ETHER_SWITCH=y,
the following build error happened:
aarch64-linux-ld: DWARF error: could not find abbrev number 60
drivers/net/ethernet/renesas/rswitch.o: in function `rswitch_get_ts_info':
rswitch.c:(.text+0x408): undefined reference to `ptp_clock_index'
aarch64-linux-ld: DWARF error: could not find abbrev number 1190123
drivers/net/ethernet/renesas/rcar_gen4_ptp.o: in function `rcar_gen4_ptp_register':
rcar_gen4_ptp.c:(.text+0x4dc): undefined reference to `ptp_clock_register'
aarch64-linux-ld: drivers/net/ethernet/renesas/rcar_gen4_ptp.o: in function `rcar_gen4_ptp_unregister':
rcar_gen4_ptp.c:(.text+0x584): undefined reference to `ptp_clock_unregister'
To fix the issue, add "depends on PTP_1588_CLOCK_OPTIONAL" into the
Kconfig.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6c6fa1a00a ("net: ethernet: renesas: rswitch: Add R-Car Gen4 gPTP support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221110012720.3552060-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fixes for potential container registration leak for drivers not
implementing a close callback, duplicate container de-registrations,
and a regression in support for bus reset on last device close from
a device set. (Anthony DeRossi)
-----BEGIN PGP SIGNATURE-----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=xuV+
-----END PGP SIGNATURE-----
Merge tag 'vfio-v6.1-rc6' of https://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Fixes for potential container registration leak for drivers not
implementing a close callback, duplicate container de-registrations,
and a regression in support for bus reset on last device close from
a device set (Anthony DeRossi)
* tag 'vfio-v6.1-rc6' of https://github.com/awilliam/linux-vfio:
vfio/pci: Check the device set open count on reset
vfio: Export the device set open count
vfio: Fix container device registration life cycle
* Placate "$VARIABLE is used uninitialized" warnings
* omap2: Add missing dependency on GPMC
* qcom: Handle ret from parse with codeword_fixup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmNyBYUACgkQJWrqGEe9
VoRoAQf/R0n6rzsehjzwRlX1c2q6tFrBE7b1SNYw7zpjr4LfV8yoym/L/YfXVh50
a4OjlPhT+3/IJcy59jztgHH2ILvZmfDEm8NpJbO1LLci+Wa9U7tQPYOHstMUOcSn
SCDsR852+Mt1bC7NrFWFOxuBKpleCrb+NujKuBERd3CeCULquFMpqZvFgNPou6UN
mVPYZFSpLH35sQcxOchkaFk+0ZZeN6R5ojhXOxpNIoYoeiJ5GevSbCgR0W5ODsHw
vePAId1iDV7jOdBFXpHeKQ8O1KcCFVO8oDpI/lB+QYksfo+p4JI8R0VsQq0qs4Uq
fpR5JCy20Uoi8yncET1LcLlKezHXGw==
=s730
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Placate "$VARIABLE is used uninitialized" warnings
- omap2: Add missing dependency on GPMC
- qcom: Handle ret from parse with codeword_fixup
* tag 'mtd/fixes-for-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: onenand: omap2: add dependency on GPMC
mtd: rawnand: placate "$VARIABLE is used uninitialized" warnings
mtd: rawnand: qcom: handle ret from parse with codeword_fixup
Introduces new helper function to aid in .probe_new() refactors. In order
to use existing i2c_get_device_id() on the probe callback, the device
match table needs to be accessible in that function, which would require
bigger refactors in some drivers using the deprecated .probe callback.
This issue was discussed in more detail in the IIO mailing list.
Link: https://lore.kernel.org/all/20221023132302.911644-11-u.kleine-koenig@pengutronix.de/
Suggested-by: Nuno Sá <noname.nuno@gmail.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
