arch/mips/boot/dts/Makefile collects objects from sub-directories into
built-in.a only when CONFIG_BUILTIN_DTB is enabled. Reflect it also to
the sub-directory Makefiles. This suppresses unneeded built-in.a
creation in arch/mips/boot/dts/*/ directories.
While I am here, I replaced $(patsubst %.dtb, %.dtb.o, $(dtb-y)) with
$(addsuffix .o, $(dtb-y)) to simplify the code a little bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19099/
Signed-off-by: James Hogan <jhogan@kernel.org>
These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
Miscellaneous:
- Hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- Expand make help text for generic defconfigs
- Refactor handling of legacy defconfigs
- Determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- Introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- Constify gpio_led in Alchemy, AR7, and TXX9
- Silence a couple of W=1 warnings
- Remove duplicate includes
Platform support:
ath79:
- Fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- FIRMWARE: Use mac_pton() for MAC address parsing
- Add Luxul XAP1500/XWR1750 WiFi LEDs
- Use standard reset button for Luxul XWR-1750
BMIPS:
- Enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- Add STB PM, wake-up timer, watchdog DT nodes
Generic platform:
- Add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- Add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- Enable crc32-mips on r6 configs
Octeon:
- Drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688
-----BEGIN PGP SIGNATURE-----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=4vUc
-----END PGP SIGNATURE-----
Merge tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
More detailed summary:
Miscellaneous:
- hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- expand make help text for generic defconfigs
- refactor handling of legacy defconfigs
- determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- constify gpio_led in Alchemy, AR7, and TXX9
- silence a couple of W=1 warnings
- remove duplicate includes
Platform support:
Generic platform:
- add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- enable crc32-mips on r6 configs
ath79:
- fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- firmware: Use mac_pton() for MAC address parsing
- add Luxul XAP1500/XWR1750 WiFi LEDs
- use standard reset button for Luxul XWR-1750
BMIPS:
- enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- add STB PM, wake-up timer, watchdog DT nodes
Octeon:
- drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688"
* tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (37 commits)
MIPS: BCM47XX: Use standard reset button for Luxul XWR-1750
MIPS: BCM47XX: Add Luxul XAP1500/XWR1750 WiFi LEDs
MIPS: Make the default for PHYSICAL_START always 64-bit
MIPS: Use the entry point from the ELF file header
MAINTAINERS: Add entry for Microsemi MIPS SoCs
MIPS: generic: Add support for Microsemi Ocelot
MIPS: mscc: Add ocelot PCB123 device tree
MIPS: mscc: Add ocelot dtsi
dt-bindings: mips: Add bindings for Microsemi SoCs
dt-bindings: Add vendor prefix for Microsemi Corporation
MIPS: ath79: Fix AR724X_PLL_REG_PCIE_CONFIG offset
MIPS: pci-mt7620: Enable PCIe on MT7688
MIPS: pm-cps: Block system suspend when a JTAG probe is present
MIPS: VDSO: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: BPF: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: cpu-features.h: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: Introduce isa-rev.h to define MIPS_ISA_REV
MIPS: Hang more efficiently on halt/powerdown/restart
FIRMWARE: bcm47xx_nvram: Replace mac address parsing
MIPS: BMIPS: Add Broadcom STB watchdog nodes
...
Calling __stack_chk_guard_setup() in decompress_kernel() is too late
that stack checking always fails for decompress_kernel() itself. So
remove __stack_chk_guard_setup() and initialize __stack_chk_guard before
we call decompress_kernel().
Original code comes from ARM but also used for MIPS and SH, so fix them
together. If without this fix, compressed booting of these archs will
fail because stack checking is enabled by default (>=4.16).
Link: http://lkml.kernel.org/r/1522226933-29317-1-git-send-email-chenhc@lemote.com
Fixes: 8779657d29 ("stackprotector: Introduce CONFIG_CC_STACKPROTECTOR_STRONG")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Rich Felker <dalias@libc.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a device tree include file for the Microsemi Ocelot SoC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Allan Nielsen <Allan.Nielsen@microsemi.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18855/
Signed-off-by: James Hogan <jhogan@kernel.org>
The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.
The failure was:
Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
FATAL ERROR: Unable to parse input tree
/usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
/usr/bin/mkimage Can't add hashes to FIT blob
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 28128c61e0 ("kconfig.h: Include compiler types to avoid missed struct attributes")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The unit name was 8c00000 but since the reg property is declared as:
reg = <0x0 0x4c00000 0x1 0xfb400000>;
the unit name should have been instead 4c00000.
Tested on MIPS Creator CI20 (v1):
$ cat /sys/firmware/devicetree/.../partitions/partition@4c00000/label;echo
system
Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18529/
Signed-off-by: James Hogan <jhogan@kernel.org>
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were
resolved, namely setting unit-address to lower case, and adding a
whitespace before the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18528/
Signed-off-by: James Hogan <jhogan@kernel.org>
The GCW Zero (http://www.gcw-zero.com) is a retro-gaming focused
handheld game console, successfully kickstarted in ~2012, running Linux.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18490/
Signed-off-by: James Hogan <jhogan@kernel.org>
Provide just enough bits (clocks, clocksource, uart) to allow a kernel
to boot on the JZ4770 SoC to a initramfs userspace.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18487/
Signed-off-by: James Hogan <jhogan@kernel.org>
Make doesn't expand shell style "vmlinuz.{32,ecoff,bin,srec}" to the 4
separate files, so none of these files get cleaned up by make clean.
List the files separately instead.
Fixes: ec3352925b ("MIPS: Remove all generated vmlinuz* files on "make clean"")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18491/
These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default defconfig
instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
-----BEGIN PGP SIGNATURE-----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=xbL0
-----END PGP SIGNATURE-----
Merge tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default
defconfig instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks"
* tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (46 commits)
MIPS: Add iomem resource for kernel bss section.
MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
MIPS: BMIPS: Enable HARDIRQS_SW_RESEND
MIPS: pci: Make use of the BIT() macro inside the mt7620 driver
MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
MIPS: pci: Remove duplicate define in mt7620 driver
MIPS: ralink: Fix typo in mt7628 pinmux function
MIPS: ralink: Fix MT7628 pinmux
MIPS: Fix odd fp register warnings with MIPS64r2
watchdog: jz4780: Allow selection of jz4740-wdt driver
MIPS/ptrace: Update syscall nr on register changes
MIPS/ptrace: Pick up ptrace/seccomp changed syscalls
MIPS: Fix an n32 core file generation regset support regression
MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
MIPS: page.h: Define virt_to_pfn()
MIPS: Xilfpga: Switch to using generic defconfigs
MIPS: generic: Add support for MIPSfpga
MIPS: Set defconfig target to a generic system for 32r2el
MIPS: Kconfig: Set default MIPS system type as generic
MIPS: DTS: Remove num-slots from Pistachio SoC
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
arch/mips/boot/dts/brcm/bcm96358nb4ser.dts does not exist, so
we cannot build bcm96358nb4ser.dtb .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes: 695835511f ("MIPS: BMIPS: rename bcm96358nb4ser to bcm6358-neufbox4-sercom")
Cc: stable@vger.kernel.org # 4.9+
Acked-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add support for the MIPSfpga platform to generic kernel.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15846/
[jhogan@kernel.org: Use separate board-xilfpga.its.S. Add 32r2 and
little endian requires to board-xilfpga.config]
Signed-off-by: James Hogan <jhogan@kernel.org>
dwmmc driver deprecated num-slots and plan to get rid of it finally.
Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: James Hartley <james.hartley@sondrel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16741/
Signed-off-by: James Hogan <jhogan@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Most of DT files are compiled under arch/*/boot/dts/, but we have some
other directories, like drivers/of/unittest-data/. We often miss to
add gitignore patterns per directory. Since there are no source files
that end with .dtb or .dtb.S, we can ignore the patterns globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
While the current kernel code in drivers/of/ allows developers to be
sloppy and use the status value "ok", the current DTSpec 0.1 makes it
clear that the only officially proper spelling is "okay", so adjust
the very small number of DTS files under arch/mips/.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17227/
Signed-off-by: James Hogan <jhogan@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devicetree nodes for the DM9000 and the ethernet power regulator.
Additionally, add a new pinctrl node for the ethernet chip's pins.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for splitting arch/mips/generic/vmlinux.its.S into
multiple files such that it doesn't become a conflict magnet as boards
are added, allow platforms to specify a list of image tree source files
which will be concatenated to form the final source used to build the
image tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
Add support for the MIPS Boston development board to generic kernels,
which essentially amounts to:
- Adding the device tree source for the MIPS Boston board.
- Adding a Kconfig fragment which enables the appropriate drivers for
the MIPS Boston board.
With these changes in place generic kernels will support the board by
default, and kernels with only the drivers needed for Boston enabled can
be configured by setting BOARDS=boston during configuration. For
example:
$ make ARCH=mips 64r6el_defconfig BOARDS=boston
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16485/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building a FIT image we may want the kernel to build multiple .dtb
files, but we don't want to build them all into the kernel binary as
object files since they'll instead be included in the FIT image.
Commit daa10170da ("MIPS: DTS: img: add device tree for Marduk board")
however created arch/mips/boot/dts/img/Makefile with a line that builds
any enabled .dtb files into the kernel. Remove this & build the
pistachio object specifically, in preparation for adding .dtb targets
which we don't want to build into the kernel.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16484/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various interrupt specifiers in the device tree are not in a valid
format for the MIPS GIC interrupt controller binding. Where each
interrupt should provide 3 values - GIC_LOCAL or GIC_SHARED, the
pin number & the type of interrupt - the device tree was only providing
the pin number. This causes interrupts for those devices to not be used
when a GIC is present. SEAD-3 systems without a GIC are unaffected since
the DT fixup code generates interrupt specifiers that are valid for the
CPU interrupt controller.
Fix this by adding the GIC_SHARED & IRQ_TYPE_LEVEL_HIGH values to each
interrupt specifier.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: c11e3b48db ("MIPS: SEAD3: Probe UARTs using DT")
Fixes: a34e93882d ("MIPS: SEAD3: Probe ethernet controller using DT")
Fixes: 7afd2a5aec ("MIPS: SEAD3: Probe EHCI controller using DT")
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16189/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SEAD-3 board may be configured with or without a MIPS Global
Interrupt Controller (GIC). Because of this we have a device tree with a
default case of a GIC present, and code to fixup the device tree based
upon a configuration register that indicates the presence of the GIC.
In order to keep this DT fixup code simple, the interrupt-parent
property was specified at the root node of the SEAD-3 DT, allowing the
fixup code to simply change this property to the phandle of the CPU
interrupt controller if a GIC is not present & affect all
interrupt-using devices at once. This however causes a problem if we do
have a GIC & the device tree is used as-is, because the interrupt-parent
property of the root node applies to the CPU interrupt controller node.
This causes a cycle when of_irq_init() attempts to probe interrupt
controllers in order and boots fail due to a lack of configured
interrupts, with this message printed on the kernel console:
[ 0.000000] OF: of_irq_init: children remain, but no parents
Fix this by removing the interrupt-parent property from the DT root node
& instead setting it for each device which uses interrupts, ensuring
that the CPU interrupt controller node has no interrupt-parent &
allowing of_irq_init() to identify it as the root interrupt controller.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Keng Koh <keng.koh@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Name aliases in the SEAD-3 device tree serial0 & serial1, rather than
uart0 & uart1. This allows the core serial code to make use of the
aliases to ensure that the UARTs are consistently numbered as expected
rather than having the numbering depend upon probe order.
When translating YAMON-provided serial configuration to a device tree
stdout-path property adjust accordingly, such that we continue to
reference a valid alias.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SEAD-3 board doesn't & never has configured the GIC frequency.
Remove the timer node from the DT in order to avoid attempting to probe
the GIC clocksource/clockevent driver which will produce error messages
such as these during boot:
[ 0.000000] GIC frequency not specified.
[ 0.000000] Failed to initialize '/interrupt-controller@1b1c0000/timer': -22
[ 0.000000] clocksource_probe: no matching clocksources found
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16188/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The .its targets require information about the kernel binary, such as
its entry point, which is extracted from the vmlinux ELF. We therefore
require that the ELF is built before the .its files are generated.
Declare this requirement in the Makefile such that make will ensure this
is always the case, otherwise in corner cases we can hit issues as the
.its is generated with an incorrect (either invalid or stale) entry
point.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: cf2a5e0bb4 ("MIPS: Support generating Flattened Image Trees (.itb)")
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We set the pin configuration for the jz4780-nand and jz4780-uart
drivers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We set the pin configuration for the jz4740-nand, jz4740-mmc,
jz4740-fb, jz4740-pwm and jz4740-uart drivers.
This will permit those drivers to be cleaned out of the custom GPIO code
that they currently use.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For a description of the devicetree node, please read
Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
For a description of the gpio devicetree nodes, please read
Documentation/devicetree/bindings/gpio/ingenic,gpio.txt
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For a description of the pinctrl devicetree node, please read
Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
For a description of the gpio devicetree nodes, please read
Documentation/devicetree/bindings/gpio/ingenic,gpio.txt
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
An img directory exists for the Pistchio SoC device tree but the
directory itself isn't in the dts Makefile meaning the dtbs never get
built.
Fixes: daa10170da ("MIPS: DTS: img: add device tree for Marduk board")
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Reviewed-by: Rahul Bedarkar <Rahul.Bedarkar@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15309/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Al Viro noticed that we were using two different methods to filter out
flags from KBUILD_CFLAGS.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Add support for Imagination Technologies' Marduk board which is based
on Pistachio SoC. It is also known as Creator Ci40. Marduk is legacy
name and will be there for decades.
