[ Upstream commit 14e2976fba ]
The RPMh regulator driver is much newer and gets more attention, which in
consequence makes it do a few things better. Update qcom_smd-regulator's
probe function to mimic what rpmh-regulator does to address a couple of
issues:
- Probe defer now works correctly, before it used to, well,
kinda just die.. This fixes reliable probing on (at least) PM8994,
because Linux apparently cannot deal with supply map dependencies yet..
- Regulator data is now matched more sanely: regulator data is matched
against each individual regulator node name and throwing an -EINVAL if
data is missing, instead of just assuming everything is fine and
iterating over all subsequent array members.
- status = "disabled" will now work for disabling individual regulators in
DT. Previously it didn't seem to do much if anything at all.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20211230023442.1123424-1-konrad.dybcio@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b16bef60a9 upstream.
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 98e47570ba ]
In commit e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting
and setting the voltage"), all calls to get/set the voltage of the
control regulator were switched to unlocked versions to avoid deadlocks.
However, the call in the probe path is done without regulator locks
held. In this case the locked version should be used.
Switch back to the locked regulator_get_voltage() in the probe path to
avoid any mishaps.
Fixes: e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210825033704.3307263-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c73daee4b ]
Since config.dev = pdev->dev.parent in current code, so
dev_get_drvdata(rdev->dev.parent) call in hi6421_regulator_enable
returns the drvdata of the mfd device rather than the regulator. Fix it.
This was broken while converting to use simplified DT parsing because the
config.dev changed from pdev->dev to pdev->dev.parent for parsing the
parent's of_node.
Fixes: 29dc269a85 ("regulator: hi6421: Convert to use simplified DT parsing")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210630095959.2411543-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae60e6a9d2 ]
Use unsigned int instead of u32 for regmap_read/regmap_update_bits val
argument.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210619124133.4096683-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61eb1b24f9 ]
Current code sets config.driver_data to a zero initialized regulator
which is obviously wrong. Fix it.
Fixes: 4618119b9b ("regulator: hi655x: enable regulator for hi655x PMIC")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210620132715.60215-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a336dc8f68 ]
Use DIV_ROUND_UP to prevent truncation by integer division issue.
This ensures we return enough delay time.
Also fix returning negative value when new_sel < old_sel.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210618141412.4014912-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50c9462edc ]
The valid vsel value are 0 and 12, so the .vsel_mask should be 0xf.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/1624424169-510-1-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d019f38a1a ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620705198-104566-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f55c5dd11 upstream.
The MAX77620 driver fails to re-probe on deferred probe because driver
core tries to claim resources that are already claimed by the PINCTRL
device. Use device_set_of_node_from_dev() helper which marks OF node as
reused, skipping erroneous execution of pinctrl_bind_pins() for the PMIC
device on the re-probe.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210523224243.13219-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98e48cd928 upstream.
For the boot-on/always-on regulators the set_machine_constrainst() is
called before resolving rdev->supply. Thus the code would try to enable
rdev before enabling supplying regulator. Enforce resolving supply
regulator before enabling rdev.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210519221224.2868496-1-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b6e7088af ]
According to Table 30 ("DVFS_MoniVDAC [6:0] Setting Table") in the
BD9571MWV-M Datasheet Rev. 002, the valid voltage range is 600..1100 mV
(settings 0x3c..0x6e). While the lower limit is taken into account (by
setting regulator_desc.linear_min_sel to 0x3c), the upper limit is not.
Fix this by reducing regulator_desc.n_voltages from 0x80 to 0x6f.
Fixes: e85c5a153f ("regulator: Add ROHM BD9571MWV-M PMIC regulator driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210312130242.3390038-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20ccc362c3 ]
Use the correct name to avoid ldo7 commands being sent to ldo6's address.
Fixes: 06369bcc15 ("regulator: qcom-rpmh: Add support for SM8150")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210211034935.5622-1-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe954d8f1 ]
Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.
Commit ff268b56ce ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.
Commit c33d442328 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:
[ 26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!
There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.
Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.
Fixes: c33d442328 ("debugfs: make error message a bit more verbose")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5872bd339 ]
The device node reference obtained with of_get_child_by_name() should be
dropped on error paths.
