In general when the consumer of a regulator requests that the
regulator be disabled it no longer will be drawing much load from the
regulator--it should just be the leakage current and that should be
very close to 0.
Up to this point the regulator framework has continued to count a
consumer's load request for disabled regulators. This has led to code
patterns that look like this:
enable_my_thing():
regular_set_load(reg, load_uA)
regulator_enable(reg)
disable_my_thing():
regulator_disable(reg)
regulator_set_load(reg, 0)
Sometimes disable_my_thing() sets a nominal (<= 100 uA) load instead
of setting a 0 uA load. I will make the assertion that nearly all (if
not all) places where we set a nominal load of 100 uA or less we end
up with a result that is the same as if we had set a load of 0 uA.
Specifically:
- The whole point of setting the load is to help set the operating
mode of the regulator. Higher loads may need less efficient
operating modes.
- The only time this matters at all is if there is another consumer of
the regulator that wants the regulator on. If there are no other
consumers of the regulator then the regulator will turn off and we
don't care about the operating mode.
- If there's another consumer that actually wants the regulator on
then presumably it is requesting a load that makes our nominal
<= 100 uA load insignificant.
A quick survey of the existing callers to regulator_set_load() to see
how everyone uses it:
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator core takes over managing the lifetime of the enable GPIO
once the regulator is registered. As such we shouldn't register the
enable GPIO using devm, or it will be freed twice.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "requested_microamps" sysfs attribute was only being exposed for
"current" regulators. This didn't make sense. Allow it to be exposed
always.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on review comments on the MFD driver, move the child drivers for
the Lochnagar MFD over to binding through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO descriptor array must be zero initialized to ensure that core will
properly handle also the case when no external GPIO pin is defined.
Fixes: 1c984942f0 ("regulator: s2mps11: Pass descriptor instead of GPIO number")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Redefine binding for regulator-coupled-max-spread property in a way that
max-spread values are defined per regulator couple instead of defining
single max-spread for the whole group of coupled regulators.
With that change the following regulators coupling configuration will be
possible:
regA: regulatorA {
regulator-coupled-with = <®B ®C>;
regulator-coupled-max-spread = <100000 300000>;
};
regB: regulatorB {
regulator-coupled-with = <®A ®C>;
regulator-coupled-max-spread = <100000 200000>;
};
regC: regulatorC {
regulator-coupled-with = <®A ®B>;
regulator-coupled-max-spread = <300000 200000>;
};
Note that the regulator-coupled-max-spread property does not have any
users yet, hence it's okay to change the binding.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's unlikely that regulators may disappear/appear while regulators
debug-summary is being prepared, but let's be consistent and avoid that
situation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check whether supply regulator is the couple to avoid infinite recursion
during of locking.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Wait/wound mutex shall be used in order to avoid lockups on locking of
coupled regulators.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up from the device tree configuration node.
Tested on Odroid U3 (with max77686 although not using any GPIOs
for regulators, so at least default paths are not broken).
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Cc: patches@opensource.cirrus.com
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Tested on Odroid XU3 (with s2mps11 although not using any GPIOs
for regulators, so at least default paths are not broken).
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD71837 and BD71847 have a HW functionality which leave power
rails OFF after powerof state:
- if they have been controlled by SW.
- if state transition from poweroff is done to SNVS
BD71837 can after reset transition from power-off to SNVS or
READY state depending on reset reason. By default only wathcdog
reset changes state from poweroff to ready. Change PMIC
configuration to always transition to READY in order to avoid
crucial power rails being OFF after reset.
If SNVS is required the crucial power rails should not be
controlled by SW - eg corresponding regulator control register
should have SEL bit kept zero. Currently the driver assumes all
regulators to be controlled by SW so it sets all SEL bits to 1.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The voltages in bd718xx_3rd_nodvs_buck_volts are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the according constraints for PM_SUSPEND_STANDBY case.
Previously, only suspend to mem/disk were taken into
consideration.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For state-mem and state-disk regulators can have
various parameters applied such as enabled/disabled,
current mode, voltage etc.
This patch adds documentation on how to set these parameters
in the device tree for the standby state.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators shall be uncoupled if one of the couples disappear.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On NVIDIA Tegra30 there is a requirement for regulator "A" to have voltage
higher than voltage of regulator "B" by N microvolts, the N value changes
depending on the voltage of regulator "B". This is similar to min-spread
between voltages of regulators, the difference is that the spread value
isn't fixed. This means that extra carefulness is required for regulator
"A" to drop its voltage without violating the requirement, hence its
voltage should be changed in steps so that its couple "B" could follow
(there is also max-spread requirement).
Add new "max_uV_step" constraint that breaks voltage change into several
steps, each step is limited by the max_uV_step value.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain hardware may require supply voltage to be changed in steps. Define
new property that allow to describe such hardware.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device tree binding was changed in a way that now max-spread values must
be defied per regulator pair. Limit number of pairs in order to adapt to
the new binding without changing regulators code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Redefine binding for regulator-coupled-max-spread property in a way that
max-spread values are defined per regulator couple instead of defining
single max-spread for the whole group of coupled regulators.