Documentation for this board can be found on
https://docs.creatordev.io/ci40/
This patch adds initial support for board with following peripherals:
* PWM based heartbeat LED
* GPIO based buttons
* SPI NOR flash on SPI1
* UART0 and UART1
* SD card
* Ethernet
* USB
* PWM
* ADC
* I2C
Signed-off-by: Rahul Bedarkar <rahul.bedarkar@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: James Hartley <james.hartley@imgtec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14394/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The make variables KBUILD_CFLAGS and KBUILD_AFLAGS both contain
$(LINUXINCLUDE). But the build already picks up $(LINUXINCLUDE) from
scripts/Makefile.lib. The net effect is that the (long) list of include
directories is used twice.
This is harmless but pointless. So stop using $(LINUXINCLUDE) twice.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14622/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
uzImage.bin is vmlinuz.bin wrapped in a legacy U-Boot image. Since
the extraction code is inside the image, it does not depend on the
boot loader to extract the kernel.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14473/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system power
controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only
-----BEGIN PGP SIGNATURE-----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=z4SX
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system
power controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only"
* tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (31 commits)
rtc: mcp795: Fix whitespace and indentation.
rtc: mcp795: Prefer using the BIT() macro.
rtc: mcp795: fix month write resetting date to 1.
rtc: mcp795: fix time range difference between linux and RTC chip.
rtc: mcp795: fix bitmask value for leap year (LP).
rtc: mcp795: use bcd2bin/bin2bcd.
rtc: add support for EPSON TOYOCOM RTC-7301SF/DG
rtc: ds1307: Add ACPI support
rtc: imxdi: (trivial) fix a typo
rtc: ds1374: Merge conditional + WARN_ON()
rtc: twl: make driver DT only
rtc: twl: kill static variables
rtc: fix typos in Kconfig
rtc: jz4740: make the driver builtin only
rtc: jz4740: remove unused EXPORT_SYMBOL
Documentation: bindings: fix twl-rtc documentation
rtc: Enable compile testing for Maxim and Samsung drivers
MIPS: jz4740: Remove obsolete code
MIPS: qi_lb60: Probe RTC driver from DT and use it as power controller
MIPS: jz4740: DTS: Probe the jz4740-rtc driver from devicetree
...
Since we already have a devicetree node for the jz4740-rtc driver, we
don't have to probe it from platform code.
Besides, using the jz4740-rtc driver as the power controller for the
qi_lb60 platform allows us to remove the jz4740 platform power-off code,
since this is the only jz4740-based board upstream.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that the jz4740-rtc driver supports devicetree, we can add a
devicetree node for it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 10b6ea0959 ("MIPS: Malta: Use syscon-reboot driver to reboot")
converted the Malta board to use the generic syscon-reboot driver to
handle reboots, but incorrectly used the value 0x4d rather than 0x42 as
the magic to write to the reboot register.
I also incorrectly believed that syscon/regmap would default to native
endianness, but this isn't the case. Force this by specifying with a
native-endian property in the devicetree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 10b6ea0959 ("MIPS: Malta: Use syscon-reboot driver to reboot")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-mips@linux-mips.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the MIPS SEAD-3 board support to be a generic board, supported
by generic kernels.
Because the SEAD-3 boot protocol was defined long ago and we don't want
to force a switch to the UHI protocol, SEAD-3 is added as a legacy board
which is detected by reading the REVISION register. This may technically
not be a valid memory read & future work will include attempting to
handle that gracefully. In practice since SEAD-3 is the only legacy
board supported by the generic kernel so far the read will only happen
on SEAD-3 boards, and even once Malta is converted the same REVISION
register exists there too. Other boards such as Boston, Ci20 & Ci40 will
use the UHI boot protocol & thus not run any of the legacy board detect
functions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce a "generic" platform, which aims to be board-agnostic by
making use of device trees passed by the boot protocol defined in the
MIPS UHI (Universal Hosting Interface) specification. Provision is made
for supporting boards which use a legacy boot protocol that can't be
changed, but adding support for such boards or any others is left to
followon patches.
Right now the built kernels expect to be loaded to 0x80100000, ie. in
kseg0. This is fine for the vast majority of MIPS platforms, but
nevertheless it would be good to remove this limitation in the future by
mapping the kernel via the TLB such that it can be loaded anywhere & map
itself appropriately.
Configuration is handled by dynamically generating configs using
scripts/kconfig/merge_config.sh, somewhat similar to the way powerpc
makes use of it. This allows for variations upon the configuration, eg.
differing architecture revisions or subsets of driver support for
differing boards, to be handled without having a large number of
defconfig files.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for generating kernel images in the Flattened Image Tree
(.itb) format as supported by U-Boot. This format is essentially a
Flattened Device Tree binary containing images (kernels, DTBs, ramdisks)
and configurations which link those images together. The big advantages
of FIT images over the uImage format are:
- We can include FDTs in the kernel image in a way that the bootloader
can extract it & manipulate it before providing it to the kernel.
Thus we can ship FDTs as part of the kernel giving us the advantages
of being able to develop & maintain the DT within the kernel tree,
but also have the benefits of the bootloader being able to
manipulate the FDT. Example uses for this would be to inject the
kernel command line into the chosen node, or to fill in the correct
memory size.
- We can include multiple configurations in a single kernel image.
This means that a single FIT image can, given appropriate
bootloaders, be booted on different boards with the bootloader
selecting an appropriate configuration & providing the correct FDT
to the kernel.
- We can support a multitude of hashes over the data.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the generic syscon-reboot driver to reboot the Malta board,
reducing the amount of platform code it requires.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Stephan Linz <linz@li-pro.net>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14279/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the DT nodes required to probe the CFI compatible parallel monitor
flash found on the Malta development board, and remove the platform
code that was previously doing it. Delete the now-empty malta-platform.c
file. Adjust the Malta defconfigs that enable MTD & the pflash/CFI
driver to enable CONFIG_MTD_PHYSMAP_OF rather than CONFIG_MTD_PHYSMAP in
order to preserve their behaviour.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14278/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the CPU, GIC & i8259 interrupt controllers present in the Malta
system using device tree. This enables interrupts to be provided to
devices using device tree as they are moved over to being probed using
it.
Since Malta is very configurable it's unknown whether a GIC will be
present at compile time. In order to support both cases the
malta_dt_shim code is added in order to detect whether a GIC is present,
adjusting the DT to route interrupts correctly and nop out the GIC node
if no GIC is found.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14274/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the img-ascii-lcd driver using device tree in order to display a
message on the SEAD3 board's LCD display, and remove the platform code
that was formerly performing this function. This removes more platform
code and moves SEAD3 further towards being entirely DT-based.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14063/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the custom platform code to restart when instructed to power off,
instead relying upon the generic restart-poweroff driver probed via DT
to do the same thing.
Remove also the halt implementation, which is incorrect. The generic
MIPS version will hang the system as halt should.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14057/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe a driver for the PLED & FLED LEDs found on the SEAD3 board using
the register-bit-led driver via device tree, rather than a custom driver
via platform code. Enable support for the register-bit-led driver & its
prerequisite syscon in sead3_defconfig.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the SEAD3 EHCI controller using the generic-ehci driver & device
tree rather than platform code, in order to reduce the amount of the
latter.
