commit 44637ca41d upstream.
During lock arg validation, first check for -EBUSY cases, then for
-EINVAL cases. The -EINVAL checks look at lkb state variables
which are not stable when an lkb is busy and would cause an
-EBUSY result, e.g. lkb->lkb_grmode.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eef6ec9bf3 upstream.
This patch fixes a race by using ls_cb_mutex around the bit
operations and conditional code blocks for LSFL_CB_DELAY.
The function dlm_callback_stop() expects to stop all callbacks and
flush all currently queued onces. The set_bit() is not enough because
there can still be queue_work() after the workqueue was flushed.
To avoid queue_work() after set_bit(), surround both by ls_cb_mutex.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 301c8f5c32 upstream.
Commit c7b79a7528 ("mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI
IDs") caused a regression on certain Gigabyte motherboards for Intel
Alder Lake-S where system crashes to NULL pointer dereference in
i2c_dw_xfer_msg() when system resumes from S3 sleep state ("deep").
I was able to debug the issue on Gigabyte Z690 AORUS ELITE and made
following notes:
- Issue happens when resuming from S3 but not when resuming from
"s2idle"
- PCI device 00:15.0 == i2c_designware.0 is already in D0 state when
system enters into pci_pm_resume_noirq() while all other i2c_designware
PCI devices are in D3. Devices were runtime suspended and in D3 prior
entering into suspend
- Interrupt comes after pci_pm_resume_noirq() when device interrupts are
re-enabled
- According to register dump the interrupt really comes from the
i2c_designware.0. Controller is enabled, I2C target address register
points to a one detectable I2C device address 0x60 and the
DW_IC_RAW_INTR_STAT register START_DET, STOP_DET, ACTIVITY and
TX_EMPTY bits are set indicating completed I2C transaction.
My guess is that the firmware uses this controller to communicate with
an on-board I2C device during resume but does not disable the controller
before giving control to an operating system.
I was told the UEFI update fixes this but never the less it revealed the
driver is not ready to handle TX_EMPTY (or RX_FULL) interrupt when device
is supposed to be idle and state variables are not set (especially the
dev->msgs pointer which may point to NULL or stale old data).
Introduce a new software status flag STATUS_ACTIVE indicating when the
controller is active in driver point of view. Now treat all interrupts
that occur when is not set as unexpected and mask all interrupts from
the controller.
Fixes: c7b79a7528 ("mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI IDs")
Reported-by: Samuel Clark <slc2015@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215907
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e141772e6 upstream.
The Spreadtrum controller supports 100KHz minimal clock rate, which means
that the current value 400KHz is wrong.
Unfortunately this has also lead to fail to initialize some cards, which
are allowed to require 100KHz to work. So, let's fix the problem by
changing the minimal supported clock rate to 100KHz.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221011104935.10980-1-wenchao.chen666@gmail.com
[Ulf: Clarified to commit-message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0be1a655fe upstream.
can_restart() expects CMD_START_CHIP to set the error state to
ERROR_ACTIVE as it calls netif_carrier_on() immediately afterwards.
Otherwise the user may immediately trigger restart again and hit a
BUG_ON() in can_restart().
Fix kvaser_usb_leaf set_mode(CMD_START_CHIP) to set the expected state.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455561fb61 upstream.
The TX queue seems to be implicitly flushed by the hardware during
bus-off or bus-off recovery, but the driver does not reset the TX
bookkeeping.
Despite not resetting TX bookkeeping the driver still re-enables TX
queue unconditionally, leading to "cannot find free context" /
NETDEV_TX_BUSY errors if the TX queue was full at bus-off time.
Fix that by resetting TX bookkeeping on CAN restart.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1499ecaea9 upstream.
For command events read from the device,
kvaser_usb_leaf_read_bulk_callback() verifies that cmd->len does not
exceed the size of the received data, but the actual kvaser_cmd handlers
will happily read any kvaser_cmd fields without checking for cmd->len.
This can cause an overread if the last cmd in the buffer is shorter than
expected for the command type (with cmd->len showing the actual short
size).
Maximum overread seems to be 22 bytes (CMD_LEAF_LOG_MESSAGE), some of
which are delivered to userspace as-is.
