Ls1012a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1088a platform, the i2c input clock is actually platform pll CLK / 8
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the nodes to include little-endian
property to be consistent with the hardware.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Thermal Monitoring Unit (TMU) monitors and reports the
temperature from 2 remote temperature measurement sites
located on ls1028a chip.
Add TMU dts node to enable this feature.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since fsl-ls1088a Soc GPIO registers are used as little endian,
the patch adds the little-endian attribute to each gpio node.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the console device tree node for the following
DPAA2 based platforms: LS1088A, LS2080A, LS2088A and LX2160A.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.
Additional subsystems that are active :
- Ethernet
- USB
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch use the optional property node "arm,malidp-arqos-value" to
can be dynamic configure QoS signaling.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for i.MX8QXP AI_ML board from Einfochips. This board is one
of the Consumer Edition boards of the 96Boards family based on i.MX8QXP
SoC from NXP/Freescale.
The initial support includes following peripherals which are tested and
known to be working:
1. Debug serial via UART2
2. uSD
3. WiFi
4. Ethernet
More information about this board can be found in Arrow website:
https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All these at803x properties are not documented anywhere, so
just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1046afrwy board is based on nxp ls1046a SoC.
Board support's 4GB ddr memory, i2c, microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the charge controller node. With the controller driver loaded
the VBUS of the user USB socket is controlled exclusively via i2c
with the GPIO controls ignored, so vbus-supply for the user USB
port must be linked to the charge controller.
Hog the previously used GPIO control to unconditionally enable
VBUS until the driver is loaded.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct clock for "bus_early", "ref", "suspend" should be:
IMX8MQ_CLK_USB1_CTRL_ROOT, IMX8MQ_CLK_USB_CORE_REF, IMX8MQ_CLK_32K,
especially we may need the right suspend clock rate to set register
in controller driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for TMU module, add clock info to TMU
node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.
That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf
Fixes: 12629c5c37 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.0.2, 04/2019) from below links,
1.8GHz is ONLY available for consumer part, so the market segment
bits for 1.8GHz opp should ONLY available for consumer part accordingly.
https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf
Fixes: f403a26c86 (arm64: dts: imx8mm: Add cpu speed grading and all OPPs)
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The same ddr perfomance counter IP from 8qxp is also available on imx8m
series so add it to dts.
Tested with `perf stat` and `memtester` on imx8mm-evk and obtained
plausible results.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB1 port has typec connector with power delivery support:
- Dual data role: host and device.
- Dual power role: source and sink, prefer power sink.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since IMX8MM_CLK_USB_CORE_REF is not used at all, so remove the setting
for it.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MM pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MQ pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial configuration for clocks that need default parent and rate
setting. This is based on the vendor tree clock provider parents and rates
configuration except this is doing the setup in dts rather than using clock
consumer API in a clock provider driver.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix several warnings/errors in validation of binding schemas.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAl0zzmkQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw0YYD/9Uq8Oj9WG9NP8QeJt1qZIVIu4GMRqCiijM
ApXu9RAsQvaakwRiqaOufFSACIP/yjxHadbncObMWq7uGLT2TVxZwhR8XeOoi+Ft
UO/2KosTbTpMeAjFB1Dz/f0IbUa4Ro5ZiP5kohGNi5X/IdsCAC0ypFk3cCIx4Siz
/gr+cN+ef9p6cOy+vGzEGRMSDULbun/9cZmctDpMf9ZFUMu8xA/nn6qTEck3mQ2j
OX465qPGrstZKlO3C2NVSyUip8/NLhTrUeDCCNTFw6fOIxRCjQfIj0MNMnm+pjO3
/xPDQV0Swv+LjT+HSJA8TyEXKQP28N+v9K9bP4e59PPAf2raGX1khwvMM5bJuy//
2K8mDmAJrP5wy/9aFq8bPdzWQZzfPefDW1PCBNtZybo6OlppDu+4uX7FonjRI/nj
7AzS3qch4v4i1sJmADgysn9yOUgzUvJf/SLD1f5XHsiEa0RXr51QWVxvJaRs24wS
U/vzyZq6vqtTBSOzXpjIK0Yj+D7f05qT0MsPK5lbynCdByLli3xhbte8AwGg57RW
4CtPTZLdPVvIlCZ3jNOZXq9OizRSBokaj155YvSKQ9nzcnbHfEF4JctJQ+K3tdwS
6s4FVrgNxtXN9KidfBCnWDj+1eS1ZxeCmKo1Ypxhj9/t80NXt7b7dwEJ8H91/YuU
GfLancHPHQ==
=IkH4
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"Fix several warnings/errors in validation of binding schemas"
* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
Pull vfs documentation typo fix from Al Viro.
