- make the kconfig NAPI option prompt consistent across all net drivers
(other than EXPERIMENTAL; can it now be removed also, or is the new
napi_struct implementation now EXPERIMENTAL ?)
- remove comment about the now-deleted NAPI_HOWTO.txt file
- clean up typos in Tulip NAPI & Interrupt Mitigation
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Add a debugfs interface to look at internal ring state.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New version which uses less locking and drops old API
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With cleanup suggestions and bugs spotted by Stephen Hemminger,
Ingo Oeser, Matheos Worku, and Oliver Hartkopp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
this are the changes to the smc911x driver, which were necessary
to get it running on the Magic Panel R2 (smsc9115).
It is a SH3-DSP based board. The other patches are available on
the linuxsh-dev mailinglist.
http://marc.info/?l=linuxsh-dev&r=1&b=200708&w=2
It was necessary to set the irq sense to low level.
Therefor the SMC_IRQ_SENSE define was added.
How are the chances for inclusion in 2.6.24?
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hook up the 93cx6 eeprom code to the ax88796 driver and modify the ax88796
driver to read out the mac address from the eeprom. We need this for the
ax88796 on certain SuperH boards. The pin configuration used to connect
the eeprom to the ax88796 on these boards is the same as pointed out by the
ax88796 datasheet, so we can probably reuse this code for multiple
platforms in the future.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A driver model and phylib update. It includes the following changes:
1. Removal of unused module options.
2. Phylib support and the resulting removal of generic bits for handling
the PHY.
3. Proper reserving of device resources and using ioremap()ped handles
to access MAC registers rather than platform-specific macros.
4. Handling of the device using the driver model.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stop building and configuring driver for Digi RightSwitch, which was
never actually sold to anyone, and remove it from MAINTAINERS.
In response to an investigation into the firmware of the "Digi Rightswitch"
driver, Andres Salomon discovered:
>
> Dear Andres:
>
> After further research, we found that this product was killed in place
> and never reached the market. We would like to request that this not be
> included.
Since the product never reached market, clearly nobody is using this orphaned
driver.
Signed-off-by: Nathanael Nerode <neroden@gcc.gnu.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename NET_SB1250_MAC to SB1250_MAC to follow the convention.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SB1250 network interfaces are Gigabit Ethernet ones. Move the
Kconfig entry to the appropriate section and add some help text.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since we are adding requirement for the PHYLIB for this driver, there should be a select for that
Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually, D-Link modified the VendorID/ProductID of the TC902x.
The TC902x is the original chipset.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
This patch introduces support for dynamic reconfiguration (adding, removing
and/or modifying parameters of netconsole targets at runtime) using a
userspace interface exported via configfs. Documentation is also updated
accordingly.
Issues and brief design overview:
(1) Kernel-initiated creation / destruction of kernel objects is not
possible with configfs -- the lifetimes of the "config items" is managed
exclusively from userspace. But netconsole must support boot/module
params too, and these are parsed in kernel and hence netpolls must be
setup from the kernel. Joel Becker suggested to separately manage the
lifetimes of the two kinds of netconsole_target objects -- those created
via configfs mkdir(2) from userspace and those specified from the
boot/module option string. This adds complexity and some redundancy here
and also means that boot/module param-created targets are not exposed
through the configfs namespace (and hence cannot be updated / destroyed
dynamically). However, this saves us from locking / refcounting
complexities that would need to be introduced in configfs to support
kernel-initiated item creation / destroy there.
(2) In configfs, item creation takes place in the call chain of the
mkdir(2) syscall in the driver subsystem. If we used an ioctl(2) to
create / destroy objects from userspace, the special userspace program is
able to fill out the structure to be passed into the ioctl and hence
specify attributes such as local interface that are required at the time
we set up the netpoll. For configfs, this information is not available at
the time of mkdir(2). So, we keep all newly-created targets (via
configfs) disabled by default. The user is expected to set various
attributes appropriately (including the local network interface if
required) and then write(2) "1" to the "enabled" attribute. Thus,
netpoll_setup() is then called on the set parameters in the context of
_this_ write(2) on the "enabled" attribute itself. This design enables
the user to reconfigure existing netconsole targets at runtime to be
attached to newly-come-up interfaces that may not have existed when
netconsole was loaded or when the targets were actually created. All this
effectively enables us to get rid of custom ioctls.
(3) Ultra-paranoid configfs attribute show() and store() operations, with
sanity and input range checking, using only safe string primitives, and
compliant with the recommendations in Documentation/filesystems/sysfs.txt.
(4) A new function netpoll_print_options() is created in the netpoll API,
that just prints out the configured parameters for a netpoll structure.
netpoll_parse_options() is modified to use that and it is also exported to
be used from netconsole.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Keiichi Kii <k-keiichi@bx.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veth stands for Virtual ETHernet. It is a simple tunnel driver
that works at the link layer and looks like a pair of ethernet
devices interconnected with each other.
