Jonas Bonn says:
====================
There's ongoing work in this driver to provide support for IPv6, GRO,
GSO, and "collect metadata" mode operation. In order to facilitate this
work going forward, this short series accumulates already ACK:ed patches
that are ready for the next merge window.
All of these patches should be uncontroversial at this point, including
the first one in the series that reverts a recently added change to
introduce "collect metadata" mode. As that patch produces 'broken'
packets when common GTP headers are in place, it seems better to revert
it and rethink things a bit before inclusion.
====================
Link: https://lore.kernel.org/r/20210203070805.281321-1-jonas@norrbonn.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Based on work by Pravin Shelar.
Update appropriate stats when packet transmission isn't possible.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set the devtype to 'gtp' when setting up the link.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call to skb_dst_drop() is already done as part of udp_tunnel_xmit().
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Blindly assuming that packet transmission crosses namespaces results in
skb marks being lost in the single namespace case.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Querying link info for the GTP interface doesn't reveal in which "role" the
device is set to operate. Include this information in the info query
result.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The GTP link is brought up with a default MTU of zero. This can lead to
some rather unexpected behaviour for users who are more accustomed to
interfaces coming online with reasonable defaults.
This patch sets an initial MTU for the GTP link of 1500 less worst-case
tunnel overhead.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 9ab7e76aef.
This patch was committed without maintainer approval and despite a number
of unaddressed concerns from review. There are several issues that
impede the acceptance of this patch and that make a reversion of this
particular instance of these changes the best way forward:
i) the patch contains several logically separate changes that would be
better served as smaller patches (for review purposes)
ii) functionality like the handling of end markers has been introduced
without further explanation
iii) symmetry between the handling of GTPv0 and GTPv1 has been
unnecessarily broken
iv) the patchset produces 'broken' packets when extension headers are
included
v) there are no available userspace tools to allow for testing this
functionality
vi) there is an unaddressed Coverity report against the patch concering
memory leakage
vii) most importantly, the patch contains a large amount of superfluous
churn that impedes other ongoing work with this driver
This patch will be reworked into a series that aligns with other
ongoing work and facilitates review.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to sock:inet_sock_set_state tracepoint, expose sk_family to
distinguish AF_INET and AF_INET6 families.
The following tcp tracepoints are updated:
tcp:tcp_destroy_sock
tcp:tcp_rcv_space_adjust
tcp:tcp_retransmit_skb
tcp:tcp_send_reset
tcp:tcp_receive_reset
tcp:tcp_retransmit_synack
tcp:tcp_probe
Signed-off-by: Hariharan Ananthakrishnan <hari@netflix.com>
Signed-off-by: Brendan Gregg <bgregg@netflix.com>
Link: https://lore.kernel.org/r/20210129001210.344438-1-hari@netflix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, a percpu_counter with the default batch size (2*nr_cpus) is
used to record the total # of active sockets per protocol. This means
sk_sockets_allocated_read_positive() could be off by +/-2*(nr_cpus^2).
This under/over-estimation could lead to wrong memory suppression
conditions in __sk_raise_mem_allocated().
Fix this by using a more reasonable fixed batch size of 16.
See related commit cf86a086a1 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting") that addresses a similar issue.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20210202193408.1171634-1-weiwan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson says:
====================
Support setting lanes via ethtool
Some speeds can be achieved with different number of lanes. For example,
100Gbps can be achieved using two lanes of 50Gbps or four lanes of
25Gbps. This patchset adds a new selector that allows ethtool to
advertise link modes according to their number of lanes and also force a
specific number of lanes when autonegotiation is off.
Advertising all link modes with a speed of 100Gbps that use two lanes:
$ ethtool -s swp1 speed 100000 lanes 2 autoneg on
Forcing a speed of 100Gbps using four lanes:
$ ethtool -s swp1 speed 100000 lanes 4 autoneg off
====================
Link: https://lore.kernel.org/r/20210202180612.325099-1-danieller@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that setting lanes parameter is working.
Set max speed and max lanes in the list of advertised link modes,
and then try to set max speed with the lanes below max lanes if exists
in the list.
And then, test that setting number of lanes larger than max lanes fails.
Do the above for both autoneg on and off.