Fix that by verifying the length of command before handling it.
This issue can only occur after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd7f30e174 upstream.
flush_comp is initialized when CMD_FLUSH_QUEUE is sent to the device and
completed when the device sends CMD_FLUSH_QUEUE_RESP.
This causes completion of uninitialized completion if the device sends
CMD_FLUSH_QUEUE_RESP before CMD_FLUSH_QUEUE is ever sent (e.g. as a
response to a flush by a previously bound driver, or a misbehaving
device).
Fix that by initializing flush_comp in kvaser_usb_init_one() like the
other completions.
This issue is only triggerable after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37d49519b4 upstream.
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
These hubs suffer from two separate problems:
1) After the host system was suspended and woken up, the hubs appear to
be in a random state. Some downstream ports (both internal to the
built-in audio and network controllers, and external to USB sockets)
may no longer be functional. The exact list of disabled ports (if
any) changes from wakeup to wakeup. Ports remain in that state until
the dock is power-cycled, or until the laptop is rebooted.
Wakeup sources connected to the hubs (keyboard, WoL on the integrated
gigabit controller) will wake the system up from suspend, but they
may no longer work after wakeup (and in that case will no longer work
as wakeup source in a subsequent suspend-wakeup cycle).
This issue appears in the logs with messages such as:
usb 1-6.1-port4: cannot disable (err = -71)
usb 1-6-port2: cannot disable (err = -71)
usb 1-6.1: clear tt 1 (80c0) error -71
usb 1-6-port4: cannot disable (err = -71)
usb 1-6.4: PM: dpm_run_callback(): usb_dev_resume+0x0/0x10 [usbcore] returns -71
usb 1-6.4: PM: failed to resume async: error -71
usb 1-7: reset full-speed USB device number 5 using xhci_hcd
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
2) Some USB devices cannot be enumerated properly. So far I have only
seen the issue with USB 3.0 devices. The same devices work without
problem directly connected to the host system, to other systems or to
other hubs (even when those hubs are connected to the OneLink+ dock).
One very reliable reproducer is this USB 3.0 HDD enclosure:
152d:9561 JMicron Technology Corp. / JMicron USA Technology Corp. Mobius
I have seen it happen sporadically with other USB 3.0 enclosures,
with controllers from different manufacturers, all self-powered.
Typical messages in the logs:
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 6, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 7, error -62
usb 2-1-port4: attempt power cycle
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 8, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 9, error -62
usb 2-1-port4: unable to enumerate USB device
Through trial and error, I found that the USB_QUIRK_RESET_RESUME solved
the second issue. Further testing then uncovered the first issue. Test
results are summarized in this table:
=======================================================================================
Settings USB2 hotplug USB3 hotplug State after waking up
---------------------------------------------------------------------------------------
power/control=auto works fails broken
usbcore.autosuspend=-1 works works broken
OR power/control=on
power/control=auto works (1) works (1) works
and USB_QUIRK_RESET_RESUME
power/control=on works works works
and USB_QUIRK_RESET_RESUME
HUB_QUIRK_DISABLE_AUTOSUSPEND works works works
and USB_QUIRK_RESET_RESUME
=======================================================================================
In those results, the power/control settings are applied to both hubs,
both on the USB2 and USB3 side, before each test.
From those results, USB_QUIRK_RESET_RESUME is required to reset the hubs
properly after a suspend-wakeup cycle, and the hubs must not autosuspend
to work around the USB3 issue.
A secondary effect of USB_QUIRK_RESET_RESUME is to prevent the hubs'
upstream links from suspending (the downstream ports can still suspend).
This secondary effect is used in results (1). It is enough to solve the
USB3 problem.
Setting USB_QUIRK_RESET_RESUME on those hubs is the smallest patch that
solves both issues.
Prior to creating this patch, I have used the USB_QUIRK_RESET_RESUME via
the kernel command line for over a year without noticing any side
effect.
Thanks to Oliver Neukum @Suse for explanations of the operations of
USB_QUIRK_RESET_RESUME, and requesting more testing.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220927073407.5672-1-jflf_kernel@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d591b32e51 upstream.
