[ Upstream commit d5cc0a1fcb ]
During firmware and library download, sometimes it is observed that
firmware and library download is timed-out resulting into probe failure.
This patch disables dynamic clock gating while firmware and library
download.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d389b1251 ]
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e48e5e198f ]
The commit 1a1c116f3d ("RDMA/netlink: Simplify the put_msg and put_attr")
removes nlmsg_len calculation in ibnl_put_attr causing netlink messages and
caused to miss source and destination addresses.
Fixes: 1a1c116f3d ("RDMA/netlink: Simplify the put_msg and put_attr")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d36f45e5b4 ]
Address/port initialization should work correctly regardless
of the order in which command line arguments are supplied,
E.g, cfg_port should be used to connect to the remote host
even if it is processed after -D, src/dst address initialization
should not require that [-4|-6] be specified before
the -S or -D args, receiver should be able to bind to *.<cfg_port>
Achieve this by making sure that the address/port structures
are initialized after all command line options are parsed.
Store cfg_port in host-byte order, and use htons()
to set up the sin_port/sin6_port before bind/connect,
so that the network system calls get the correct values
in network-byte order.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63f1e05f7f ]
df->governor is being dereferenced before it is null checked,
hence there is a potential null pointer dereference.
Notice that df->governor is being null checked at line 1004:
if (df->governor) {, which implies it might be null.
Fix this by null checking df->governor before dereferencing it.
Addresses-Coverity-ID: 1401988 ("Dereference before null check")
Fixes: bcf23c79c4 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 12a26c298d ]
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1bfe888938 ]
The only way of stopping the watchdog is by resetting it.
Add the watchdog op for stopping the device and reset if
a reset line is provided.
At same time WDOG_HW_RUNNING should be remove from dw_wdt_start.
As commented by Guenter Roeck:
dw_wdt sets WDOG_HW_RUNNING in its open function. Result is
that the kref_get() in watchdog_open() won't be executed. But then
kref_put() in close will be called since the watchdog now does stop.
This causes the imbalance.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61647823aa ]
d_move() will call __d_drop() and then __d_rehash()
on the dentry being moved. This creates a small window
when the dentry appears to be unhashed. Many tests
of d_unhashed() are made under ->d_lock and so are safe
from racing with this window, but some aren't.
In particular, getcwd() calls d_unlinked() (which calls
d_unhashed()) without d_lock protection, so it can race.
This races has been seen in practice with lustre, which uses d_move() as
part of name lookup. See:
https://jira.hpdd.intel.com/browse/LU-9735
It could race with a regular rename(), and result in ENOENT instead
of either the 'before' or 'after' name.
The race can be demonstrated with a simple program which
has two threads, one renaming a directory back and forth
while another calls getcwd() within that directory: it should never
fail, but does. See:
https://patchwork.kernel.org/patch/9455345/
We could fix this race by taking d_lock and rechecking when
d_unhashed() reports true. Alternately when can remove the window,
which is the approach this patch takes.
___d_drop() is introduce which does *not* clear d_hash.pprev
so the dentry still appears to be hashed. __d_drop() calls
___d_drop(), then clears d_hash.pprev.
__d_move() now uses ___d_drop() and only clears d_hash.pprev
when not rehashing.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a42b63c1ac ]
Change the default mapping between TC and TCG as follows:
Prio | TC/TCG
| from to
| (set by FW) (set by SW)
---------+-----------------------------------
0 | 0/0 0/7
1 | 1/0 0/6
2 | 2/0 0/5
3 | 3/0 0/4
4 | 4/0 0/3
5 | 5/0 0/2
6 | 6/0 0/1
7 | 7/0 0/0
These new settings cause that a pause frame for any prio stops
traffic for all prios.
Fixes: 564c274c3d ("net/mlx4_en: DCB QoS support")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5928c28152 ]
We're seeing a lot of bogus backlight interfaces on newer machines without
a LCD such as desktops, servers and HDMI sticks. This causes userspace to
show a non-functional brightness slider in e.g. the GNOME3 system menu,
which is undesirable. And, in general, we should simply just not register
a non functional backlight interface.
Checking the LCD flag causes the bogus acpi_video backlight interfaces to
go away (on the machines this was tested on).
This change sets the lcd_only option by default on any machines which
are Win8-ready, to fix this.
This is not entirely without a risk of regressions, but video_detect.c
already prefers native-backlight interfaces over the acpi_video one
on Win8-ready machines, calling acpi_video_unregister_backlight() as soon
as a native interface shows up. This is done because the ACPI backlight
interface often is broken on Win8-ready machines, because win8 does not
seem to actually use it.