Now that no devices probed from platform code require interrupts, remove
the retrieval of the IRQ domain & sead3int.h.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14051/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the UARTs on SEAD3 boards using device tree rather than platform
code, in order to reduce the amount of the latter. This requires that
CONFIG_SERIAL_OF_PLATFORM be enabled, so enable it in sead3_defconfig.
The SEAD3 DT shim code is extended to read bootloader environment
variables to determine the appropriate UART & mode for kernel console
output & set the stdout-path property of the chosen node accordingly.
In contrast to the old platform code, which appears to have only ever
set "console=ttyS0,38400n8r" with the code in console_config never
having an effect, this will honor the "yamontty" environment variable to
select between the 2 UARTs on the board and then check the "modetty0" or
"modetty1" variable as appropriate to determine the UART configuration.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the CPU interrupt controller & optional Global Interrupt
Controller (GIC) using devicetree rather than platform code. Because the
bootloader on SEAD3 does not provide a device tree to the kernel & the
device tree is always built in, we patch out the GIC node during boot if
we detect that a GIC is not present in the system.
The appropriate IRQ domain is discovered by platform code setting up
device IRQ numbers temporarily. It will be removed by further patches
which move the devices towards being probed via device tree.
No behavioural change is intended by this patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When using clang as HOSTCC, the following warnings appear:
In file included from arch/mips/boot/tools/relocs_64.c:27:0:
arch/mips/boot/tools/relocs.c: In function ‘read_relocs’:
arch/mips/boot/tools/relocs.c:397:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
ELF_R_SYM(rel->r_info) = elf32_to_cpu(ELF_R_SYM(rel->r_info));
^~~~~~~~~
arch/mips/boot/tools/relocs.c:397:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
arch/mips/boot/tools/relocs.c: In function ‘walk_relocs’:
arch/mips/boot/tools/relocs.c:491:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Elf_Sym *sym = &sh_symtab[ELF_R_SYM(rel->r_info)];
^~~~~~~
arch/mips/boot/tools/relocs.c: In function ‘do_reloc’:
arch/mips/boot/tools/relocs.c:502:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
unsigned r_type = ELF_R_TYPE(rel->r_info);
^~~~~~~~
arch/mips/boot/tools/relocs.c: In function ‘do_reloc_info’:
arch/mips/boot/tools/relocs.c:641:3: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
rel_type(ELF_R_TYPE(rel->r_info)),
^~~~~~~~
Fix them by making Elf64_Mips_Rela a union
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Acked-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of rewriting the arguments, just move the appended dtb to where
the decompressed kernel expects it. This eliminates the need for special
casing vmlinuz.bin appended dtb files.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here is the quote from [1]:
The unit-address must match the first address specified
in the reg property of the node. If the node has no reg property,
the @ and unit-address must be omitted and the node-name alone
differentiates the node from other nodes at the same level
This patch adjusts MIPS dts-files and devicetree binding
documentation in accordance with [1].
[1] Power.org(tm) Standard for Embedded Power Architecture(tm)
Platform Requirements (ePAPR). Version 1.1 – 08 April 2011.
Chapter 2.2.1.1 Node Name Requirements
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13345/
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The DT fragment will select the ohci-platform driver, since that can
handle the JZ4740 OHCI just fine. While I don't have a JZ4740-based
board with anything connected to the USB host controller, I did test
the generic OHCI driver successfully on a JZ4770-based board.
The device is disabled by default; boards that want to use it can
override the "status" property. The mass-production Qi LB60 boards
don't use the USB host controller.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- now clock nodes definition is merged with core .dtsi file
- only one rootclk is now part of DT
- clock clients also updated based on new binding doc
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes wrong bcm7425 SATA AHCI hardware interrupt property value with
periph_intc and SATA PHY unit address, and removes needless
brcm,broken-{ncq,phy} properties what are not used anywhere.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13017/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This tool is based on the x86/boot/tools/relocs tool.
It parses the relocations present in the vmlinux elf file, building a
table of relocations that will be necessary to run the kernel from an
address other than its link address. This table is inserted into the
vmlinux elf, in the .data.relocs section. The table is subsequently used
by the code in arch/mips/kernel/relocate.c (added later) to relocate the
kernel.
The tool, by default, also marks all relocation sections as 0 length.
This is due to objcopy currently being unable to handle copying the
relocations between 64 and 32 bit elf files as is done when building a
64 bit kernel.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12981/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following features are supported:
* UART;
* SPI-flash;
* USB host;
* GPIO key and LED.
Please see https://onion.io/omega for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: L. D. Pinney <ldpinney@gmail.com>
Cc: Boken Lin <bl@onion.io>
Cc: Jacky Huang <huangfangcheng@163.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces devicetree for Atheros AR9331 SoC (AKA Hornet).
The AR9331 chip is a Wi-Fi System-On-Chip (WiSOC),
typically used in very cheap Access Points and Routers.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current ath79 clock.c code does not read reference clock and
pll setup from devicetree. E.g. you can set any clock rate value
in board DTS but it will have no effect on the real clk calculation.
This patch fixes some AR9132 devicetree clock support defects:
* clk initialization function ath79_clocks_init_dt_ng()
is introduced; it actually gets pll block base register
address and reference clock from devicetree;
* pll register parsing code is moved to the separate
ar724x_clk_init() function; this function
can be called from platform code or from devicetree code.
Also mips_hpt_frequency value is set from dt, so the appropriate
clock parameter is added to the cpu@0 devicetree node.
The same approach can be used for adding AR9331 devicetree support.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The include/dt-bindings/clock/ath79-clk.h header file
is introduced so we can use symbolic identifiers for SoC clocks.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here are some Sascha Hauer's arguments for using aliases in the dts
files:
- using aliases reduces the number of indentations in dts files;
- dts files become independent of the layout of the dtsi files
(it becomes possible to introduce another bus {} hierarchy between
a toplevel bus and the devices when you have to);
- less chances for typos. if &i2c2 does not exist you get an error.
If instead you duplicate the whole path in the dts file a typo
in the path will just create another node.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12873/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add DTS for EdgeRouter Lite that is usable as is without any "pruning"
with APPENDED_DTB.
Compared to builtin generic DTB, we can avoid errors and delays from
probing non-existent I2C devices.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add DTS for D-Link DSR-1000N that is usable as is without any "pruning"
with APPENDED_DTB. Split out the common parts from octeon_3xxx.dts
into octeon_3xxx.dtsi.