Mainly it allows to communicate between network namespaces but
it can be used as is as well.
The newlink callback is organized that way to make it easy to
create the peer device in the separate namespace when we have
them in kernel.
This implementation uses another interface - the RTM_NRELINK
message introduced by Patric.
Bug fixes from Daniel Lezcano.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1abecc489.
The driver works on some hardware that skge doesn't handle yet.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PPPOL2TP uses UDP so it obviously depends on CONFIG_INET.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling drivers from "Devices > Networking" (in menuconfig), for
example SLIP and/or PLIP, throws link time errors when CONFIG_NET itself
is =n. Have CONFIG_NETDEVICES depend on CONFIG_NET.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the driver necessary use the Analog Devices
Blackfin processor's on-chip ethernet MAC controller.
[try#2]
- add timeout control
- kill dma_config_reg bitfields
- some trivial cleanup
[try#3]
- add endianess check
- add DRV_NAME, DRV_VERSION... driver information string
- add some comments for silicon anomaly and dma API confusion
- some code trivial cleanup
[try#4]
- add Blackfin latest GPIO pin mux opertion with Michael Hennerich's
help and Dan's review
- rewrite the DMA descriptor list operation in a more readable way
by Joe's review
[try#5]
- cleanup some coding style by Joe's review.
[try#6]
- 1.1 version fix a bug when set up multicast list pointed by Mr. yoshfuji
- rearrange the desc_list_free function.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The network device frontend driver allows the kernel to access network
devices exported exported by a virtual machine containing a physical
network device driver.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Keir Fraser <Keir.Fraser@cl.cam.ac.uk>
Cc: netdev@vger.kernel.org
Convert the macb driver to use the generic PHY layer in
drivers/net/phy.
Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
splice: direct splicing updates ppos twice
more ACSI removal
umem: Fix match of pci_ids in umem driver
umem: Remove references to dead CONFIG_MM_MAP_MEMORY variable
remove the documentation for the legacy CDROM drivers
This patch removes some code that became dead code after the ATARI_ACSI
removal.
It also indirectly fixes the following bug introduced by
commit c2bcf3b897:
config ATARI_SLM
tristate "Atari SLM laser printer support"
- depends on ATARI && ATARI_ACSI!=n
+ depends on ATARI
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add macvlan driver, which allows to create virtual ethernet devices
based on MAC address.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the multiqueue hardware device support API to the core network
stack. Allow drivers to allocate multiple queues and manage them at
the netdev level if they choose to do so.
Added a new field to sk_buff, namely queue_mapping, for drivers to
know which tx_ring to select based on OS classification of the flow.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver handles only L2TP data frames; control frames are handled
by a userspace application. It implements L2TP using the PPPoX socket
family. There is a PPPoX socket for each L2TP session in an L2TP
tunnel. PPP data within each session is passed through the kernel's
PPP subsystem via this driver. Kernel parameters of each socket can be
read or modified using ioctl() or [gs]etsockopt() calls.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
bonding/bond_main.c: make 2 functions static
ps3: gigabit ethernet driver for PS3, take3
[netdrvr] Fix dependencies for ax88796 ne2k clone driver
eHEA: Capability flag for DLPAR support
Remove sk98lin ethernet driver.
sunhme.c:quattro_pci_find() must be __devinit
bonding / ipv6: no addrconf for slaves separately from master
atl1: remove write-only var in tx handler
macmace: use "unsigned long flags;"
Cleanup usbnet_probe() return value handling
netxen: deinline and sparse fix
eeprom_93cx6: shorten pulse timing to match spec (bis)
phylib: Add Marvell 88E1112 phy id
phylib: cleanup marvell.c a bit
AX88796 network driver
IOC3: Switch to pci refcounting safe APIs
e100: Fix Tyan motherboard e100 not receiving IPMI commands
QE Ethernet driver writes to wrong register to mask interrupts
rrunner.c:rr_init() must be __devinit
tokenring/3c359.c:xl_init() must be __devinit
...
Hi,
This is the third submission of the network driver for PS3.
The differences from the previous one are:
- renamed source file names so that their prefix can match
with the module name
- added cbe-oss-dev@ozlabs.org line for MAINTAINER file
- changed some in copyright comments
If there are no more comments, please apply for 2.6.23.
Thank you
--
Subject: PS3: Ethernet driver
From: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add Gigabit Ethernet support for the PS3 game console. The module will
be called ps3_gelic.
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an optional debug interface for displaying state of transmit/receive
rings. Creates a file debugfs/sky2/ethX for each device that is up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes to last version:
- spelling fix
- cleaned up probe code
Thomas.
