The i2cdetect uses the SMBus Quick command by default to scan devices
on the I2C bus. The FT260 implements an I2C bus controller. The SMBus
is derived from I2C, but there are several differences between the
specifications of the two buses in the areas of timing, protocols,
operation modes, and electrical characteristics.
One of the differences is that the I2C devices allow the slave not
to ACK its slave address, but SMBus requires it to always ACK it as
a mechanism to detect a detachable device’s presence on the bus.
Since FT260 is the I2C bus controller, it does not acknowledge the
SMBus Quick write command, which sends a single bit to the device at
the place of the RD/WR bit.
The ft260 driver attempted to mimic the SMBus Quick Write functionality
by writing a single byte as the SMBus Byte Write command does.
Usually, one byte in the SMBus Quick Write will be fine. However, it may
cause problems with devices with a control register at offset 0, like
i2c muxes, for example, when scanned with the i2cdetect utility.
The i2cdetect with the "-r" option uses the SMBus Read Byte command,
which is a reasonable workaround. To prevent the I2C bus from locking
at write-only devices (most notably clock chips at address 0x69), use
the "-r" option in conjunction with scanning range parameters.
This patch removes the SMBus Quick command support.
$ sudo i2cdetect -y 13
Warning: Can't use SMBus Quick Write command, will skip some addresses
0 1 2 3 4 5 6 7 8 9 a b c d e f
00:
10:
20:
30: -- -- -- -- -- -- -- --
40:
50: 50 51 -- -- -- -- -- -- -- -- -- -- -- -- -- --
60:
70:
$ sudo i2cdetect -y -r 13
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: 50 51 -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Reported-by: Vince Asbridge <VAsbridge@sanblaze.com>
Reported-by: Stephen Shirron <SShirron@sanblaze.com>
Reported-by: Enrik Berkhan <Enrik.Berkhan@inka.de>
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The FT260 is not supposed to generate unexpected HID reports. However,
in theory, the unsolicited HID Input reports can be issued by a specially
crafted malicious USB device masquerading as FT260 when the attacker has
physical access to the USB port. In this case, the read_buf pointer points
to the final data portion of the previous I2C Read transfer, and the memcpy
invoked in the ft260_raw_event() will try copying the content of the
unexpected report into the wrong location.
This commit sets the Read buffer pointer to NULL on the I2C Read
transaction completion and checks it in the ft260_raw_event() to detect
and skip the unsolicited Input report.
Reported-by: Enrik Berkhan <Enrik.Berkhan@inka.de>
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do not populate the /dev/hidraw on ft260 interfaces when the hid-ft260
driver is loaded.
$ sudo insmod hid-ft260.ko
$ ls /dev/hidraw*
/dev/hidraw0
$ sudo rmmod hid-ft260.ko
$ ls /dev/hidraw*
/dev/hidraw0 /dev/hidraw1 /dev/hidraw2
Reported-by: Enrik Berkhan <Enrik.Berkhan@inka.de>
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A random i2c read operation in EEPROM devices is implemented as a dummy
write operation, followed by a current address read operation. The dummy
write operation is used to load the target byte or word address (a.k.a
offset) into the offset counter, from which the subsequent read operation
then reads.
To support longer than one HID report size random read, the ft260 driver
issues multiple pairs of i2c write offset + read data transactions of HID
report size so that the EEPROM device sees many i2c random read requests
from different offsets.
Two issues with the current implementation:
- This approach suffers from extra overhead caused by writing offset
requests.
- Necessity to handle offset per HID report in big-endian representation
as EEPROM devices expect. The current implementation does not do it and
correctly handles the reads up to 60 bytes only.
This patch addresses both issues by implementing more efficient approach.
It issues a single i2c read request of up to the EEPROM page size and then
waits for the data to arrive in multiple HID reports. For example, to read
the 256 bytes from a 24LC512 chip, which has 128 bytes page size, the old
method performs six ft260_i2c_write_read transactions while the new - two
only.
Before:
$ sudo ./i2cperf -d 2 -o 2 -s 128 -r 0-0xff 13 0x51 -S
Read block via i2ctransfer by chunks
-------------------------------------------------------------------
data rate(bps) efficiency(%) data size(B) total IOs IO size(B)
-------------------------------------------------------------------
40803 85 256 2 128
Kernel log of a single 128 bytes read request:
[ +2.376308] ft260_i2c_write_read: read_off 0x0 left_len 128 len 60
[ +0.000002] ft260_i2c_write: rep 0xd0 addr 0x51 off 0 len 2 wlen 2 flag 0x2 d[0] 0x0
[ +0.000707] ft260_xfer_status: bus_status 0x41, clock 100
[ +0.000173] ft260_xfer_status: bus_status 0x40, clock 100
[ +0.000001] ft260_i2c_read: rep 0xc2 addr 0x51 len 60
[ +0.008660] ft260_raw_event: i2c resp: rep 0xde len 60
[ +0.000156] ft260_xfer_status: bus_status 0x20, clock 100
[ +0.000001] ft260_i2c_write_read: read_off 0x3c left_len 68 len 60
[ +0.000001] ft260_i2c_write: rep 0xd0 addr 0x51 off 0 len 2 wlen 2 flag 0x2 d[0] 0x3c
[ +0.001034] ft260_xfer_status: bus_status 0x41, clock 100
[ +0.000191] ft260_xfer_status: bus_status 0x40, clock 100
[ +0.000001] ft260_i2c_read: rep 0xc2 addr 0x51 len 60
[ +0.008614] ft260_raw_event: i2c resp: rep 0xde len 60
[ +0.000203] ft260_xfer_status: bus_status 0x20, clock 100
[ +0.000001] ft260_i2c_write_read: read_off 0x78 left_len 8 len 8