Compared to builtin generic DTB, we can specificy fixed links properly
and avoid probing non-existent I2C devices.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12840/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reuse the early printk code to support the serial in zboot. We copy
early_printk.c instead of referencing it because we need to build a
different object file for the normal kernel and zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12234/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that appended DTB is usable we can drop the builtin DTB support.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12231/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current ath79 clock.c code does not read reference clock and
pll setup from devicetree. The ar724x_clocks_init() function
recreates the clocks from scratch so devicetree clock
information is dropped. After adding the code which picked up
reference clock from devicetree I have found
that kernel does not boot anymore. The SPI and UART drivers
can't get clk; here are the bootlog error messages:
of_serial: probe of 18020000.uart failed with error -22
ath79-spi: probe of 1f000000.spi failed with error -22
The problem is that clock code assumes that reference clock
name is "ref" but current dts-file uses another name: "oscillator".
This patch fixes the problem by changing external oscillator
dt node name to "ref".
Please note that there is an alternative solution for the problem:
> --- a/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
> +++ b/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
> @@ -16,6 +16,7 @@
>
> extosc: oscillator {
> compatible = "fixed-clock";
> + clock-output-names = "ref";
> #clock-cells = <0>;
> clock-frequency = <40000000>;
> };
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The copied source files must be added to the extra-y list to have them
removed on clean.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12233/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some older GCC version (at least 4.6) emits calls to __bswapsi2() when
building the XZ decompressor. The link of the compressed image then
fails with the following error:
arch/mips/boot/compressed/decompress.o: In function '__fswab32':
include/uapi/linux/swab.h:60: undefined reference to '__bswapsi2'
Add bswapsi.o to the link to fix the build with these versions.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12232/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This has been a very busy release for regmap, not just in cleaning up
the mess we got ourselves into with the endianness handling but also in
other areas too:
- Fixes for the endianness handling so that we now explicltly default
to little endian (the code used to do this by accident). This
fixes handling of explictly specified endianness on big endian
systems.
- Optimisation of the implementation of register striding.
- A refectoring of the _update_bits() code to reduce duplication.
- Fixes and enhancements for the interrupt implementation which
make it easier to use in a wider range of systems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW5v4RAAoJECTWi3JdVIfQcP0H/R+22ZgPNo76YUHtnMi5zCiW
/TtUzcKg3QXMXpCxQx2p8shRg1eckjb2zeImDJKPteIsO9y04lrlO2ljVnio/Ut9
6uBGwmmcCa9/haL7waDrw5kQKmCjNAcXhAn7etsRcvpMaPdEwL71ZWfjCY3HtwyJ
zGoArFNveHzTeZKRNzGZemSA7r1TOLIkHNvS4yRD4H9K7bGfn1HWwumCgurTvpiB
nxuhpwO7GQy28fPQRfBlfg2TGI+B8GD+VV4qwWnGYR2pijyIE8Kxqawizxueq70f
YsjiRNepxgPSdWHGMdjcUwQVB2iOSh8LvObxuyW8oGZEFeUxC3JHUiJ79zkKGsg=
=PBtQ
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a very busy release for regmap, not just in cleaning up
the mess we got ourselves into with the endianness handling but also
in other areas too:
- Fixes for the endianness handling so that we now explicitly default
to little endian (the code used to do this by accident). This
fixes handling of explictly specified endianness on big endian
systems.
- Optimisation of the implementation of register striding.
- A refectoring of the _update_bits() code to reduce duplication.
- Fixes and enhancements for the interrupt implementation which make
it easier to use in a wider range of systems"
* tag 'regmap-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (28 commits)
regmap: irq: add devm apis for regmap_{add,del}_irq_chip
regmap: replace regmap_write_bits()
regmap: irq: Enable irq retriggering for nested irqs
regmap: add regmap_fields_force_xxx() macros
regmap: add regmap_field_force_xxx() macros
regmap: merge regmap_fields_update_bits() into macro
regmap: merge regmap_fields_write() into macro
regmap: add regmap_fields_update_bits_base()
regmap: merge regmap_field_update_bits() into macro
regmap: merge regmap_field_write() into macro
regmap: add regmap_field_update_bits_base()
regmap: merge regmap_update_bits_check_async() into macro
regmap: merge regmap_update_bits_check() into macro
regmap: merge regmap_update_bits_async() into macro
regmap: merge regmap_update_bits() into macro
regmap: add regmap_update_bits_base()
regcache: flat: Introduce register strider order
regcache: Introduce the index parsing API by stride order
regmap: core: Introduce register stride order
regmap: irq: add devm apis for regmap_{add,del}_irq_chip
...
Ingenic SoC declares ZBOOT support, but debug definitions are missing
for MACH_JZ4780 resulting in a build failure when DEBUG_ZBOOT is set.
The UART addresses are same as with JZ4740, so fix by covering JZ4780
with those as well.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12830/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 29bb45f25f (regmap-mmio: Use native endianness for read/write)
attempted to fix some long standing bugs in the MMIO implementation for
big endian systems caused by duplicate byte swapping in both regmap and
readl()/writel() which affected MIPS systems as when they are in big
endian mode they flip the endianness of all registers in the system, not
just the CPU. MIPS systems had worked around this by declaring regmap
using IPs as little endian which is inaccurate, unfortunately the issue
had not been reported.
Sadly the fix makes things worse rather than better. By changing the
behaviour to match the documentation it caused behaviour changes for
other IPs which broke them and by using the __raw I/O accessors to avoid
the endianness swapping in readl()/writel() it removed some memory
ordering guarantees and could potentially generate unvirtualisable
instructions on some architectures.
Unfortunately sorting out all this mess in any half way sensible fashion
was far too invasive to go in during an -rc cycle so instead let's go
back to the old broken behaviour for v4.5, the better fixes are already
queued for v4.6. This does mean that we keep the broken MIPS DTs for
another release but that seems the least bad way of handling the
situation.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
On many MIPS systems the endianness of IP blocks is kept the same as
that of the CPU by the hardware. This includes the system controllers
on these systems which are controlled via syscon which uses the regmap
API which used readl() and writel() to interact with the hardware,
meaning that all writes are converted to little endian when writing to
the hardware. This caused a bad interaction with the regmap core in big
endian mode since it was not aware of the byte swapping and so ended up
performing little endian writes.
Unfortunately when this issue was noticed it was addressed by updating
the DT for the affected devices to specify them as little endian. This
happened to work since it resulted in two endianness swaps which
cancelled each other out and gave little endian behaviour but meant that
the DT was clearly not accurately describing the hardware.
The intention of commit 29bb45f25f (regmap-mmio: Use native
endianness for read/write) was to fix this by making regmap default to
native endianness but this breaks most other MMIO users where the
hardware has a fixed endianness and the implementation uses the __raw
accessors which are not intended to be used outside of architecture
code. Instead use the newly added native-endian DT property to say
exactly what we want for these systems.
Fixes: 29bb45f25f (regmap-mmio: Use native endianness for read/write)
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds basic DTS configuration for the PIC32MZDA chip and in turn the
PIC32MZDA Starter Kit.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
and make use of them in the Ci20 device tree to add a node for the
board's NAND.
Note that since the pinctrl driver is not yet upstream, this includes
neither pin configuration nor busy/write-protect GPIO pins for the
NAND. Use of the NAND relies on the boot loader to have left the pins
configured in a usable state, which should be the case when booted
from the NAND.