Fixes: 26aec009f6 ("regulator: add device tree support for s5m8767")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121155914.48034-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dea6dd2ba6 ]
Call of_node_put() to drop references of regulators_np and reg_np before
returning error code.
Fixes: 9ae5cc75ce ("regulator: s5m8767: Pass descriptor instead of GPIO number")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121032756.49501-1-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e78bf6be7e ]
Decrements the reference count of device node and its child node.
Fixes: dfe7a1b058 ("regulator: AXP20x: Add support for regulators subsystem")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210120123313.107640-1-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14a71d509a ]
With commit eaa7995c52 (regulator: core: avoid
regulator_resolve_supply() race condition) we started holding the rdev
lock while resolving supplies, an operation that requires holding the
regulator_list_mutex. This results in lockdep warnings since in other
places we take the list mutex then the mutex on an individual rdev.
Since the goal is to make sure that we don't call set_supply() twice
rather than a concern about the cost of resolution pull the rdev lock
and check for duplicate resolution down to immediately before we do the
set_supply() and drop it again once the allocation is done.
Fixes: eaa7995c52 (regulator: core: avoid regulator_resolve_supply() race condition)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122132042.10306-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaa7995c52 ]
The final step in regulator_register() is to call
regulator_resolve_supply() for each registered regulator
(including the one in the process of being registered). The
regulator_resolve_supply() function first checks if rdev->supply
is NULL, then it performs various steps to try to find the supply.
If successful, rdev->supply is set inside of set_supply().
This procedure can encounter a race condition if two concurrent
tasks call regulator_register() near to each other on separate CPUs
and one of the regulators has rdev->supply_name specified. There
is currently nothing guaranteeing atomicity between the rdev->supply
check and set steps. Thus, both tasks can observe rdev->supply==NULL
in their regulator_resolve_supply() calls. This then results in
both creating a struct regulator for the supply. One ends up
actually stored in rdev->supply and the other is lost (though still
present in the supply's consumer_list).
Here is a kernel log snippet showing the issue:
[ 12.421768] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.425854] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.429064] debugfs: Directory 'regulator.4-SUPPLY' with parent
'17a00000.rsc:rpmh-regulator-gfxlvl-pm8350_s5_level'
already present!
Avoid this race condition by holding the rdev->mutex lock inside
of regulator_resolve_supply() while checking and setting
rdev->supply.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Link: https://lore.kernel.org/r/1610068562-4410-1-git-send-email-collinsd@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b66e4a8e5 ]
Use the typical startup times from the data sheet so boards get a
reasonable default. Not setting any enable time can lead to board hangs
when e.g. clocks are enabled too soon afterwards.
This fixes gpu power domain resume on the Librem 5.
[Moved #defines into driver, seems to be general agreement and avoids any
cross tree issues -- broonie]
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/41fb2ed19f584f138336344e2297ae7301f72b75.1608316658.git.agx@sigxcpu.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit df6b92fa40 upstream.
According to the datasheet pm8009's HFS515 regulators have 16mV
resolution rather than declared 1.6 mV. Correct the resolution.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 06369bcc15 ("regulator: qcom-rpmh: Add support for SM8150")
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201231122348.637917-3-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 291de1d102 upstream.
When I use the axp20x chip to power my SDIO device on the 5.4 kernel,
the output voltage of DLDO2 is wrong. After comparing the register
manual and source code of the chip, I found that the mask bit of the
driver register of the port was wrong. I fixed this error by modifying
the mask register of the source code. This error seems to be a copy
error of the macro when writing the code. Now the voltage output of
the DLDO2 port of axp20x is correct. My development environment is
Allwinner A40I of arm architecture, and the kernel version is 5.4.
Signed-off-by: DingHua Ma <dinghua.ma.sz@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org>
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Link: https://lore.kernel.org/r/20201201001000.22302-1-dinghua.ma.sz@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5c042b23f upstream.
Workaround regulators whose supply name happens to be the same as its
own name. This fixes boards that used to work before the early supply
resolving was removed. The error message is left in place so that
offending drivers can be detected.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/d703acde2a93100c3c7a81059d716c50ad1b1f52.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b639e254d upstream.