Ethernet driver for EISA only SNI RM200/RM400 machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CONFIG_NETDEVICES, CONFIG_NET_ETHERNET:
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
CONFIG_SMC9194:
Move it so that it appears correctly in menuconfig.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The EMAC driver, in drivers/net/ibm_emac, for the embedded Ethernet
MAC found in PowerPC 4xx embedded chips is not suitable for
arch/powerpc. It will not build because it relies on the old arch/ppc
OCP mechanism. BenH has a new, device-tree aware version of the
driver which will work in arch/powerpc, but until it's merged, this
patch will disable the old, non-building version.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ucc_geth has been migrated to use the common phylib code. So lets add a
'select PHYLIB' to the UCC_GETH Kconfig entry.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hi,
This patch has removed unnecessary dependency on VIA velocity config.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The UCC_GETH Kconfig option in drivers/net/Kconfig had a line to select the
UCC_FAST option is arch/powerpc/sysdev/qe_lib/Kconfig, which is only used
on PowerPC builds. On other architectures, this would generated a warning.
The fix is to have UCC_FAST depend on UCC_GETH.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB/cm: Optimize stale connection detection
IB/mthca: Set cleaned CQEs back to HW ownership when cleaning CQ
IB/mthca: Fix posting >255 recv WRs for Tavor
RDMA/cma: Add check to validate that cm_id is bound to a device
RDMA/cma: Fix synchronization with device removal in cma_iw_handler
RDMA/cma: Simplify device removal handling code
IB/ehca: Disable scaling code by default, bump version number
IB/ehca: Beautify sysfs attribute code and fix compiler warnings
IB/ehca: Remove _irqsave, move #ifdef
IB/ehca: Fix AQP0/1 QP number
IB/ehca: Correctly set GRH mask bit in ehca_modify_qp()
IB/ehca: Serialize hypervisor calls in ehca_register_mr()
IB/ipath: Shadow the gpio_mask register
IB/mlx4: Fix uninitialized spinlock for 32-bit archs
mlx4_core: Remove unused doorbell_lock
net: Trivial MLX4_DEBUG dependency fix.
CONFIG_MLX4_DEBUG works out to a def_bool y for those that have
CONFIG_EMBEDDED set. Make it depend on MLX4_CORE.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
IB: Put rlimit accounting struct in struct ib_umem
IB/uverbs: Export ib_umem_get()/ib_umem_release() to modules
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer. Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch lets RBTX49XX boards use generic platform_driver interface
for the ne driver.
* Use platform_device to pass ioaddr and irq to the ne driver.
* Remove unnecessary ifdefs for RBTX49XX from the ne driver.
* Make the ne driver selectable on these boards regardless of CONFIG_ISA
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As SMC91X ethernet controller are used in blackfin STAMP 533 development
board, this patch add blackfin support to the smc91x linux driver.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
Fix a race condition in the transmit code, where the dma interrupt could update
the free tx buffer count concurrently and wedge the tx queue.
Fix the misuse of the rx frame status and rx frame length registers: no more
"fifo overrun" errors caused by the OFLOW bit being tested in the frame length
register (instead of the status register), and no more missed packets due to
incorrect length taken from status register (instead of the frame length
register).
Fix a panic (skb_over_panic BUG) caused by allocating and then copying an
incoming packet while the packet length register was changing.
Cut-and-paste the reset code from the powermac mace driver (mace.c), so the NIC
functions when MacOS does not initialise it (important for anyone wanting to
use the Emile boot loader).
Cut-and-paste the error counting and timeout recovery code from mace.c.
Fix over allocation of rx buffer memory (it's page order, not page count).
Converted to driver model.
Converted to DMA API.
Since I've run out of ways to make it fail, and since it performs well now,
promote the driver from EXPERIMENTAL status. Tested on both quadra 840av and
660av.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Macintosh CS89x0 Ethernet: Netif updates
Addition of netif_stop_queue() before transmission by Michael Schmitz
skb_copy_{from,to}_linear_data() conversion by Geert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.
Signed-off-by: Alexander E. Patrakov
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
Get rid of the CONFIG_NETPOLL_RX option completely since all the
dependencies have been removed long ago...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: Michael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
migrate ucc_geth to use the common phylib code.
There are several side effects from doing this:
o deprecate 'interface' property specification present
in some old device tree source files in
favour of a split 'max-speed' and 'interface-type'
description to appropriately match definitions
in include/linux/phy.h. Note that 'interface' property
is still honoured if max-speed or interface-type
are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
and upsmr.r10m, instead of reapplying static initial
values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
platform code add 'mdio' type to id list
prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
complexity.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current tc35815 driver is very obsolete and less maintained for a long
time. Replace it with a new driver based on one from CELF patch
archive.
Major advantages of CELF version (version 1.23, for kernel 2.6.10) are:
* Independent of JMR3927.
(Actually independent of MIPS, but AFAIK the chip is used only on
MIPS platforms)
* TX4938 support.
* 64-bit proof.
* Asynchronous and on-demand auto negotiation.
* High performance on non-coherent architecture.
* ethtool support.
* Many bugfixes and cleanups.
And improvoments since version 1.23 are:
* TX4939 support.
* NETPOLL support.
* NAPI support. (disabled by default)
* Reduce memcpy on receiving.
* PM support.