$ ./ethtool_lanes.sh
TEST: 4 lanes is autonegotiated [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
TEST: Autoneg off, 4 lanes detected during force mode [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, pass the link mode bit in use.
In Spectrum-1, simply pass the bit that is set to '1' from PTYS register.
In Spectrum-2, pass the first link mode bit in the mask of the used
link mode.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when auto negotiation is set to off, the user can force a
specific speed or both speed and duplex. The user cannot influence the
number of lanes that will be forced.
Add support for setting speed along with lanes so one would be able
to choose how many lanes will be forced.
When lanes parameter is passed from user space, choose the link mode
that its actual width equals to it.
Otherwise, the default link mode will be the one that supports the width
of the port.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when a speed can be supported by different number of lanes,
the supported link modes bitmask contains only link modes with a single
number of lanes.
This was done in order to prevent auto negotiation on number of
lanes after 50G-1-lane and 100G-2-lanes link modes were introduced.
For example, if a port's max width is 4, only link modes with 4 lanes
will be presented as supported by that port, so 100G is always achieved by
4 lanes of 25G.
After the previous patches that allow selection of the number of lanes,
auto negotiation on number of lanes becomes practical.
Remove that filtering of the maximum number of lanes supported link modes,
so indeed all the supported and advertised link modes will be shown.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, ethtool does not expose how many lanes are used when the
link is up.
After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.
Extend ethtool to expose the number of lanes currently in use for
drivers that support it.
For example:
$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE Backplane ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
50000baseKR/Full
50000baseSR/Full
50000baseCR/Full
50000baseLR_ER_FR/Full
50000baseDR/Full
100000baseKR2/Full
100000baseSR2/Full
100000baseCR2/Full
100000baseLR2_ER2_FR2/Full
100000baseDR2/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Advertised link modes: 100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.
This would be a cleanup for next patch that would add another validation
to the new function.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bridge emits VLAN filtering events and quite a few others via
switchdev with orig_dev = br->dev. After the blamed commit, these events
started getting ignored.
The point of the patch was to not offload switchdev objects for ports
that didn't go through dsa_port_bridge_join, because the configuration
is unsupported:
- ports that offload a bonding/team interface go through
dsa_port_bridge_join when that bonding/team interface is later bridged
with another switch port or LAG
- ports that don't offload LAG don't get notified of the bridge that is
on top of that LAG.
Sadly, a check is missing, which is that the orig_dev is equal to the
bridge device. This check is compatible with the original intention,
because ports that don't offload bridging because they use a software
LAG don't have dp->bridge_dev set.
On a semi-related note, we should not offload switchdev objects or
populate dp->bridge_dev if the driver doesn't implement .port_bridge_join
either. However there is no regression associated with that, so it can
be done separately.
Fixes: 5696c8aedf ("net: dsa: Don't offload port attributes on standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20210202233109.1591466-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior says:
====================
chelsio: cxgb: Use threaded interrupts for deferred work
Patch #2 fixes an issue in which del_timer_sync() and tasklet_kill() is
invoked from the interrupt handler. This is probably a rare error case
since it disables interrupts / the card in that case.
Patch #1 converts a worker to use a threaded interrupt which is then
also used in patch #2 instead adding another worker for this task (and
flush_work() to synchronise vs rmmod).
====================
Link: https://lore.kernel.org/r/20210202170104.1909200-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
t1_fatal_err() is invoked from the interrupt handler. The bad part is
that it invokes (via t1_sge_stop()) del_timer_sync() and tasklet_kill().
Both functions must not be called from an interrupt because it is
possible that it will wait for the completion of the timer/tasklet it
just interrupted.
In case of a fatal error, use t1_interrupts_disable() to disable all
interrupt sources and then wake the interrupt thread with
F_PL_INTR_SGE_ERR as pending flag. The threaded-interrupt will stop the
card via t1_sge_stop() and not re-enable the interrupts again.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The external interrupt (F_PL_INTR_EXT) needs to be handled in a process
context and this is accomplished by utilizing a workqueue.
The process context can also be provided by a threaded interrupt instead
of a workqueue. The threaded interrupt can be used later for other
interrupt related processing which require non-atomic context without
using yet another workqueue. free_irq() also ensures that the thread is
done which is currently missing (the worker could continue after the
module has been removed).