[ +0.000001] ft260_i2c_write: rep 0xd0 addr 0x51 off 0 len 2 wlen 2 flag 0x2 d[0] 0x78
[ +0.000987] ft260_xfer_status: bus_status 0x41, clock 100
[ +0.000192] ft260_xfer_status: bus_status 0x40, clock 100
[ +0.000001] ft260_i2c_read: rep 0xc2 addr 0x51 len 8
[ +0.002614] ft260_raw_event: i2c resp: rep 0xd1 len 8
[ +0.000200] ft260_xfer_status: bus_status 0x20, clock 100
After:
$ sudo ./i2cperf -d 2 -o 2 -s 128 -r 0-0xff 13 0x51 -S
Read block via i2ctransfer by chunks
-------------------------------------------------------------------
data rate(bps) efficiency(%) data size(B) total IOs IO size(B)
-------------------------------------------------------------------
43990 85 256 2 128
Kernel log of a single 128 bytes read request:
[ +1.464346] ft260_i2c_write_read: off 0x0 rlen 128 wlen 2
[ +0.000002] ft260_i2c_write: rep 0xd0 addr 0x51 off 0 len 2 wlen 2 flag 0x2 d[0] 0x0
[ +0.001653] ft260_xfer_status: bus_status 0x41, clock 100
[ +0.000188] ft260_xfer_status: bus_status 0x40, clock 100
[ +0.000002] ft260_i2c_read: rep 0xc2 addr 0x51 len 128 rlen 60 flag 0x3
[ +0.008609] ft260_raw_event: i2c resp: rep 0xde len 60
[ +0.000157] ft260_xfer_status: bus_status 0x40, clock 100
[ +0.000002] ft260_i2c_read: rep 0xc2 addr 0x51 len 68 rlen 60 flag 0x0
[ +0.008840] ft260_raw_event: i2c resp: rep 0xde len 60
[ +0.000203] ft260_xfer_status: bus_status 0x40, clock 100
[ +0.000002] ft260_i2c_read: rep 0xc2 addr 0x51 len 8 rlen 8 flag 0x4
[ +0.002794] ft260_raw_event: i2c resp: rep 0xd1 len 8
[ +0.000201] ft260_xfer_status: bus_status 0x20, clock 100
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Tested-by: Guillaume Champagne <champagne.guillaume.c@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To support longer than one HID report size write, the driver splits a
single i2c message data payload into multiple i2c messages of HID report
size. However, it does not replicate the offset bytes within the EEPROM
chip in every consequent HID report because it is not and should not be
aware of the EEPROM type. It breaks the i2c write message integrity and
causes the EEPROM device not to acknowledge the second HID report keeping
the i2c bus busy until the ft260 controller reports failure.
This patch preserves the i2c write message integrity by manipulating the
i2c flag bits across multiple HID reports to be seen by the EEPROM device
as a single i2c write transfer.
Before:
$ sudo ./i2cperf -f 2 -o 2 -s 64 -r 0-0xff 13 0x51 -S
Error: Sending messages failed: Input/output error
[ +3.667741] ft260_i2c_write: rep 0xde addr 0x51 off 0 len 60 d[0] 0x0
[ +0.007330] ft260_hid_output_report_check_status: wait 6400 usec, len 64
[ +0.000203] ft260_xfer_status: bus_status 0x40, clock 100
[ +0.000001] ft260_i2c_write: rep 0xd1 addr 0x51 off 60 len 6 d[0] 0x0
[ +0.002337] ft260_hid_output_report_check_status: wait 1000 usec, len 10
[ +0.000157] ft260_xfer_status: bus_status 0x2e, clock 100
[ +0.000241] ft260_i2c_reset: done
[ +0.000003] ft260_i2c_write: failed to start transfer, ret -5
After:
$ sudo ./i2cperf -f 2 -o 2 -s 128 -r 0-0xff 13 0x51 -S
Fill block with increment via i2ctransfer by chunks
-------------------------------------------------------------------
data rate(bps) efficiency(%) data size(B) total IOs IO size(B)
-------------------------------------------------------------------
71260 86 256 2 128
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Tested-by: Guillaume Champagne <champagne.guillaume.c@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After clarifying with FTDI's support, it turned out that the error
condition (bit 1) in byte 1 of the i2c status HID report is a status
bit reflecting all error conditions. When bits 2, 3, or 4 are raised
to 1, bit 1 is set to 1 also. Since the ft260_xfer_status routine tests
the error condition bit and exits in the case of an error, the program
flow never reaches the conditional expressions for 2, 3, and 4 bits when
any of them indicates an error state. Though these expressions are never
evaluated to true, they are checked several times per IO, increasing the
ft260_xfer_status polling cycle duration.
The patch removes the conditional expressions for 2, 3, and 4 bits in
byte 1 of the i2c status HID report.
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Tested-by: Guillaume Champagne <champagne.guillaume.c@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the DualShock4 dongle in a very similar
way we contributed to hid-sony before.
The dongle is a USB to Bluetooth bridge and uses the same HID reports
as a USB device. It reports data through the DS4's main USB input
report independent on whether a Bluetooth controller is connected.
For this reason there is custom dongle report parsing code to
detect controller hotplug and kick of calibration work until we
are ready to process actual input reports.
The logic also incorporates a workaround needed for Steam in which
hid-playstation and Steam using hidraw can fight.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The poll interval for DualShock4 in Bluetooth mode is adjustable
through the main output report. Configure it to 4ms, which is
similar to USB.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for DualShock4 in Bluetooth mode. In Bluetooth, the device
is a bit strange in that after 'calibration' it switches sending all its
input data from a basic report (only containing buttons/sticks) to an
extended report, which also contains touchpad, motion sensors and other
data. The overall design of this code is similar to the DualSense code.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a parameter to ps_get_report to ignore CRC checks.