So in practice we already end up not registering the ACPI backlight
interface on (most) Win8-ready machines with a LCD panel, thus this
change does not change anything for (most) machines with a LCD panel
and on machines without a LCD panel we actually don't want to register
any backlight interfaces.
This has been tested on the following machines and fixes a bogus backlight
interface showing up there:
- Desktop with an Asrock B150M Pro4S/D3 m.b. using i5-6500 builtin gfx
- Intel Compute Stick STK1AW32SC
- Meegopad T08 HDMI stick
Bogus backlight interfaces have also been reported on:
- Desktop with Asus H87I-Plus m.b.
- Desktop with ASRock B75M-ITX m.b.
- Desktop with Gigabyte Z87-D3HP m.b.
- Dell PowerEdge T20 desktop
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1097436
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133327
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133329
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133646
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ae0c649c4 ]
If the rds_sock is not added to the bind_hash_table, we must
reset rs_bound_addr so that rds_remove_bound will not trip on
this rds_sock.
rds_add_bound() does a rds_sock_put() in this failure path, so
failing to reset rs_bound_addr will result in a socket refcount
bug, and will trigger a WARN_ON with the stack shown below when
the application subsequently tries to close the PF_RDS socket.
WARNING: CPU: 20 PID: 19499 at net/rds/af_rds.c:496 \
rds_sock_destruct+0x15/0x30 [rds]
:
__sk_destruct+0x21/0x190
rds_remove_bound.part.13+0xb6/0x140 [rds]
rds_release+0x71/0x120 [rds]
sock_release+0x1a/0x70
sock_close+0xe/0x20
__fput+0xd5/0x210
task_work_run+0x82/0xa0
do_exit+0x2ce/0xb30
? syscall_trace_enter+0x1cc/0x2b0
do_group_exit+0x39/0xa0
SyS_exit_group+0x10/0x10
do_syscall_64+0x61/0x1a0
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 820da53575 ]
Report offset parameter in L2TP_CMD_SESSION_GET command if
it has been configured by userspace
Fixes: 309795f4be ("l2tp: Add netlink control API for L2TP")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27b5bf49f0 ]
When phy exists, we use the value of phydev.autoneg to represent the
auto-negotiation state of hardware. Otherwise, we use the value of
mac.autoneg to represent it.
This patch fixes for getting a error value of auto-negotiation state in
hclge_get_autoneg().
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99fdf6b1ca ]
This patch fixes a memory leak problems in change tqps process,
the function hns3_uninit_all_ring and hns3_init_all_ring
may be called many times.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca8000684e ]
While monitoring a multithread process with pid option, perf sometimes
may return sys_perf_event_open failure with 3(No such process) if any of
the process's threads die before we open the event. However, we want
perf continue monitoring the remaining threads and do not exit with
error.
Here, the patch enables perf_evsel::ignore_missing_thread for -p option
to ignore complete failure if any of threads die before we open the event.
But it may still return sys_perf_event_open failure with 22(Invalid) if we
monitors several event groups.
sys_perf_event_open: pid 28960 cpu 40 group_fd 118202 flags 0x8
sys_perf_event_open: pid 28961 cpu 40 group_fd 118203 flags 0x8
WARNING: Ignored open failure for pid 28962
sys_perf_event_open: pid 28962 cpu 40 group_fd [118203] flags 0x8
sys_perf_event_open failed, error -22
That is because when we ignore a missing thread, we change the thread_idx
without dealing with its fds, FD(evsel, cpu, thread). Then get_group_fd()
may return a wrong group_fd for the next thread and sys_perf_event_open()
return with 22.
sys_perf_event_open(){
...
if (group_fd != -1)
perf_fget_light()//to get corresponding group_leader by group_fd
...
if (group_leader)
if (group_leader->ctx->task != ctx->task)//should on the same task
goto err_context
...
}
This patch also fixes this bug by introducing perf_evsel__remove_fd() and
update_fds to allow removing fds for the missing thread.
Changes since v1:
- Change group_fd__remove() into a more genetic way without changing code logic
- Remove redundant condition
Changes since v2:
- Use a proper function name and add some comment.
- Multiline comment style fixes.
Committer testing:
Before this patch the recently added 'perf stat --per-thread' for system
wide counting would race while enumerating all threads using /proc:
[root@jouet ~]# perf stat --per-thread
failed to parse CPUs map: No such file or directory
Usage: perf stat [<options>] [<command>]
-C, --cpu <cpu> list of cpus to monitor in system-wide
-a, --all-cpus system-wide collection from all CPUs
[root@jouet ~]# perf stat --per-thread
failed to parse CPUs map: No such file or directory
Usage: perf stat [<options>] [<command>]
-C, --cpu <cpu> list of cpus to monitor in system-wide
-a, --all-cpus system-wide collection from all CPUs
[root@jouet ~]#
When, say, the kernel was being built, so lots of shortlived threads,
after this patch this doesn't happen.