With that change the following regulators coupling configuration will be
possible:
regA: regulatorA {
regulator-coupled-with = <®B ®C>;
regulator-coupled-max-spread = <100000 300000>;
};
regB: regulatorB {
regulator-coupled-with = <®A ®C>;
regulator-coupled-max-spread = <100000 200000>;
};
regC: regulatorC {
regulator-coupled-with = <®A ®B>;
regulator-coupled-max-spread = <300000 200000>;
};
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't allow to get regulator until all of its couples resolved because
consumer will get EPERM and coupling shall be transparent for the drivers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If registered regulator found a couple, then the couple can find the
registered regulator too and hence coupling can be mutually resolved
at the registration time.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Uncoupled regulators should be a special case of coupled regulators, so
they should share a common voltage setting path. When enabling,
disabling or setting voltage of a coupled regulator, all coupled
regulators should be locked. Regulator's supplies should be locked, when
setting voltage of a single regulator. Enabling a coupled regulator or
setting its voltage should not be possible if some of its coupled
regulators, has not been registered.
Add function for locking coupled regulators and supplies. Extract
a new function regulator_set_voltage_rdev() from
regulator_set_voltage_unlocked(), which is called when setting
voltage of a single regulator.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Introduce new function regulator_balance_voltage(), which
keeps max_spread constraint fulfilled between a group of coupled
regulators. It should be called if a regulator changes its
voltage or after disabling or enabling. Disabled regulators should
follow changes of the enabled ones, but their consumers' demands
shouldn't be taken into account while calculating voltage of other
coupled regulators.
Find voltages, which are closest to suiting all the consumers' demands,
while fulfilling max_spread constraint, keeping the following rules:
- if one regulator is about to rise its voltage, rise others
voltages in order to keep the max_spread
- if a regulator, which has caused rising other regulators, is
lowered, lower other regulators if possible
- if one regulator is about to lower its voltage, but it hasn't caused
rising other regulators, change its voltage so that it doesn't break the
max_spread
Change regulators' voltages step by step, keeping max_spread constraint
fulfilled all the time. Function regulator_get_optimal_voltage()
should find the best possible change for the regulator, which doesn't
break max_spread constraint. In function regulator_balance_voltage()
optimize number of steps by finding highest voltage difference on
each iteration.
If a regulator, which is about to change its voltage, is not coupled,
method regulator_get_optimal_voltage() should simply return the lowest
voltage fulfilling consumers' demands.
Coupling should be checked only if the system is in PM_SUSPEND_ON state.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Review of the MFD component has stated we should not include the
register headers through lochnagar.h and thus removed them from that
header. Explicitly include them in the end drivers manually.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1:
drivers/regulator/bd718x7-regulator.c: In function ‘bd718xx_probe’:
drivers/regulator/bd718x7-regulator.c:1020: warning: initialization from incompatible pointer type
drivers/regulator/bd718x7-regulator.c:1024: warning: initialization from incompatible pointer type
Apparently this old compiler can't handle the obscure double
indirection.
However, there is no need for a double indirection. Just store a
pointer to the array instead, like other drivers tend to do.
Fixes: 494edd266b ("regulator/mfd: Support ROHM BD71847 power management IC")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently supports coin cell / super cap charging, so
this patch extends it to support PF0100.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Full filesystem authentication feature,
UBIFS is now able to have the whole filesystem structure
authenticated plus user data encrypted and authenticated.
- Minor cleanups
-----BEGIN PGP SIGNATURE-----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=lq2m
-----END PGP SIGNATURE-----
Merge tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Richard Weinberger:
- Full filesystem authentication feature, UBIFS is now able to have the
whole filesystem structure authenticated plus user data encrypted and
authenticated.
- Minor cleanups
* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
ubifs: Remove unneeded semicolon
Documentation: ubifs: Add authentication whitepaper
ubifs: Enable authentication support
ubifs: Do not update inode size in-place in authenticated mode
ubifs: Add hashes and HMACs to default filesystem
ubifs: authentication: Authenticate super block node
ubifs: Create hash for default LPT
ubfis: authentication: Authenticate master node
ubifs: authentication: Authenticate LPT
ubifs: Authenticate replayed journal
ubifs: Add auth nodes to garbage collector journal head
ubifs: Add authentication nodes to journal
ubifs: authentication: Add hashes to index nodes
ubifs: Add hashes to the tree node cache
ubifs: Create functions to embed a HMAC in a node
ubifs: Add helper functions for authentication support
ubifs: Add separate functions to init/crc a node
ubifs: Format changes for authentication support
ubifs: Store read superblock node
ubifs: Drop write_node
...
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
private struct, and a few bug fixes.