This prepares for DualShock4, which has some HID reports, which lack CRC.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Expose the lightbar LEDs in the same manner as hid-sony through
individual LEDs for backwards compatibility reasons. There is a
slight change in LED naming to use the input device name as opposed
to the MAC address like hid-sony did. This is expected to not
cause any issues and should make the naming more compliant.
In addition set a default lightbar color based on player ID.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the max_brightness adjustable through ps_led_info struct. This
paves the way for a next DualShock4 patch to allow larger brightness
values.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements DualShock4 rumble support in a similar manner
as the DualSense implementation. It adds an output worker with
granular control of different features of the main DualShock4 output
report.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Support accelerometer and gyroscope as separate input devices similar
how DualSense and hid-sony do it.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Support the DualShock4 touchpad as a separate input device. The code
describes the touchpad input reports through structures similar a bit
to the DualSense code.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Provide DualShock4 battery support through powersupply framework.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report DualShock4 hardware and firmware version info through sysfs.
It uses the same sysfs nodes as the DualSense did (and hid-sony).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add basic support for DualShock4 USB controller with buttons and sticks.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco LW is a UGEE v2 device with a frame with 8 buttons.
Its pen has 2 buttons, supports tilt and pressure.
It can be connected by USB cable or using a USB Bluetooth dongle to use
it in wireless mode. When it is connected using the dongle, the device
battery is used to power it.
Its vendor, product and version are identical to the Deco L. The only
difference reported by its firmware is the product name.
In order to add support for battery reporting, add a new HID descriptor
and a quirk to detect the wireless version of the tablet.
Link: https://github.com/DIGImend/digimend-kernel-drivers/issues/635
Tested-by: Mia Kanashi <chad@redpilled.dev>
Tested-by: Andreas Grosse <andig.mail@t-online.de>
Tested-by: Mia Kanashi <chad@redpilled.dev>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco LW drawing tablet can be connected by USB cable or using
a USB Bluetooth dongle. When it is connected using the dongle, there
might be a small delay until the tablet is paired with the dongle.
Fetching the device battery during this delay results in random battery
percentage values.
Add a quirk to avoid actively querying the battery percentage and wait
for the device to report it on its own.
Reported-by: Mia Kanashi <chad@redpilled.dev>
Tested-by: Mia Kanashi <chad@redpilled.dev>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds support for the turntable extension for Wiimote devices.
jstest-gtk and html5 gamepad tester show everything correctly
but when trying to map the controller in software like rpcs3 or dolphin
it currently doesn't map correctly
Co-authored-by: Bogdan Petru <thonkdifferent@outlook.com>
Signed-off-by: Bogdan Petru <thonkdifferent@outlook.com>
Signed-off-by: Joshua Jun <joshuajun@vivaldi.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support was added for devices using an explicit 3rd barrel switch,
the logic used by devices emulating this feature was broken. The 'if'
statement / block that was introduced only handles the case where the
button is pressed (i.e. 'barrelswitch' and 'barrelswitch2' are both set)
but not the case where it is released (i.e. one or both being cleared).
This results in a BTN_STYLUS3 "down" event being sent when the button
is pressed, but no "up" event ever being sent afterwards.
This patch restores the previously-used logic for determining button
states in the emulated case so that switches are reported correctly
again.
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/292
Fixes: 6d09085b38 ("HID: wacom: Adding Support for new usages")
CC: stable@vger.kernel.org #v5.19+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If hid_add_device() returns error, it should call hid_destroy_device()
to free hid_dev which is allocated in hid_allocate_device().
Fixes: 74c4fb0580 ("HID: hv_mouse: Properly add the hid device")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Variable count is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The iso_layout parameter must be manually set to get the driver to
swap KEY_102ND and KEY_GRAVE. This patch eliminates the need to do that.
This is safe to do, as Macs with keyboards that do not need the quirk
will keep working the same way as the value of hid->country will be
different than HID_COUNTRY_INTERNATIONAL_ISO. This was tested by one
person with a Mac with the WELLSPRINGT2_J152F keyboard with a layout
that does not require the quirk to be set.
Signed-off-by: Kerem Karabay <kekrby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-apple driver does not support chaining translations or
dependencies on other translations. This creates two problems:
1 - In Non-English keyboards of Macs, KEY_102ND and KEY_GRAVE are
swapped and the APPLE_ISO_TILDE_QUIRK is used to work around this
problem. The quirk is not set for the Macs where these bugs happen yet
(see the 2nd patch for that), but this can be forced by setting the
iso_layout parameter. Unfortunately, this only partially works.
KEY_102ND gets translated to KEY_GRAVE, but KEY_GRAVE does not get
translated to KEY_102ND, so both of them end up functioning as
KEY_GRAVE. This is because the driver translates the keys as if Fn was
pressed and the original is sent if it is not pressed, without any
further translations happening on the key[#463]. KEY_GRAVE is present at
macbookpro_no_esc_fn_keys[#195], so this is what happens:
- KEY_GRAVE -> KEY_ESC (as if Fn is pressed)
- KEY_GRAVE is returned (Fn isn't pressed, so translation is discarded)
- KEY_GRAVE -> KEY_102ND (this part is not reached!)
...
2 - In case the touchbar does not work, the driver supports sending
Escape when Fn+KEY_GRAVE is pressed. As mentioned previously, KEY_102ND
is actually KEY_GRAVE and needs to be translated before this happens.