If DbC is already in use, then the allocated memory for the xhci_dbc struct
doesn't get freed before returning NULL, which leads to a memleak.
Fixes: 534675942e ("xhci: dbc: refactor xhci_dbc_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b4ab4abce upstream.
The DPS310 chip has been observed to get "stuck" such that pressure
and temperature measurements are never indicated as "ready" in the
MEAS_CFG register. The only solution is to reset the device and try
again. In order to avoid continual failures, use a boolean flag to
only try the reset after timeout once if errors persist.
Fixes: ba6ec48e76 ("iio: Add driver for Infineon DPS310")
Cc: <stable@vger.kernel.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220915195719.136812-3-eajames@linux.ibm.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2329717bd upstream.
Move the startup procedure into a function, and correct a missing
check on the return code for writing the PRS_CFG register.
Cc: <stable@vger.kernel.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220915195719.136812-2-eajames@linux.ibm.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4f43f01cf upstream.
Some of the supported devices have 4 or 2 LSB trailing bits that should
not be taken into account. Hence we need to shift these bits out which
fits perfectly on the scan type shift property. This change fixes both
raw and buffered reads.
Fixes: f2f7a44970 ("iio:adc:ad7923: Add support for the ad7904/ad7914/ad7924")
Fixes: 851644a60d ("iio: adc: ad7923: Add support for the ad7908/ad7918/ad7928")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220912081223.173584-2-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f4f1096d5 upstream.
After the result of the previous conversion is read the chip
automatically starts a new conversion and doesn't accept new i2c
transfers until this conversion is completed which makes the function
return failure.
So add an early return iff the programming of the new address isn't
needed. Note this will not fix the problem in general, but all cases
that are currently used. Once this changes we get the failure back, but
this can be addressed when the need arises.
Fixes: 69548b7c2c ("iio: adc: ltc2497: split protocol independent part in a separate module ")
Reported-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Denys Zagorui <dzagorui@cisco.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220815091647.1523532-1-dzagorui@cisco.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 558a25f903 upstream.
For reliable operation across the full range of supported
interface rates, the AD5593R needs a STOP condition between
address write, and data read (like show in the datasheet Figure 40)
so in turn i2c_smbus_read_word_swapped cannot be used.
While at it, a simple helper was added to make the code simpler.
Fixes: 56ca9db862 ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220913073413.140475-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e98ecc6e94 upstream.
Commit d5c7076b77 ("smb3: add smb3.1.1 to default dialect list")
extend the dialects from 3 to 4, but forget to decrease the extended
length when specific the dialect, then the message length is larger
than expected.
This maybe leak some info through network because not initialize the
message body.
After apply this patch, the VALIDATE_NEGOTIATE_INFO message length is
reduced from 28 bytes to 26 bytes.
Fixes: d5c7076b77 ("smb3: add smb3.1.1 to default dialect list")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Cc: <stable@vger.kernel.org>
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb44c31cdc upstream.
This is the opposite case of kernel bugzilla 216301.
If we mmap a file using cache=none and then proceed to update the mmapped
area these updates are not reflected in a later pread() of that part of the
file.
To fix this we must first destage any dirty pages in the range before
we allow the pread() to proceed.
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 365e1ececb upstream.
During vm boot, there might be possibility that vf registration
call comes before the vf association from host to vm.
And this might break netvsc vf path, To prevent the same block
vf registration until vf bind message comes from host.
Cc: stable@vger.kernel.org
Fixes: 00d7ddba11 ("hv_netvsc: pair VF based on serial number")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Gaurav Kohli <gauravkohli@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1161703c9b upstream.
Every dma_map_single() call should have its dma_unmap_single() counterpart,
because the DMA address space is a shared resource and one could render the
machine unusable by consuming all DMA addresses.
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Cc: stable@vger.kernel.org
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Alexander Dahl <ada@thorsis.com>
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220728074014.145406-1-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ea8e12978 upstream.
The ASUS ROG X16 (GV601R) series laptop has the same node-to-DAC pairs
as early models and the G14, this includes bass speakers which are by
default mapped incorrectly to the 0x06 node.
Add a quirk to use the same DAC pairs as the G14.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221010070347.36883-1-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66ba7c8850 upstream.