* Many cleanups and bugfixes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected. Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled. A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver attempts to upgrade the FW if the card has the wrong version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds or changes some HW specific settings for spider_net on
Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>
sk98lin is scheduled for removal in July 2007. This patch makes the
deprecation more obvious in the configuration interface. FWIW, Gentoo have
been shipping a patch very similar to this for a long time.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the experimental tag for the pcnet32 NAPI implementation.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The atl1 driver doesn't need NET_PCI. Remove it from Kconfig.
Noticed by Chad Sprouse.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-tc:
[EISA] EISA registration with !CONFIG_EISA
[TC] pmagb-b-fb: Convert to the driver model
[TC] dec_esp: Driver model for the PMAZ-A
[TC] mips: pmag-ba-fb: Convert to the driver model
[TC] defxx: TURBOchannel support
[TC] TURBOchannel support for the DECstation
[TC] MIPS: TURBOchannel resources off-by-one fix
[TC] MIPS: TURBOchannel update to the driver model
This is a set of changes to add TURBOchannel support to the defxx driver. As
at this point the EISA support in the driver has become the only not having
been converted to the driver model, I took the opportunity to convert it as
well. Plus support for MMIO in addition to PIO operation as TURBOchannel
requires it anyway.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver is a modified version of the Attansic reference driver
for the L1 ethernet adapter. Attansic has granted permission for
its inclusion in the mainline kernel.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Atmel MACB Ethernet peripheral is also integrated in the AT91SAM9260
and AT91SAM9263 processors. The differences from the AVR32 version are:
* Single peripheral clock.
* MII/RMII selection bit is inverted.
* Clock enable bit.
Original patch from Patrice Vilchez.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)
Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use bitrev8 for bmac, mace, macmace, macsonic, and skfp drivers.
[akpm@osdl.org: use the API, not the array]
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mirko Lindner <mlindner@syskonnect.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The OAKNET driver:
- has been marked as BROKEN for more than two years and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver is required by the Chelsio T3 RDMA driver posted by
Steve Wise.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SKMC driver has:
- already been marked as BROKEN in 2.6.0 three years ago and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the Silan SC92031/Rsltek 8139D NIC chip.
This chip is found on at least one counterfeit Encore ENL832-TX-RENT NIC
[1], which came with a mini-CD with the 2.4 driver. A slightly older
version of the driver was found at [2]. The main difference between them
is that the newer one has a small bugfix in the RX path, a lot of
gratuitous renaming of functions, all the printable strings changed to show
as a "Rsltek 8139D" [sic], and a PCI ID of 8139 instead of 2031. The
driver on this patch is a rewrite of the vendor drivers (based mostly on
the older one).
Changes from the previous patch sent to netdev:
- Use MMIO instead of PIO
- Changed TX bounce buffers allocation
- Use skb_copy_and_csum_dev
- Several small bug fixes
- Tested for more than just a few minutes each time
[1] See http://www.encore-usa.com/faq.php under ENL832-TX-RENT for more
information
[2] Look for SL_LINUX.ZIP (which is really a .tar.gz) at
http://broadbandforum.in/dataone_Intex_LAN_cardlinux-t4207-s15.html
[3] To compile on 2.6.17, simply add back the last argument to the
interrupt handler in two places, and copy the boolean declarations
from 2.6.19
[akpm@osdl.org: build fixes]
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver tries to enable/disable NAPI at runtime, but
does so in an unsafe manner, and the NAPI interrupt handling is
a mess. Replace it with a compile time selected NAPI implementation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If we separate out LASI and ASP support later, we'll need this.
Plus, this makes it consistent with the ncr700 scsi driver.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Replace driver crc calculation with existing library.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for other versions of the 10G Chelsio boards.
This is basically a port of the vendor driver with the
TOE features removed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/built-in.o: In function `netxen_nic_remove':
netxen_nic_main.c:(.text+0x31b4d): undefined reference to `pci_disable_msi'
netxen_nic_main.c:(.text+0x31b8e): undefined reference to `pci_release_regions'
drivers/built-in.o: In function `netxen_init_module':
netxen_nic_main.c:(.init.text+0x3f17): undefined reference to `pci_module_init'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for the Atmel MACB on-chip ethernet module.
Tested on AVR32/AT32AP7000/ATSTK1000. I've heard rumours that it works
with AT91SAM9260 as well, and it may be possible to share some code with
the at91_ether driver for AT91RM9200.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since previous version:
* Probe for PHY ID instead of depending on it being provided through
platform_data.
* Grab initial ethernet address from the MACB registers instead
of depending on platform_data.
* Set MII/RMII mode correctly.
These changes are mostly about making the driver more compatible with
the at91 infrastructure.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add tsi108/9 on chip Ethernet controller driver support.
The driver code collects the feedback of previous posting form the mailing
list and gives the update.
MPC7448HPC2 platform in arch/powerpc uses tsi108 bridge.