Normally, these are the steps that should happen:
- KEY_102ND -> KEY_GRAVE
- KEY_GRAVE -> KEY_ESC (Fn is pressed)
- KEY_ESC is returned
Though this is what happens instead, as dependencies on other
translations are not supported:
- KEY_102ND -> KEY_ESC (Fn is pressed)
- KEY_ESC is returned
This patch fixes both bugs by ordering the translations correctly and by
making the translations continue and not return immediately after
translating a key so that chained translations work and translations can
depend on other ones.
This patch also simplifies the implementation of the swap_fn_leftctrl
option a little bit, as it makes it simply use a normal translation
instead adding extra code to translate a key to KEY_FN[#381]. This change
wasn't put in another patch as the code that translates the Fn key needs
to be changed because of the changes in the patch, and those changes
would be discarded with the next patch anyway (the part that originally
translates KEY_FN to KEY_LEFTCTRL needs to be made an else-if branch of
the part that transltes KEY_LEFTCTRL to KEY_FN).
Note: Line numbers (#XYZ) are for drivers/hid/hid-apple.c at commit
20afcc4625 ("HID: apple: Add "GANSS" to the non-Apple list").
Note: These bugs are only present on Macs with a keyboard with no
dedicated escape key and a non-English layout.
Signed-off-by: Kerem Karabay <kekrby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
struct synthhid_msg was meant to be a generic representation of the
possible protocol messages sent through VMBus. In practice, only the
header is read and depending on the message type, a cast to the actual
type is done. Also, SYNTHHID_MAX_INPUT_REPORT_SIZE constant isn't used
which I suspect is a leftover from the refactoring made while this
driver was at the staging folder.
This patch removes struct synthhid_msg and refactor the code
accordingly.
Signed-off-by: Paulo Miguel Almeida <paulo.miguel.almeida.rodenas@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----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=QU4t
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2022102101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- a 12 year old bug fix for the Apple Magic Trackpad v1 (José Expósito)
- a fix for a potential crash on removal of the Playstation controllers
(Roderick Colenbrander)
- a few new device IDs and device-specific quirks, most notably support
of the new Playstation DualSense Edge controller
* tag 'for-linus-2022102101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: lenovo: Make array tp10ubkbd_led static const
HID: saitek: add madcatz variant of MMO7 mouse device ID
HID: playstation: support updated DualSense rumble mode.
HID: playstation: add initial DualSense Edge controller support
HID: playstation: stop DualSense output work on remove.
HID: magicmouse: Do not set BTN_MOUSE on double report
Singular #ifdef IS_REACHABLE(CONFIG_GPIOLIB) weren't covering all the
gpiolib functions that were being referenced.
Update the code regions that are commented out when CONFIG_GPIOLIB isn't
enabled to avoid errors.
Fixes: 960f9df7c6 ("HID: mcp2221: add ADC/DAC support via iio subsystem")
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use (__force __le16) cast for adc_values le16_to_cpu conversion to correct following sparse
warnings:
drivers/hid/hid-mcp2221.c:950:32: sparse: sparse: cast to restricted __le16
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 960f9df7c6 ("HID: mcp2221: add ADC/DAC support via iio subsystem")
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In mcp2221_raw_event(), 'tmp' is used only conditionally. Move
the declaration into the conditional block in order to prevent
unused variable warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 960f9df7c6 ("HID: mcp2221: add ADC/DAC support via iio subsystem")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With the changes to the driver core to make more pointers const, the USB
subsystem also needs to be modified to take a const * for the devnode
callback so that the driver core's constant pointer will also be
properly propagated.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/20221001165128.2688526-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All these drivers have an i2c probe function which doesn't use the
"struct i2c_device_id *id" parameter, so they can trivially be
converted to the "probe_new" style of probe with a single argument.
This is part of an ongoing transition to single-argument i2c probe
functions. Old-style probe functions involve a call to i2c_match_id:
in drivers/i2c/i2c-core-base.c,
/*
* When there are no more users of probe(),
* rename probe_new to probe.
*/
if (driver->probe_new)
status = driver->probe_new(client);
else if (driver->probe)
status = driver->probe(client,
i2c_match_id(driver->id_table, client));
else
status = -EINVAL;
Drivers which don't need the second parameter can be declared using
probe_new instead, avoiding the call to i2c_match_id. Drivers which do
can still be converted to probe_new-style, calling i2c_match_id
themselves (as is done currently for of_match_id).
This change was done using the following Coccinelle script, and fixed
up for whitespace changes:
@ rule1 @
identifier fn;
identifier client, id;
@@
- static int fn(struct i2c_client *client, const struct i2c_device_id *id)
+ static int fn(struct i2c_client *client)
{
...when != id
}
@ rule2 depends on rule1 @
identifier rule1.fn;
identifier driver;
@@
struct i2c_driver driver = {
- .probe
+ .probe_new
=
(
fn
|
- &fn
+ fn
)
,
};
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for 3x 10-bit ADC and 1x DAC channels registered via the iio
subsystem.
To prevent breakage and unexpected dependencies this support only is
only built if CONFIG_IIO is enabled, and is only weakly referenced by
'imply IIO' within the respective Kconfig.
Additionally the iio device only gets registered if at least one channel
is enabled in the power-on configuration read from SRAM.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To avoid recursive dependencies on GPIOLIB when 'imply IIO' is requested
with other drivers we should switch GPIOLIB to an imply.