The initial fix for ASUS G533Z was based on faulty information. This
fixes the pincfg to values that have been verified with no existing
module options or other hacks enabled.
Enables headphone jack, and 5.1 surround.
[ corrected the indent level by tiwai ]
Fixes: bc2c23549c ("ALSA: hda/realtek: Add pincfg for ASUS G533Z HP jack")
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221010065702.35190-1-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 417b9c51f5 upstream.
After some feedback from users with Dell Precision 5530 machines, this
patch reverts the previous change to add ALC289_FIXUP_DUAL_SPK.
While it improved the speaker output quality, it caused the headphone
jack to have an audible "pop" sound when power saving was toggled.
Fixes: 1885ff13d4 ("ALSA: hda/realtek: Enable 4-speaker output Dell Precision 5530 laptop")
Signed-off-by: Callum Osmotherly <callum.osmotherly@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yz0uyN1zwZhnyRD6@piranha
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 568be8aaf8 upstream.
At an error path to release URB buffers and contexts, the driver might
hit a NULL dererence for u->urb pointer, when u->buffer_size has been
already set but the actual URB allocation failed.
Fix it by adding the NULL check of urb. Also, make sure that
buffer_size is cleared after the error path or the close.
Cc: <stable@vger.kernel.org>
Reported-by: Sabri N. Ferreiro <snferreiro1@gmail.com>
Link: https://lore.kernel.org/r/CAKG+3NRjTey+fFfUEGwuxL-pi_=T4cUskYG9OzpzHytF+tzYng@mail.gmail.com
Link: https://lore.kernel.org/r/20220930100129.19445-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6382da0828 upstream.
When the driver hits -ENOMEM at allocating a URB or a buffer, it
aborts and goes to the error path that releases the all previously
allocated resources. However, when -ENOMEM hits at the middle of the
sync EP URB allocation loop, the partially allocated URBs might be
left without released, because ep->nurbs is still zero at that point.
Fix it by setting ep->nurbs at first, so that the error handler loops
over the full URB list.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220930100151.19461-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97d917879d upstream.
We took sound_oss_mutex around the calls of unregister_sound_special()
at unregistering OSS devices. This may, however, lead to a deadlock,
because we manage the card release via the card's device object, and
the release may happen at unregister_sound_special() call -- which
will take sound_oss_mutex again in turn.
Although the deadlock might be fixed by relaxing the rawmidi mutex in
the previous commit, it's safer to move unregister_sound_special()
calls themselves out of the sound_oss_mutex, too. The call is
race-safe as the function has a spinlock protection by itself.
Link: https://lore.kernel.org/r/CAB7eexJP7w1B0mVgDF0dQ+gWor7UdkiwPczmL7pn91xx8xpzOA@mail.gmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221011070147.7611-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fd0a6e99b6.
Which was upstream commit 97ef77c52b.
The commit is missing dependencies and breaks NFS tests, remove it for
now.
Reported-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff05d4b45d
When we parse a multi-BSSID element, we might point some
element pointers into the allocated nontransmitted_profile.
However, we free this before returning, causing UAF when the
relevant pointers in the parsed elements are accessed.
Fix this by not allocating the scratch buffer separately but
as part of the returned structure instead, that way, there
are no lifetime issues with it.
The scratch buffer introduction as part of the returned data
here is taken from MLO feature work done by Ilan.
This fixes CVE-2022-42719.
Fixes: 5023b14cf4 ("mac80211: support profile split between elements")
Co-developed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8223ac199a upstream.
My previous commit 5d24828d05 ("mac80211: always allocate
struct ieee802_11_elems") had a few bugs and leaked the new
allocated struct in a few error cases, fix that.
Fixes: 5d24828d05 ("mac80211: always allocate struct ieee802_11_elems")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20211001211108.9839928e42e0.Ib81ca187d3d3af7ed1bfeac2e00d08a4637c8025@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the 802.11 spec evolves, we need to parse more and more
elements. This is causing the struct to grow, and we can no
longer get away with putting it on the stack.
Change the API to always dynamically allocate and return an
allocated pointer that must be kfree()d later.
As an alternative, I contemplated a scheme whereby we'd say
in the code which elements we needed, e.g.
