Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All Allwinner A20 boards we support can only use either EMAC or GMAC,
as they share the same pins. As we have switched all supported to
GMAC, we should alias GMAC (the active controller) as ethernet0,
so u-boot will insert the MAC address for the correct controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CubieTruck uses the GMAC with an RGMII phy.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has EMAC and GMAC muxed on the same pins.
Add pin sets with gmac function for MII and RGMII mode to the DTSI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The module clocks in the A31 are still compatible with the A10 one. Add the SPI
module clocks and the PLL6 in the device tree to allow their use by the SPI
controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART2 is used on CubieTruck to connect to the Bluetooth module.
Add the pin set used in this case.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch will add a basic board support DT for the
LinkSprite pcDuino board.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull parisc updates from Helge Deller:
"The three major changes in this patchset is a implementation for
flexible userspace memory maps, cache-flushing fixes (again), and a
long-discussed ABI change to make EWOULDBLOCK the same value as
EAGAIN.
parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
to keep HP-UX compatibility. Since we will probably never implement
full HP-UX support, we prefer to drop this compatibility to make it
easier for us with Linux userspace programs which mostly never checked
for both values. We don't expect major fall-outs because of this
change, and if we face some, we will simply rebuild the necessary
applications in the debian archives"
* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: add flexible mmap memory layout support
parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
parisc: convert uapi/asm/stat.h to use native types only
parisc: wire up sched_setattr and sched_getattr
parisc: fix cache-flushing
parisc/sti_console: prefer Linux fonts over built-in ROM fonts
HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps. We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.
Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.
In the current implementation of the buffer cache, buffers are allocated
in the pagecache. That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space. So, we don't
need to allocate extra memory and copy the content of the buffers there.
This patch optimizes the code to avoid copying the buffers. It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs. This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.
New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.
This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>
On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>
The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: Helge Deller <deller@gmx.de>
This commit:
f8dae00684: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.
This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available. This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13
Pull SLAB changes from Pekka Enberg:
"Random bug fixes that have accumulated in my inbox over the past few
months"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: Fix warning on make htmldocs caused by slab.c
mm: slub: work around unneeded lockdep warning
mm: sl[uo]b: fix misleading comments
slub: Fix possible format string bug.
slub: use lockdep_assert_held
slub: Fix calculation of cpu slabs
slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings
Pull turbostat updates from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: introduce -s to dump counters
tools/power turbostat: remove unused command line option
turbostat: Add option to report joules consumed per sample
turbostat: run on HSX
turbostat: Add a .gitignore to ignore the compiled turbostat binary
turbostat: Clean up error handling; disambiguate error messages; use err and errx
turbostat: Factor out common function to open file and exit on failure
turbostat: Add a helper to parse a single int out of a file
turbostat: Check return value of fscanf
turbostat: Use GCC's CPUID functions to support PIC
turbostat: Don't attempt to printf an off_t with %zx
turbostat: Don't put unprocessed uapi headers in the include path
Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases coverage
of the multiplatform defconfig and some DTS changes that plumbs up some
of the devices that now have bindings and driver support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ymAC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
Similar to what was done for the lm75 driver.
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Based on an earlier attempt by Randy Dunlap.
Fix SENSORS_LM75 dependencies to eliminate build errors:
drivers/built-in.o: In function `lm75_remove':
lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `lm75_probe':
lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register'
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
The new option allows just run turbostat and get dump of counter values. It's
useful when we have something more than one program to test.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The -s is not used, let's remove it, and update quick help accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull misc kbuild changes from Michal Marek:
"The non-critical part of kbuild is small this time:
- Three fixes for make deb-pkg
- A new coccinelle check
One of the deb-pkg fixes is a leftover from the last merge window,
hence the merge commit"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
deb-pkg: Fix building for MIPS big-endian or ARM OABI
deb-pkg: Fix cross-building linux-headers package
scripts: Coccinelle script for pm_runtime_* return checks with IS_ERR_VALUE
deb-pkg: Inhibit initramfs builders if CONFIG_BLK_DEV_INITRD is not set
Both proc files are writeable and used for configuring cells. But
there is missing correct mode flag for writeable files. Without
this patch both proc files are read only.