This isn't the most ideal solution but avoids modifiying the Kconfig for
other drivers, and only requires a singular IS_REACHABLE(CONFIG_GPIOLIB)
check.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch from i2c_add_adapter() to resource managed devm_i2c_add_adapter()
for matching rest of driver initialization, and more concise code.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One-element arrays are deprecated, and we are replacing them with
flexible array members instead. So, replace one-element array with
flexible-array member in structs synthhid_msg, synthhid_input_report,
pipe_prt_msg and refactor the rest of the code accordingly.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/210
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=101836 [1]
Signed-off-by: Paulo Miguel Almeida <paulo.miguel.almeida.rodenas@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't populate the read-only array tp10ubkbd_led on the stack but instead
make it static const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MadCatz variant of the MMO7 mouse has the ID 0738:1713 and the same
quirks as the Saitek variant.
Signed-off-by: Samuel Bailey <samuel.bailey1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Newer DualSense firmware supports a revised classic rumble mode,
which feels more similar to rumble as supported on previous PlayStation
controllers. It has been made the default on PlayStation and non-PlayStation
devices now (e.g. iOS and Windows). Default to this new mode when
supported.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20221010212313.78275-4-roderick.colenbrander@sony.com
Provide initial support for the DualSense Edge controller. The brings
support up to the level of the original DualSense, but won't yet provide
support for new features (e.g. reprogrammable buttons).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
CC: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20221010212313.78275-3-roderick.colenbrander@sony.com
Ensure we don't schedule any new output work on removal and wait
for any existing work to complete. If we don't do this e.g. rumble
work can get queued during deletion and we trigger a kernel crash.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
CC: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20221010212313.78275-2-roderick.colenbrander@sony.com
Under certain conditions the Magic Trackpad can group 2 reports in a
single packet. The packet is split and the raw event function is
invoked recursively for each part.
However, after processing each part, the BTN_MOUSE status is updated,
sending multiple click events. [1]
Return after processing double reports to avoid this issue.
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/811 # [1]
Fixes: a462230e16 ("HID: magicmouse: enable Magic Trackpad support")
Reported-by: Nulo <git@nulo.in>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20221009182747.90730-1-jose.exposito89@gmail.com
- a new driver for IBM Operational Panel
- a new driver for PinePhone keyboards
- RT5120 PMIC power key support
- various enhancements and support for new models in xpad (Xbox) driver
- a new compatible ID for Elan touchscreen driver
- rework of adp5588-keys driver to support configuring via device
properties (OF, ACPI, etc) instead of platform data, and proper support
of optional gpiochip functionality (and removal of gpio-adp5588 driver)
- improvements to firmware update handling in Synaptics RMI4 driver
- support for double key matrix in mt6779-keypad
- support for polled mode in adc-joystick driver
- other assorted driver fixes, cleanups and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCY0O9YwAKCRBAj56VGEWX
nICKAQD6/pS5tIWFCyYrM/A0xbkYuPWtmXqJTSGANlevU7nypwEAqaH2tYSDAdxM
NylDCPvvduHVmA2ewXgvIlUzjCLr6As=
=cUmW
-----END PGP SIGNATURE-----
Merge tag 'input-for-v6.1-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for IBM Operational Panel
- a new driver for PinePhone keyboards
- RT5120 PMIC power key support
- various enhancements and support for new models in xpad (Xbox) driver
- a new compatible ID for Elan touchscreen driver
- rework of adp5588-keys driver to support configuring via device
properties (OF, ACPI, etc) instead of platform data, and proper
support of optional gpiochip functionality (and removal of
gpio-adp5588 driver)
- improvements to firmware update handling in Synaptics RMI4 driver
- support for double key matrix in mt6779-keypad
- support for polled mode in adc-joystick driver
- other assorted driver fixes, cleanups and improvements
* tag 'input-for-v6.1-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (90 commits)
Input: i8042 - fix refount leak on sparc
Input: i8042 - add LoongArch support in i8042-acpipnpio.h
Input: i8042 - rename i8042-x86ia64io.h to i8042-acpipnpio.h
Input: pinephone-keyboard - support the proxied I2C bus
Input: pinephone-keyboard - add PinePhone keyboard driver
dt-bindings: input: Add the PinePhone keyboard binding
dt-bindings: input: Convert hid-over-i2c to DT schema
input: drop empty comment blocks
Input: xpad - add X-Box Adaptive Profile button
Input: add ABS_PROFILE to uapi and documentation
Input: xpad - add X-Box Adaptive XBox button
Input: xpad - add X-Box Adaptive support
Input: ims-pcu - fix spelling mistake "BOOLTLOADER" -> "BOOTLOADER"
Input: ibm-panel - add missing MODULE_DEVICE_TABLE
Input: icn8505 - utilize acpi_get_subsystem_id()
Input: xpad - decipher xpadone packages with GIP defines
Input: xpad - refactor using BIT() macro
Input: synaptics-rmi4 - convert to use sysfs_emit() APIs
Input: twl4030-pwrbutton - add missing of.h include
Input: applespi - replace zero-length array with DECLARE_FLEX_ARRAY() helper
...