The following is a brief description of the Ethernet controller:
The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to
manage the two physical connection devices (PHYs). Each Ethernet port has
its own statistics monitor that tracks and reports key interface
statistics. Each port supports a 256-entry hash table for address
filtering. In addition, each port is bridged to the Switch Fabric through
a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows. The Ethernet DMA channels use
descriptors set up in memory, the memory map of the device, and access via
the Switch Fabric. The Ethernet Controller’s DMA arbiter handles
arbitration for the Switch Fabric. The Controller also has a register bus
interface for register accesses and status monitor control.
The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each
Ethernet port uses its transmit and receive DMA channels to manage data
flows through buffer descriptors that are predefined by the system (the
descriptors can exist anywhere in the system memory map). These
descriptors are data structures that point to buffers filled with data
ready to transmit over Ethernet, or they point to empty buffers ready to
receive data from Ethernet.
Signed-off-by: Alexandre Bounine <Alexandre.Bounine@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Fix an offset error when reading the CS89x0 ADD_PORT register
[PATCH] spidernet: poor network performance
[PATCH] Spidernet: remove ETH_ZLEN check in earlier patch
[PATCH] bonding: fix an oops when slave device does not provide get_stats
[PATCH] drivers/net: SAA9730: Fix build error
Revert "[PATCH] zd1211rw: Removed unneeded packed attributes"
[PATCH] zd1211rw: Fix of a locking bug
[PATCH] softmac: remove netif_tx_disable when scanning
[PATCH] ieee80211: Fix kernel panic when QoS is enabled
Confusingly NET_PCI is also set for for non-PCI EISA configurations where
building this driver will result in a build error due to a reference to
pci_release_regions.
While at it, remove the EXPERIMENTAL - in all its uglyness and despite
the sincerest attempts of the buggy hardware the driver is known to work.
Also limit the driver to the Atlas board - the only known system to ever
use the SAA9730 before Phillips ended the short live of the SAA9730.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
As Patrick McHardy <kaber@trash.net> suggested, Traffic Shaper is now
obsolete and alternative to it is no longer CBQ, since its problems with
virtual devices, alter Kconfig text to reflect this -- put a link to the
traffic schedulers as a whole.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/Kconfig says:
# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
so remove duplicate 'depends' uses of NETDEVICES.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2 driver is no longer in experimental state.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
changes due to qe_lib changes include:
o removed inclusion of platform header file
o removed platform_device code, replaced with of_device
o removed typedefs
o uint -> u32 conversions
o removed following defines:
QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
because they hid sizeof/in_be32/out_be32 operations from the reader.
o removed irrelevant comments, added others to resemble removed BD_ defines
o const'd and uncasted all get_property() assignments
bugfixes, courtesy of Scott Wood, include:
- Read phy_address as a u32, not u8.
- Match on type == "network" as well as compatible == "ucc_geth", as
device_is_compatible() will only compare up to the length of the
test string, allowing "ucc_geth_phy" to match as well.
- fixes the MAC setting code in ucc_geth.c. The old code was overwriting and dereferencing random stack contents.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Net devices should depend on NETDEVICES, so revert part of
Paolo's previous patch.
See http://marc.theaimsgroup.com/?l=linux-kernel&m=115566326218740&w=2
for history.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code for the EV96100 evaluation board hasn't compiled since at least
November 15, 2003, so it is being deleted as of 2.6.18 due to lack of
a user base.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No 64-bit PPC_MULTIPLATFORM platforms use the mv643xx_eth driver,
so build it only on PPC32.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Sven Luther <sl@bplan-gmbh.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement NAPI changes to pcnet32 driver. Compile default is off.
Listed as experimental.
Len and Don both worked on a NAPI implementation and have both tested
these changes.
An e1000 blasting short packets to the pcnet32 will lockup Don's system
until the receive storm stops. Without NAPI Len's system watchdog would
expire causing the system to reboot. With NAPI the system will stay
operational.
Tested ia32 and ppc64. Tested '970A, '971, '972, '973, '975, '976, and
'978.
The Kconfig changes came from Len. Don is to blame for all the others.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the firmware download URL in Kconfig to match the header
in drivers/net/myri10ge/myri10ge.c.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add NAPI support to the via-rhine driver so that it can handle higher
speeds and doesn't get overloaded by interrupts as easily.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revised version of the forcedeth NAPI support.
This version is based against netdev-2.6#upstream
(after the MAC patches from Ayaz today).
Can't use nv_disable_hw_interrupts because NAPI only wants to
mask off receive irq's and leave the others alone.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a complementary network driver for our ISP4XXX parts.
There is a concurrent effort underway to get the iSCSI driver (qla4xxx)
integrated upstream as well.
I have been through several iterations with the linux-netdev list and have had
much response from Stephen Hemminger.
- Built and tested using kernel 2.6.17-rc4.
- The chip supports two ethernet and two iSCSI functions.
- The functions ql_sem_lock, ql_sem_spinlock, ql_sem_unlock, and
ql_wait_for_drvr_lock are used to protect resources that are shared across
the network and iSCSI functions. This protection is mostly during chip
initialization and resets, but also include link management.