[ It turns out they aren't really read-only, since root can write to
them even if the write bit isn't set due to CAP_DAC_OVERRIDE ]
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With commit d8d14bd09c ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.
However I missed that there was still a stale declaration in
arch/tile/.. which now causes a compile error on tile:
In file included from fs/dcookies.c:28:0:
include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'
Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged. The correct declaration is now in include/linux/compat.h
The build error was reported by Fenguang's build bot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs fixes from Steve French:
"A set of cifs fixes (mostly for symlinks, and SMB2 xattrs) and
cleanups"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix check for regular file in couldbe_mf_symlink()
[CIFS] Fix SMB2 mounts so they don't try to set or get xattrs via cifs
CIFS: Cleanup cifs open codepath
CIFS: Remove extra indentation in cifs_sfu_type
CIFS: Cleanup cifs_mknod
CIFS: Cleanup CIFSSMBOpen
cifs: Add support for follow_link on dfs shares under posix extensions
cifs: move unix extension call to cifs_query_symlink()
cifs: Re-order M-F Symlink code
cifs: Add create MFSymlinks to protocol ops struct
cifs: use protocol specific call for query_mf_symlink()
cifs: Rename MF symlink function names
cifs: Rename and cleanup open_query_close_cifs_symlink()
cifs: Fix memory leak in cifs_hardlink()
Pull vfs fixes from Al Viro:
"Several obvious fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix mountpoint reference leakage in linkat
hfsplus: use xattr handlers for removexattr
Typo in compat_sys_lseek() declaration
fs/super.c: sync ro remount after blocking writers
vfs: unexport the getname() symbol
Here's a single staging driver for a wireless chipset that has shown up
in the SteamBox hardware. It is merged separately from the "main"
staging pull request to sync up with the wireless api changes that came
in from the networking tree.
It's self-contained and works for me and others. Larry will be
replacing it with a "real" driver for 3.15, but for now this one is
needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLrs1oACgkQMUfUDdst+ymymgCdEAZh9GL3PyRDPCcefwYaOzo5
BZcAoLmtj9XGDxaA2d87y8bN+FyX28Ik
=l+1d
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull rtl8812ae staging wireless driver from Greg KH:
"Here's a single staging driver for a wireless chipset that has shown
up in the SteamBox hardware. It is merged separately from the "main"
staging pull request to sync up with the wireless api changes that
came in from the networking tree.
It's self-contained and works for me and others. Larry will be
replacing it with a "real" driver for 3.15, but for now this one is
needed"
* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8821ae: Enable build by reverting BROKEN marking
staging: r8821ae: Fix build problems
Staging: rtl8812ae: disable due to build errors
Staging: rtl8821ae: add TODO file
Staging: rtl8821ae: removed unused functions and variables
Staging: rtl8821ae: rc.c: fix up function prototypes
Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver
Revert commit ef83b0781a "PCI: Remove from bus_list and release
resources in pci_release_dev()" that made some nasty race conditions
become possible. For example, if a Thunderbolt link is unplugged
and then replugged immediately, the pci_release_dev() resulting from
the hot-remove code path may be racing with the hot-add code path
which after that commit causes various kinds of breakage to happen
(up to and including a hard crash of the whole system).
Moreover, the problem that commit ef83b0781a attempted to address
cannot happen any more after commit 8a4c5c329d "PCI: Check parent
kobject in pci_destroy_dev()", because pci_destroy_dev() will now
return immediately if it has already been executed for the given
device.
Note, however, that the invocation of msi_remove_pci_irq_vectors()
removed by commit ef83b0781a from pci_free_resources() along with
the other changes made by it is not added back because of subsequent
code changes depending on that modification.
Fixes: ef83b0781a (PCI: Remove from bus_list and release resources in pci_release_dev())
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.
The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>
Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels. Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
When an clock is specified in the device tree, enable it and use it to
determine the external clock frequency.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