-----BEGIN PGP SIGNATURE-----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=lo26
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2022100501' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- handle of all Logitech Bluetooth HID++ devices in the Logitech HID++
drivers (Bastien Nocera)
- fix broken atomic checks in hid-multitouch by adding memory barriers
(Andri Yngvason)
- better handling of devices with AMD SFH1.1 (Basavaraj Natikar)
- better support of Nintendo clone controllers (Icenowy Zheng and
Johnothan King)
- Support for various RC controllers (Marcus Folkesson)
- Add UGEEv2 support in hid-uclogic (XP-PEN Deco Pro S and Parblo A610
PRO) (José Expósito)
- some conversions to use dev_groups (Greg Kroah-Hartman)
- HID-BPF preparatory patches, mostly to convert blank defines as enums
(Benjamin Tissoires)
* tag 'for-linus-2022100501' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (38 commits)
HID: wacom: add three styli to wacom_intuos_get_tool_type
HID: amd_sfh: Handle condition of "no sensors" for SFH1.1
HID: amd_sfh: Change dev_err to dev_dbg for additional debug info
HID: nintendo: check analog user calibration for plausibility
HID: nintendo: deregister home LED when it fails
HID: roccat: Fix use-after-free in roccat_read()
hid: topre: Add driver fixing report descriptor
HID: multitouch: Add memory barriers
HID: convert defines of HID class requests into a proper enum
HID: export hid_report_type to uapi
HID: core: store the unique system identifier in hid_device
HID: Add driver for PhoenixRC Flight Controller
HID: Add driver for VRC-2 Car Controller
HID: sony: Fix double word in comments
hid: hid-logitech-hidpp: avoid unnecessary assignments in hidpp_connect_event
HID: logitech-hidpp: Detect hi-res scrolling support
HID: logitech-hidpp: Remove hard-coded "Sw. Id." for HID++ 2.0 commands
HID: logitech-hidpp: Fix "Sw. Id." for HID++ 2.0 commands
HID: logitech-hidpp: Remove special-casing of Bluetooth devices
HID: logitech-hidpp: Enable HID++ for all the Logitech Bluetooth devices
...
We forgot to add the 3D pen ID a year ago. There are two new pro pen
IDs to be added.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on num_hid_devices, each sensor device registers to HID. If
"no sensors" then amd_sfh work initialization and scheduling
doesn’t make sense and return ENODEV to stop driver probe.
Hence add a check for num_hid_devices to handle special
case in the situation of "no sensors" for SFH1.1.
Fixes: 93ce5e0231 ("HID: amd_sfh: Implement SFH1.1 functionality")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Users should only be notified at most one time on systems doesn't have
any sensors connected or non-supported systems.
Check the return code and don't display error messages in those
conditions.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Define new ABS_PROFILE axis for input devices which need it, e.g. X-Box
Adaptive Controller and X-Box Elite 2.
Signed-off-by: Nate Yocom <nate@yocom.org>
Link: https://lore.kernel.org/r/20220908173930.28940-4-nate@yocom.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Arne Wendt writes:
Cheap clone controllers may (falsely) report as having a user
calibration for the analog sticks in place, but return
wrong/impossible values for the actual calibration data.
In the present case at mine, the controller reports having a
user calibration in place and successfully executes the read
commands. The reported user calibration however is
min = center = max = 0.
This pull request addresses problems of this kind by checking the
provided user calibration-data for plausibility (min < center < max)
and falling back to the default values if implausible.
I'll note that I was experiencing a crash because of this bug when using
the GuliKit KingKong 2 controller. The crash manifests as a divide by
zero error in the kernel logs:
kernel: divide error: 0000 [#1] PREEMPT SMP NOPTI
Link: https://github.com/nicman23/dkms-hid-nintendo/pull/25
Link: https://github.com/DanielOgorchock/linux/issues/36
Co-authored-by: Arne Wendt <arne.wendt@tuhh.de>
Signed-off-by: Johnothan King <johnothanking@protonmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/gvpL2G6VwXGJPvxX5KRiu9pVjvTivgayug_jdKDY6zfuAaAqncP9BkKLosjwUXNlgVVTMfJSKfwPF1K79cKAkwGComyC21vCV3q9B3EXNkE=@protonmail.com
Some Pro Controller compatible controllers do not support home LED, and
will fail when setting it. Currently this leads to probe failure.
Change the code that fails probing to deregistering home LED.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Reviewed-by: Silvan Jegen <s.jegen@gmail.com>
[bentiss: changed "dflt" to "default"]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220415100432.23453-1-icenowy@aosc.io
roccat_report_event() is responsible for registering
roccat-related reports in struct roccat_device.
int roccat_report_event(int minor, u8 const *data)
{
struct roccat_device *device;
struct roccat_reader *reader;
struct roccat_report *report;
uint8_t *new_value;
device = devices[minor];
new_value = kmemdup(data, device->report_size, GFP_ATOMIC);
if (!new_value)
return -ENOMEM;
report = &device->cbuf[device->cbuf_end];
/* passing NULL is safe */
kfree(report->value);
...
The registered report is stored in the struct roccat_device member
"struct roccat_report cbuf[ROCCAT_CBUF_SIZE];".
If more reports are received than the "ROCCAT_CBUF_SIZE" value,
kfree() the saved report from cbuf[0] and allocates a new reprot.
Since there is no lock when this kfree() is performed,
kfree() can be performed even while reading the saved report.
static ssize_t roccat_read(struct file *file, char __user *buffer,
size_t count, loff_t *ppos)
{
struct roccat_reader *reader = file->private_data;
struct roccat_device *device = reader->device;
struct roccat_report *report;
ssize_t retval = 0, len;
DECLARE_WAITQUEUE(wait, current);
mutex_lock(&device->cbuf_lock);
...
report = &device->cbuf[reader->cbuf_start];
/*
* If report is larger than requested amount of data, rest of report
* is lost!
*/
len = device->report_size > count ? count : device->report_size;
if (copy_to_user(buffer, report->value, len)) {
retval = -EFAULT;
goto exit_unlock;
}
...
The roccat_read() function receives the device->cbuf report and
delivers it to the user through copy_to_user().
If the N+ROCCAT_CBUF_SIZE th report is received while copying of
the Nth report->value is in progress, the pointer that copy_to_user()
is working on is kfree()ed and UAF read may occur. (race condition)
Since the device node of this driver does not set separate permissions,
this is not a security vulnerability, but because it is used for
requesting screen display of profile or dpi settings,
a user using the roccat device can apply udev to this device node or
There is a possibility to use it by giving.