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
typo fix: it's d_make_root, not d_make_inode...
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEE6fsu8pdIjtWE/DpLiiy9cAdyT1EFAl0zg9YACgkQiiy9cAdy
T1HEtQv/Vn2vb9jPoqbCc5QfSUDL13dNYyxhqt3xPdbb3m49a7XNHLoBByM/pnMu
TF10QdOPkPS5eP5OTDpR7iwS9iNX9+8KGtlqlbzX7z+bwQmGbBQXg3VoYahSeeGU
soJE8VgqoeoOkPV9Sl8tojOIVk6B+BAv4iRPpswt8iPD8Y8IPRg3ONZNoomybzfG
GlQBFabhxJU8VLkJIb4NVB+E4AlgMDueD7HpCXD2zh6xsEULgRs2wwxfEopZlyzh
prjNY6OZliXMuTMNLw2D07xlya3ZqaXOt+hHEuvSB//YxooTVxBme70ycLF47N3q
Gvmaw8QB6scl110PHud9luqpHhdJsEvKOKr0Amv2ND2Atb098D0kZ+VITRP3QHt5
LZcHtKNRXDpAvkHphgN0W5O0ngdFDFo197BaWdwPmi9rARPhuQPq61vkFpsrPwN2
AxkG7IQANNJh4bII6/+xBpSjmtInm0BQhxuojpHIYGiZvdHNYMrJfwFcAoVWfVvl
b9MtG9Qz
=rP0b
-----END PGP SIGNATURE-----
Merge tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two fixes for stable, one that had dependency on earlier patch in this
merge window and can now go in, and a perf improvement in SMB3 open"
* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: flush before set-info if we have writeable handles
smb3: optimize open to not send query file internal info
cifs: copy_file_range needs to strip setuid bits and update timestamps
CIFS: fix deadlock in cached root handling
The commit b3aa14f022 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.
kernel BUG at drivers/iommu/iova.c:801!
Workqueue: kblockd blk_mq_run_work_fn
RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
Call Trace:
free_cpu_cached_iovas+0xbd/0x150
alloc_iova_fast+0x8c/0xba
dma_ops_alloc_iova.isra.6+0x65/0xa0
map_sg+0x8c/0x2a0
scsi_dma_map+0xc6/0x160
pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
scsi_queue_rq+0x79c/0x1200
blk_mq_dispatch_rq_list+0x4dc/0xb70
blk_mq_sched_dispatch_requests+0x249/0x310
__blk_mq_run_hw_queue+0x128/0x200
blk_mq_run_work_fn+0x27/0x30
process_one_work+0x522/0xa10
worker_thread+0x63/0x5b0
kthread+0x1d2/0x1f0
ret_from_fork+0x22/0x40
Fixes: b3aa14f022 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.
Switch hexagon to use generic version of these functions.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
to test and use this feature in the NTB transport layer. Also, bug
fixes for the AMD and Switchtec drivers, as well as some general
patches.
-----BEGIN PGP SIGNATURE-----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=P1lR
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.3' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@2000: 'clocks' is a required property
Add the missing 'clocks' properties to the examples to fix the errors.
Fixes: 2c9239c125 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
With the conversion to DT schema, the examples are now compiled with
dtc. The ad7124 binding example has the following warning:
Documentation/devicetree/bindings/iio/adc/adi,ad7124.example.dts:19.11-21: \
Warning (reg_format): /example-0/adc@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
There's a default #size-cells and #address-cells values of 1 for
examples. For examples needing different values such as this one on a
SPI bus, they need to provide a SPI bus parent node.