Signed-off-by: Mengting Zhang <zhangmengting@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Cheng Jian <cj.chengjian@huawei.com>
Cc: Li Bin <huawei.libin@huawei.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1513148513-6974-1-git-send-email-zhangmengting@huawei.com
[ Remove one use 'evlist' alias variable ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f5c6d8777 ]
This improve the error message so that user can know event-name error
before writing new events to kprobe-events interface.
E.g.
======
#./perf probe -x /lib64/libc-2.25.so malloc_get_state*
Internal error: "malloc_get_state@GLIBC_2" is an invalid event name.
Error: Failed to add events.
======
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: bhargavb <bhargavaramudu@gmail.com>
Cc: linux-rt-users@vger.kernel.org
Link: http://lkml.kernel.org/r/151275040665.24652.5188568529237584489.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b3a2716dd ]
Commit d80406453a ("perf symbols: Allow user probes on versioned
symbols") allows user to find default versioned symbols (with "@@") in
map. However, it did not enable normal versioned symbol (with "@") for
perf-probe. E.g.
=====
# ./perf probe -x /lib64/libc-2.25.so malloc_get_state
Failed to find symbol malloc_get_state in /usr/lib64/libc-2.25.so
Error: Failed to add events.
=====
This solves above issue by improving perf-probe symbol search function,
as below.
=====
# ./perf probe -x /lib64/libc-2.25.so malloc_get_state
Added new event:
probe_libc:malloc_get_state (on malloc_get_state in /usr/lib64/libc-2.25.so)
You can now use it in all perf tools, such as:
perf record -e probe_libc:malloc_get_state -aR sleep 1
# ./perf probe -l
probe_libc:malloc_get_state (on malloc_get_state@GLIBC_2.2.5 in /usr/lib64/libc-2.25.so)
=====
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: bhargavb <bhargavaramudu@gmail.com>
Cc: linux-rt-users@vger.kernel.org
Link: http://lkml.kernel.org/r/151275049269.24652.1639103455496216255.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09ee9dba96 ]
If SNAT modifies the source address the resulting packet might match
an IPsec policy, reinject the packet if that's the case.
The exact same thing is already done for IPv4.
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5c7b4d5ac ]
Commit a22950c888 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86aacdca66 ]
"rem * SDM_DEN" can easily overflow on the 32-bit Meson8 and Meson8b
SoCs if the "remainder" (after the division operation) is greater than
262143Hz. This is likely to happen since the input clock for the MPLLs
on Meson8 and Meson8b is "fixed_pll", which is running at a rate of
2550MHz.
One example where this was observed to be problematic was the Ethernet
clock calculation (which takes MPLL2 as input). When requesting a rate
of 125MHz there is a remainder of 2500000Hz.
The resulting MPLL2 rate before this patch was 127488329Hz.
The resulting MPLL2 rate after this patch is 124999103Hz.
Commit b609338b26 ("clk: meson: mpll: use 64bit math in
rate_from_params") already fixed a similar issue in rate_from_params.
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce9ce74145 ]
Casting to u16 before validating IRD/ORD connection
parameters could cause recording wrong IRD/ORD values
in the cm_node. Validate the IRD/ORD parameters as
they are passed by the application before recording
them.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe99afd1fe ]
Lower Inbound RDMA Read Queue (Q1) object count by a factor of 2
as it is incorrectly doubled. Also, round up Q1 and Transmit FIFO (XF)
object count to power of 2 to satisfy hardware requirement.
Fixes: 86dbcd0f12 ("i40iw: add file to handle cqp calls")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df8b13a1b2 ]
Partial FPDU processing is broken as the sequence number
for the first partial FPDU is wrong due to incorrect
Q2 buffer offset. The offset should be 64 rather than 16.
Fixes: 786c6adb3a ("i40iw: add puda code")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e6cfc52516 which is
commit 53c81e95df upstream.
Ben writes that there are a number of follow-on patches needed to fix
this up, but they get complex to backport, and some custom fixes are
needed, so let's just revert this and wait for a "real" set of patches
to resolve this to be submitted if it is really needed.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Petr Vorel <pvorel@suse.cz>
Cc: Alexey Kodanev <alexey.kodanev@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0049457bfd which was
commit a8b149d32b upstream.