DECLARE_ELEMENT_PARSER(elems,
SUPPORTED_CHANNELS,
CHANNEL_SWITCH,
EXT(KEY_DELIVERY));
ieee802_11_parse_elems(..., &elems, ...);
and while I think this is possible and will save us a lot
since most individual places only care about a small subset
of the elements, it ended up being a bit more work since a
lot of places do the parsing and then pass the struct to
other functions, sometimes with multiple levels.
Link: https://lore.kernel.org/r/20210920154009.26caff6b5998.I05ae58768e990e611aee8eca8abefd9d7bc15e05@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49a765d678 upstream.
There's no need to parse all elements etc. just to find the
authentication challenge - use cfg80211_find_elem() instead.
This also allows us to remove WLAN_EID_CHALLENGE handling
from the element parsing entirely.
Link: https://lore.kernel.org/r/20210920154009.45f9b3a15722.Ice3159ffad03a007d6154cbf1fb3a8c48489e86f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5b983c607 upstream.
We currently pass the entire elements to the rx_bcn_presp()
method, but only need mesh_config. Additionally, we use the
length of the elements to calculate back the entire frame's
length, but that's confusing - just pass the length of the
frame instead.
Link: https://lore.kernel.org/r/20210920154009.a18ed3d2da6c.I1824b773a0fbae4453e1433c184678ca14e8df45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e42deaac0 upstream.
Each transfer test functions have same parameter checking code. This patch
unites those to an introduced function.
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220907020100.122588-1-mie@igel.co.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17b984115 upstream.
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c90b93b5b7 upstream.
When updating beacon elements in a non-transmitted BSS,
also update the hidden sub-entries to the same beacon
elements, so that a future update through other paths
won't trigger a WARN_ON().
The warning is triggered because the beacon elements in
the hidden BSSes that are children of the BSS should
always be the same as in the parent.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2d03cabe2 upstream.
If beacon protection is active but the beacon cannot be
decrypted or is otherwise malformed, we call the cfg80211
API to report this to userspace, but that uses a netdev
pointer, which isn't present for P2P-Device. Fix this to
call it only conditionally to ensure cfg80211 won't crash
in the case of P2P-Device.
This fixes CVE-2022-42722.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 9eaf183af7 ("mac80211: Report beacon protection failures to user space")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1833b6f46d upstream.
If the tool on the other side (e.g. wmediumd) gets confused
about the rate, we hit a warning in mac80211. Silence that
by effectively duplicating the check here and dropping the
frame silently (in mac80211 it's dropped with the warning).
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcca852027 upstream.
If a non-transmitted BSS shares enough information (both
SSID and BSSID!) with another non-transmitted BSS of a
different AP, then we can find and update it, and then
try to add it to the non-transmitted BSS list. We do a
search for it on the transmitted BSS, but if it's not
there (but belongs to another transmitted BSS), the list
gets corrupted.
Since this is an erroneous situation, simply fail the
list insertion in this case and free the non-transmitted
BSS.
This fixes CVE-2022-42721.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b7808818c upstream.
There are multiple refcounting bugs related to multi-BSSID:
- In bss_ref_get(), if the BSS has a hidden_beacon_bss, then
the bss pointer is overwritten before checking for the
transmitted BSS, which is clearly wrong. Fix this by using
the bss_from_pub() macro.
- In cfg80211_bss_update() we copy the transmitted_bss pointer
from tmp into new, but then if we release new, we'll unref
it erroneously. We already set the pointer and ref it, but
need to NULL it since it was copied from the tmp data.
- In cfg80211_inform_single_bss_data(), if adding to the non-
transmitted list fails, we unlink the BSS and yet still we
return it, but this results in returning an entry without
a reference. We shouldn't return it anyway if it was broken
enough to not get added there.
This fixes CVE-2022-42720.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: a3584f56de ("cfg80211: Properly track transmitting and non-transmitting BSS")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 567e14e39e upstream.
When iterating the elements here, ensure the length byte is
present before checking it to see if the entire element will
fit into the buffer.
Longer term, we should rewrite this code using the type-safe
element iteration macros that check all of this.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f033d2bec upstream.