-----BEGIN PGP SIGNATURE-----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=EhpD
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.20' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Fairly minor changes and bug fixes:
NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
private struct, and a few bug fixes"
* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
ntb: idt: Alter the driver info comments
ntb: idt: Discard temperature sensor IRQ handler
ntb: idt: Add basic hwmon sysfs interface
ntb: idt: Alter temperature read method
ntb_netdev: Simplify remove with client device drvdata
NTB: transport: Try harder to alloc an aligned MW buffer
ntb: ntb_transport: Mark expected switch fall-throughs
ntb: idt: Set PCIe bus address to BARLIMITx
NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
ntb: intel: fix return value for ndev_vec_mask()
ntb_netdev: fix sleep time mismatch
Pull scheduler fixes from Ingo Molnar:
"A memory (under-)allocation fix and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Fix off by one bug
sched/rt: Update comment in pick_next_task_rt()
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
Pull perf updates and fixes from Ingo Molnar:
"These are almost all tooling updates: 'perf top', 'perf trace' and
'perf script' fixes and updates, an UAPI header sync with the merge
window versions, license marker updates, much improved Sparc support
from David Miller, and a number of fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
perf intel-pt/bts: Calculate cpumode for synthesized samples
perf intel-pt: Insert callchain context into synthesized callchains
perf tools: Don't clone maps from parent when synthesizing forks
perf top: Start display thread earlier
tools headers uapi: Update linux/if_link.h header copy
tools headers uapi: Update linux/netlink.h header copy
tools headers: Sync the various kvm.h header copies
tools include uapi: Update linux/mmap.h copy
perf trace beauty: Use the mmap flags table generated from headers
perf beauty: Wire up the mmap flags table generator to the Makefile
perf beauty: Add a generator for MAP_ mmap's flag constants
tools include uapi: Update asound.h copy
tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
tools include uapi: Update linux/fs.h copy
perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
perf cs-etm: Correct CPU mode for samples
perf unwind: Take pgoff into account when reporting elf to libdwfl
perf top: Do not use overwrite mode by default
perf top: Allow disabling the overwrite mode
perf trace: Beautify mount's first pathname arg
...
Pull irq fixes from Ingo Molnar:
"An irqchip driver fix and a memory (over-)allocation fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
irq/matrix: Fix memory overallocation
With the addition of the NUMA identity level, we increased @level by
one and will run off the end of the array in the distance sort loop.
Fixed: 051f3ca02e ("sched/topology: Introduce NUMA identity node sched domain")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A few fixes who have come in near or during the merge window:
- Removal of a VLA usage in Marvell mpp platform code
- Enable some IPMI options for ARM64 servers by default, helps testing
- Enable PREEMPT on 32-bit ARMv7 defconfig
- Minor fix for stm32 DT (removal of an unused DMA property)
- Bugfix for TI OMAP1-based ams-delta (-EINVAL -> IRQ_NOTCONNECTED)
-----BEGIN PGP SIGNATURE-----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=mr8i
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes who have come in near or during the merge window:
- Removal of a VLA usage in Marvell mpp platform code
- Enable some IPMI options for ARM64 servers by default, helps
testing
- Enable PREEMPT on 32-bit ARMv7 defconfig
- Minor fix for stm32 DT (removal of an unused DMA property)
- Bugfix for TI OMAP1-based ams-delta (-EINVAL -> IRQ_NOTCONNECTED)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: stm32: update HASH1 dmas property on stm32mp157c
ARM: orion: avoid VLA in orion_mpp_conf
ARM: defconfig: Update multi_v7 to use PREEMPT
arm64: defconfig: Enable some IPMI configs
soc: ti: QMSS: Fix usage of irq_set_affinity_hint
ARM: OMAP1: ams-delta: Fix impossible .irq < 0
- Fix W+X page (mark RO) allocated by the arm64 kprobes code
- Makefile fix for .i files in out of tree modules
-----BEGIN PGP SIGNATURE-----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=hH50
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- fix W+X page (mark RO) allocated by the arm64 kprobes code
- Makefile fix for .i files in out of tree modules
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kprobe: make page to RO mode when allocate it
arm64: kdump: fix small typo
arm64: makefile fix build of .i file in external module case
-----BEGIN PGP SIGNATURE-----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=Ilu6
-----END PGP SIGNATURE-----
Merge tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes and updates from Steve French:
"Three small fixes (one Kerberos related, one for stable, and another
fixes an oops in xfstest 377), two helpful debugging improvements,
three patches for cifs directio and some minor cleanup"
* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix signed/unsigned mismatch on aio_read patch
cifs: don't dereference smb_file_target before null check
CIFS: Add direct I/O functions to file_operations
CIFS: Add support for direct I/O write
CIFS: Add support for direct I/O read
smb3: missing defines and structs for reparse point handling
smb3: allow more detailed protocol info on open files for debugging
smb3: on kerberos mount if server doesn't specify auth type use krb5
smb3: add trace point for tree connection
cifs: fix spelling mistake, EACCESS -> EACCES
cifs: fix return value for cifs_listxattr
Pull 9p fix from Al Viro:
"Regression fix for net/9p handling of iov_iter; broken by braino when
switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: Fix 9p virtio breakage