The backport was not correct, so just drop it entirely.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2f1f60c4b9 which was
commit 7be4b5dc7f upstream.
It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0ed43f944a which was
comit e153db03c6 upstream.
It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd5c4facf5 upstream.
I'm getting a slab named "biovec-(1<<(21-12))". It is caused by unintended
expansion of the macro BIO_MAX_PAGES. This patch renames it to biovec-max.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d61d263c8d upstream.
The driver implementation returns support for private flags, while
no private flags are present. When asked for the number of private
flags it returns the number of statistic flag names.
Fix this by returning EOPNOTSUPP for not implemented ethtool flags.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65d9982d7e upstream.
ECMA-48 [1] (aka ISO 6429) has defined SGR 21 as "doubly underlined"
since at least March 1984. The Linux kernel has treated it as SGR 22
"normal intensity" since it was added in Linux-0.96b in June 1992.
Before that, it was simply ignored. Other terminal emulators have
either ignored it, or treat it as double underline now. xterm for
example added support in its 304 release (May 2014) [2] where it was
previously ignoring it.
Changing this behavior shouldn't be an issue:
- It isn't a named capability in ncurses's terminfo database, so no
script is using libtinfo/libcurses to look this up, or using tput
to query & output the right sequence.
- Any script assuming SGR 21 will reset intensity in all terminals
already do not work correctly on non-Linux VTs (including running
under screen/tmux/etc...).
- If someone has written a script that only runs in the Linux VT, and
they're using SGR 21 (instead of SGR 22), the output should still
be readable.
imo it's important to change this as the Linux VT's non-conformance
is sometimes used as an argument for other terminal emulators to not
implement SGR 21 at all, or do so incorrectly.
[1]: https://www.ecma-international.org/publications/standards/Ecma-048.htm
[2]: 2fd29cb98d
Signed-off-by: Mike Frysinger <vapier@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04bb1719c4 upstream.
The touch sensor buttons on Sony VAIO VGN-CS series laptops (e.g.
VGN-CS31S) are a separate PS/2 device. As the MUX is disabled for all
VAIO machines by the nomux blacklist, the data from touch sensor
buttons and touchpad are combined. The protocol used by the buttons is
probably similar to the touchpad protocol (both are Synaptics) so both
devices get enabled. The controller combines the data, creating a mess
which results in random button clicks, touchpad stopping working and
lost sync error messages:
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 4
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: issuing reconnect request
Add a new i8042_dmi_forcemux_table whitelist with VGN-CS.
With MUX enabled, touch sensor buttons are detected as separate device
(and left disabled as there's currently no driver), fixing all touchpad
problems.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b56af54ac7 upstream.
Reset i8042 before probing because of insufficient BIOS initialisation of
the i8042 serial controller. This makes Synaptics touchpad detection
possible. Without resetting the Synaptics touchpad is not detected because
there are always NACK messages from AUX port.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 567b9b549c upstream.
The primary interface for the touchpad device in Thinkpad L570 is SMBus,
so ALPS overlooked PS2 interface Firmware setting of TrackStick, and
shipped with TrackStick otp bit is disabled.
The address 0xD7 contains device number information, so we can identify
the device by checking this value, but to access it we need to enable
Command mode, and then re-enable the device. Devices shipped in Thinkpad
L570 report either 0x0C or 0x1D as device numbers, if we see them we assume
that the devices are DualPoints.
The same issue exists on Dell Latitude 7370.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196929
Fixes: 646580f793 ("Input: ALPS - fix multi-touch decoding on SS4 plus touchpads")
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Tested-by: Jaak Ristioja <jaak@ristioja.ee>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9de9a44948 upstream.
This reverts commit 452562abb5 ("base: arch_topology: fix section
mismatch build warnings"). It causes the notifier call hangs in some
use-cases.
In some cases with using maxcpus, some of cpus are booted first and
then the remaining cpus are booted. As an example, some users who want
to realize fast boot up often use the following procedure.
1) Define all CPUs on device tree (CA57x4 + CA53x4)
2) Add "maxcpus=4" in bootargs
3) Kernel boot up with CA57x4
4) After kernel boot up, CA53x4 is booted from user
When kernel init was finished, CPUFREQ_POLICY_NOTIFIER was not still
unregisterd. This means that "__init init_cpu_capacity_callback()"
will be called after kernel init sequence. To avoid this problem,
it needs to remove __init{,data} annotations by reverting this commit.
Also, this commit was needed to fix kernel compile issue below.
However, this issue was also fixed by another patch: commit 82d8ba717c
("arch_topology: Fix section miss match warning due to
free_raw_capacity()") in v4.15 as well.