[ralf@linux-mips.org: fold in Geert Uytterhoeven's patch and acks from
Harvey's latest version.]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mtd@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/11695/
Patchwork: https://patchwork.linux-mips.org/patch/11914/
Patchwork: https://patchwork.linux-mips.org/patch/11985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is 2 registers that is 8 bytes long, not 4.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alexander Couzens <lynxis@fe80.eu>
Cc: Joel Porquet <joel@porquet.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11508/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The regmap API has an endianness setting for formatting reads and writes.
This can be set by the usual DT "little-endian" and "big-endian" properties.
To work properly the associated regmap_bus needs to read/write in native
endian.
The "syscon" DT device binding creates an mmio-based regmap_bus which
performs all reads/writes as little-endian. These values are then converted
again by regmap, which means that all of the MIPS BCM boards (which are
big-endian) have been declared as "little-endian" to get regmap to convert
them back to big-endian.
Modify regmap-mmio to use the native-endian functions __raw_read*() and
__raw_write*() instead of the little-endian functions read*() and
write*().
Modify the big-endian MIPS BCM boards to use what will now be the correct
endianness instead of pretending that the devices are little-endian.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Move memory configuration to be performed via device tree for the Malta
board. This moves more Malta specific code to malta-dtshim.c, leaving
the rest of the mti-malta code a little more board-agnostic. This will
be useful to share more code between boards, with the device tree
providing the board specifics as intended.
Since we can't rely upon Malta boards running a bootloader capable of
handling devictrees & filling in the required information, a piece of
shim code (malta_dt_shim) is added to consume the (e)memsize variables
provided as part of the bootloader environment (or on the kernel command
line) then generate the DT memory node using the provided values.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Patchwork: https://patchwork.linux-mips.org/patch/11222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
When loading x86 64bit kernel above 4GiB with patched grub2, got kernel
gunzip error.
| early console in decompress_kernel
| decompress_kernel:
| input: [0x807f2143b4-0x807ff61aee]
| output: [0x807cc00000-0x807f3ea29b] 0x027ea29c: output_len
| boot via startup_64
| KASLR using RDTSC...
| new output: [0x46fe000000-0x470138cfff] 0x0338d000: output_run_size
| decompress: [0x46fe000000-0x47007ea29b] <=== [0x807f2143b4-0x807ff61aee]
|
| Decompressing Linux... gz...
|
| uncompression error
|
| -- System halted
the new buffer is at 0x46fe000000ULL, decompressor_gzip is using
0xffffffb901ffffff as out_len. gunzip in lib/zlib_inflate/inflate.c cap
that len to 0x01ffffff and decompress fails later.
We could hit this problem with crashkernel booting that uses kexec loading
kernel above 4GiB.
We have decompress_* support:
1. inbuf[]/outbuf[] for kernel preboot.
2. inbuf[]/flush() for initramfs
3. fill()/flush() for initrd.
This bug only affect kernel preboot path that use outbuf[].
Add __decompress and take real out_buf_len for gunzip instead of guessing
wrong buf size.
Fixes: 1431574a1c (lib/decompressors: fix "no limit" output buffer length)
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Jon Medhurst <tixy@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
The "LD vmlinuz" line in the quiet build output is misaligned with the
rest of the output. Fix this.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Build a DT for the Malta platform into the kernel, load it & probe
devices from it. The DT is essentially empty at this point, devices
will be added in further patches.
[ralf@linux-mips.org: Fixed conflicts.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/10119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Build all available dtbs to allow them to be appended to the resulting
kernel in case there is no builtin dtb.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hartley <James.Hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9740/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for detecting a vmlinuz.bin appended dtb and overriding
the boot arguments to match the UHI interface.
To ensure _edata / __apendend_dtb points to the actual end of the
binary, align the data section to 16 bytes instead of the address
cursor.
Due to ld.script not going through the preprocessor, we can't check
for MIPS_ZBOOT_APPENDED_DTB being enabled, so always reserve space
for it. It should have no consequences for booting without it enabled
except 1 MiB more ram usage during the uncompressing stage.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hartley <James.Hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9741/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a DTS for TL-WR1043ND version 1 and allow to have it built in the
kernel to circumvent the broken u-boot found on these boards.
Currently only the UART, LEDs and buttons are supported.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add two uart device nodes known as the uart1 and uart2 for the bcm7xxx
platforms.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9991/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a DTS file and Kconfig entry for the BCM97435SVMB evaluation board
using bcm7435.dtsi as an example.
The current code needs some tweaking to allow us to use the
dual-threaded dual BMIPS5200 CPUs, so for now we limit ourselves to
allowing just a single CPU to be booted.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: cernekee@chromium.org
Cc: Steven.Hill@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/9972/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support the Ingenic JZ4780 SoC using the existing code under
arch/mips/jz4740 now that it has been generalised sufficiently.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/10164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the serial support from arch/mips/jz4740 & make use of the new
Ingenic SoC UART driver. This is done for both regular & early console
output.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Apelete Seketeli <apelete@seketeli.net>
Cc: Alexandre Courbot <gnurou@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate the JZ4740 & the qi_lb60 board to use common clock framework
via the new Ingenic SoC CGU driver. Note that the JZ4740-specific
debugfs code is removed since common clock framework provides its own
debug capabilities.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Declare the JZ4740 interrupt controller for probe via DT using the
standard irqchip_init function, and make use of that function to probe
the controller by adding the appropriate node to the JZ4740 dtsi.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the generic irqchip_init function to probe irqchip drivers using DT,
and add the appropriate node to the JZ4740 devicetree in place of the
call to mips_cpu_irq_init.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Patchwork: https://patchwork.linux-mips.org/patch/10166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Require a DT for JZ4740 based systems, and add a stub one for the
qi_lb60 (Ben NanoNote) board. Devices will be migrated to being probed
via this DT over time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
!CONFIG_DEBUG_ZBOOT doesn't need puts() and puthex(), remove them and
the corrospindig strings for !CONFIG_DEBUG_ZBOOT, as a result, it saves
about 1280 bytes.
[ralf@linux-mips.org: Resolved reject.]
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1898/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DSR-1000N board has two GPIO LEDs next to USB ports. Add support for them.