Per spec, the maximum value for the MaxBSSID ('n') indicator is 8,
and the minimum is 1 since a multiple BSSID set with just one BSSID
doesn't make sense (the # of BSSIDs is limited by 2^n).
Limit this in the parsing in both cfg80211 and mac80211, rejecting
any elements with an invalid value.
This fixes potentially bad shifts in the processing of these inside
the cfg80211_gen_new_bssid() function later.
I found this during the investigation of CVE-2022-41674 fixed by the
previous patch.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aebe9f4639 upstream.
In the copy code of the elements, we do the following calculation
to reach the end of the MBSSID element:
/* copy the IEs after MBSSID */
cpy_len = mbssid[1] + 2;
This looks fine, however, cpy_len is a u8, the same as mbssid[1],
so the addition of two can overflow. In this case the subsequent
memcpy() will overflow the allocated buffer, since it copies 256
bytes too much due to the way the allocation and memcpy() sizes
are calculated.
Fix this by using size_t for the cpy_len variable.
This fixes CVE-2022-41674.
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 748bc4dd9e upstream.
Previously, the fast pool was dumped into the main pool periodically in
the fast pool's hard IRQ handler. This worked fine and there weren't
problems with it, until RT came around. Since RT converts spinlocks into
sleeping locks, problems cropped up. Rather than switching to raw
spinlocks, the RT developers preferred we make the transformation from
originally doing:
do_some_stuff()
spin_lock()
do_some_other_stuff()
spin_unlock()
to doing:
do_some_stuff()
queue_work_on(some_other_stuff_worker)
This is an ordinary pattern done all over the kernel. However, Sherry
noticed a 10% performance regression in qperf TCP over a 40gbps
InfiniBand card. Quoting her message:
> MT27500 Family [ConnectX-3] cards:
> Infiniband device 'mlx4_0' port 1 status:
> default gid: fe80:0000:0000:0000:0010:e000:0178:9eb1
> base lid: 0x6
> sm lid: 0x1
> state: 4: ACTIVE
> phys state: 5: LinkUp
> rate: 40 Gb/sec (4X QDR)
> link_layer: InfiniBand
>
> Cards are configured with IP addresses on private subnet for IPoIB
> performance testing.
> Regression identified in this bug is in TCP latency in this stack as reported
> by qperf tcp_lat metric:
>
> We have one system listen as a qperf server:
> [root@yourQperfServer ~]# qperf
>
> Have the other system connect to qperf server as a client (in this
> case, it’s X7 server with Mellanox card):
> [root@yourQperfClient ~]# numactl -m0 -N0 qperf 20.20.20.101 -v -uu -ub --time 60 --wait_server 20 -oo msg_size:4K:1024K:*2 tcp_lat
Rather than incur the scheduling latency from queue_work_on, we can
instead switch to running on the next timer tick, on the same core. This
also batches things a bit more -- once per jiffy -- which is okay now
that mix_interrupt_randomness() can credit multiple bits at once.
Reported-by: Sherry Yang <sherry.yang@oracle.com>
Tested-by: Paul Webb <paul.x.webb@oracle.com>
Cc: Sherry Yang <sherry.yang@oracle.com>
Cc: Phillip Goerl <phillip.goerl@oracle.com>
Cc: Jack Vogel <jack.vogel@oracle.com>
Cc: Nicky Veitch <nicky.veitch@oracle.com>
Cc: Colm Harrington <colm.harrington@oracle.com>
Cc: Ramanan Govindarajan <ramanan.govindarajan@oracle.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Sultan Alsawaf <sultan@kerneltoast.com>
Cc: stable@vger.kernel.org
Fixes: 58340f8e95 ("random: defer fast pool mixing to worker")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ee0507e89 upstream.
In order to avoid reading and dirtying two cache lines on every IRQ,
move the work_struct to the bottom of the fast_pool struct. add_
interrupt_randomness() always touches .pool and .count, which are
currently split, because .mix pushes everything down. Instead, move .mix
to the bottom, so that .pool and .count are always in the first cache
line, since .mix is only accessed when the pool is full.
Fixes: 58340f8e95 ("random: defer fast pool mixing to worker")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