Fixes: 26ae15e62d ("Convert AD7124 bindings documentation to YAML format.")
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Now that examples are validated against the DT schema, a typo in
avia-hx711 example generates a warning:
Documentation/devicetree/bindings/iio/adc/avia-hx711.example.dt.yaml: weight: 'avdd-supply' is a required property
Fix the typo.
Fixes: 5150ec3fe1 ("avia-hx711.yaml: transform DT binding to YAML")
Cc: Andreas Klinger <ak@it-klinger.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The schema examples are now validated against the schema itself. The
AST2500 pinctrl schema has a couple of errors:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
example-0: $nodename:0: 'example-0' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
pinctrl: aspeed,external-nodes: [[1, 2]] is too short
Fixes: 0a617de167 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
The Aspeed pinctl schema have errors in the 'compatible' schema:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2400-pinctrl', 'aspeed', 'g4-pinctrl'] has non-unique elements
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2500-pinctrl', 'aspeed', 'g5-pinctrl'] has non-unique elements
Flow style sequences have to be quoted if the vales contain ','. Fix
this by using the more common one line per entry formatting.
Fixes: 0a617de167 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Fixes: 07457937bb ("dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-RiscV cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Risc-V CPU schema.
The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-spi@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull more input updates from Dmitry Torokhov:
- Apple SPI keyboard and trackpad driver for newer Macs
- ALPS driver will ignore trackpoint-only devices to give the
trackpoint driver a chance to handle them properly
- another Lenovo is switched over to SMbus from PS/2
- assorted driver fixups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - fix a mismatch between a condition check and its comment
Input: psmouse - fix build error of multiple definition
Input: applespi - remove set but not used variables 'sts'
Input: add Apple SPI keyboard and trackpad driver
Input: alps - don't handle ALPS cs19 trackpoint-only device
Input: hyperv-keyboard - remove dependencies on PAGE_SIZE for ring buffer
Input: adp5589 - initialize GPIO controller parent device
Input: iforce - remove empty multiline comments
Input: synaptics - fix misuse of strlcpy
Input: auo-pixcir-ts - switch to using devm_add_action_or_reset()
Input: gtco - bounds check collection indent level
Input: mtk-pmic-keys - add of_node_put() before return
Input: sun4i-lradc-keys - add of_node_put() before return
Input: synaptics - whitelist Lenovo T580 SMBus intertouch
Fix various regressions:
- force unencrypted dma-coherent buffers if encryption bit can't fit
into the dma coherent mask (Tom Lendacky)
- avoid limiting request size if swiotlb is not used (me)
- fix swiotlb handling in dma_direct_sync_sg_for_cpu/device
(Fugang Duan)
-----BEGIN PGP SIGNATURE-----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=Bv+Q
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions:
- force unencrypted dma-coherent buffers if encryption bit can't fit
into the dma coherent mask (Tom Lendacky)
- avoid limiting request size if swiotlb is not used (me)
- fix swiotlb handling in dma_direct_sync_sg_for_cpu/device (Fugang
Duan)"
* tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device
dma-direct: only limit the mapping size if swiotlb could be used
dma-mapping: add a dma_addressing_limited helper
dma-direct: Force unencrypted DMA under SME for certain DMA masks
Pull x86 fixes from Thomas Gleixner:
"A set of x86 specific fixes and updates:
- The CR2 corruption fixes which store CR2 early in the entry code
and hand the stored address to the fault handlers.
- Revert a forgotten leftover of the dropped FSGSBASE series.
- Plug a memory leak in the boot code.
- Make the Hyper-V assist functionality robust by zeroing the shadow
page.
- Remove a useless check for dead processes with LDT
- Update paravirt and VMware maintainers entries.