When a regulator's name equals its supply's name the
regulator_resolve_supply() recurses indefinitely. Add a check
so that debugging the problem is easier. The "fixed" commit
just exposed the problem.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/c6171057cfc0896f950c4d8cb82df0f9f1b89ad9.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57a6ad482a upstream.
Fixed commit introduced a possible second call to
set_machine_constraints() and that allocates memory for
rdev->constraints. Move the allocation to the caller so
it's easier to manage and done once.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/78c3d4016cebc08d441aad18cb924b4e4d9cf9df.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 365ec8b616 upstream.
Limit the fsl,pfuze-support-disable-sw to the pfuze100 and pfuze200
variants.
When enabling fsl,pfuze-support-disable-sw and using a pfuze3000 or
pfuze3001, the driver would choose pfuze100_sw_disable_regulator_ops
instead of the newly introduced and correct pfuze3000_sw_regulator_ops.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Fixes: 6f1cf5257a ("regualtor: pfuze100: correct sw1a/sw2 on pfuze3000")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201110174113.2066534-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ba546ebe0 ]
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efe ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cf1ad559a2 upstream.
regulator_get_voltage_rdev() is called in regulator probe() when
applying machine constraints. The "fixed" commit exposed the problem
that non-bypassed regulators can forward the request to its parent
(like bypassed ones) supply. Return -EPROBE_DEFER when the supply
is expected but not resolved yet.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-by: Ondřej Jirman <megous@megous.com>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Ondřej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/a9041d68b4d35e4a2dd71629c8a6422662acb5ee.1604351936.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aea6cb9970 ]
When creating a new regulator its supply cannot create the sysfs link
because the device is not yet published. Remove early supply resolving
since it will be done later anyway. This makes the following error
disappear and the symlinks get created instead.
DCDC_REG1: supplied by VSYS
VSYS: could not add device link regulator.3 err -2
Note: It doesn't fix the problem for bypassed regulators, though.
Fixes: 45389c4752 ("regulator: core: Add early supply resolution for regulators")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/ba09e0a8617ffeeb25cb4affffe6f3149319cef8.1601155770.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb5a79d2f ]
Currently we wrongly set the mask of value of LDO2/4 both to the mask of
LDO2, and the LDO4 voltage configuration is left untouched. This leads
to conflict when LDO2/4 are both in use.
Fix this issue by setting different vsel_mask to both regulators.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Link: https://lore.kernel.org/r/20200923005142.147135-1-icenowy@aosc.io
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59ae97a7a9 ]
If the zero duty cycle doesn't correspond to any voltage in the voltage
table, the PWM regulator returns an -EINVAL from get_voltage_sel() which
results in the core erroring out with a "failed to get the current
voltage" and ending up not applying the machine constraints.
Instead, return -ENOTRECOVERABLE which makes the core set the voltage
since it's at an unknown value.
For example, with this device tree:
fooregulator {
compatible = "pwm-regulator";
pwms = <&foopwm 0 100000>;
regulator-min-microvolt = <2250000>;
regulator-max-microvolt = <2250000>;
regulator-name = "fooregulator";
regulator-always-on;
regulator-boot-on;
voltage-table = <2250000 30>;
};
Before this patch:
fooregulator: failed to get the current voltage(-22)
After this patch:
fooregulator: Setting 2250000-2250000uV
fooregulator: 2250 mV
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20200902130952.24880-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0a7416f947 upstream.
The recent commit 7d8196641e ("regulator: Remove pointer table
overallocation") changed the size of coupled_rdevs and now KASAN is able
to detect slab-out-of-bounds problem in regulator_unlock_recursive(),
which is a legit problem caused by a typo in the code. The recursive
unlock function uses n_coupled value of a parent regulator for unlocking
supply regulator, while supply's n_coupled should be used. In practice
problem may only affect platforms that use coupled regulators.
Cc: stable@vger.kernel.org # 5.0+
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200831204335.19489-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3c731564e upstream.
By calling device_initialize() earlier and noting that kfree(NULL) is
ok, we can save a bit of code in error handling and plug of_node leak.
Fixed commit already did part of the work.
Fixes: 9177514ce3 ("regulator: fix memory leak on error path of regulator_register()")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/f5035b1b4d40745e66bacd571bbbb5e4644d21a1.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87fe29b61f upstream.
Move all allocations outside of the regulator_lock()ed section.