Save pending flags in pending_thread_intr. Use the same mechanism
to disable F_PL_INTR_EXT as interrupt source like it is used before the
worker is scheduled. Enable the interrupt again once
t1_elmer0_ext_intr_handler() is done.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Srujana Challa says:
====================
Support for OcteonTX2 98xx CPT block.
OcteonTX2 series of silicons have multiple variants, the
98xx variant has two crypto (CPT) blocks to double the crypto
performance. This patchset adds support for new CPT block(CPT1).
====================
Link: https://lore.kernel.org/r/20210202152709.20450-1-schalla@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleans up all resources
attached to that VF. This patch adds support to handle
CPT FLR.
Signed-off-by: Narayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch changes CPT mailbox message format to
support new block CPT1 in 98xx silicon.
cpt_rd_wr_reg ->
Modify cpt_rd_wr_reg mailbox and its handler to
accommodate new block CPT1.
cpt_lf_alloc ->
Modify cpt_lf_alloc mailbox and its handler to
configure LFs from a block address out of multiple
blocks of same type. If a PF/VF needs to configure
LFs from both the blocks then this mbox should be
called twice.
Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mdio_bus reset code first de-asserted the reset by allocating with
GPIOD_OUT_LOW, then asserted and de-asserted again. In other words, if
the reset signal defaulted to asserted, there'd be a short "spike"
before the reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
We then fsleep() and finally set the GPIO low at point C.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found when we pulled down the reset signal for the
Marvell 88E1512P PHY (because it requires at least 50ms after POR with
an active clock). Looking at the reset signal with a scope revealed a
short spike, point B in the artwork above.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210202143239.10714-1-mike.looijmans@topic.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Probe should return an error code if platform_get_irq_byname() fails
but it returns success instead.
Fixes: 6c30384eb1 ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXyFIl4V9hgxYM@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are several error handling bugs in mscc_ocelot_init_ports(). I
went through the code, and carefully audited it and made fixes and
cleanups.
1) The ocelot_probe_port() function didn't have a mirror release function
so it was hard to follow. I created the ocelot_release_port()
function.
2) In the ocelot_probe_port() function, if the register_netdev() call
failed, then it lead to a double free_netdev(dev) bug. Fix this by
setting "ocelot->ports[port] = NULL" on the error path.
3) I was concerned that the "port" which comes from of_property_read_u32()
might be out of bounds so I added a check for that.
4) In the original code if ocelot_regmap_init() failed then the driver
tried to continue but I think that should be a fatal error.
5) If ocelot_probe_port() failed then the most recent devlink was leaked.
The fix for mostly came Vladimir Oltean. Get rid of "registered_ports"
and just set a bit in "devlink_ports_registered" to say when the
devlink port has been registered (and needs to be unregistered on
error). There are fewer than 32 ports so a u32 is large enough for
this purpose.
6) The error handling if the final ocelot_port_devlink_init() failed had
two problems. The "while (port-- >= 0)" loop should have been
"--port" pre-op instead of a post-op to avoid a buffer underflow.
The "if (!registered_ports[port])" condition was reversed leading to
resource leaks and double frees.
Fixes: 6c30384eb1 ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXhqRxHtRGzSnJ@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brian Vazquez says:
====================
net: use INDIRECT_CALL in some dst_ops
This patch series uses the INDIRECT_CALL wrappers in some dst_ops
functions to mitigate retpoline costs. Benefits depend on the
platform as described below.
Background: The kernel rewrites the retpoline code at
__x86_indirect_thunk_r11 depending on the CPU's requirements.
The INDIRECT_CALL wrappers provide hints on possible targets and
save the retpoline overhead using a direct call in case the
target matches one of the hints.
The retpoline overhead for the following three cases has been
measured by Luigi Rizzo in microbenchmarks, using CPU performance
counters, and cover reasonably well the range of possible retpoline
overheads compared to a plain indirect call (in equal conditions,
specifically with predicted branch, hot cache):
- just "jmp *(%r11)" on modern platforms like Intel Cascadelake.
In this case the overhead is just 2 clock cycles:
- "lfence; jmp *(%r11)" on e.g. some recent AMD CPUs.
In this case the lfence is blocked until pending reads complete,
so the actual overhead depends on previous instructions.
The best case we have measured 15 clock cycles of overhead.