- A few cleanup patches addressing various compiler warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Prevent clobbering of saved CR2 value
x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
x86, boot: Remove multiple copy of static function sanitize_boot_params()
x86/boot/compressed/64: Remove unused variable
x86/boot/efi: Remove unused variables
x86/mm, tracing: Fix CR2 corruption
x86/entry/64: Update comments and sanity tests for create_gap
x86/entry/64: Simplify idtentry a little
x86/entry/32: Simplify common_exception
x86/paravirt: Make read_cr2() CALLEE_SAVE
MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
x86/process: Delete useless check for dead process with LDT
x86: math-emu: Hide clang warnings for 16-bit overflow
x86/e820: Use proper booleans instead of 0/1
x86/apic: Silence -Wtype-limits compiler warnings
x86/mm: Free sme_early_buffer after init
x86/boot: Fix memory leak in default_get_smp_config()
Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test
Pull perf tooling updates from Thomas Gleixner:
"A set of perf improvements and fixes:
perf db-export:
- Improvements in how COMM details are exported to databases for post
processing and use in the sql-viewer.py UI.
- Export switch events to the database.
BPF:
- Bump rlimit(MEMLOCK) for 'perf test bpf' and 'perf trace', just
like selftests/bpf/bpf_rlimit.h do, which makes errors due to
exhaustion of this limit, which are kinda cryptic (EPERM sometimes)
less frequent.
perf version:
- Fix segfault due to missing OPT_END(), noticed on PowerPC.
perf vendor events:
- Add JSON files for IBM s/390 machine type 8561.
perf cs-etm (ARM):
- Fix two cases of error returns not bing done properly: Invalid
ERR_PTR() use and loss of propagation error codes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
perf version: Fix segfault due to missing OPT_END()
perf vendor events s390: Add JSON files for machine type 8561
perf cs-etm: Return errcode in cs_etm__process_auxtrace_info()
perf cs-etm: Remove errnoeous ERR_PTR() usage in cs_etm__process_auxtrace_info
perf scripts python: export-to-postgresql.py: Export switch events
perf scripts python: export-to-sqlite.py: Export switch events
perf db-export: Export switch events
perf db-export: Factor out db_export__threads()
perf script: Add scripting operation process_switch()
perf scripts python: exported-sql-viewer.py: Use new 'has_calls' column
perf scripts python: exported-sql-viewer.py: Remove redundant semi-colons
perf scripts python: export-to-postgresql.py: Add has_calls column to comms table
perf scripts python: export-to-sqlite.py: Add has_calls column to comms table
perf db-export: Also export thread's current comm
perf db-export: Factor out db_export__comm()
perf scripts python: export-to-postgresql.py: Export comm details
perf scripts python: export-to-sqlite.py: Export comm details
perf db-export: Export comm details
perf db-export: Fix a white space issue in db_export__sample()
perf db-export: Move export__comm_thread into db_export__sample()
...
Pull core fixes from Thomas Gleixner:
- A collection of objtool fixes which address recent fallout partially
exposed by newer toolchains, clang, BPF and general code changes.
- Force USER_DS for user stack traces
[ Note: the "objtool fixes" are not all to objtool itself, but for
kernel code that triggers objtool warnings.
Things like missing function size annotations, or code that confuses
the unwinder etc. - Linus]
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
objtool: Support conditional retpolines
objtool: Convert insn type to enum
objtool: Fix seg fault on bad switch table entry
objtool: Support repeated uses of the same C jump table
objtool: Refactor jump table code
objtool: Refactor sibling call detection logic
objtool: Do frame pointer check before dead end check
objtool: Change dead_end_function() to return boolean
objtool: Warn on zero-length functions
objtool: Refactor function alias logic
objtool: Track original function across branches
objtool: Add mcsafe_handle_tail() to the uaccess safe list
bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()
x86/uaccess: Remove redundant CLACs in getuser/putuser error paths
x86/uaccess: Don't leak AC flag into fentry from mcsafe_handle_tail()
x86/uaccess: Remove ELF function annotation from copy_user_handle_tail()
x86/head/64: Annotate start_cpu0() as non-callable
x86/entry: Fix thunk function ELF sizes
x86/kvm: Don't call kvm_spurious_fault() from .fixup
x86/kvm: Replace vmx_vmenter()'s call to kvm_spurious_fault() with UD2
...