======================================================
WARNING: possible circular locking dependency detected
5.7.13+ #535 Not tainted
------------------------------------------------------
f2fs_discard-179:7/702 is trying to acquire lock:
c0e5d920 (regulator_list_mutex){+.+.}-{3:3}, at: regulator_lock_dependent+0x54/0x2c0
but task is already holding lock:
cb95b080 (&dcc->cmd_lock){+.+.}-{3:3}, at: __issue_discard_cmd+0xec/0x5f8
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
[...]
-> #3 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire.part.11+0x40/0x50
fs_reclaim_acquire+0x24/0x28
__kmalloc_track_caller+0x54/0x218
kstrdup+0x40/0x5c
create_regulator+0xf4/0x368
regulator_resolve_supply+0x1a0/0x200
regulator_register+0x9c8/0x163c
[...]
other info that might help us debug this:
Chain exists of:
regulator_list_mutex --> &sit_i->sentry_lock --> &dcc->cmd_lock
[...]
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/6eebc99b2474f4ffaa0405b15178ece0e7e4f608.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73a32129f8 upstream.
Allocating memory with regulator_list_mutex held makes lockdep unhappy
when memory pressure makes the system do fs_reclaim on eg. eMMC using
a regulator. Push the lock inside regulator_init_coupling() after the
allocation.
======================================================
WARNING: possible circular locking dependency detected
5.7.13+ #533 Not tainted
------------------------------------------------------
kswapd0/383 is trying to acquire lock:
cca78ca4 (&sbi->write_io[i][j].io_rwsem){++++}-{3:3}, at: __submit_merged_write_cond+0x104/0x154
but task is already holding lock:
c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire.part.11+0x40/0x50
fs_reclaim_acquire+0x24/0x28
__kmalloc+0x54/0x218
regulator_register+0x860/0x1584
dummy_regulator_probe+0x60/0xa8
[...]
other info that might help us debug this:
Chain exists of:
&sbi->write_io[i][j].io_rwsem --> regulator_list_mutex --> fs_reclaim
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
lock(regulator_list_mutex);
lock(fs_reclaim);
lock(&sbi->write_io[i][j].io_rwsem);
*** DEADLOCK ***
1 lock held by kswapd0/383:
#0: c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
[...]
Fixes: d8ca7d184b ("regulator: core: Introduce API for regulators coupling customization")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1a889cf7f61c6429c9e6b34ddcdde99be77a26b6.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a577f3456c ]
The code modifies rdev, but locks c_rdev instead. Remove the lock
as this is held together by regulator_list_mutex taken in the caller.
Fixes: f9503385b1 ("regulator: core: Mutually resolve regulators coupling")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/25eb81cefb37a646f3e44eaaf1d8ae8881cfde52.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 467bf30142 ]
Move another allocation out of regulator_list_mutex-protected region, as
reclaim might want to take the same lock.
WARNING: possible circular locking dependency detected
5.7.13+ #534 Not tainted
------------------------------------------------------
kswapd0/383 is trying to acquire lock:
c0e5d920 (regulator_list_mutex){+.+.}-{3:3}, at: regulator_lock_dependent+0x54/0x2c0
but task is already holding lock:
c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire.part.11+0x40/0x50
fs_reclaim_acquire+0x24/0x28
kmem_cache_alloc_trace+0x40/0x1e8
regulator_register+0x384/0x1630
devm_regulator_register+0x50/0x84
reg_fixed_voltage_probe+0x248/0x35c
[...]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
lock(regulator_list_mutex);
lock(fs_reclaim);
lock(regulator_list_mutex);
*** DEADLOCK ***
[...]
2 locks held by kswapd0/383:
#0: c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
#1: cb70e5e0 (hctx->srcu){....}-{0:0}, at: hctx_lock+0x60/0xb8
[...]