- worst case, e.g. skylake, the full retpoline is used
__x86_indirect_thunk_r11: call set_u_target
capture_speculation: pause
lfence
jmp capture_speculation
.align 16
set_up_target: mov %r11, (%rsp)
ret
In this case the overhead has been measured in 35-40 clock cycles.
The actual time saved hence depends on the platform and current
clock speed (which varies heavily, especially when C-states are active).
Also note that actual benefit might be lower than expected if the
longer retpoline overlaps with some pending memory read.
MEASUREMENTS:
The INDIRECT_CALL wrappers in this patchset involve the processing
of incoming SYN and generation of syncookies. Hence, the test has been
run by configuring a receiving host with a single NIC rx queue, disabling
RPS and RFS so that all processing occurs on the same core.
An external source generates SYN fast enough to saturate the receiving CPU.
We ran two sets of experiments, with and without the dst_output patch,
comparing the number of syncookies generated over a 20s period
in multiple runs.
Assuming the CPU is saturated, the time per packet is
t = number_of_packets/total_time
and if the two datasets have statistically meaningful difference,
the difference in times between the two cases gives an estimate
of the benefits from one INDIRECT_CALL.
Here are the experimental results:
Skylake Syncookies over 20s (5 tests)
---------------------------------------------------
indirect 9166325 9182023 9170093 9134014 9171082
retpoline 9099308 9126350 9154841 9056377 9122376
Computing the stats on the ns_pkt = 20e6/total_packets gives the following:
$ ministat -c 95 -w 70 /tmp/sk-indirect /tmp/sk-retp
x /tmp/sk-indirect
+ /tmp/sk-retp
+----------------------------------------------------------------------+
|x xx x + x + + + +|
||______M__A_______|_|____________M_____A___________________| |
+----------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 5 2.17817e-06 2.18962e-06 2.181e-06 2.182292e-06 4.3252133e-09
+ 5 2.18464e-06 2.20839e-06 2.19241e-06 2.194974e-06 8.8695958e-09
Difference at 95.0% confidence
1.2682e-08 +/- 1.01766e-08
0.581132% +/- 0.466326%
(Student's t, pooled s = 6.97772e-09)
This suggests a difference of 13ns +/- 10ns
Our expectation from microbenchmarks was 35-40 cycles per call,
but part of the gains may be eaten by stalls from pending memory reads.
For Cascadelake:
Cascadelake Syncookies over 20s (5 tests)
---------------------------------------------------------
indirect 10339797 10297547 10366826 10378891 10384854
retpoline 10332674 10366805 10320374 10334272 10374087
Computing the stats on the ns_pkt = 20e6/total_packets gives no
meaningful difference even at just 80% (this was expected):
$ ministat -c 80 -w 70 /tmp/cl-indirect /tmp/cl-retp
x /tmp/cl-indirect
+ /tmp/cl-retp
+----------------------------------------------------------------------+
| x x + * x + + + x|
||______________|_M_________A_____A_______M________|___| |
+----------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 5 1.92588e-06 1.94221e-06 1.92923e-06 1.931716e-06 6.6936746e-09
+ 5 1.92788e-06 1.93791e-06 1.93531e-06 1.933188e-06 4.3734106e-09
No difference proven at 80.0% confidence
====================
Link: https://lore.kernel.org/r/20210201174132.3534118-1-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_dst_check and ipv4_dst_check
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_mtu and ipv4_mtu
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_output and ip_output
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip_local_deliver and ip6_input
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
inet_gro_receive() and inet_gro_complete() are part
of GRO engine which can not be modular.
Similarly, inet_gso_segment() does not need to be exported,
being part of GSO stack.
In other words, net/ipv6/ip6_offload.o is part of vmlinux,
regardless of CONFIG_IPV6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210202154145.1568451-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- cfg80211_dev_rename() requires RTNL
- cfg80211_change_iface() and cfg80211_set_encryption()
require wiphy mutex (was missing in wireless extensions)
- cfg80211_destroy_ifaces() requires wiphy mutex
- netdev registration can fail due to notifiers, and then
notifiers are "unrolled", need to handle this properly
-----BEGIN PGP SIGNATURE-----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=bgnR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time, only RTNL locking reduction fallout.