Whereas commit 452562abb5 added all the missing __init annotations,
commit 82d8ba717c removed it from free_raw_capacity().
WARNING: vmlinux.o(.text+0x548f24): Section mismatch in reference
from the function init_cpu_capacity_callback() to the variable
.init.text:$x
The function init_cpu_capacity_callback() references
the variable __init $x.
This is often because init_cpu_capacity_callback lacks a __init
annotation or the annotation of $x is wrong.
Fixes: 82d8ba717c ("arch_topology: Fix section miss match warning due to free_raw_capacity()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gaku Inami <gaku.inami.xh@renesas.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1d9fc04c4 upstream.
Ack ai fifo error interrupts in interrupt handler to clear interrupt
after fifo overflow. It should prevent lock-ups after the ai fifo
overflows.
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5811375325 upstream.
Fstests generic/475 provides a way to fail metadata reads while
checking if checksum exists for the inode inside run_delalloc_nocow(),
and csum_exist_in_range() interprets error (-EIO) as inode having
checksum and makes its caller enter the cow path.
In case of free space inode, this ends up with a warning in
cow_file_range().
The same problem applies to btrfs_cross_ref_exist() since it may also
read metadata in between.
With this, run_delalloc_nocow() bails out when errors occur at the two
places.
cc: <stable@vger.kernel.org> v2.6.28+
Fixes: 17d217fe97 ("Btrfs: fix nodatasum handling in balancing code")
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f461b1e02 upstream.
With ecb-cast5-avx, if a 128+ byte scatterlist element followed a
shorter one, then the algorithm accidentally encrypted/decrypted only 8
bytes instead of the expected 128 bytes. Fix it by setting the
encryption/decryption 'fn' correctly.
Fixes: c12ab20b16 ("crypto: cast5/avx - avoid using temporary stack buffers")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aaf49b495 upstream.
The decision to rebuild .S_shipped is made based on the relative
timestamps of .S_shipped and .pl files but git makes this essentially
random. This means that the perl script might run anyway (usually at
most once per checkout), defeating the whole purpose of _shipped.
Fix by skipping the rule unless explicit make variables are provided:
REGENERATE_ARM_CRYPTO or REGENERATE_ARM64_CRYPTO.
This can produce nasty occasional build failures downstream, for example
for toolchains with broken perl. The solution is minimally intrusive to
make it easier to push into stable.
Another report on a similar issue here: https://lkml.org/lkml/2018/3/8/1379
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a9eb80e64 upstream.
rsa-pkcs1pad uses a value returned from a RSA implementation max_size
callback as a size of an input buffer passed to the RSA implementation for
encrypt and sign operations.
CCP RSA implementation uses a hardware input buffer which size depends only
on the current RSA key length, so it should return this key length in
the max_size callback, too.
This also matches what the kernel software RSA implementation does.
Previously, the value returned from this callback was always the maximum
RSA key size the CCP hardware supports.
This resulted in this huge buffer being passed by rsa-pkcs1pad to CCP even
for smaller key sizes and then in a buffer overflow when ccp_run_rsa_cmd()
tried to copy this large input buffer into a RSA key length-sized hardware
input buffer.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: ceeec0afd6 ("crypto: ccp - Add support for RSA on the CCP")
Cc: stable@vger.kernel.org
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 900a081f69 upstream.
When we have an unaligned SG list entry where there is no leftover
aligned data, the hash walk code will incorrectly return zero as if
the entire SG list has been processed.
This patch fixes it by moving onto the next page instead.
Reported-by: Eli Cooper <elicooper@gmx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 333e18c5cc upstream.
The RSA private key for the first form should have
version, prime1, prime2, exponent1, exponent2, coefficient
values 0.
With non-zero values for prime1,2, exponent 1,2 and coefficient
the Intel QAT driver will assume that values are provided for the
private key second form. This will result in signature verification
failures for modules where QAT device is present and the modules
are signed with rsa,sha256.
Cc: <stable@vger.kernel.org>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Conor McLoughlin <conor.mcloughlin@intel.com>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f962eb46e7 upstream.
In this driver the clock is got but never put when the driver is removed
or if there is an error in the probe.
Using the managed version of clk_get() allows to let the kernel take care
of it.
Fixes: 1b44c5a60c ("crypto: inside-secure - add SafeXcel EIP197 crypto
engine driver")
cc: stable@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9bdab212 upstream.
The buffer rctx->ext contains potentially sensitive data and should
be freed with kzfree.
Cc: <stable@vger.kernel.org>
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