Fixes: 541d052d72 ("regulator: core: Only support passing enable GPIO descriptors")
[this commit only changes context]
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
[this is when the regulator_list_mutex was introduced in reclaim locking path]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/41fe6a9670335721b48e8f5195038c3d67a3bf92.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9177514ce3 ]
The change corrects registration and deregistration on error path
of a regulator, the problem was manifested by a reported memory
leak on deferred probe:
as3722-regulator as3722-regulator: regulator 13 register failed -517
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xecc43740 (size 64):
comm "swapper/0", pid 1, jiffies 4294937640 (age 712.880s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 2e 32 34 00 5a 5a 5a regulator.24.ZZZ
5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
backtrace:
[<0c4c3d1c>] __kmalloc_track_caller+0x15c/0x2c0
[<40c0ad48>] kvasprintf+0x64/0xd4
[<109abd29>] kvasprintf_const+0x70/0x84
[<c4215946>] kobject_set_name_vargs+0x34/0xa8
[<62282ea2>] dev_set_name+0x40/0x64
[<a39b6757>] regulator_register+0x3a4/0x1344
[<16a9543f>] devm_regulator_register+0x4c/0x84
[<51a4c6a1>] as3722_regulator_probe+0x294/0x754
...
The memory leak problem was introduced as a side ef another fix in
regulator_register() error path, I believe that the proper fix is
to decouple device_register() function into its two compounds and
initialize a struct device before assigning any values to its fields
and then using it before actual registration of a device happens.
This lets to call put_device() safely after initialization, and, since
now a release callback is called, kfree(rdev->constraints) shall be
removed to exclude a double free condition.
Fixes: a3cde9534e ("regulator: core: fix regulator_register() error paths to properly release rdev")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Wen Yang <wenyang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20200724005013.23278-1-vz@mleia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f1cf5257a ]
PFUZE100_SWB_REG is not proper for sw1a/sw2, because enable_mask/enable_reg
is not correct. On PFUZE3000, sw1a/sw2 should be the same as sw1a/sw2 on
pfuze100 except that voltages are not linear, so add new PFUZE3000_SW_REG
and pfuze3000_sw_regulator_ops which like the non-linear PFUZE100_SW_REG
and pfuze100_sw_regulator_ops.
Fixes: 1dced996ee ("regulator: pfuze100: update voltage setting for pfuze3000 sw1a")
Reported-by: Christophe Meynard <Christophe.Meynard@ign.fr>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592171648-8752-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02fbabd5f4 upstream.
There maybe an overshoot, when disabling, then re-enabling vrefbuf
too quickly. VREFBUF is used by ADC/DAC on some boards. When re-enabling
too quickly, an overshoot on the reference voltage make the conversions
inaccurate for a short period of time.
- Don't put the VREFBUF in HiZ when disabling, to force an active
discharge.
- Enforce a 1ms OFF/ON delay
Fixes: 0cdbf481e9 ("regulator: Add support for stm32-vrefbuf")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Message-Id: <1583312132-20932-1-git-send-email-fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d7610e8da ]
Change the exported symbols introduced by commit e915331149
("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
from EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL(), like is used for all the core
parts.
Fixes: e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200120123921.1204339-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e915331149 ]
`cat /sys/kernel/debug/regulator/regulator_summary` ends on a deadlock
when you have a voltage controlled regulator (vctrl).
The problem is that the vctrl_get_voltage() and vctrl_set_voltage() calls the
regulator_get_voltage() and regulator_set_voltage() and that will try to lock
again the dependent regulators (the regulator supplying the control voltage).
Fix the issue by exporting the unlocked version of the regulator_get_voltage()
and regulator_set_voltage() API so drivers that need it, like the voltage
controlled regulator driver can use it.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Reported-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200116094543.2847321-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8a039d377 ]
RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS
(Dynamic Voltage Scaling). These GPIOs are entirely optional but a
dev_warn() appeared when cleaning this driver to use a more up-to-date
gpiod API. At least reduce the log level to 'info' as it is totally
fine to not populate these GPIO on a hardware design.
This change is trivial but it is worth not polluting the logs during
bringup phase by having real warnings and errors sorted out
correctly.
Fixes: a13eaf02e2 ("regulator: rk808: make better use of the gpiod API")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b059b7e0ec upstream.
Add regulator_is_equal() helper to compare whether two regulators are
the same. This is useful for checking whether two separate regulators
in a driver are actually the same supply.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20191220164450.1395038-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55d5f62c3f ]
The bd70528 regulator driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell for
regulators is added.
Fixes: 99ea37bd1e ("regulator: bd70528: Support ROHM BD70528 regulator block")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20191023121452.GA1812@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