[ralf@linux-mips.org: Resolved conflict due to the moving of the DTS files
into vendor subdirectories.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9624/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Platforms which use raw zboot images may need to link the image at
a fixed address if there is no other way to communicate the load
address to the bootloader. Allow the per-platform Kbuild files
to specify an optional zboot image load address (zload-y) and fall
back to calc_vmlinuz_load_addr if unset.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9566/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
Allow more compression algorithms as well as uncompressed uImage.bin
to be generated. An uncompressed image might be useful to rule out
problems in the decompression code in the bootloader or even speed
up the boot process at the expense of a bigger uImage file.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
HOSTCC arch/mips/boot/elf2ecoff
arch/mips/boot/elf2ecoff.c: In function ‘main’:
arch/mips/boot/elf2ecoff.c:271:8: warning: variable ‘shstrtab’ set but not used [-Wunused-but-set-variable]
char *shstrtab;
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These are generated by very recent toolchains and result in an error
message when attenpting to convert a kernel from ELF to ECOFF.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The if construct was getting hard to read and would be getting even more
complex with the next bug fix.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Ralink device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. A built-in device-tree is optional, so select
BUILTIN_DTB when it is requested.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7561/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Netlogic XLP device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. A built-in device-tree is optional, so select
BUILTIN_DTB when it is requested.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7560/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the SEAD-3 device-tree to arch/mips/boot/dts/ and update the
Makefiles accordingly. Since SEAD-3 requires the device-tree to be
built into the kernel, select BUILTIN_DTB when building for SEAD-3.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7555/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Lantiq device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. There is currently only a single Lantiq
device-tree (EASY50712), and it's required to be built into the kernel,
so select BUILTIN_DTB for it.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7559/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Octeon device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. Since Octeon requires the device-tree to be
built into the kernel, select BUILTIN_DTB as well.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7556/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a 'dtbs' Makefile target that just builds the device-tree binaries
enabled by the configuration.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7557/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for moving the device-trees to a common location,
introduce the config option BUILTIN_DTB, which can be selected by
platforms that use a device-tree built into the kernel image, and
create a Makefile to build the device-trees in arch/mips/boot/dts/.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7564/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit dc4d7b37 (MIPS: ZBOOT: gather string functions into string.c)
moved the string related functions into a separate file, which might
cause the following build error, depending on the configuration:
| CC arch/mips/boot/compressed/decompress.o
| In file included from linux/arch/mips/boot/compressed/../../../../lib/decompress_unxz.c:234:0,
| from linux/arch/mips/boot/compressed/decompress.c:67:
| linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'fill_temp':
| linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_stream.c:162:2: error: implicit declaration of function 'memcpy' [-Werror=implicit-function-declaration]
| cc1: some warnings being treated as errors
| linux/scripts/Makefile.build:308: recipe for target 'arch/mips/boot/compressed/decompress.o' failed
| make[6]: *** [arch/mips/boot/compressed/decompress.o] Error 1
| linux/arch/mips/Makefile:308: recipe for target 'vmlinuz' failed
It does not fail with the standard configuration, as when
CONFIG_DYNAMIC_DEBUG is not enabled <linux/string.h> gets included in
include/linux/dynamic_debug.h. There might be other ways for it to
get indirectly included.
We can't add the include directly in xz_dec_stream.c as some
architectures might want to use a different version for the boot/
directory (see for example arch/x86/boot/string.h).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7420/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch implements the stack protector code in MIPS compressed boot
phase based on the same code added to arm in commit
8779657d29 "stackprotector: Introduce
CONFIG_CC_STACKPROTECTOR_STRONG" by Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Chan <benchan@chromium.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Olof Johansson <olofj@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7175/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
In the worst case this adds less then 128 bytes of code
but on the other hand this makes code organization more clear.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6344/
Add support for the LZ4 compression scheme in the ZBOOT decompression
stub, in order to support it we need to:
- select the "lz4" compression tool to compress the vmlinux.bin
payload
- memcpy() is also required for decompress_unlz4.c so we share the
implementation between GZIP, XZ and now LZ4
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5829/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is currently no corresponding ELF program header for the "text"
loadable segment which is confusing for some bootloader out there such
as CFE because it expects to find a program header matching the segment
it is trying to load. The Linux kernel ELF binary "vmlinux" has a
similar program header for the text segment so we just mimic this here
too.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5827/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the XZ compression scheme in the ZBOOT decompression
stub, in order to support it we need to:
- select the "xzkern" compression tool to compress the vmlinux.bin
payload
- link with ashldi3.o for xz_dec_run() to work
- memcpy() is also required for decompress_unxz.c so we share the
implementation between GZIP and XZ
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5818/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a uImage build target for MIPS, which builds uImage.gz (a U-Boot
image of vmlinux.bin.gz), and then symlinks it to uImage. This allows
for the use of other compression algorithms in future, and is how a few
other architectures do it.
It's enabled conditionally on load-y >= 0xffffffff80000000 which
hopefully allows 64bit kernels to also work as long as the load and
entry address can be represented by the 32bit addresses in the U-Boot
image format.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5795/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The vmlinux load address and entry address is calculated in multiple
places:
- arch/mips/Makefile defines load-y from CONFIG_PHYSICAL_START (or
defined by the platform) and passes it to
arch/mips/boot/compressed/Makefile.
- arch/mips/boot/compressed/Makefile calculates kernel entry using nm.
- arch/mips/lasat/image/Makefile calculates both load and entry address
using nm.
Lets combine these in the main Makefile and then pass them as Make
parameters to each of the three boot image Makefiles (in boot/,
boot/compressed, lasat/image/). The boot/ Makefile doesn't currently use
them, but will soon need to for U-Boot image targets.
The existing load-y definition is used in preference to calculating the
load address using nm.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5794/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add symlink to include/dt-bindings from arch/mips/boot/dts/include/ to
match the ones in ARM and Meta architectures so that preprocessed device
tree files can include various useful constant definitions.
See commit c58299a (kbuild: create an "include chroot" for DT bindings)
merged in v3.10-rc1 for details.
MIPS structures it's dts files a little differently to other
architectures, having a separate dts directory for each SoC/platform,
but most of the definitions in the dt-bindings/ directory are common so
for now lets just have a single "include chroot" for all MIPS platforms.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Steven. J. Hill <steven.hill@imgtec.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kbuild@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Patchwork: http://patchwork.linux-mips.org/patch/5745/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building with -fstack-protector, gcc emits the __stack_chk_guard and
__stack_chk_fail symbols to check for stack stability. These symbols are
defined in vmlinux but the generated vmlinux.bin that is used to create
the compressed vmlinuz image has no symbol table so the linker can't find
these symbols during the final linking phase. As a result of which, we
need either to redefine these symbols just for the compressed image or drop
the -fstack-protector option when building the compressed image. This patch
implements the latter of two options.
Fixes the following linking problem:
dbg.c:(.text+0x7c): undefined reference to `__stack_chk_guard'
dbg.c:(.text+0x80): undefined reference to `__stack_chk_guard'
dbg.c:(.text+0xd4): undefined reference to `__stack_chk_guard'
dbg.c:(.text+0xec): undefined reference to `__stack_chk_fail'
[ralf@linux-mips.org: I'm applying this before the patch that actually adds
stack protector support for MIPS. This means, it will not be possible
to trigger above error message with any commit from the tree but rather
they are what one would hit without this commit.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/5575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add SYS_SUPPORTS_ZBOOT and SYS_SUPPORTS_ZBOOT_UART16550 config options
for XLR and XLP.