- The PHY/MII are not exported through ethtool due to the fact that the
iSCSI function will control the common link at least 50% of the time.
This driver has been through several iterations on the netdev list and we feel
this driver is ready for inclusion in the upstream kernel.
It has been built and tested on x86 and PPC64 platforms.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert selection of serial line header compression to use CONFIG_SLHC
rather than makefile ifeq uglyness. This makes it easier to select
the SLHC module from other code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (33 commits)
[PATCH] myri10ge - drop workaround pci_save_state() disabling MSI
[PATCH] myri10ge - drop workaround for the missing AER ext cap on nVidia CK804
via-velocity: the link is not correctly detected when the device starts
[PATCH] add b44 to maintainers
[PATCH] WAN: ioremap() failure checks in drivers
[PATCH] WAN: register_hdlc_device() doesn't need dev_alloc_name()
[PATCH] skb_padto()-area fixes in 8390, wavelan
[PATCH] make drivers/net/forcedeth.c:nv_update_pause() static
[PATCH] network driver for Hilscher netx
[PATCH] Dereference in tokenring/olympic.c
[PATCH] Array overrun in drivers/net/wireless/wavelan.c
[PATCH] Remove useless check in drivers/net/pcmcia/xirc2ps_cs.c
[PATCH] 8139cp: add ethtool eeprom support
[PATCH] 8139cp: fix eeprom read command length
[PATCH] b44: update b44 Kconfig entry
[PATCH] b44: update version to 1.01
[PATCH] b44: add wol for old nic
[PATCH] b44: add parameter
[PATCH] b44: add wol
[PATCH] b44: fix manual speed/duplex/autoneg settings
...
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits)
[POWERPC] re-enable OProfile for iSeries, using timer interrupt
[POWERPC] support ibm,extended-*-frequency properties
[POWERPC] Extra sanity check in EEH code
[POWERPC] Dont look for class-code in pci children
[POWERPC] Fix mdelay badness on shared processor partitions
[POWERPC] disable floating point exceptions for init
[POWERPC] Unify ppc syscall tables
[POWERPC] mpic: add support for serial mode interrupts
[POWERPC] pseries: Print PCI slot location code on failure
[POWERPC] spufs: one more fix for 64k pages
[POWERPC] spufs: fail spu_create with invalid flags
[POWERPC] spufs: clear class2 interrupt status before wakeup
[POWERPC] spufs: fix Makefile for "make clean"
[POWERPC] spufs: remove stop_code from struct spu
[POWERPC] spufs: fix spu irq affinity setting
[POWERPC] spufs: further abstract priv1 register access
[POWERPC] spufs: split the Cell BE support into generic and platform dependant parts
[POWERPC] spufs: dont try to access SPE channel 1 count
[POWERPC] spufs: use kzalloc in create_spu
[POWERPC] spufs: fix initial state of wbox file
...
Manually resolved conflicts in:
drivers/net/phy/Makefile
include/asm-powerpc/spu.h
This is a patch for the Hilscher netx builtin ethernet ports. The
netx board support was merged into 2.6.17-git2.
The netx is a arm926 based SoC.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
--
drivers/net/Kconfig | 11
drivers/net/Makefile | 1
drivers/net/netx-eth.c | 516 ++++++++++++++++++++++++++++++++++++++++
include/asm-arm/arch-netx/eth.h | 27 ++
4 files changed, 555 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Creates new config variables PPC_CELL_NATIVE and PPC_IBM_CELL_BLADE.
The existing CONFIG_PPC_CELL is now used to denote the generic
Cell processor support.
PPC_CELL = make descends into platforms/cell
PPC_CELL_NATIVE = add bare metal support
PPC_IBM_CELL_BLADE = add blade device drivers, etc.
Also renames spu_priv1.c to spu_priv1_mmio.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (109 commits)
[ETHTOOL]: Fix UFO typo
[SCTP]: Fix persistent slowdown in sctp when a gap ack consumes rx buffer.
[SCTP]: Send only 1 window update SACK per message.
[SCTP]: Don't do CRC32C checksum over loopback.
[SCTP] Reset rtt_in_progress for the chunk when processing its sack.
[SCTP]: Reject sctp packets with broadcast addresses.
[SCTP]: Limit association max_retrans setting in setsockopt.
[PFKEYV2]: Fix inconsistent typing in struct sadb_x_kmprivate.
[IPV6]: Sum real space for RTAs.
[IRDA]: Use put_unaligned() in irlmp_do_discovery().
[BRIDGE]: Add support for NETIF_F_HW_CSUM devices
[NET]: Add NETIF_F_GEN_CSUM and NETIF_F_ALL_CSUM
[TG3]: Convert to non-LLTX
[TG3]: Remove unnecessary tx_lock
[TCP]: Add tcp_slow_start_after_idle sysctl.