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Topre REALFORCE R2 firmware incorrectly reports that interface
descriptor number 1, input report descriptor 2's events are array events
rather than variable events. That particular report descriptor is used
to report keypresses when there are more than 6 keys held at a time.
This bug prevents events from this interface from being registered
properly, so only 6 keypresses (from a different interface) can be
registered at once, rather than full n-key rollover.
This commit fixes the bug by setting the correct value in a report_fixup
function.
The original bug report can be found here:
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/804
Thanks to Benjamin Tissoires for diagnosing the issue with the report
descriptor.
Signed-off-by: Harry Stern <harry@harrystern.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220911003614.297613-1-harry@harrystern.net
This fixes broken atomic checks which cause a race between the
release-timer and processing of hid input.
I noticed that contacts were sometimes sticking, even with the "sticky
fingers" quirk enabled. This fixes that problem.
Cc: stable@vger.kernel.org
Fixes: 9609827458 ("HID: multitouch: optimize the sticky fingers timer")
Signed-off-by: Andri Yngvason <andri@yngvason.is>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220907150159.2285460-1-andri@yngvason.is
This allows to export the type in BTF and so in the automatically
generated vmlinux.h. It will also add some static checks on the users
when we change the ll driver API (see not below).
Note that we need to also do change in the ll_driver API, but given
that this will have a wider impact outside of this tree, we leave this
as a TODO for the future.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220902132938.2409206-11-benjamin.tissoires@redhat.com
When we are dealing with eBPF, we need to have access to the report type.
Currently our implementation differs from the USB standard, making it
impossible for users to know the exact value besides hardcoding it
themselves.
And instead of a blank define, convert it as an enum.
Note that we need to also do change in the ll_driver API, but given
that this will have a wider impact outside of this tree, we leave this
as a TODO for the future.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220902132938.2409206-10-benjamin.tissoires@redhat.com
This unique identifier is currently used only for ensuring uniqueness in
sysfs. However, this could be handful for userspace to refer to a specific
hid_device by this id.
2 use cases are in my mind: LEDs (and their naming convention), and
HID-BPF.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220902132938.2409206-9-benjamin.tissoires@redhat.com
hidpp->delayed_input can't be assigned to an object that already call
input_free_device when input_register_device fails.
Fixes: c39e3d5fc9 ("HID: logitech-hidpp: late bind the input device on wireless connection")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220812025515.19467-1-hbh25y@gmail.com
Rather than relying on a never-ending stream of patches for quirks.
This change will detect whether HID++ 1.0 hi-res scroll, HID++ 2.0
hi-res scroll or HID++ 2.0 hi-res scroll wheel is supported, and enable
the feature without the need for quirks.
Tested on a Logitech M705 mouse that was unsupported before this change.
[ 9.365324] logitech-hidpp-device 0003:046D:406D.0006: input,hidraw3: USB HID v1.11 Mouse [Logitech M705] on usb-0000:00:14.0-4/input2:3
[ 57.472434] logitech-hidpp-device 0003:046D:406D.0006: HID++ 4.5 device connected.
[ 57.616429] logitech-hidpp-device 0003:046D:406D.0006: Detected HID++ 2.0 hi-res scroll wheel
[ 57.712424] logitech-hidpp-device 0003:046D:406D.0006: wheel multiplier = 8
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216480
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Tested-by: Peter F. Patel-Schneider <pfpschneider@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220914132146.6435-1-hadess@hadess.net
Some HID++ 2.0 commands had correctly set a non-zero software identifier
directly as part of their function identifiers, but it's more correct to
define the function identifier and the software identifier separately
before combined them when the command is sent.
As this is now done in the previous commit, remove the hard-coded 0x1
software identifiers in the function definitions.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Always set a non-zero "Sw. Id." in the lower nibble of the Function/ASE
and Software Identifier byte in HID++ 2.0 commands.
As per the "Protocol HID++2.0 essential features" section in
https://lekensteyn.nl/files/logitech/logitech_hidpp_2.0_specification_draft_2012-06-04.pdf
"
Software identifier (4 bits, unsigned)
A number uniquely defining the software that sends a request. The
firmware must copy the software identifier in the response but does
not use it in any other ways.
0 Do not use (allows to distinguish a notification from a response).
"
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215699
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that all the Logitech Bluetooth devices are probed for HID++
support, remove the handling of those 2 devices without any quirks, as
they're duplicates.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Probe for HID++ support over Bluetooth for all the Logitech Bluetooth
devices. As Logitech doesn't have a list of Bluetooth devices that
support HID++ over Bluetooth, probe every device. The HID++ driver
will fall back to plain HID if the device does not support HID++,
or to a another device-specific driver if it is part of the
unhandled_hidpp_devices array, used in the match function.
Note that this change might cause upower to export 2 batteries for
certain Bluetooth LE devices which export their battery information
through the Bluetooth BATT profile. This particular bug is tracked at:
https://gitlab.freedesktop.org/upower/upower/-/issues/166
Tested with a Logitech Signature M650 mouse, over Bluetooth
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Export hid_match_id() so it can be used in device-specific drivers to
implement their own matching with open-coding a match function.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the new PIDs to wacom_wac.c to support the new model in the Intuos Pro series.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can dereference a null pointer trying to queue work to a destroyed
workqueue.
If the device is disconnected, nintendo_hid_remove is called, in which
the rumble_queue is destroyed. Avoid using that queue to defer rumble
work once the controller state is set to JOYCON_CTLR_STATE_REMOVED.
This eliminates the null pointer dereference.