Update boot/compressed/uart-16550.c to add UART port for XLR and XLP.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5417/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Combine support for the DB1200/PB1200, DB1300 and DB1550 boards into
a single kernel image.
defconfig-generated image verified on DB1200, DB1300 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for building a compressed kernel for the JZ4740
architecture.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3563/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
HOSTCC arch/mips/boot/compressed/calc_vmlinuz_load_addr
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c: In function 'main':
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:35:2: warning: format '%llx' expects type 'long long unsigned int *', but argument 3 has type 'uint64_t *'
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:54:2: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'uint64_t'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Enable ISA_DMA_API config to fix build failure
MIPS: 32-bit: Fix build failure in asm/fcntl.h
MIPS: Remove all generated vmlinuz* files on "make clean"
MIPS: do_sigaltstack() expects userland pointers
MIPS: Fix error values in case of bad_stack
MIPS: Sanitize restart logics
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
MIPS: Don't block signals if we'd failed to setup a sigframe
[Ralf: I changed the patch to explicitly list all files to be deleted out
of paranoia.]
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1590/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix VMLINUZ_LOAD_ADDRESS calculation to be based on the length of
vmlinux.bin, the actual uncompressed kernel binary.
Previously it was based on the length of KBUILD_IMAGE (the unstripped ELF
vmlinux), which is bigger than vmlinux.bin. As a result, vmlinuz was
loaded into a memory address higher then actually needed - a problem for
small memory platforms.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
To: linux-mips@linux-mips.org
Cc: alex@digriz.org.uk
Cc: manuel.lauss@googlemail.com
Cc: sam@ravnborg.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1564/
Acked-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have calculated VMLINUZ_LOAD_ADDRESS in shell, which is indecipherable. This
patch rewrites it in C.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: linux-mips <linux-mips@linux-mips.org>
Cc: Alexander Clouter <alex@digriz.org.uk>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alexander Clouter <alex@digriz.org.uk>
Patchwork: https://patchwork.linux-mips.org/patch/1324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Remove several outdated comments
- Clearify the definition of zimage_start and zimage_size and the their
usage
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1382/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Remove unused symbols: _fdata, _text; only _edata and _end are needed by
head.S
- Remove unused sections: .sbss, .stab, .gptab.sdata, .gptab.sbss
- Change the alignment to 16 bytes to ensure it is greater than any
fundamental type of a MIPS compiler.
- Clean up comments
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The compressed vmlinux.bin is only a temp file so it's ok to use the same
suffix .z for them (.gz,.lzo,.lzma...) to remove several lines and simpify
the maintenance (no need to add the "suffix_$(xxx) := suffix" line).
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: linux-mips <linux-mips@linux-mips.org>
Cc: Alexander Clouter <alex@digriz.org.uk>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/1323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use hostprogs-y for the elf2ecoff
- list all *.o file in targets
- renamed obj-y to vmlinuzobjs-y (it was confusing to re-use a kbuild variable)
- fix all uses of if_changed/cmd
- use kbuild rules to beautify output
- update clean-file to clean vmlinuz.* in top-level directory
- simplied logic in arch/mips/Makefile for compressed targets
The net result is a more kbuild conformant Makefile but
readability did not increase.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1304/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- remove stuff that is not needed
VMLINUX assignment, all: rule
- use hostprogs-y for the host program
- use kbuild rules for the three targets - to beautify output
- drop clean-files - it is no longer needed
- simplify arch/mips/Makefile when calling targets in boot/Makefile
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1303/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a new DEBUG_ZBOOT option to allow the users to enable it
to debug the compressed kernel support for a new board and this optoin
should be disabled to reduce the kernel image size and speed up the
kernel booting procedure when the compressed kernel support is stable.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: Ralf Baechle <ralf@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/918/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hook up the compressed debug output for all Alchemy systems supported
by current kernel codebase.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/879/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
POSIX requires $((<expression>)) arithmetic in sh only to have long
arithmetic so on 32-bit sh binaries might do only 32-bit arithmetic but
the arithmetic done in arch/mips/boot/compressed/Makefile needs 64-bit.
I play with the AR7 platform, so VMLINUX_LOAD_ADDRESS is
0xffffffff94100000, and for an example 4MiB kernel
VMLINUZ_LOAD_ADDRESS is made out to be:
----
alex@berk:~$ bash -c 'printf "%x\n" $((0xffffffff94100000 + 0x400000))'
ffffffff94500000
alex@berk:~$ dash -c 'printf "%x\n" $((0xffffffff94100000 + 0x400000))'
80000000003fffff
----
The former is obviously correct whilst the later breaks things royally.
Fortunately working with only the lower 32bit's works for both bash and
dash:
----
$ bash -c 'printf "%x\n" $((0x94100000 + 0x400000))'
94500000
$ dash -c 'printf "%x\n" $((0x94100000 + 0x400000))'
94500000
----
So, we can split the original 64bit string to two parts, and only
calculate the low 32bit part, which is big enough (1GiB kernel sizes
anyone?) for a normal Linux kernel image file, now, we calculate the
VMLINUZ_LOAD_ADDRESS like this:
1. if present, append top 32bit of VMLINUX_LOAD_ADDRESS" as a prefix
2. get the sum of the low 32bit of VMLINUX_LOAD_ADDRESS + VMLINUX_SIZE
This patch fixes vmlinuz kernel builds on systems where only a
32bit-only math shell is available.
Patch Changelog:
Version 2
- simplified method by using 'expr' for 'substr' and making it work
with dash once again
Version 1
- Revert the removals of '-n "$(VMLINUX_SIZE)"' to avoid the error
of "make clean"
- Consider more cases of the VMLINUX_LOAD_ADDRESS
Version 0
- initial release
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/861/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Patchwork: http://patchwork.linux-mips.org/patch/857/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It moves to the same directory as the boot files in other formats.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/796/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Remove the .initrd section. The initrd section was already handled
when vmlinux was linked.
o Discard .MIPS.options, .options, .pdr, .reginfo, .comment and .note
sections. If .MIPS.options is not removed, kernels compiled with gcc
3.4.6 will not boot.
o Clean up the file format.
o Remove several other unneeded sections.
Tested with GCC 3.4.6 and 4.4.1 with and without initrd.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/785/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch helps to generate smaller kernel images for linux-MIPS,
Here is the effect when using lzma:
$ ls -sh vmlinux
7.1M vmlinux
$ ls -sh vmlinuz
1.5M vmlinuz
Have tested the 32bit kernel on Qemu/Malta and 64bit kernel on FuLoong
Mini PC. both of them work well. and also, tested by Alexander Clouter
on an AR7 based Linksys WAG54Gv2, and by Manuel Lauss on an Alchemy
board.
This -v2 version incorporate the feedback from Ralf, and add the
following changes:
1. add .ecoff, .bin, .erec format support
2. only enable it and the debug source code for the machines we tested
3. a dozen of fixups and cleanups
and if you want to enable it for your board, please try to select
SYS_SUPPORTS_ZBOOT for it, and if the board have an 16550 compatible
uart, you can select SYS_SUPPORTS_ZBOOT_UART16550 directly. and then
sending the relative patches to Ralf.
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
Tested-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Masahiro Yamada