- cfg80211_dev_rename() requires RTNL
- cfg80211_change_iface() and cfg80211_set_encryption()
require wiphy mutex (was missing in wireless extensions)
- cfg80211_destroy_ifaces() requires wiphy mutex
- netdev registration can fail due to notifiers, and then
notifiers are "unrolled", need to handle this properly
* tag 'mac80211-next-for-net-next-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
cfg80211: fix netdev registration deadlock
cfg80211: call cfg80211_destroy_ifaces() with wiphy lock held
wext: call cfg80211_set_encryption() with wiphy lock held
wext: call cfg80211_change_iface() with wiphy lock held
nl80211: call cfg80211_dev_rename() under RTNL
====================
Link: https://lore.kernel.org/r/20210202144106.38207-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau says:
====================
mptcp: ADD_ADDR enhancements
This patch series from the MPTCP tree contains enhancements and
associated tests for the ADD_ADDR ("add address") MPTCP option. This
option allows already-connected MPTCP peers to share additional IP
addresses with each other, which can then be used to create additional
subflows within those MPTCP connections.
Patches 1 & 2 remove duplicated data in the per-connection path manager
structure.
Patches 3-6 initiate additional subflows when an address is added using
the netlink path manager interface and improve ADD_ADDR signaling
reliability, subject to configured limits. Self tests are also updated.
Patches 7-15 add new support for optional port numbers in ADD_ADDR. This
includes creating an additional in-kernel TCP listening socket for the
requested port number, validating the port number when processing
incoming subflow connections, including the port number in netlink
interfaces, and adding some new MIBs. New self test cases are added for
subflows connecting with alternate port numbers.
====================
Link: https://lore.kernel.org/r/20210201230920.66027-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds testcases for ADD_ADDR with port and the related MIB
counters check in chk_add_nr. The output looks like this:
24 signal address with port syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ] - pt [ ok ]
syn[ ok ] - synack[ ok ] - ack[ ok ]
syn[ ok ] - ack [ ok ]
25 subflow and signal with port syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ] - pt [ ok ]
syn[ ok ] - synack[ ok ] - ack[ ok ]
syn[ ok ] - ack [ ok ]
26 remove single address with port syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ] - pt [ ok ]
syn[ ok ] - synack[ ok ] - ack[ ok ]
syn[ ok ] - ack [ ok ]
rm [ ok ] - sf [ ok ]
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds the mibs for ADD_ADDR with port:
MPTCP_MIB_PORTADD for received ADD_ADDR suboption with a port number.
MPTCP_MIB_PORTSYNRX, MPTCP_MIB_PORTSYNACKRX, MPTCP_MIB_PORTACKRX, for
received MP_JOIN's SYN or SYN/ACK or ACK with a port number which is
different from the msk's port number.
MPTCP_MIB_MISMATCHPORTSYNRX and MPTCP_MIB_MISMATCHPORTACKRX, for
received SYN or ACK MP_JOIN with a mismatched port-number.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a new argument for pm_nl_ctl tool. We can use it like
this:
# pm_nl_ctl add 10.0.2.1 flags signal port 10100
# pm_nl_ctl dump
id 1 flags signal 10.0.2.1 10100
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds MPTCP_PM_ADDR_ATTR_PORT filling and parsing in PM
netlink.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When dealing with the addresses list local_addr_list or anno_list, we
should enable the function addresses_equal's parameter use_port. And
enable it in address_zero too.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds two new helpers, subflow_use_different_sport and
subflow_use_different_dport, to check whether the subflow's source or
destination port number is different from the msk's port number. When
receiving the MP_JOIN's SYN/SYNACK/ACK, we do these port number checks
and print out the different port numbers.
And furthermore, when receiving the MP_JOIN's SYN/ACK, we also use a new
helper mptcp_pm_sport_in_anno_list to check whether this port number is
announced. If it isn't, we need to abort this connection.
This patch also populates the local address's port field in
local_address.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a new helper named subflow_req_create_thmac, which is
extracted from subflow_token_join_request. It initializes subflow_req's
local_nonce and thmac fields, those are the more expensive to populate.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch drops the unused parameter skb in subflow_token_join_request.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch creates a listening socket when an address with a port-number
is added by PM netlink. Then binds the new port to the socket, and
listens for new connections.
When the address is removed or the addresses are flushed by PM netlink,
release the listening socket.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>