Signed-off-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add device ID of Meteor Lake P into ishtp support list.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 87562fcd13 ("HID: input: remove the need for HID_QUIRK_INVERT")
made the assumption that it was the only one handling tablets and thus
kept an internal state regarding the tool.
Turns out that the uclogic driver has a timer to release the in range
bit, effectively making hid-input ignoring all in range information
after the very first one.
Fix that by having a more rationale approach which consists in forwarding
every event and let the input stack filter out the duplicates.
Reported-by: Stefan Hansson <newbie13xd@gmail.com>
Fixes: 87562fcd13 ("HID: input: remove the need for HID_QUIRK_INVERT")
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The touchbar on Apple T2 Macs has 2 modes, one that shows the function
keys and other that shows the media controls. The user can use the fn
key on his keyboard to switch between the 2 modes.
On Linux, if people were using an external keyboard or mouse, the
touchbar failed to change modes on pressing the fn key with the following
in dmesg :-
[ 10.661445] apple-ib-als 0003:05AC:8262.0001: : USB HID v1.01 Device [Apple Inc. Ambient Light Sensor] on usb-bce-vhci-3/input0
[ 11.830992] apple-ib-touchbar 0003:05AC:8302.0007: input: USB HID v1.01 Keyboard [Apple Inc. Touch Bar Display] on usb-bce-vhci-6/input0
[ 12.139407] apple-ib-touchbar 0003:05AC:8102.0008: : USB HID v1.01 Device [Apple Inc. Touch Bar Backlight] on usb-bce-vhci-7/input0
[ 12.211824] apple-ib-touchbar 0003:05AC:8102.0009: : USB HID v1.01 Device [Apple Inc. Touch Bar Backlight] on usb-bce-vhci-7/input1
[ 14.219759] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 24.395670] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 34.635791] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 269.579233] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 1 (-110)
Add the USB IDs of the touchbar found in T2 Macs to HID have special
driver list to fix the issue.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to the Surface Go devices, the Elantech touchscreen/digitizer in
the Lenovo Yoga C630 mistakenly reports the battery of the stylus, and
always reports an empty battery.
Apply the HID_BATTERY_QUIRK_IGNORE quirk to ignore this battery and
prevent the erroneous low battery warnings.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Google Chromebooks use Chrome OS Embedded Controller Sensor Hub instead
of Sensor Hub Fusion and leaves MP2 uninitialized, which disables all
functionalities, even including the registers necessary for feature
detections.
The behavior was observed with Lenovo ThinkPad C13 Yoga.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add device id for the Sparco R383 Mod wheel.
Fix wheel info array length to match actual wheel count present in the array.
Signed-off-by: Michael Hübner <michaelh.95@t-online.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need for a driver to individually add/create device groups,
the driver core will do it automatically for you. Convert the
hid-vivaldi core driver to use the dev_groups pointer instead of
manually calling the driver core to create the group and have it be
cleaned up later on by the devm core.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a timing issue captured during ishtp client sending stress tests.
It was observed during stress tests that ISH firmware is getting out of
ordered messages. This is a rare scenario as the current set of ISH client
drivers don't send much data to firmware. But this may not be the case
going forward.
When message size is bigger than IPC MTU, ishtp splits the message into
fragments and uses serialized async method to send message fragments.
The call stack:
ishtp_cl_send_msg_ipc->ipc_tx_callback(first fregment)->
ishtp_send_msg(with callback)->write_ipc_to_queue->
write_ipc_from_queue->callback->ipc_tx_callback(next fregment)......
When an ipc write complete interrupt is received, driver also calls
write_ipc_from_queue->ipc_tx_callback in ISR to start sending of next fragment.
Through ipc_tx_callback uses spin_lock to protect message splitting, as the
serialized sending method will call back to ipc_tx_callback again, so it doesn't
put sending under spin_lock, it causes driver cannot guarantee all fragments
be sent in order.
Considering this scenario:
ipc_tx_callback just finished a fragment splitting, and not call ishtp_send_msg
yet, there is a write complete interrupt happens, then ISR->write_ipc_from_queue
->ipc_tx_callback->ishtp_send_msg->write_ipc_to_queue......
Because ISR has higher exec priority than normal thread, this causes the new
fragment be sent out before previous fragment. This disordered message causes
invalid message to firmware.
The solution is, to send fragments synchronously:
Use ishtp_write_message writing fragments into tx queue directly one by one,
instead of ishtp_send_msg only writing one fragment with completion callback.
As no completion callback be used, so change ipc_tx_callback to ipc_tx_send.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The double `like' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove a left-over from commit 2874c5fd28 ("treewide: Replace GPLv2
boilerplate/reference with SPDX - rule 152").
An empty comment block can be removed.
While at it remove, also remove what is supposed to be the path/filename of
the file.
This is really low value... and wrong since commit 471d17148c
("Input: wacom - move the USB (now hid) Wacom driver in drivers/hid")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On an Asus G513QY, of the 5 bytes in a 0x5a report, only the first byte
is a meaningful keycode. The other bytes are zeroed out or hold garbage
from the last packet sent to the keyboard.
This patch fixes up the report descriptor for this event so that the
general hid code will only process 1 byte for keycodes, avoiding
spurious key events and unmapped Asus vendor usagepage code warnings.
Signed-off-by: Josh Kilmer <srjek2@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix the following coccicheck warning:
drivers/hid/hid-rmi.c:240: WARNING opportunity for min().
drivers/hid/hid-rmi.c:350: WARNING opportunity for min().
min() macro is defined in include/linux/minmax.h. It avoids
multiple evaluations of the arguments when non-constant and performs
strict type-checking.
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Michael Zaidman