[BNX2]: Update version and reldate
[BNX2]: Use CPU native page size
[BNX2]: Use compressed firmware
[BNX2]: Add firmware decompression
[BNX2]: Allow WoL settings on new 5708 chips
...
Manual fixup for conflict in drivers/net/tulip/winbond-840.c
Add functions to decompress firmware before loading to the internal
CPUs. Compressing the firmware reduces the driver size significantly.
Added file name length sanity check in the gzip header to prevent
going past the end of buffer [suggested by DaveM].
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
convert au1000_eth driver to use PHY framework and garbage collected
functions and identifiers that became unused/obsolete in the process
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In file included from drivers/net/smc911x.c:84:
drivers/net/smc911x.h:46:9: warning: "SMC_USE_16BIT" is not defined
drivers/net/smc911x.h:60:9: warning: "SMC_USE_32BIT" is not defined
drivers/net/smc911x.h:73:10: warning: "SMC_USE_PXA_DMA" is not defined
drivers/net/smc911x.c: In function `smc911x_reset':
drivers/net/smc911x.c:247: warning: implicit declaration of function `SMC_inl'
drivers/net/smc911x.c:249: warning: implicit declaration of function `SMC_outl'
Cc: Dustin McIntire <dustin@sensoria.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>
> The patch was badly wordwrapped. Please fix and resend.
>
OK, I've fixed the wrapping and removed the CONFIG_ARM restriction. I've also did my
best to modify the C style to conform to the comments.
I noticed that the patch is getting ignored by majordomo due to its size >100K.
Should it be broken up somehow to allow posting to the lists?
Signed-off-by: Dustin McIntire <dustin@sensoria.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
kconfig sanitized around drivers/net
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The spidernet drivers uses request_firmware() and thus needs to select
FW_LOADER.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch contains the following possible updates:
- let FORCEDETH no longer depend on EXPERIMENTAL
- remove the "Reverse Engineered" from the option text:
for the user it's important which hardware the driver supports, not
how it was developed
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve reference to PCI NE2K support in ISA NE2K documentation.
Original 2.4 patch From: Ged Haywood <ged@jubileegroup.co.uk>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This documentation is mostly obsolete, and should therefore either be
updated or removed (this patch does the latter).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>From : Dale Farnsworth <dale@farnsworth.org>
Recent patches for the mv643xx_eth driver now use the MII interface
library. Select MII so it gets built when that driver is selected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Take the experimental dependency of skge driver, it is as stable as the
others.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sk98lin driver was changed a while ago to remove support for the
D-Link 530T card because that hardware has no working VPD data. The help
text for Kconfig was not updated.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch corrects a few spelling and grammar errors found in
drivers/net
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the whole netdevices menu depend on NET, rather than having an empty
submenu when networking is disabled.
Indeed, almost the whole body of the menu was surrounded by if NETDEVICES,
and what was outside depended on NETCONSOLE which is inside the menu.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some users have commented that it is unclear which driver they should be
using for their Marvell/SysKonnect network adapter, and which ones
are/aren't interchangable.
This patch attempts to reduce the confusion.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
*) mark as "EXPERIMENTAL" various items that either aren't very stable or
that are actively crashing the setup of users which don't really need them
(i.e. HIGHMEM and 3-level pagetables on x86 - nobody needs either,
everybody reports "I'm using it and getting trouble").
*) move net/Kconfig near to the rest of network configurations, and
drivers/block/Kconfig near "Block layer" submenu.
*) it's useless and doesn't work well to force NETDEVICES on and to disable
the prompt like it's done. Better remove the attempt, and change that to a
simple "default y if UML".
*) drop the warning about "report problems about HPPFS" - it's redundant
anyway, as that's the usual procedure, and HPPFS users are especially
technical (i.e. they know reporting bugs is _good_).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for the Intel IXDP2351 to the CS89x0 driver.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the help text of the cs89x0 network driver Kconfig entry.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the ColdFire FEC ethernet driver to be enabled on the M520x CPU
family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A new device to do intermidiate functional block in a system shared
manner. To use the new functionality, you need to turn on
qos/classifier actions.
The new functionality can be grouped as:
1) qdiscs/policies that are per device as opposed to system wide. ifb
allows for a device which can be redirected to thus providing an
impression of sharing.
2) Allows for queueing incoming traffic for shaping instead of
dropping.
Packets are redirected to this device using tc/action mirred redirect
construct. If they are sent to it by plain routing instead then they
will merely be dropped and the stats would indicate that.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a wrong indentation.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MIPS dependency for dm9000 ethernet controller. Indeed this controller
is used by some embedded platforms based on MIPS CPUs.
Signed-off-by: Franck Bui-Huu <franck.bui@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PNX010X support for CS89x0 should be conditional on NET_PCI, as it is an 'on
board controller' and NET_PCI includes that category of NICs. Since
ARCH_PNX0105 was recently changed to ARCH_PNX010X, incorporate that change as
well while we're at it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We changed the name of the Kconfig symbols along with
the move to arch/powerpc. This one hunk got lost during
the conversion.
From: Jens.Osterkamp@de.ibm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Eliminate special case for EC-A1. The overhead isn't so
great that having config option is worth it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The way the hardware and firmware work is that there is one shared RX
queue and IRQ for a number of different network interfaces. Due to this,
we would like to process received packets for every interface in the same
NAPI poll handler, so we need a pseudo-device to schedule polling on.
What the driver currently does is that it always schedules polling for
the first network interface in the list, and processes packets for every
interface in the poll handler for that first interface -- however, this
scheme breaks down if the first network interface happens to not be up,
since netif_rx_schedule_prep() checks netif_running().
sky2 apparently has the same issue, and Stephen Hemminger suggested a
way to work around this: create a variant of netif_rx_schedule_prep()
that does not check netif_running(). I implemented this locally and
called it netif_rx_schedule_prep_notup(), and it seems to work well,
but it's something that probably not everyone would be happy with.
The ixp2000 is an ARM CPU with a high-speed network interface in the
CPU itself (full duplex 4Gb/s or 10Gb/s depending on the IXP model.)
The CPU package also contains 8 or 16 (again depending on the IXP
model) 'microengines', which are somewhat primitive but very fast
and efficient processor cores which can be used to offload various
things from the main CPU.
This driver makes the high-speed network interface in the CPU visible
and usable as a regular linux network device. Currently, it only
supports the Radisys ENP2611 IXP board, but adding support for other
board types should be fairly easy.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patch support the SMC9111 present on DB1200 boards.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Matt Domsch <Matt_Domsch@dell.com>
The patch below implements the Microsoft Point-to-Point Encryption method
as a PPP compressor/decompressor. This is necessary for Linux clients and
servers to interoperate with Microsoft Point-to-Point Tunneling Protocol
(PPTP) servers (either Microsoft PPTP servers or the poptop project) which
use MPPE to encrypt data when creating a VPN.
This patch differs from the kernel_ppp_mppe DKMS pacakge at
pptpclient.sourceforge.net by utilizing the kernel crypto routines rather
than providing its own SHA1 and arcfour implementations.
Minor changes to ppp_generic.c try to prevent a link from disabling
compression (in our case, the encryption) after it has started using
compression (encryption).
Feedback to <pptpclient-devel@lists.sourceforge.net> please.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: James Cameron <james.cameron@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
This patch provides dynamic two buffer-mode and 3 buffer-mode options.
Previously 2 buffer-mode was compilation option. Now with this patch applied
one can load driver in 2 buffer-mode with module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=2
This patch also provides 3 buffer-mode which provides header separation
functionality. In 3 buffer-mode skb->data will have L2/L3/L4 headers and
"skb_shinfo(skb)->frag_list->data" will have have L4 payload.
one can load driver in 3 buffer-mode with same above module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=3
Please review the patch.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch replaces current PowerPC 4xx EMAC driver with
new, re-written from the scratch version. This patch is quite big
(~234K) because there is virtualy 0% of common code between old and
new version.
New driver uses NAPI, it solves stability problems under heavy packet
load and low memory, corrects chip register access and fixes numerous
small bugs I don't even remember now.
This patch has been tested on all supported in 2.6 PPC 4xx boards.
It's been used in production for almost a year now on custom
4xx hardware. PPC32 specific parts are already upstream.
Patch was acked by the current EMAC driver maintainer (Matt Porter). I
will be maintaining this new version.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
--
Kconfig | 72
ibm_emac/Makefile | 13
ibm_emac/ibm_emac.h | 418 +++--
ibm_emac/ibm_emac_core.c | 3414 ++++++++++++++++++++++++----------------------
ibm_emac/ibm_emac_core.h | 313 ++--
ibm_emac/ibm_emac_debug.c | 377 ++---
ibm_emac/ibm_emac_debug.h | 63
ibm_emac/ibm_emac_mal.c | 674 +++++----
ibm_emac/ibm_emac_mal.h | 336 +++-
ibm_emac/ibm_emac_phy.c | 335 ++--
ibm_emac/ibm_emac_phy.h | 105 -
ibm_emac/ibm_emac_rgmii.c | 201 ++
ibm_emac/ibm_emac_rgmii.h | 68
ibm_emac/ibm_emac_tah.c | 111 +
ibm_emac/ibm_emac_tah.h | 96 -
ibm_emac/ibm_emac_zmii.c | 255 +++
ibm_emac/ibm_emac_zmii.h | 114 -
17 files changed, 4114 insertions(+), 2851 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
IXDP2x01 systems can be built without PCI network cards, so we should not
require NET_PCI to build CS89x0 on these systems.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The documentation about s2io is available at
Documentation/networking/s2io.txt.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch from Jon Ringle
This patch gives support for the CS8900A ethernet chip on the Comdial MP1000
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes pocket and parallel adaptors to depend on PARPORT
instead of ISA in order to get the option in newer SuperIO based systems.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
